Before using the dishwasher, read the user instructions!
ADP 6830
Indicators
Quick Reference Guide
Programme selection button
On / Off button
Start button
Switches “on” when the dishwasher is
operating. Flashes when a fault occurs.
Switches off at the end of the programme.
Add regeneration salt
Only add regeneration salt immediately
before starting a wash programme.
Add rinse aid
Options
GB
Time and failure display
Indicates in hours the time remaining until the start
of the wash cycle. Switches off when the
programme starts and indicates the time remaining
in hours and minutes.
“F... .” Identification of faults for service technician
“Delayed start” button
The wash cycle can be programmed to start after
1 - 24 hours. With each successive touch of the button,
the delayed start indicator increases by 1 hour , and
after 24 returns to 00. Then press the Start button.
The dishwasher will start at the set time.
Antibacterial rinse
This function adds an antibacterial rins e at th e end o f
the wash cycle, thereby guaranteeing a perfectly clean
and sanitized load. The lamp will light up when the
function is activated. If the tempe rat ur e is n ot
maintained during the antibacterial cycle (e.g. if the
door is opened and remains open for a long time), the
lamp will start blinking to indicate that sa ni tat ion is
not guaranteed.
“Half Load” button
The half load cycle can be used for the upper and
lower rack. Select the required programme then
press the “Half Load” button. The light comes on
and goes off at the end of the programme.
The “Half Load” function can be used with
programmes marked with an *.
3)
4)
Programme chart
Detergent
ProgrammesLoading instructionsAB
Sensor Normal
Sensor Intensive
5) (*)
5)
40-55°C
60-70°C
Pre-Rinsecold
Glass40°C
Quickwash40°C
1) 5) (*)
Normal
1)Reference programme for energy label in compliance with EN
50242 regulations;
2)Refer to “User instructions”;
3)Program data obtained in conformity with European standard
EN 50242. Values may vary in relation to usage, e.g.: different
loads, water temperatures - above or below 15°C - as well as
water hardness and power supply voltage, etc.
Important information for Test Laboratories:
For detailed information on the EN comparison test and other tests, contact the following address: “nk_customer@whirlpool.com”.
Whirlpool is a registered trademark of Whirlpool USA
Automatic programme recommended
for routine washes, with no dried-on or
burnt food (not for EN 50242).
Automatic programme recommended
for heavily soiled crockery with dried-on
or burnt food, for example pans and
saucepans.
Crockery to be washed later.--5.00.0210
Light soiling, for example glasses and
cups.
Lightly soiled crockery with no
dried-on food.
Normally soiled crockery.XX16.01.05160
50°C
4)The bacteria removal efficiency has been tested by the Institut
Pasteur de Lille (France), based on the NF
EN 13697 standard of November 2001.
5)These programmes can be used with the Antibacterial rinse
option.
(We reserve the right to make technical modifications)
XX13.0-16.0 0.80-1.05 50-120
XX16.0-23.0 1.10-2.00 90-140
X-13.00.9055
X-13.00.7030
2)
Consumption
LitreskWh Minutes
5019 396 91517
3)
WH/I/B/GB
Page 2
How to use the appliance
Further indications are given in the single chapters and in the user instructions.
Switch on the appliance
Fill the detergent dispenser
Check the rinse aid level
Check the
regeneration salt level
Load the racks
Close the dishwasher door,
turn on the water tap
Select a programme
Press the ON / OFF button.
Compartment
With each wash cycle.
Compartment
For programmes with pre-wash only.
Mechanical indicator lamp C.
Electric indicator on control panel (if provided).
On models with water softener
system only.
Mechanical indicator lamp D. Electric
indicator on control panel (if provided).
Refer to the dishwasher loading instructions.
The last programme selected will light up.
Select the desired programme (using the specific button or knob).
The corresponding indicator lamp lights up.
A:
ABC
B:
Select additional options
Press the Start button
Wash cycle
Switch off the appliance
Turn off the water tap,
unload the racks
If necessary (and if provided).
The corresponding indicator lamp lights up.
The selected programme is
then memorised (even in the
event of power failure).
Only after the START button has switched off: P ress the ON /
All the indicator lamps switch off.
Warning: When the door is opened steam comes out!
Unload the appliance, starting from the lower rack.
