BEA EAGLE ONE HM User Manual

Page 1
EAGLE ONE HM
* Other use of the device outside of the permitted purpose can not be guaranteed by the manufacturer.
ENGLISH
User’s Guide for product version 0600 and higher See product label for serial number
DESCRIPTION
1
2
1. main connector
2. antenna
3. push buttons
4. cover
TECHNICAL SPECIFICATIONS
Technology: Transmitter frequency: Transmitter radiated power: Transmitter power density: Detection mode: Min. detection speed: Supply voltage: Mains frequency: Max power consumption: Output: Max. contact voltage: Max. contact current: Max. switching power: Mounting height: Degree of protection: Temperature range: Dimensions: Tilt angles: Material: Weight: Cable lenght: Conformity:
UNIDIRECTIONAL OPENING SENSOR FOR HIGH MOUNTING ON AUTOMATIC DOORS*
microwave and microprocessor
24.150 GHz < 20 dBm EIRP < 5 mW/cm² motion 5 cm/s 12V to 24V AC ±10%; 12V to 24V DC +30% / -10% 50 to 60 Hz < 2 W relay (free of potential change-over contact) 42V AC/DC 1A (resistive) 30W (DC) / 60VA (AC) from 4 m to 5 m IP54 from -20 °C to + 55 °C 120 mm (L) x 80 mm (H) x 50 mm (W) 0° to 90° vertical; -30° to +30° lateral ABS 215 g
2.5 m RED 2014/53/EU, RoHS 2 2011/65/EU
Specifications are subject to changes without prior notice.
3
Measured in specific conditions.
4
This user’s guide is an informative document and
can not be se en as a commitment of result.
Page 2
OPENING THE SENSOR
1
Before fixing After fixing
MOUNTING & WIRING
2
TIPS
parts.
APPLICATIONS
Wall mounting above sliding or revolving door
1
Apply the mounting template. Drill 1 hole for the cable and pull it through. Drill 2 holes for the screws.
Do not cover the sensor.Avoid vibrations.Do not touch electronical
Mounting on door axis (swing doors)
2
Connect the wires accordingly:
1 - BROWN - POWER SUPPLY 2 - GREEN - POWER SUPPLY 3 - WHITE - COM 4 - YELLOW - NO 5 - YELLOW - NC
or
Avoid proximity to neon lamps or moving objects.
Ceiling mounting in front of door (sliding, revolving or swing doors)
3
Position the cable as indicated. Fix the sensor firmly.
EAGLE ONE HM
Page 3
MECHANICAL ADJUSTMENTS
3
1
ANGLE
Adjust the lateral antenna angle.
2
Adjust the vertical antenna angle.
SETTINGS
4
(by remote control or push buttons)
FIELD SIZE
IMMUNITY FILTER
DETECTION MODE
OUTPUT CONFIGURATION
HOLD-OPEN TIME
MOUNTING HEIGHT
DOOR CONTROL
RESET TING TO FACTORY VALUES:
FIELD SIZE
XXS XS S > > > > L XL XXL
low
bi uni
A
0.5 s 1 s 2 s 3 s 4 s 5 s 6 s 7 s 8 s 9 s
4 m > 4 m
auto
high
normal
uni
PRM
P
open closed
FACTORY VALUES
XS, XXS
... S,
> > > >>
uni
AWAY
A = active output (NO-contact) P = passive output (NC-contact)
open = the sensor detects constantly. The LED is ON. closed = the sensor is in standby and does not detect. The LED is OFF.
bi = two-way detection; uni = one-way detection towards sensor
PRM &
uni PRM = one-way detection also of people with reduced mobility
AWAY
uni AWAY = one-way detection away from sensor
OR
highest
> 2 seconds
+
... L, XL, XXL
EAGLE ONE HM
Page 4
©BEA | Original instructions | 42.7974 / V3 - 07.18
ACCESS CODE
The access code (1 to 4 digits) is recommended to set sensors installed close to each other.
SAVING AN ACCESS CODE:
DELETING AN ACCESS CODE:
Once you have saved an access code, you always need to enter this code to unlock the sensor. If you forget the access code, cut and restore the power supply. During 1 minute, you can access the sensor without introducing any access code.
TROUBLESHOOTING
The door remains closed. The LED is OFF.
The door does not react as expected.
The door opens and closes constantly.
PLEASE KEEP FOR FU RTHER USE - DESIGNED FO R COLOUR PRIN TING
The door opens for no apparent reason.
The LED flashes quickly after unlocking.
The sensor does not respond to the remote control.
The sensor power is off.
The door control setting (F2) is set to value 3 (closed).
Improper output configuration on the sensor.
The sensor is disturbed by the door motion or vibrations caused by the door motion.
It rains and the sensor detects the motion of the rain drops.
In highly reflective environments, the sensor detects objects outside of its detection field.
In airlock vestibules, the sensor detects the movement of the opposite door.
The sensor needs an access code to unlock.
Batteries in the remote control are weak or installed improperly.
Remote control badly
Check the wiring and the power supply.
1
Change the door control setting (F2) to value 1
1
(automatic).
Change the output configuration setting on
1
each sensor connected to the door operator.
1
Make sure the sensor is fixed properly.
2
Make sure the detection mode is unidirectional.
3
Increase the antenna angle.
4
Increase the immunity filter.
5
Reduce the field size.
1
Make sure the detection mode is unidirectional.
2
Increase the immunity filter.
3
Install the ORA (rain accessory).
Change the antenna angle.
1
Decrease the field size.
2 3
Increase the immunity filter.
Change the antenna angle.
1 2
Change the antenna.
3
Increase the immunity filter.
Enter the right access code.
1
If you forgot the code, cut and restore the power
2
supply to access the sensor without access code. Change or delete the access code.
1
Check and change the batteries if necessary.
Point the remote control towards the sensor.
1
pointed.
BEA SA | LIEGE Science Park | ALLÉE DES NOISETIERS 5 - 4031 ANGLEUR [BELGIUM] | T +32 4 361 65 65 | F +32 4 361 28 58 | INFO@BEA.BE | WWW.BEA-SENSORS.COM
BEA hereby declares that the EAGLE ONE HM is in conformity with the basic requirements and the other relevant provisions of the directives RED 2014/53/EU and RoHS 2 2011/65/EU. The complete declaration of conformity is available on our website.
Only for EC countries: According to the European Guideline 2012/19/EU for Waste Electrical and Electronic Equipment (WEEE)
Loading...