BARCO AMM240ED User Manual

AUTO - SCANNING WITH DIGITAL CONTROL
LCD COLOR MEDICAL MONITOR

AMM240ED

Operation Manual

For future reference, record the serial number of your display
monitor in the space below :

Serial Number

The serial number is located on the back of the monitor

Back of the Monitor

The title «WARNING» is used to inform the users of pos-

sible causes that could inict the injury, death, or property

damage to the patients.

The title «CAUTION» is used to inform the users of pos-

sible causes that could inict the patients although it might

not severe enough to cause death.

AMM240ED 1

WARNING

CAUTION

NOTE

The title «NOTE» is used to inform the users of items that
are of importance in terms of installation, operation, or
maintenance of the Equipment although the failure does

not inict the bodily harm to the patients.

Barco, Inc. 2017

All other trademarks are the property of their reference owners.
This document is subject to change without notice.
BARCO provides this information as reference only. Reference to other vendor’s
products does not imply any recommendation or endorsement.

Revision Control

Document number I-101117190001

Rev. A

2 User’s Guide

Table of Contents

Product Description and Intended Use ......................................................

Warnings and Cautions .............................................................................

Symbol Denitions .....................................................................................

EU Declaration of Conformity for Medical Applications .............................

Safety Precaution ......................................................................................

Cleaning the Monitor .................................................................................

Recommendation to Use more than One Unit...........................................

On Burn-in .................................................................................................

Power Management Function....................................................................

Preset Modes..............................................................................................

Video Signals .............................................................................................

PIP / POP / PBP function...........................................................................

DDC ...........................................................................................................

Installation .................................................................................................

Connecting the Power Cord ......................................................................

User Function / Messages.........................................................................

OSD Section ..............................................................................................

Troubleshooting .........................................................................................

Specications of (AMM240ED)..................................................................

Classication .............................................................................................

Electromagnetic Compatibility ...................................................................

Dimension Drawing (mm) of AC Adapter ...................................................

Dimension Drawing (mm) of AMM240ED ..................................................

Connectors ................................................................................................

Description of Warranty .............................................................................

3

4

7
8
9
9

9
9

10

11

12

13

14
14

15
16
17

25
26
27
28

30
31

32
34

AMM240ED 3

Product Description and Intended Use

Please check the following items are present when you unpack the box, and save
the packing materials in case you will need to ship or transport the monitor in future.

• AMM240ED LCD Monitor (the equipment that displays information, graphic
data, image and video on the LED screen) and two video cables
(1) BNC x4 to HD15 Cable(1) DVI-I cable

• AC Power cord*

• AC-Adapter

CAUTION
Model No :BM060S24F06
(Bridgepower)

• BNC Cable, and Y/C Cable.

• DC extension cable (optional)

15ft length: Model 1501047***(Bridgepower)
75ft length: Model 1501047***(Bridgepower)
***: blank or 001~999

• CD Multi-language Manual, English User Manual and 4pcs VESA screws

• Cable Cover

• Stand (optional)

33-329-085, SB-004W

*Might vary pending on region standard

4 User’s Guide

Warnings and Cautions

Please read this manual and follow its instructions carefully. The words warning,
caution, and note carry special meanings and should be carefully reviewed:

Warning The personal safety of the patient or physician may be
involved. Disregarding this information could result in
injury to the patient or physician.

Caution Special service procedures or precautions must be
followed to avoid damaging the instrument.

Note Special information to make maintenance easier or important

information more clear.

An exclamation mark within a triangle is intended to alert the

user to the presence of important operating and maintenance
instructions in the literature accompanying the product.

A lightning bolt within a triangle is intended to warn of the
presence of hazardous voltage. Refer all service to authorized

personnel.

Warning TO AVOID POTENTIAL SERIOUS INJURY TO THE USER

AND THE PATIENT AND/OR DAMAGE TO THIS DEVICE,
THE USER MUST :

Warranty is void if any of these warnings are disregarded.

Barco, Inc. accepts full responsibility for the effects on safety, reliability, and
performance of the equipment only if:

• Re-adjustments, modications, and/or repairs are carried out exclusively

by Barco, Inc.

