Bauknecht GSI 5240 DI BR, GSI 5240 DI IN Quick Reference Guide

Quick reference guide
Chart
BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ
THIS QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS!
(see at right for options description)
PROGRAMS SELECTION BUTTON
Push “Programs” button (repeatedly) until the indicator of the required program lights up (see “Table of programs” below).
START/RESUME BUTTON
Push this button to start the selected program: the indicator lights up and goes off at the end of the program. When the door is opened during a washing cycle, the cycle is temporarily paused: the Start indicator blinks. To resume the cycle close the door and push Start button again.
Ta b l e o f p r o g r a m s
CANCEL/OFF BUTTON
Push this button to switch off the control panel. If pressed when a program is running it cancels the program ongoing draining water for 1 minute (0:01 is shown into the display). If pressed when the dishwasher is switched off, it drains any possible liquids from dishwasher (1 minute process).
Consumption
Deter-
gent
Litres kWh
X 7-14 1.00-1.60 70-155
X 11.0 0.80 30
X 11.5 1.05 165
X 14.0 1.55 155
Minutes
50°C
Available
options
Delay
Multizone
Antibacterial
rinse
Delay
Multizone
Delay
Multizone
Delay
Multizone
Antibacterial
rinse
Delay
Multizone
Antibacterial
rinse
Loading instructions
Recommended programme for routine washes, with dried-on food (e.g. EN 50242).
Crockery to be washed later. 4.0 0.03 14
Lightly soiled crockery, with no dried-on food.
Normally soiled crockery. Energy-saving program.
Recommended program for heavily soiled crockery, especially suitable for pans and saucepans.
P
1
2
3
4
5
1) Program data obtained in conformity with European standard EN 50242, obtained under normal conditions (without additional options) and may vary depending on conditions. Differences of up to 20 minutes are possible with sensor programs as a result of the appliance’s automatic calibration system.
2) Reference program for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information on the EN/Standard loading comparison test and other tests, contact the following address: “nk_customer@whirlpool.com”.
3) The antibacterial action has been tested by the Institut Pasteur of Lille (France), based on the NF EN 13697 standard of November 2001.
Programs
AutoSensor 50-65°C
Pre-Wash cold
Quickwash 45°C
Bio Normal
2)
Intensive 70°C
THE CONTROL PANEL OF THIS DISHWASHER ACTIVATES PUSHING
ANY BUTTON EXCEPT CANCEL/OFF BUTTON.
FOR ENERGY SAVING THE CONTROL PANEL DEACTIVATES
AUTOMATICALLY AFTER 30 SECONDS IF NO CYCLE HAS STARTED.
Options and display description
SALT INDICATOR
When lit (at the end of the cycle), the salt reservoir needs to be refilled.
WASH TIME DISPLAY
Indicated the cycle duration and the remaining time (h:min). With “Delayed start” selected it indicates the time remaining until program start (h.00) - below 1h (0:min). If “Fx Ey” messages appears on the display, see page 6 - chapter “What to do if...”.
MULTIZONE
Allows you to choose the washing
1)
zones. Press this button (repeatedly) to select the wash zones:
both racks
only lower rack
only upper rack
- indicator lits
ANTIBACTERIAL RINSE
This function activates an antibacterial rinse at the end of the wash cycle, guaranteeing a further reduction of bacteria. Press the button to activate or deactivate the function. This function can be used with the programs indicated in the table of programs. The dishwasher door must be kept shut for the entire duration of the program in order to guarantee reduction of bacteria. If the door is opened the indicator lamp starts flashing.
3)
TABLET SETTING
This setting allows to optimize the cycle performances according the type of detergent used. Push the Tablet button for 3 seconds (until the indicator lights up) if you are using the combined detergents in tablet (rinse aid, salt and detergent in 1 dose). If you are using powder detergent or liquid detergent, the Tablet indicator on the control panel has to be off.
RINSE AID INDICATOR
When lit (at the end of the cycle), the rinse aid dispenser needs to be refilled.
DELAYED START BUTTON
Push the button (repeatedly) to delay the start of the program. Adjustable from 1 to 24 hours. With each press of the button, the delayed start indicator increases by one hour and after 24 restarts from 0. Then press the START button. The dishwasher will start after the set time.
5019 496 01676GSI 5240 DI
GB
-1-
How to set water hardness in order to always assure the best cleaning results
First time use
1- salt reservoir 2- rinse aid dispenser 3- detergent dispenser 4- racks system 5,6,7,8- available functions on the panel 9- filters 10- spray arms
Water hardness should be set only
before the first wash or if water
hardness has been changed
Water hardness level is factory set for medium-hard water (level 4).
