Baumfolder BAUM20 Ifold Operation Manual

Download

TP10509

IFOLD

OPERATORS

MANUAL

TABLE OF CONTENCE

TP10509

IFOLD STARTUP PROCEDURES………..................…...PAGE 1

IFOLD SHUTDOWN PROCEDURES…………................PAGE 1

SCREEN MAINTAINENCE……………….....................….PAGE 1

WARRANTY NOTE………………….……………..............PAGE 1

MAIN SCREEN HELP…………………..........................…PAGE 2

FOLD SELECT HELP………………………..….................PAGE 5

PAPER SELECT HELP……………………..................…..PAGE 6

SUMMARY PAGE HELP………………………..................PAGE 9

ADJUST PARALLEL HELP………………........................PAGE 13

MAINTENANCE HELP…………………...............….……PAGE 16

JOB CALCULATOR HELP………………….............…….PAGE 17

IFOLD PARTS MANUAL……………………..............……PAGE 18

IFOLD SCHEMATIC……………………………….........….PAGE 29

TP10509

Page 1 of 29

Start up procedures The I-Fold software should start-up automatically when the

machine is turned on. If for any reason it does not start up properly cycle power to the machine. If the I-Fold software still will not start up contact your local dealer for support.

Shut down procedures It is very important to shut down the I-Fold properly before

turning off the machine. Before powering down the machine press the

button to start the power down procedure. A pop up box will

appear asking if you are sure you want to power down. Press OK. From this point the power down is automatic. Once the screen reads it is OK to turn off your computer you can shut down the machine.

Cleaning Touch Screen computer

It is very important to shut down the I-Fold computer before cleaning the computer screen. Use a CRT screen cleaner ONLY on the interface touch screen.

Warranty Note

WARNING – Damage to the computer screen will occur if any instrument other than the operator’s finger is used to navigate the I-Fold screens. NOTE: Warranty on the computer will be void if this is found to be the case for the computer failure.

Touch this button to change from

TP10509

Page 2 of 29

standard, decimal, standard fractional

or metric.

This shows the count and rate from the

machine display. This is reset from the

machine control panel (see the operators

manual for instructions). Touch the numbers

in the count box to make the count display

larger and touch it again to change it back.

Touch this button to change the language. English,

Spanish, German or French.

Touch this button to go to the

summary screen for the current job.

The summary screen shows all of your

settings and any notes you want to add

Touch this button to setup a new job

Touch this button to recall a previously

saved job

Touch this button to see parts and

operators manuals for your machine.

Touch this button for troubleshooting

help with any problems you may be

having

Touch this button before turning off

the machine. Once the screen says it is

safe to turn off your computer then

you can turn off the machine

TP10509

Page 3 of 29

Touch this button to bring up

a job calculator that will help

you determine how long a job

will take.

When this box is red it indicates

you have made a change to the

setup. This change will be lost if the

system is powered down. If you

would like to save this change touch

this button

When this box is red it indicates

there is a maintenance item that

needs your attention. You can

touch this button anytime to see

recommended maintenance items

and how to do them.

station) the buttons will not be displayed.

station) or a 16 page(3

section. You can also make changes to these settings if necessary. If you do not have an 8 page(2

Touch these buttons to see the current settings for the fold plates and Baumsets for the indicated fold

TP10509

Page 4 of 29

This box contains the current work order.

Touch the box to enter a new work order.

When you touch the box a keyboard will pop

up, Just enter the work order and touch enter.

This box contains the initials of the operator

currently logged on. ??? indicates no

operator is currently logged on. Touch the

box to log on. A keyboard will pop up.

If this is the first time you have logged on touch the

NEW button then type your name and touch enter. It

will ask for a password, if you do not enter a password

at this time you will never be ask for one in the future.

If you type a password and touch enter you will need

to enter this password every time you log in. If you

have logged in before just type in your initials and

touch enter then type in a password and touch enter if

necessary.