• The electrical installation of the relevant operating room complies with the
applicable IEC and CE requirements.

Warning Federal law (United States of America) restricts this
device to use by, or on order of a physician.

The Barco, Inc. AMM240ED monitor has been tested under UL (ANSI/AAMI ES
60601-1) standard and UL listed for Medical application.

Barco, Inc. reserves the right to make improvements in the product(s) described
herein. Product(s), therefore, may not agree in detail to the published design
or specications. All specications are subject to change without notice. Please

contact Barco, Inc. directly or phone your local Barco, Inc. sales representative or
agent for information on changes and new products.

AMM240ED 5

Warnings

1. Read the operating manual thoroughly and be familiar with its contents prior to using
this equipment.

2. Carefully unpack the unit and check if any damage occurred during shipment.

3. Should any solid object or liquid fall into the panel, unplug the unit and have it checked

by qualied personnel before operating it any further.

4. Uplug the unit if it is not to be used for an extended period of time. To disconnect the

cord, pull it out by the plug. Never pull the cord itself.

5. Be a qualied physician, having complete knowledge of the use of this equipment.

6. Test this equipment prior to a medical procedure. This monitor was fully tested at the
factory before shipment.

7. Avoid removing covers on control unit to avoid electric shock.

8. Attempt no internal repairs or adjustments not specically detailed in this operating

manual.

9. Pay close attention to the care, cleaning instructions in this manual. A deviation may

cause damage (refer to the Cleaning section).

10. DO NOT STERILIZE MONITOR.

11. Read the entire instruction manual before assembling or connecting the camera.

12. Do not place the monitor or any other heavy object on the power cord. Damage to the
cable can cause re or electirc shock.

13. Monitor with power supply is suitable for use in patient environment.

14. DO NOT stack more than 3 boxes high

15. To avoid the risk of electric shock, this equipment must only be connected to a supply
mains with protective earth.

This equipment has been tested and found to comply with the limits for medical devices in

IEC 60601-1-2:2014. These limits are designed to provide reasonable protection against

harmful interference in a typical medical installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to other devic-

es in the vicinity. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to other devices, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

- Reorient or relocate the receiving device.

- Increase the separation between the equipment.

- Connect the equipment into an outlet on a circuit different from that to which the other

device(s) are connected.

- Consult the manufacturer or eld service technician for help.

NOTICES TO USER

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any inter-

ference received, including interference that may cause undesired operation.

FCC WARNING

This equipement generates or uses radio frequency energy. Changes or modications not

expressly approved by the party responsible for compliance could void the user’s authority
to operate the equipment. The user could lose the authority to operate this equipment if an

unauthorized change or modication is made.

6 User’s Guide

Cautions

1. The AC Adapter must be plugged into a Grounded power outlet.

2. Use only the proprietary AMM240ED power supply for the
AMM240ED monitor. Make a proper connection by ensuring that the

shrink tubing completely secures the connection between the DC power cord and the
extension cord.

3. Turn power off when unit is not in use.

4. Never operate the unit right after having transported from a cold location directly to a

warm location.

5. Do not expose the monitor to moisture or directly apply liquid cleaners directly to the
screen. Spray the cleaning solution into a soft cloth and clean gently.

6. Handle the monitor with care. Do not strike or scratch the screen.

7. Do not block the monitor cooling vents. The monitor is cooled by natural convection
and has no fan.

8. Do not force the monitor past 28 degrees of vertical when adjusting the screen
position. (For monitors equipped with stands only.)

9. Remove the power module and connection when transporting the unit.

10. Save the original carton and associated packing material. They will be useful should
you have to transport or ship the unit.

11. Allow adequate air circulation to prevent internal heat buildup.

12. Do not place the unit on surfaces (rugs, blankets, etc.) or near materials (curtains,
draperies) that may block the ventilation slots.

13. Do not install the unit near sunlight, excessive dust, mechanical vibration or shock.

14. The unit is designed for operation in a horizontal position. Never operate the unit in

a vertical position.