“Change programme in progress”
Press the START button for 2 sec. until the
Start indicator lamp switches off.
Select another programme and press the
START button again.
- Only open the dishwasher if necessary
(Warning: beware of hot steam).
- If the appliance is switched off during a
wash cycle, when switched on again it
will resume the cycle from where it was
interrupted.
OFF
button.
WH/II/B/GB
Page 3
Dishwasher loading instructions and racks provided
depending on the model
Upper rack:
Crockery holder (A):
Depending on the position, for long-handles utensils,
cups and plates.
Glass holder (B):
Long-stemmed glasses.
Long-handled utensils (e.g. carving forks, knives)
must be arranged with the sharp end facing in
towards the appliance.
Half Load:
Load the upper rack
if provided, in the upper rack.
only
. Place the cutlery basket (C),
Rack height adjustment (also when loaded):
two
Lower adjustment:
Upper adjustment:
The rack must be level on both sides.
Removing the top rack to provide clearance for
large items of crockery in the bottom rack:
Open the rack guide retainers (E) on the right and left
and remove the top rack.
When the upper rack is in place the retainers must
always be closed.
Pull the
(D) outwards and lower
the rack.
Pull the
(D) upwards until the rack
clicks into place (factory
setting).
rack handles
two
rack handles
B
A
C
D
D
Retainer
open
E
Retainer
closed
E
Lower rack:
Depending on the model
with fixed or tilting plate
holders (F).
Half Load:
Load the lower rack
Greater washing power,
particularly for plates and
saucepans.
only
.
F
F
Cutlery basket (G):
Grid (H) to keep items separate.
Sharp knives and forks that might cause injury
must be placed in the cutlery basket with the
sharp end facing downwards.
Only use dishwasher-proof crockery and dishes. Do not use the appliance for items not suitable for
washing in a dishwasher, for example wooden items, aluminium, tin, hand-decorated crockery
(unglazed), silver cutlery.
H
G
C
WH/III/GB
Page 4
What to do if...
If a fault occurs, before contacting our After-Sales Service, make the following checks to try and remedy the problem (* see
also the corresponding chapter in the user instructions).
ProblemCauseRemedy
The appliance is not
working
If crockery is not
perfectly dry
If crockery is not
perfectly clean
Sandy or grainy
residues
Colour of plastic parts
faded
• No water supply.•Open the tap.
• The appliance does not load sufficient
water.
• There is a power failure.• Insert the plug into the mains socket.
• Starting the selected programme.• The programme can be set to “0” to start.
• Insufficient rinse aid.•Increase dosage *.
• Residual water in cavities.• Load crockery at an angle.
• Filters incorrectly assembled.• Insert the filter correctly *.
• T omato/carrot juice, ...• Depending on the material, if necessary use a
• Clean the water supply tap filter.
• Ensure there are no kinks in the water hose.
• Press the Start button.
•Close the door.
• Check the safety circuit breaker.
• Arrange crockery so that items do not touch each
other. Load crockery upside down.
detergent with a greater whitening power.
Deposits on crockery
•Removable• Streaks on the crockery/glasses.• Increase the rinse aid dosage *.
•Streaks on glasses.• Reduce the rinse aid dosage *.
• Layer of salt on crockery/glasses.• Close the salt container lid properly *.
•Not removable• Insufficient water softening, calcium
Opaque glasses/ glasses
deposits.
• Cannot be washed in the dishwasher.• Use suitable glasses.
• Change water hardness setting, if necessary add salt *.
not sparkling
Rust on cutlery
Identifying appliance
faults
If after carrying out the above checks the malfunction persists or appears again, turn the appliance off and turn off the water
supply tap, then call our After-Sales Service (see guarantee).
Before contacting our After-Sales Service, take note of the following:
• The nature of the fault
• The appliance type and model
• The service code (the number indicated on the adhesive rating plate)
inside the door on the right-hand side.
• Not made of stainless steel.• Use suitable cutlery.
• The START indicator lamp flashes.• Ensure the filter assembly is not clogged and that
there is no interruption to the water supply
(if necessary, clean the filters *). Start the programme
again. Press the START button for 2 seconds, until the
START indicator lamp switches off. Select a new
programme and press the Start button again.
• Indicator F... (if provided).• Contact the After-Sales Service.
WH/IV/GB
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.