Bauknecht GSI 4896 TW-WS, GSI 4896 TW-SP, GSI 4896 TW-IN, GSI 4896 TW-SW Quick Reference Guide
GB
DYNAMIC SENSE: Energy savings and optimum wash results
The two sensor-controlled “DYNAMIC SENSE” wash options are
recommended for routine washes. They use double-sensor
technology. Separate sensors gauge turbid ity an d pa rticle s in o rder to
determine the degree of soiling of the wash w ater. In accordance with
values measured, a microprocessor establishes optimum water,
energy and time consumption. Optimum wash results are thus
achieved using only those resources strictly required.
GSI 4896
Further indications are given in the pages to follow and in the user instructions.
Water supply indicator
Check the appliance fills with water.
spray arm block indicator
Lower
Release the spray arm.
“Water stop” device indicator
“Water stop” device not working. Switch
off the dishwasher and shut off the water tap.
Rinse aid level indicator
Add rinse aid.
Salt level indicator
Add regeneration salt; only add regeneration
salt immediately before starting a wash
programme.
Programme Symbol
and Temperature
Eco Normal 40 - 55° C
Intensive 60 - 70° C
Pre-wash
Recommended programme
with little or no dried-on food.
Recommended programme
dried-on food. Especially suitable for pans and saucepans.
Crockery to be washed later.
Programme selection and
recommended load type
Programme progress indicator
Pre-rinse /
Pre-wash
Washing
Half Load button
This function can be used with any
programme. The indicator lamp switches
on: the wash cycle is activated for the
upper or lower rack
for heavily soiled crockery
Quick Reference Guide
Drying
Programme end
Options
.
only
Place the detergent in the:
compartment compartment
for routine washes
, for crockery
, with
Delayed start buttons
The wash cycle can be programmed to start after 1-24 hours.
Then press the Start button. The dishwasher will start at the set time.
Time and failure display
Indicates in hours the time remaining until the start of the wash cycle.
Switches off when the programme has started.
Toward the end of the programme, during the drying cycle,
the display will indicate the time remaining in minutes.
“F1--F9” Identification of faults for service technician.
Start button
Indicator lamp lit while the dishwasher is oper ating. Flashes when
a fault occurs. Switches off at the end of the programme.
On / Off Button
small large
(Litres)
X X
X X
- - 5.0 (4.2) 0.02 (0.02) 9(9)
Consumption
Normal load / (Half load)
Water
Energy
(kWh)
(13.5)
(11.5)
(19.5)
(11.5)
1)
Time
(Min.)
(1.3)
(0.9)
(1.7)
(1.3)
(80)
(60)
(98)
(90)
Rapid 40° C
Glasses 40° C
Bio-Normal 50° C
1) Values may vary in relation to usage, e.g.: different loads, water
temperatures - above or below 15° C - as well as water hardness and power supply voltage etc.
2) Reference programme for Test Institute and energy-label.
Lightly soiled crockery with no dried-on food.
Light soiling, especially glasses and cups.
2)
Normally or heavily soiled crockery with dried-on food.
- X 13.0 (13.0) 0.85 (0.75) 30 (30)
- X 12.0 (10.0) 0.82 (0.78) 60 (59)
X X 16.0 (14.5) 1.03 (0.90) 120 (117)
5019 100 90322
(We reserve the right to make technical modifications)
A
A
C
B C
How to use the dishwasher
1. After loading the dishwasher, close the
door properly and open the water
supply tap.
2. Press the On/Off button to switch the
dishwasher on.
indicator lamps will switch on.
3. Select the desired programme by
pressing the corresponding button.
The corresponding indicator lamp
lights up.
supplied).
4. Press the Start button to start the
selected programme.
indicator lamp will light up.
the programmed data cannot be
altered by pressing the programme
selector buttons.
once the Start button has been
Note:
pressed, the dishwasher memorises the
last programme selected. This
information remains in the memory even
during interruption of the power supply.
To change the selected
programme, press the Start button
for about 5 seconds
Start indicator lamp switches
off.
press the Start button.
if the dishwasher is switched
Note:
off during a wash programme,
when switched on again it will
resume the wash cycle from
where it was interrupted.
Only open the dishwasher door
if strictly necessary during a
wash cycle and exercise
maximum caution. Danger of
scalding from steam.
5. To indicate the end of the programme,
the Start indicator lamp switches off
and
the End indicator lamp (if fitted)
lights up
One of the programme
If required, select options (if
The Start
Once set,
, until the
Select a new programme and
(for about 30 min.)
.
6. Once the Start indicator lamp has
switched off press the On/Off bu tton to
switch the dishwasher off.
indicator lamps switch off.
7. Open the door (warning: beware of hot
steam). Unload the lower rack before
the upper one. Close the water tap.
All the
Upper rack
B
Half Load:
If the upper rack
the cutlery basket
Rack height adjustment:
(The dishwasher is delivered with the
upper rack in the top position).
The rack height can also be chan ged
when loaded.
is to be loaded, place
only
in the upper rack.
“B”
Upper and lower rack
• To lower: pull out the
handles and gently lower the rack.
• To raise: pull up the
until the rack clicks into place.
• The rack must be level on both sides.
Crockery holders:
• Down: cups and long-stemmed glasses.
•
Up: plates.
“Vario Organizer” multi-purpose
support:
• To be used, for example, for longhandled utensils
with the blade facing downwards),
cups and glasses.
• May be used in three different
positions (see also “Dishwasher
loading instructions” on Page 4).
1. Upon the left-hand side of the rack.
2. Upside-down, towards the centre of
the rack.
3. Upside-down, towards the left side.
(arrange knives
Glass holder:
side
two
side handles
two
Lower rack
Half Load:
Loading the lower rack
greater washing power, especially for
plates and saucepans.
Plate holders:
• May be lowered to increase
available space (A).
only
gives
A
Cutlery basket:
The cutlery basket (
removed to increase available space.
B + C
) can be
Please read the user instructions carefully.
Loading...