15. Keep the unit away from equipment with strong magnets (i.e. a large loudspeaker.)

16. Do not expose the monitor to moisture or excessive dust.

17. Equipment with SIP/SOP connectors should either comply with IEC 60601-1
harmonized national standard or the combination should be evaluated.
Do not touch the patient with signal input or output connectors.

18. Use only a hospital grade power supply cord.

19. This equipment has been tested and found to comply with the limit for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable generate uses and can radiate radio frequency energy, if not installed and
used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation, which can be detemined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following
measures:

• Reorient or relocate the receiving device.

• Increase the separation distance between the equipment.

• Connect the equipment to an outlet on a circuit different from that to which the

other device(s) are connected.

• Consult the manufacturer or eld service technican for help.

20. Grounding reliability can only be achieved when the equipment is connected to an

equipment receptacle labeled “Hospital Only” or “Hospital Grade.”

21. The products have lower breaking capacity type. So do not install at the building power

system prospective short-circuit current exceeding 35 A.

22. Disconnecting of the power cord from teh AC/DC Adapter is the proper means of isolation

from the supply mains.
Note To connect to an international power supply, use a an attachment plug

appropriate for the power outlet.

Note Refer to the “Electromagnetic Compatibility” (EMC) section of this manual to
ensure EMC. The AMM240ED must be installed and operated

according to the EMC information provided in this manual.

AMM240ED 7

Dangerous: High Voltage

Direct Current

Serial Number

This Way Up

Fragile, Handle with Care

Stacking Limit by Number

Keep Dry

Recyclable

See Accompanying Document

Indicates Protective Earth
Ground.

For Indoor Use Only.

Tested to Comply with FCC
Class B Standards.

Stand-by

Tested to Comply with Japan

Tested to Comply with China

BSMI Mark for Taiwan
Approval

Mark for CU Countries­Russia,Kazakhstan, Belarus

China RoHS symbol. Number
indicates EFUP(Environmental
Friendly Use Period) from the
date of manufacturing.

Indicates proof of confor­mity to applicable European
Economic Community Council
directives and to harmonized
standards published in the of-

Communities.

Authorized Representative in
Europe

Date of Manufacture

Manufacturer

Medical Equipment

Medical Equipment is in ac­cordance with ANSI/AAMI ES 60601-1
and CAN/CSA C22.2 No. 60601-1
in regards to electric shock,

hazards.

Tested to Comply with IP
(Ingression Protection) Rating

WEEE symbol for recyclable
product. Please do not throw
the product with this symbol in
the bin.

8 User’s Guide

EU Declaration of Conformity for Medical Applications

A Declaration of Conformity has been led for this product. A sample

of this document may be found in the addendum which accompanies
this manual. For a copy of the Declaration of Conformity document,

please contact Barco, Inc. and request the AMM240ED DOC.

Prepare to Unpack Monitor

Before you unpack your monitor, prepare a suitable workspace. You
need a stable and level surface near a grounded wall outlet in an area
which is relatively free of glare from sunlight or other sources of bright

light. The monitor is cooled by natural convection (it has no fan).

For optimum performance, do not block the cooling vents.

While unpacking the monitor, inspect it and other package contents
for shipping damage that could cause a re or shock hazard. Imme­diately report any shipping damage to the carrier or transportation
company and contact customer service for monitor in case of return.

After you unpack the monitor, make sure the following items are in­cluded

• Monitor with video cable

• AC adapter with cable

CAUTION: AC Adapter must be plugged into Grounded a power outlet

CAUTION : AC adapter
Model No: BM060S24F06 (Bridgepower)

• This operation manual

Note: Your system provider may offer alternative cords or cables
depending on the installation requirement and local geography issues.

AMM240ED 9

Safety Precaution

· Avoid placing the monitor, or any other heavy object, on the power cord

· Do not expose the monitor to rain, excessive moisture, or dust to avoid

· Do not cover the slots or openings of the monitor for proper heat

dissipation. Always put the monitor in a place where there is adequate
ventilation.

