Page 1
GB
DYNAMIC SENSE: Energy savings and optimum wash results
The two sensor-controlled “DYNAMIC SENSE” wash options are
recommended for routine washes. They use double-sensor
technology. Separate sensors gauge turbidity and particles in order to
determine the degree of soiling of the wash water. In accordance with
values measured, a microprocessor establishes optimum water,
energy and time consumption. Optimum wash results are thus
achieved using only those resources strictly required.
GSI 7494
Further indications are given in the pages to follow and in the user instructions.
Rinse aid level indicator
Add rinse aid.
Salt level indicator
Add regeneration salt; only add
regeneration salt immediately before
starting a wash programme.
Programme progress indicator
Pre-rinse /Pre-wash
Washing
Drying
Programme end
Programme Symbol
and Temperature
Eco Normal 40 - 55° C
Intensive 60 - 70° C
Pre-wash
Rapid 40° C
Recommended programme
with little or no dried-on food.
Recommended programme
dried-on food. Especially suitable for pans and saucepans.
Crockery to be washed later.
Lightly soiled crockery with no dried-on food.
Half Load button
This function can be used with any programme.
The indicator lamp switches on: the wash cycle is
activated for the upper or lower rack
Delayed start button
The wash cycle can be programmed to start after
1-24 hours. With each successive touch of the
button, the delayed start indicator increases
by 1 hour, and after 24 returns to 00.
Then press the Start button.
The wash programme will start at the set time.
Programme selection and
recommended load type
for heavily soiled crockery
Quick Reference Guide
Options
.
only
Place the detergent in the:
compartment compartment
for routine washes
, for crockery
, with
Programme selector
Time and failure display
Indicates in hours the time remaining until the start of the wash cycle.
Switches off when the programme has started. Toward the end of the
programme, during the drying cycle, the display will indicate the time
remaining in minutes.
“F1-F4”, “F7-F9”
” Turn on the water supply tap.
“F6
Start button
Indicator lamp lit while the dishwasher is operating .
Flashes when a fault occurs.
Switches off at the end of the programme.
small large
X X
X X
- - 5.0 (4.2) 0.02 (0.02) 9(9)
- X 13.0 (13.0) 0.85 (0.75) 30 (30)
Identification of faults for service technician.
Consumption
1)
Normal load / (Half load)
Water
(Litres)
(13.5)
(11.5)
(19.5)
(11.5)
Energy
(kWh)
Time
(Min.)
(1.3)
(0.9)
(1.7)
(1.3)
(80)
(60)
(98)
(90)
Glasses 40° C
Bio-Normal 50 °C
1) Values may vary in relation to usage, e.g.: different loads, water
temperatures - above or below 15° C - as well as water hardness and power su pply voltage etc.
2) Reference programme for Test Institute and energy-label.
Light soiling, especially glasses and cups.
Normally or heavily soiled crockery with dried-on food.
2)
- X 12.0 (10.0) 0.82 (0.78) 60 (59)
X X 16.0 (14.5) 1.03 (0.90) 120 (117)
5019 100 90320
(We reserve the right to make technical modifications)
Page 2
A
A
C
A
How to use the dishwasher
1. After loading the dishwasher, close the
door properly and open the water
supply tap.
2. The dishwasher switches on
automatically as soon as the
programme selector knob is turned.
One of the programme indicator
lamps will switch on.
3. Turn the selector knob to select the
desired programme.
indicator lamp lights up.
select options (if supplied).
4. Press the Start button to start the
selected programme.
indicator lamp will light up.
the programmed data cannot be
altered by turning the programme
selector knob.
once the Start button has been
Note:
pressed, the dishwasher memorises the
last programme selected. This
information remains in the memory even
during interruption of the power supply.
To change the selected
programme, press the Start button
for about 5 seconds
Start indicator lamp switches
Select a new programme
off.
using the programme selector
knob and press the Start button.
if the dishwasher is switched off
Note:
during a wash programme, when
switched on again it will resume the wash
cycle from where it was interrupted.
Only open the dishwasher door if
strictly necessary during a wash
cycle and exercise maximum
caution. Danger of scalding from
steam.
5. To indicate the end of the programme,
the Start indicator lamp switches off
and
the End indicator lamp (if fitted)
switches on
The corresponding
If required,
The Start
Once set,
, until the
(for about 30 min.)
.
6. Turn the programme selector knob
counter clockwise to the initial position to
switch off the dishwasher (only after the
Start indicator lamp has switched off).
the indicator lamps switch off.
7. Open the door (warning: beware of hot
steam). Unload the lower rack before
the upper one. Close the water tap.
Upper rack
B
Half Load:
If the upper rack
the cutlery basket
Rack height adjustment:
(The dishwasher is delivered with the
upper rack in the top position).
The rack height can also be chan ged
when loaded.
is to be loaded, place
only
in the upper rack.
“B”
Please read the user instructions carefully.
• To lower: pull out the
handles and gently lower the rack.
• To raise: pull up the
All
until the rack clicks into place.
• The rack must be level on both
sides.
two
two
Crockery holders:
• Down: cups and long-stemmed glasses.
•
Up: plates.
