Bauknecht GSI 5919/1 IN BK, GSI 5919/1 SW BK, GSI 5919/1 WS BK Quick Reference Guide
Before using the dishwasher, read the user instructions!
GSI 5919
Indicators
Quick Reference Guide
Programme selection button
On / Off button
Start button
Switches “on” when the dishwasher is operating.
Flashes when a fault occurs. Switches off at the
end of the programme.
Add regeneration salt
Only add regeneration salt immediately
before starting a wash programme.
Add rinse aid
Options
GB
3)
Time and failure display
Indicates in hours the time remaining until the start of
the wash cycle. Switches off at programme start and
indicates the remaining time in hours and minutes.
“F....” Information for the After-Sales Service
“Delayed start” button
The wash cycle can be programmed to start after
1 - 24 hours. With each successive touch of the
button, the delayed start indicator increases by 1
hour , and after 24 returns to 00. Then press the Start
button. The dishwasher will start at the set time.
“Half load - Multizone” button
Load the upper or lower rack
This function can be used with any programme.
Press once = upper rack
(the indication lamp/symbol comes on)
Press twice = lower rack
(the indication lamp/symbol comes on)
Press 3 times = Off (half load function deactivated).
When washing without the top rack, press the
“Half Load” button twice, or “Lower rack wash”
(the corresponding LED/symbol comes on).
Antibacterial rinse
This function adds an antibacterial rinse at the end
of the wash cycle, thereby guaranteeing a perfectly
clean and sanitized load. The lamp will light up
when the function is activated. If the temperature is
not maintained during the antibacterial cycle (e.g. if
the door is opened and remains open for a long
time), the lamp will start blinking to indicate that
sanitation is not guaranteed.
4) 5)
only
.
Programme chart
Programmes Loading instructions A B
5)
Sensor +
40-70°C
Pre-Rinse cold
Glass 40°C
Rapid 30 min 40°C
1) 5) 6)
Bio
1) Reference programme for energy label EN 50242;
2) Refer to “User instructions”;
3) Programme data obtained in conformity with European
standard EN 50242. Values may vary in relation to usage,
e.g.: different loads, options, water temperatures - above
or below 15°C - as well as water hardness and power
supply voltage, etc.
Important information for Test Laboratories:
For detailed information on the EN comparison test and other tests, contact the following address:
“nk_customer@whirlpool.com”.
50°C
Lightly, normally or heavily soiled
crockery, including pots and pans.
Crockery to be washed later. - - 4.0 0.03 14
Light soiling, for example glasses
and cups.
Lightly soiled crockery with no
dried-on food.
Normally soiled crockery. X X 13.0 1.05 195
4) The bacteria removal efficiency has been tested by the
Institut Pasteur de Lille (France), based on the NF EN
13697 standard of November 2001.
5) These programmes can be used with the Antibacterial
rinse option.
6) Energy saving programme with prolonged drying cycle.
(We reserve the right to make technical modifications)
Detergent
X X 7.0-17.0 0.99-1.58 65-170
X - 10.0 0.85 100
X - 10.0 0.65 30
2)
Consumption
Litres kWh Minutes
3)
5019 496 90454
How to use the appliance
ABC
Further indications are given in the single chapters and in the user instructions.
Switch on the appliance
Select, save, and
supply the detergent
Check the rinse aid level
Check the
regeneration salt level
Load the racks
Press the ON / OFF button.
(The first time you use the appliance
and when using a different type of
detergent)
1. Select the third programme from the
top in the relative table.
2. Press the Start button for about 7
seconds until the display changes.
3. Select the required detergent with
the Start button (OFF = powder
detergent, 2 in 1, 3 in1, 4in1) (shown on the display).
4. Switch the appliance off and then switch it on again. The selected
detergent type will be shown on the display for approximately 3
seconds after switching on.
For dosage of powder detergent in compartment A and B refer to the
programmes table.
Mechanical indicator lamp C.
Electric indicator on control panel (if provided).
On models with water softener
system only.
Mechanical indicator lamp D. Electric
indicator on control panel (if provided).
Refer to the dishwasher loading instructions.
Close the dishwasher door,
turn on the water tap
Select a programme
Select additional options
Press the Start button
Wash cycle
Switch off the appliance
Turn off the water tap,
unload the racks
The last programme selected will light up.
Select the desired programme (using the specific button or knob).
The corresponding indicator lamp lights up.
If necessary (and if provided).
The corresponding indicator lamp lights up.
The selected programme is
then memorised (even in the
event of power failure).
Only after the START button has switched off: Press the ON /
All the indicator lamps switch off.
Warning: When the door is opened steam comes out!
Unload the appliance, starting from the lower rack.
“Change programme in progress”
Press the START button for 2 sec. until the
Start indicator lamp switches off.
Select another programme and press the
START button again.
- Only open the dishwasher if necessary
(Warning: beware of hot steam).
- I f the appliance is switched off during a
wash cycle, when switched on again it
will resume the cycle from where it was
interrupted.
OFF
button.
Loading...