· Avoid placing the monitor against a bright background or where sunlight

. Place the

monitor just below eye level.

· Handle with care when transporting the monitor.

· Refrain from giving the shock or scratch to the screen, as screen is

fragile.

· Performance of preventive maintenance is not essential. Periodic maintenance

inspections are essential to keep the monitor in optimum condition and ensure
safe operation. We recommend a functional and safety test of the monitor at regular
intervals (e.g. at least once a year).

Cleaning the Monitor

However, we suggest to clean the monitor with non-abrasive cloths and cleaning
solutions used in hospitals to clean similar equipment. We recommend using 70%
isopropyl alcohol for the screen surface and warm water and a mild detergent for all
other surfaces. Other acceptable cleaning agents are listed below:

• 70% isopropyl alcohol

• Cidex (2.4% glutaraldehyde solution)

• 0.5% Chlorhexidine in 70% isopropyl alcohol

To clean the screen, do not spray liquid cleaners directly on to the unit. Stand away
from the monitor and spray cleaning solution onto a cloth. Without applying exces­sive pressure, clean the screen with the slightly dampened rag.

Recommendation to Use More Than One Unit

As unforeseen situations can occasionally occur for the monitor, when the display
is used please use a safety control. It is strongly recommended you use more than
one unit or prepare a spare unit in case there is an emergency.

On Burn-in

Permanent burn-in may occur from the following:

• Displaying color bar or static images repeatedly or for a long period of time.

• Using the unit repeatedly in a high temperature/ high humidity environment

• Displaying an image smaller than the monitor continuously.

To reduce the risk of burn- in, it is recommended to turn off the power of the unit,
and reduce the brightness when the unit is not in use.

10 User’s Guide

Power Management Function

The monitor is equipped with the power management function which automatically
reduces the power consumption when not in use in three power level modes.

• Stand-by Mode

The monitor goes into stand-by mode when the horizontal sync signal is off for

about 10 seconds. In this mode, the screen goes off and the power LED blinks

for 1 second On and 1 second Off. The screen is displayed after the horizontal
sync signal is restored.

•Suspend Mode

The monitor goes into suspend mode when the vertical sync signal is off for
about 10 seconds. The power consumption during this is 10 W. In this mode,

the screen goes off and the power LED blinks for 1 second On and 1 second

Off. The screen is displayed after the vertical sync signal is restored.

• Off Mode

The monitor goes into power-off mode when the vertical and horizontal sync
signals are off for about 10 seconds. In this mode, the screen goes off and the

power LED blinks for 1 second On and 1 second Off. The screen is displayed

after the vertical and horizontal sync signals are restored.

Power Management System

The AMM240ED Medical Monitor power management proposal provides four

phases of power saving modes by detecting the horizontal sync signal as shown in
the table below.

State

Horizontal Sync Active Inactive Active Inactive

Vertical Sync Active Active Inactive Inactive

Video Active Blanked Blanked Blanked

Power Indicator Green

Power
Consumption

Normal
Operation

40W 15W 15W 15W

DPMS
Standby

Green Flashing (1
sec. Interval)

DPMS
Suspend

Green Flashing (1
sec. Interval)

DPMS Off

Green Flashing (1
sec. Interval)

When the monitor is power saving mode or detects an incorrect timing, the screen

will be blank and power LED indicator will blink.

PRESET MODES

Input Signal Timing

AMM240ED 11

Horizontal

Resolution

640 x 350 @70Hz 31.469 70.087 25.175

640 x 480 @60Hz 31.469 59.940 25.175

640 x 480 @75Hz 37.500 75.000 31.500

800 x 600 @56Hz 35.156 56.250 36.000

800 x 600 @60Hz 37.879 60.317 40.000

800 x 600 @75Hz 46.875 75.000 49.500

1024 x 768 @60Hz 48.363 60.004 65.000

1024 x 768 @70Hz 56.476 70.069 75.000

1024 x 768 @75Hz 60.023 75.029 78.750

1152 x 864 @60Hz 54.348 60.053 80.000

1152 x 864 @70Hz 63.955 70.016 94.200

1152 x 864 @75Hz 67.500 75.000 108.000

frequency

( KHz )