TP10509

Page 5 of 29

in the box to the left.

Press here to select the fold displayed

This box show the available folds. Touch a button to see the fold in the box on the left.

Touch the ► Arrow at the bottom of the page to see the next pages. Press the ◄ to come

back to this page. A on the button indicates the fold is not possible with you current

configuration.

circle indicates the opposite side

This box shows the selected fold. A color in a

determine for the selected fold.

and the label will come out face up on the stacker. Panels indicates the number of panels in a

Paper orientation shows how to load the paper and how the address or label will come out on

the stacker. Example: Load the address or label down and forward (toward the sucker wheel)

roll or accordion fold. If the stacker display shows none, the output on the stacker is difficult to

Touch one of these boxes to select a paper size.

TP10509

Page 6 of 29

A on the button indicates that paper size will not run on your machine

from inch to metric

Touch this box to change

button.

down and forward). You can change this from portrait

(shown) to Landscape and back by touching the orientation

This box shows how the paper is loaded (label or address face

size. Do this for both the width and length.

a keypad will pop up. Using the keypad enter the paper custom paper

Touch these boxes to enter a custom paper size. When you touch a box

the main screen.

TP10509

Page 7 of 29

Touch this button to go to

feeder setup screen.

Touch this button to go to the

activate the see setup list and to feeder setup buttons.

and orientation to fold/paper setup completed. This will also

been selected. The text will change from select this paper size

Touch this box once the desired paper size and orientation have

setup list is explained on the next page.

Touch this button to see the setup list. The

the summary screen.

Touch this button to go to

Touch this button to go back

to the fold select screen.

This will come up on the left of any setup screen when the see setup list

TP10509

Page 8 of 29

button is touched. This list shows all of the setup screens needed for the

selected fold. You can go to any screen on the list just by touching the

corresponding button. The done button shows a green checkmark when the

page is completed and the press when setup complete button has been

touched. This can help you keep track of where you are in the setup of the

job. You can also set the done button to a green checkmark by touching it

when this list is up. To close the setup task list without going to a different

page just touch the close button.

save job screen.

TP10509

Page 9 of 29

the setup list. The setup

Touch this button to see

list is explained on page 4.

needs 1 sheet of paper and fold plate number 1 is set to 8 ½ inches to do the selected fold. Touch

blue or gray boxes indicate the fold plate setting. Example: On the parallel station gapset number 1

station required to do the selected fold. The black boxes indicate the gapset and fold plate numbers,

These areas show the number of sheets that go under each gapset and the fold plate settings for every

the dark blue boxes indicate the number of sheets that go under the corresponding gapset and the light

you can make any changes needed to the number of sheets in the gapsets or the fold plate settings.

anywhere in each area and it will take you to the corresponding adjustment screen, from that screen

This area shows the feeder settings.

Where to set the non-operator side paper

guide and the blow tube settings.

This area shows the suggested scoring

dies for each station to run the selected

fold.

blue box under the fold saved name to go to the

is saved what name it is saved under. Touch the

This area shows the current fold selected and if it

TP10509

Page 10 of 29

In this area you can enter up to 4 notes with up to 55 characters per note to be saved with a fold job. These

could contain information like what speed it ran best at if it needed a slit or a perf and what type of perf. To

enter a note just touch one of the gray lines next to a note: and a keypad will pop up (see the next page).

TP10509

Page 11 of 29

button or the Ent button.

Use the keypad to enter a note, the clear button will clear everything in the display, this is

recommended if you are entering a new note. The Ins/Del button is used to control what happens

when you touch the arrow buttons. If the button displays Ins you are in insert mode the < and >

buttons will move the curser left or right then anything you type will be inserted where ever the

curser is located. If you Touch the button it will change to Del now you are in delete mode, if you

touch the < button it will delete the character to the left of the curser and if you touch the >

button it will delete the character to the right of the curser. After you are finished typing your note

touch the Ente

TP10509

Page 12 of 29