Even if you use tablets which include salt functionality, you must still add regeneration salt since such detergents are not effective enough at softening hard water.
At first time use, the salt reservoir has to be filled independently from water hardness level (see description below in step 1 “Daily check”).
Filling the salt reservoir -
1
The salt level indicator lamp may remain lit at the end of several wash cycles. If the water hardness level falls within category (soft), no salt is required.
-Press and hold together Programs and CANCEL/Off buttons for minimum 3 seconds.
- The current water hardness setting will be visible on the display.
-Press the
- Wait 30 seconds (control panel switches off) or press Start/Resume button to save setting.
1.
degrees °dH
Programs
the start button will set the level back to 1).
Ask your water supply company what the
German
0 - 5 0 - 9 0 - 6.3 Soft 1
6 - 10 10 - 18 7 - 12.6 Medium 2 11 - 15 19 - 27 13.3 - 18.9 Average 3 16 - 21 28 - 37 19.6 - 25.9 Medium-hard 4 22 - 28 38 - 50 26.6 - 35 Hard 5 29 - 35 51 - 63 35.7 - 44.1 Very hard 6 36 - 50 64 - 90 44.8 - 62.4 Extremely hard 7
button to increase setting. Value range goes from 1 to 7 (when the level reaches 7, the next press of
French
degrees °fH
English
degrees °eH
water hardness
Water hardness
level
is...
2.
...enter this value on your dishwasher
Insert value is shown
Dissolve limescale (not necessary if water hardness level is set to “soft”!)
Visual indicator (depending on the model). Unscrew cap.
Fill the salt reservoir with water
before the first wash only.
(depending on the model)
Salt indicator on the control panel Salt indicator on the salt reservoir cap
The indicator lamp lights up when SALT NEEDS TO BE ADDED.
Add salt (never add detergent!)
min. 0.8 kg / max. 1 kg
in the display
Suggestions for detergent use
Gel or Powder
(rinse aid and salt)
go to step 1
(see “Daily
check”)
green: OK.
Tab l et s
if water is
HARD extra salt
needs to be added
(go to step 1,
“Daily check”)
Daily check
Screw on the cap. Salt residual around the cap need to be removed. Some salt reservoir have a level indicator integrated in the cap (see below how to check).
clear: NEEDS TO
BE ADDED
GB
-2-
Adding rinse aid
(not necessary when you use tablets). How to adjust the rinse aid dosage regulator
Daily check
Visual
2
Check the rinse aid indicator to check the level into the dispenser.
Only use rinse aids recommended for use in domestic dishwashers. Immediately wipe away any rinse aid spilt accidentally. This prevents the formation of excess suds which can cause a fault function of the appliance.
If there are streaks: reduce the dosage by turning the dial to a lower setting (1-3). If crockery is not perfectly dry: increase the dosage by turning the dial to a higher setting (5-6). Plastic dishes have more difficulty drying and a higher rinse aid setting will not improve the situation.
Detergents with rinse aid incorporated may be effective only with longer programs. In the case of shorter programs, detergent residue may be a problem (if necessary, use powder detergent). Detergents with rinse aid incorporated tend to form excess suds.
Adding detergent -
(press the dedicated button).
Use only detergent specifically for dishwashers in accordance with the supplier’s recommendations
Open the cover A
3
indicator
If required, open the cover B (press the dedicated button).
Add rinse aid to the max. line ~150 ml
(depending on the model)
Rinse aid indicator on the control panel Rinse aid indicator on the dispenser
The indicator lamp lights up when RINSE AID NEEDS TO BE ADDED.
Insert detergent: Tablet / powder / liquid into the big chamber
Only fill the detergent dispenser prior to starting a wash program.
The rinse aid dosage can be adjusted to the detergent used. The lower the setting, the less rinse aid is dispensed (factory setting: position 4). Press the button to open the cover B. Using a coin or similar object, turn the arrow to the desired setting. After adjusting the rinse aid setting, shut the cover again.
dark: OK. clear: NEEDS TO BE ADDED
Shut the cover
by pressing dedicated ribs.
Use only one tablet per one cycle, only placed in detergent dispenser.
All types of tablets can be used, but for 2 in 1 type adding of salt is mandatory.
Daily use
GB
-3-
Loading...
+ 5 hidden pages