Vertical

frequency

( Hz )

Pixel clock

( MHz )

1280 x 1024 @60Hz 63.981 60.02 108.000

1680 x 1050 @60Hz 64.742 59.946 119.125

1680 x 1050 @60Hz 65.160 59.944 147.000

1600 x 1200 @60Hz 74.077 59.981 130.375

1920 x 1080@60Hz 67.500 60.00 148.500

1920 x 1200@60Hz 74.099 59.999 154.125

12 User’s Guide

Video Signals

Format DVI-I HD-15 Y/C SDI1 SDI2

Component/RGBs

Y/Pb/Pr/

RGB+SOG

RGB+
CS

NTSC-M

NTSC-443

PAL-BDGHI
PAL-M
PAL-N
PAL-60

480/59.94i O O O O

480/59.94p O O

576/50i O O O O

576/50p O O O O

720/50p O O O O O O

720/59.94p O O O O O O

720/60p O O O O O O

1080/23.98p O O O O O

1080/24p O O O O O

1080/25p O O O O O O

1080/29.97p O O O O O O

O

O

1080/30p O O O O O O

1080/50i O O O O O

1080/59.94i O O O O O

1080/60i O O O O O

1080/50p O O

1080/60P O O

PIP / POP / PBP Function*

The following combination options are available to you:

AMM240ED 13

PIP
Main

DVI-I X O X O O O

SDI 1 O X O O O X

SDI 2
(Optional)

Component/
RGBs

HD-15 O O O X X O

Y/C O X X O O X

*When the frame frequency of the main screen is different from that of the sub screen, the picture may
be disturbed.

*When both main and sub screens input interlace signals, the picture may be disturbed.

DVI-I SDI1

X O X O O O

O O O X X O

SDI2

(Optional)

Component /

RGBs

HD-15 Y/C

14 User’s Guide

DDC

To make your installation easier, the monitor is able to Plug and Play with your

system if your system also supports DDC protocol. The DDC (Display Data
Channel) is a communication protocol through which the monitor automatically

informs the host system about its capabilities, for example, supported resolutions

and corresponding timing. The monitor supports DDC1 and DDC2B standard.

Installation

To install the monitor to your host system, please follow the steps as given below:

Steps

1. Use the supplied video cable (DVI-I, Y/C, BNC, BNCx4 to HD15) then connect to

the
host system accordingly.

2. Connect the DC power to the DC power connector on the monitor.

3. Connect one end of AC power cord into the AC Adapter and the other end to AC

power outlet.

4. Then turn the host system on and then the monitor.

5. If the monitor still does not function properly, please refer to the troubleshooting

section to diagnose the problem.

DC Power

HD/SD SDI1 OUT

HD/SD SDI1 IN

HD15/RGBS IN

RS232C

USB

DVI-I OUT

DVI-I IN

Y/C IN

HD/SD SDI2 IN

AMM240ED 15

Connecting the Power Cord

*

the area.

* This monitor has an universal AC adapter that allows operation in either

AC 100 - 240 V ac voltage area. No user-adjustment is required.

* Plug one end of the power cord to the AC adapter, plug another end to a proper

AC outlet.
The cord set should have the appropriate safety approvals for the country in which
the equipment will be installed and marked HAR.

For 120 volt Applications, use only the UL Listed detachable power cord with NEMA

(tandem blades) plug cap.

Hospital-grade
power cord

Extension power cord (optional)
15ft length: Model 1501047***(Bridgepower)
75ft length: Model 1501047***(Bridgepower)
***: blank or 001~999

Power Supply
Model No: BM060S24F06

AMM240ED

16 User’s Guide

User Functions / Messages

Key Name and Function

Power : Turns ON/OFF the system.
Menu : Enter /Exit OSD menu.

Left : Decrease setting/Value.

Right : Increase setting/value. Enter Sub menu
Up : Move to previos item.
Down : Move to next time.
Select : Select item.
Brightness : Quick key for brightness adjustment.
Contrast : Quick key for contrast adjustment.
Scale Mode : Quick key for scale mode adjustment
Input: Activate the video source selection menu.

