Bauknecht GSI 6989 E IN, GSI 6989 E BR, GSI 6989 E WS Quick reference guide

Page 1
GSI 6989
Before using the dishwasher, read the user instructions!
Quick Reference Guide
Wash cycle
GB
Programme selector knob
On / Off button
Start button
Switches “on” when the dishwasher
is operating. Flashes when a fault occurs. Switches off at the end of the programme.
Indicators
Add regeneration salt
Add rinse aid
No water
Check that the appliance fills with water.
Programmes Loading instructions A B
AutoNormal
AutoIntensive
Pre-Rinse cold
Glass 40°C
Rapid 30 min 40°C
Eco
Programme chart
Automatic programme recommended for routine washes, with no dried-on or burnt
40-55°C
food (not for EN 50242). Automatic programme recommended for
heavily soiled crockery with dried-on or burnt
60-70°C
food, for example pans and saucepans. Crockery to be washed later. - - 4.0 0.03 14
Light soiling, for example glasses and cups.
Lightly soiled crockery with no dried-on food.
1)
Normally or heavily soiled crockery. X X 13.0 1.05 120
50°C
Pre-Rinse Washing Drying
Options
Time and failure display
Indicates in hours the time remaining until the start of the wash cycle. Switches off at programme start and indicates the remaining time in hours and minutes.
“F...” Information for the After­Sales Service
“Delayed start” button
The wash cycle can be programmed to start after 1 - 24 hours. With each successive touch of the button, the delayed start indicator increases by 1 hour, and after 24 returns to 00. Then press the Start button. The dishwasher will start at the set time.
“Half load” button
This function can be used with any programme. The indicator lamp switches on. The wash cycle is activated for the upper
or
lower rack
Detergent
X X 10-13 0.8-1.05 50-110
X X 13-20 1.1-2.0 90-140
X - 10.0 0.80 55
X - 10.0 0.65 30
2)
Litres kWh Minutes
Programme
end
3)
only
.
Consumption
3)
1) Reference programme for energy label in compliance with EN 50242 regulations;
2) Refer to “User instructions“;
3) Values may vary in relation to usage, e.g.: different loads, water temperatures - above or below 15°C - as well as water hardness and power supply voltage, etc.
(We reserve the right to make technical modifications)
5019 496 90224
Page 2
How to use the appliance
C
BA
Further indications are given in the single chapters and in the user instructions.
Switch on the appliance
How to fill the
detergent dispenser
Check the
rinse aid level
Check the regeneration
salt level
Load the racks
Close the door,
turn on the water tap
Select a programme
Press the ON/ OFF button.
Large compartment With each wash cycle. Small compartment For programmes with pre-wash only.
Mechanical indicator lamp C. Electric indicator on control panel (if provided).
On models with water softener system only.
Mechanical indicator lamp D. Electric indicator on control panel (if provided).
Refer to the dishwasher loading instructions.
The last programme selected will light up. Select the desired programme (using the specific button or knob). The corresponding indicator lamp lights up.
A:
B:
Select additional
options
Press the START button
Wash cycle
Switch off the appliance
Shut off the water tap,
unload the racks
If necessary (and if provided) the corresponding indicator lamp lights up.
The selected programme is then memorised (even in the event of power failure).
Only after the START button has switched off: Press the
OFF
ON /
Warning: when the door is opened steam comes out!
Unload the appliance, starting from the lower rack.
button. All the indicator lamps switch off.
“Change programme”
Press the START button for 2 sec. until the Start indicator lamp switches off;
Select another programme and press the START button again.
- Only open the dishwasher if necessary (Warning: beware of hot steam).
- If the appliance is switched off during a wash cycle, when switched on again it will resume the cycle from where it was interrupted.
Page 3
Dishwasher loading instructions and racks provided
Upper rack:
Multi-purpose support (A)
Depending on the position, for long-handles utensils, cups and glasses. May be used in three different positions.
Crockery holders (B):
Depending on the position, for example plates, cups and long-stemmed glasses.