“Vario Organizer” multi-purpose
support:
• To be used, for example, for longhandled utensils
with the blade facing downwards),
cups and glasses.
• May be used in three different
positions (see also “Dishwasher
loading instructions” on Page 4).
1. Upon the left-hand side of the rack.
2. Upside-down, towards the centre of
the rack.
3. Upside-down, towards the left side.
(arrange knives
Glass holder:
Upper and lower rack
side
side handles
Half Load:
Loading the lower rack
greater washing power, especially for
plates and saucepans.
Plate holders:
• May be lowered to increase
available space (A).
Cutlery basket:
• The cutlery basket can be removed
to increase (B + C) available space.
• Some models are provided with
a grid (D) that can be fitted onto
the cutlery basket.
B
Lower rack
only
C
gives
D
Page 3
Tips and advice
• Arrange crockery so that items do not
touch each other. Arrange large
crockery in the lower rack and smaller
crockery in the upper rack.
• Load cups at an angle to facilitate
water drainage.
• Generally speaking, place cutlery in the
basket with the handles positioned
downwards, but ensure that any sharp
knives and forks that might cause
injury are placed in the basket with the
handles positioned upwards.
• Make sure the water jet can reach all
loaded items and that the spray arms
turn freely.
Important
• Fill the detergent dispenser and check
the salt and rinse aid level.
• Do not use the appliance for items not
suitable for washing in a dishwasher,
for example: wooden items, aluminium,
plastic utensils, tin, hand-decorated
crockery (unglazed), silver cutlery.
• Do not put liquid fat in the dishwasher
(e.g. oil used for frying) or candle wax.
• If a fault occurs or you wish to change
the current programme, press the
“START” button for about 5 seconds until
the Start indicator lamp switches off.
• If regeneration salt is to be added,
immediately
in order to eliminate any residual salt
(rinsing alone is not sufficient).
• Sometimes even though the
regeneration salt container has been
filled, the corresponding indicator lamp
(if fitted) will light up during the first
wash cycle after filling with salt.
start a wash programme
• Before starting a wash programme,
make sure that the spray arms can turn
freely and are not impeded by crockery
or cutlery.
• Switch off the dishwasher once the
“Start” indicator lamp has switched off.
If you switch off the dishwasher during
a wash cycle, when switched on again
the dishwasher resumes the cycle from
where it was interrupted without h aving
to start it again.
If a fault occurs, before contacting our
After-Sales Service, make the following
checks to try and remedy the problem:
The dishwasher is not working:
• Is the plug properly inserted in the wall
socket?
• Is there a power failure?
• Is the dishwasher switched on?
• Has the Start button been pressed?
• Has the delayed start timer been set (if
fitted)?
• Is the wat er supply tap on?
• Is the flow of water obstructed by impurities?
If so, close the water supply tap, detach the
water hose and clean the filter. Then
re-connect the water hose to the tap and
open the water tap once again.
• Are the filters clogged? (See “Care and
Maintenance” chapter in the user
instructions).
• Is the door cl osed properly?
• Is a fault i ndicated?
(The Start indicator lamp flashes).
Start the programme again from the
beginning: press the Start button for
about 5 seconds, until the Start indicator
lamp switches off.
Select a new programme and press the
Start button.
Troubleshooting Guide
Crockery still dirty after washing:
• Was the crockery lo aded properly?
• Crockery must be loaded facing
downwards; this is important, especially
for large items of crockery.
• The water jet s must spray the entire
surface of all items.
• Make sure that crockery and cutlery are
arranged properly.
• Have you selected the correct programme?
• Did you use too much or too little
detergent? (The use of poor quality
detergents may result in less effective
washing).
• Are the filters clogged or incorrectly
assembled? (See “Care and
Maintenance” chapter in the user
instructions).
• Are the spray arms blocked or the nozzles
clogged? (See “Care and Maintenance”
chapter in the user instructions).
• Is the lower spray arm correctly fitted?
• Is the salt container cap (water softening
system) screwed down?
Marked crockery:
• Is the water hardness level selector not
properly adjusted? See (“Filling the salt
container” in the user instructions).
• Is the salt container empty? (See “Filling
the salt container” in the user
instructions).
• Was insufficient detergent used? (See
“Filling the detergent dispenser” in the
user instructions).
Marked glasses and cutlery:
• Was too much rins e aid used? (See
“Filling the rinse aid dispenser” in the user
instructions).
Note:
with some models, when the Start
button is pressed a pre-wash cycle precedes
the actual wash programme; this
regenerates the water softening system.
AFTER-SALES
SERVICE
If after carrying out the above checks
the malfunction persists or appears
again, turn the appliance off and turn
off the water supply tap, then call our
After-Sales Service (see guarantee).
Please specify:
• The nature of the fault.
• The applia nce type and model.
• The service code (the number after
the word Service on the adhesive
rating plate) inside the door
on the right-hand side.
Your full address and telephone number.
•
Please read the user instructions carefully.
Page 4
Dishwasher loading instructions
UPPER RACK
LOWER RACK
Depending on the model, rack features may vary (see “Upper and lower rack” description).
Half Load
Loading...