Power Switch

How to Access the Menu.

1. Press the Menu button to activate the OSD menu.

2. Press the Up or Down button to select icons. The icon will be

highlighted when selected.

3. Press the right arrow button to go into another OSD menu.

4. Press the enter button to select sub menu and the right arrow or left arrow button

to select the function.

5. In order to exit from the OSD menu, choose the “Exit” icon. Press the menu but­ton, then it will completely exit from the menu regardless of where you are.

6. Press the input button to enter the input menu. Push the Up or Down arrow to
highlight the correct input and press enter to select the input.

OSD Section

Chromatic Adjust Color Temp, Gamma

AMM240ED 17

Main Menu

Visual Adjust Brightness, Contrast, Phase, Chroma,

Sharpness-V, Sharpness-H

Setting Adjust Scale Mode, Color Space, Freeze Frame,

Zoom / Pan, PIP, POP, PBP

Advanced Adjust OSD Position Control, Screen Control, DPMS, Auto

Source Select, Smart Select, Restore Factory, Key Lock,

Overscan

Information User Customer Entry, Serial Number, Runtime, Input Format,

Exit

18 User’s Guide

OSD Section

Chromatic

Color Temp Change the Color Temperature - D65, D93, SYS-1, SYS-2

Red 0~100

Green 0~100

Blue 0~100

Gamma Change the Gamma Value - 1.8, 1.9, 1.95, 2.1, 2.1S, 2.2, 2.3,

2.4, 2.4S, S0, Radiograph

Exit Exit the Menu

Visual

Brightness Adjust the Brightness of Panel (Range 0 - 100)

Contrast Adjust the Contrast of Video (Range 0 - 100)

Phase Adjust the Phase of Video (Range 0 - 100)

*Available for Y/C and HD/SD SDI1 only

Chroma Adjust the Chroma of Video (Range 0 - 100)

*Available for Y/C and HD/SD SDI1 only

Sharpness-V Set the Sharpness of Vertical Image (Range 0 - 20)

Sharpness-H Set the Sharpness of Horizontal Image (Range 0 - 20)

Exit Exit the Menu

OSD Section

Setting

Scale Mode Change the Scale Mode - Fill all, One to One,

Vertical - Fill, Horizontal - Fill, Fill aspect ratio

Color Space Change Color Space Between RGB and YUV

Freeze Frame Off / On Freeze Frame

Zoom / Pan Activate zoom/pan OSD

PIP Activate PIP Menu

AMM240ED 19

POP Activate POP Menu

PBP Activate PBP Menu

Exit Exit the Menu

20 User’s Guide

OSD Section

Sub menu of PIP

Mode PIP Mode ON / OFF

Source PIP Sub Screen Source - DVI-I, HD/SD SDI1, HD/SD SDI2

Component/RGBs, HD15, Y/C

Position PIP Sub Screen Position - Top L, Top R, Bottom L, Bottom R

Size PIP Sub Screen Size - Small, Medium, Large

Blending PIP Sub Screen Blending (Range 0 - 20)

Swap PIP Sub Screen Swap

Exit Exit the Menu

Sub menu of PBP

Mode PBP Mode ON / OFF

Source PBP Sub Screen Source - DVI-I, HD/SD SDI1, HD/SD SDI2

Component/RGBs, HD15, Y/C

Swap PBP Sub Screen Swap

Exit Exit the Menu

OSD Section

Sub menu of POP

Mode POP Mode ON / OFF

Source POP Sub Screen Source - DVI-I, HD/SD SDI1, HD/SD SDI2

Component/RGBs, HD15, Y/C

Position POP Sub Screen Position - Top L, Top R, Bottom L, Bottom R

Size POP Sub Screen Size - Small, Medium, Large

Blending POP Sub Screen Blending (Range 0 - 20)