Revolving glass support (C)
Depending on the position, for example small or long­stemmed glasses.
1)
Half Load:
Load the upper rack Place the cutlery basket (D) in
the upper rack.
only
.
Rack height adjustment (also when loaded):
Lower adjustment:
• out the
two
rack handles outwards (E) and lower the rack.
Upper adjustment:
two
handles (E) upwards until the rack clicks into place (Factory setting).
The rack must be level on both sides.
pull
pull the
depending on the model
:
2)
:
Lower rack:
Depending on the model with fixed or tilting plate holders (F).
Half Load:
Load the lower rack Greater washing power,
particularly for plates and saucepans.
only
.
Cutlery basket (G) or (H):
Some models are provided with a grid (I) that can be fitted onto the cutlery basket to keep items separated. Cutlery basket (D) for appliances with half load only. Sharp knives and forks that might cause injury must be placed in the cutlery basket with the handles positioned upwards.
Do not use the appliance for items not suitable for washing in a dishwasher, for example wooden items, aluminium, plastic utensils, tin, hand-decorated crockery (unglazed), silver cutlery. Spare parts which are sold separately:
1)
Multi-purpose support (A) - N. AMH 369.
2)
Revolving glass support (C) - N. WGH 1000.
Page 4
What to do if...
If a fault occurs, before contacting our After-Sales Service, make the following checks to try and remedy the problem (* see also the corresponding chapter in the user instructions).
Problem Cause Remedy
The appliance is not working
If crockery is not perfectly dry
If crockery is not perfectly clean
Sandy or grainy residues
Colour of plastic parts faded
• No water supply. • Open the tap.
• The appliance does not load sufficient water.
• There is a power failure. • Insert the plug into the mains socket.
• Starting the selected programme. • The programme can be set to “0” to start.
• Insufficient rinse aid. • Increase dosage *.
• Resid ual water in cavities. • Load crockery at an angle.
• The water jet does not reach the crockery.
• I nsufficient detergent. • Follow recommended detergent dosage.
• Unsuitable programme. • Select a more intense wash cycle.
• Spray arms blocked. • T he spray arms must be able to turn freely.
• Spray arm nozzles clogged. • Remove any impurities obstructing the water
• I ncorrect detergent/detergent too old.
• Clogged filters. • Check filters regularly/if necessary clean *.
• Filters incorrectly assembled. • Insert the filter correctly *.
• Tomato/carrot juice... • Depending on the material, if necessary use a
• Clean the water supply tap filter. Ensure there are no kinks in the water hose.
• Press the Start button.
• Close the door.
• Check the domestic circuit fuse.
• Arrange crockery so that items do not touch each other. Load crockery upside down.
flow *.
• Use a good quality detergent.
detergent with a greater whitening power.
Deposits on crockery
•removable • Streaks on the crockery/glasses. • Increase the rinse aid dosage *.
• Streaks on glasses. • Reduce the rinse aid dosage *.
• Layer of salt on crockery/glasses. • Close the salt container lid properly*.
• not removable • I nsufficient water softening,
Opaque glasses/ glasses not sparkling
Rust on cutlery Identifying
calcium deposits.
• Cannot be washed in the dishwasher.
• Not m ad e o f stainless steel. • Use suitable cutlery.
• The START indicator lamp flashes. • Ensure that the filter assembly is not clogged
appliance faults
• Indicator F... (if provided). • Call the After-Sales Service.
If after carrying out the above checks the malfunction persists or appears again, turn the appliance off and turn off the water supply tap, then call our After-Sales Service (see guarantee).
Before contacting our After-Sales Service, take note of the following:
• The nature of the fault.
• The appliance type and model.
• The service code (the number indicated on the adhesive rating plate) inside the door on the right-hand side.
• Change water hardness setting, if necessary add salt *.
• Use suitable glasses.
and if necessary clean it *. Start the programme again. Press the START button for about 2 seconds, until the START indicator lamp switches off. Select a new programme and press the Start button again.
Loading...