1/2
EAGLE 5&6
USER’S GUIDE
UNIVERSAL MOTION SENSORS FOR AUTOMATIC DOORS
JST-connector
Brown
Green
Power supply
White Relay (COM)
Yellow Relay (NO)
Sensitivity potentiometer
LED - flashes after power-on
- lights up during detection
Dip switch
Planar antenna
for wide detection field
1
Dip switch settings
EAGLE 5
DIP SWITCH 1
Detection mode
DIP SWITCH 2
Relay configuration
DIP SWITCH 3
MTF-mode
DIP SWITCH 4
Immunity
▼ OFF
Bidirectional mode Active output Unidirectional without MTF Normal immunity
▲ ON
Unidirectional mode Passive output Unidirectional with MTF Increased immunity
EAGLE 6
DIP SWITCH 1
Detection mode
DIP SWITCH 2
Relay configuration
DIP SWITCH 3
MTF-mode
DIP SWITCH 4
Immunity
▼ OFF Bidirectional mode
Active output - Normal immunity
▲ ON
- Passive output - Increased immunity
2
The sensitivity settings determine the size of the sensing field
MIN
MAX
MIDDLE
vertical angle: 30°, mounting height: 2.2m
3
The lateral angle of the planar antenna determines the position of the sensing field
4
The vertical angle of the planar antenna determines the depth of the sensing field
15°
30° 45°
30°
45°
15°
0°
21 01 2
1
2
3
1
2
3
15
30
45
sensitivity: maximum
1 General information
2 Adjustments
2/2
Avoid vibrations! Do not cover the sensor! Avoid moving objects
in proximity of the sensor!
Avoid HF lamps or
fluorescent lighting
in proximity of the sensor!
Avoid touching
electronics!
Technology : microwave and microprocessor
Transmitter frequency : 24.175 GHz
Transmitter radiated power : <20 dBm EIRP
Transmitter power density : < 5mW/cm²
Maximum mounting height : 3m
Tilt angles : 0° to 90° vertical and -30° to + 30° lateral
Detection field (mounting height=2.2m) : 4m (W) x 2m (D)
Detection mode : motion
Minimum speed : 5 cm/s (measured in the sensor axis)
Supply voltage : 12V to 24V AC/DC +30% / -10%
Mains frequency : 50 to 60 Hz
Power consumption : < 2W (VA)
Output relay (free of potential change-over contact)
Max. contact voltage
Max. contact current
Max. switching power
: 42V AC- 60V DC
: 1A (resistive)
: 30W (DC) / 60VA (AC)
Hold time : 0.5s
Temperature range : -20°C to +55°C
Degree of protection : IP54
Norm Conformity : R&TTE 1999/5/EC; EMC 89/336/EEC
Material : ABS
Color of housing : black smoked, aluminium finish
Dimensions : 120mm (W) x 80mm (H) x 50mm (D)
Weight : 0.215kg
Length of cable : 2.5m
EBA ECA ERA Planar antenna for narrow detection field
SYMPTOMS PROBABLE CAUSES CORRECTIVE ACTION
The door will not open and no red LED
lights up.
The sensor power is off. Check the wiring and the power supply.
The door opens and closes constantly. The sensor "sees" the door moving. Increase the tilt angle and/or reduce the sensitivity.
When closing, the door creates
vibrations picked up by the sensor.
Make sure that the sensor is correctly fixed.
Switch to unidirectional mode (dip switch 1: ON).
Increase the immunity (dip switch 4: ON).
Reduce the sensitivity.
The door will not close.
Red LED is OFF.
ON-OFF switch at door control is in
wrong position or faulty.
Improper output configuration.
Make sure that the ON-OFF switch for the door is in the ON or
AUTOMATIC position. Check the output configuration setting
on each sensor connected to the door operator.
It rains and the sensor detects for no
apparent reason.
The sensor detects the motion of the
rain drops.
Use the ERA accessory. Switch to unidirectional mode and
increase the immunity (dip switches 1&4: ON).
3 Installation tips
4 Troubleshooting
5 Technical specifications
6 Accessories
(sold individually)
Liege Science Park – Allée des Noisetiers 5, Angleur – BELGIUM – TEL +32.4.361.6565 – FAX +32.4.3612858 – E-mail: info@bea.be – www.beasensors.com
69.?0620/ V1 – 09.12
Loading...