AMM240ED 21

Swap POP Sub Screen Swap

Exit Exit the Menu

22 User’s Guide

OSD Section

Advanced

OSD Position Change the OSD Menu - H and V Position, Background,

Control OSD Time Out, Language

Screen Control Control and Adjust H and V position, Freqency, Phase,

Noise Reduction, Motion Offset

DPMS Change the DPMS - Off, 60 min, 90 min, 120 min, Normal

Auto Source

Select

Smart Select Enable / Disable Smart Select Sub Menu - Model A, Model B

Model C, Model D

Restore Factory Changes All OSD Value to Factory Outgoing Status

Key Lock Set to Key Lock Mode

Overscan Adjust Overscan Ratio - Off, Step 1, Step 2, Step 3, Step 4,

Step 5, Step 6, Step 7

Exit Exit the Menu

Adjust Auto Source Select Between On and Off

(associated with the Color Temperatures are factory calibrated
with a consequent reduction of the maximum luminance compared
to Native Color Temperature.)

OSD Section

Sub Menu of OSD Control

H-position Adjust OSD H - Position (Range 0 - 100)

V-position Adjust OSD V - Position (Range 0 - 100)

Back ground Adjust Transparency of OSD Background (Range 0 - 20)

OSD Timeout Adjust OSD timeout - 5s, 10s, 15s, 20s, 1m, 2m

Language OSD Language - English, Japanese, Chinese, Korean,

French, German

Exit Exit the Menu

AMM240ED 23

Sub menu of Screen Control

H-Position Adjust Screen H - Position (Range 0 - 100)

*Available for HD15, HD/SD SDI1 Component/RGBs

V-Position Adjust screen V - Position (Range 0 - 100)

*Available for HD15, HD/SD SDI1 Component/RGBs

Frequency Adjust Frequency (Range 0 - 100)

*Available for HD15

Phase Adjust Phase (Range 0 - 100)

*Available for HD15

Noise Noise Reduction (Range 0 - 31)

Reduction

Motion Offset Motion Offset (Range 0 - 100)

Exit Exit the Menu

24 User’s Guide

OSD Section

Information

Custom Entry Change the User or Monitor’s Name

Custom Entry Row 1, Custom Entry Row 2

SN Display the Serial Number

Runtime Display the Total Runtime

Input Format Display the Current input Resolution and Vertical Frequency

Exit Exit the Menu

AMM240ED 25

TROUBLESHOOTING

Before sending your LCD monitor for servicing, please check the troubleshooting

list below to see if you can self-diagnose the problem.

Problems Current Status Remedy

No Picture Power LED ON · Using OSD, adjust brightness and

Power LED OFF · Check the Standby Power Button and

Power LED Blinking · Check if video signal cable is properly

Abnormal Picture Unstable Picture · Check if the specication of graphics

Display is missing, center shift,
or too small or too large in
display size

contrast to maximum or reset to their
default settings.

Power switch.

· Check if AC power cord is properly
connected to the AC adapter.

connected at the back of monitor.

· Check if the power to computer system
is ON.

adapter and monitor is in compliance
which may be causing the input signal
frequency mismatch.

· Using the Screen Control Menu, adjust

the Phase, Frequency, Horizontal, and

Vertical settings in order to correct the
display image.

26 User’s Guide

Specication*

Model AMM240ED

Diagonal 24.07 inches (611.32) diagonal
Resolution 1920 (H) x 1200 (V) @ 60hz
Pixel Pitch 0.270mm x 0.270mm
Display Color 16.7M colors
Viewing Angle H: 178°, V: 178°
Brightness 300 cd/m² (typical)
Contrast ratio 1000:1 (typical)
Dimension 570 (W) x 386.8 (H) x 63.2 (D) mm
Color Gamut sRGB 100%

LCD Response Time 14msec (Typ.)

Input

BNC x 1

HD/SD SDI 1

HD15

Component/RGBs

Y/C

General

Power Adaptor

Power Consumption 40W
Package Dimension 665 x 240 x 640 (H)

Weight

VESA Mounting 75mm x 100mm

Operating/Storage Environment

Operating Tempera­ture

Operating Humidity 25% ~ 75%, non-condensing
Storage Temperature -0° ~ 140°F (-18° - 60°C)
Storage Humidity 15 ~ 90%RH (without condensation)

Compliance &Certication

Safety

EMC

Optional Module

DC Extension Cable 5ft, 15ft, 75ft length

Base Stand Adjustable high, swivel and tilt base stand

0.27~2.97Gb/s Serial input data
rate
500~1100mVp-p Serial input
swing

15p D-Sub (female)

Video: 0.7 ± 0.1 VP-p

H/V Sync: TTL Level (V high
≥2.3V, V low ≤0.5V)
Horizontal Frequency 30~80KHz
Vertical Frequency 50~85Hz

MAX. 162MHz Output
15p D-Sub (female) (BNCx4 to

HD15 Cable

RGB: 0.7 ± 0.1 Vp-p

Composite Sync : 0.3Vp-p ~ 5Vp-

p H/V SYNC : TTL Level
Mini Din 4-pin
NTSC, PAL Color standard TMDS Level

Luminance : 1.0± 0.1VP (Video
:0.7Vp-p / Sync : 0.3Vp-p) Chromi-

nance : 0.3 ± 0.03Vp-p

AC 100 ~ 240V 50-60Hz
DC 24V, 2.7A

Monitor : 7.35Kg (Without cable cover, Without stand)
AC adaptor : 410g

50° ~ 104°F (10° - 40°C)

UL(ANSI/AAMI ES 60601-1), cUL(CAN/CSA-C22.2 No. 60601-1), CE(EN 60601-1, IEC
60601-1), AS/NZS 3200-1-0, CCC(GB4943.1), CB-ITE (IEC 60950-1), IP22 Compliance

FCC(Part 15 Class B), CE(EN 60601-1-2, IEC 60601-1-2), AS/NZS 3200-1-2, VCCI(Class
B), CCC(GB9254, GB17625.1)

HD/SD SDI 2
(optional)

DVI-I

HD/SD SDI

DVI-I

BNC x 1

0.27~2.97Gb/s Serial input

data rate

720~880mVp-p Serial input

Voltage swing

DVI-I 24+5 pin (female)

TMDS Level

MAX. 162MHz

BNC x 1 ( 75 ohm ±5% )

0.27~2.98Gb/s Serial output

data rate
350~600mVp-p Serial output
swing

DVI-I 24+5 pin (female)

MAX. 162MHz

* All contents are subject to change without notice.

**Brightness shown is without touch screen or A/R lter installed.

AMM240ED 27

: Direct Current

MEDICAL EQUIPMENT

Medical Equipment

WITH RESPECT TO ELECTRIC SHOCK,
FIRE AND MECHANICAL HAZARDS ONLY
IN ACCORDANCE WITH
ANSI/AAMI ES 60601-1 and
CAN/CSA C22.2 No. 60601-1

: UL approval mark according to the
safety standard for Medical equipment

This monitor is intended for use in Health Care Facilities model AMM240ED

with air or with oxygen or nitrous oxide.

For disposal of waste product, follow the requirement of local code.

Electrical input rating: 24V DC 2.7A

Type of protection against electric shock: Class I Equipment.

Degree of protection against the ingress of water: IP22 compliance.

Mode of operation: Continuous

This monitor has been tested to comply with IEC/EN 60601-1, IEC/EN60601-1-2

, in ad-

dition to the medical requirements, has also been tested and found to comply with

system complies with applicable EMC laws.

Environmental conditions for transport and storage:

- Temperature range within -4° to 140° F (-20° to 60°C)

- Relative humidity range within 10% to 85%

- Atmospheric pressure range within 500 to 1060 hPa.

28 User’s Guide

Electromagnetic Compatibility

Like other electrical medical equipment, the AMM240ED requires special precautions
to ensure electromagnetic compatibility with other electrical medical devices. To ensure
electromagnetic compatibility (EMC), the AMM240ED must be installed and operated
according to the EMC information provided in this manual.

Note The AMM240ED has been designed and tested to comply with IEC 60601-1-

2:2014 requirements for EMC with other devices.

Caution Portable and mobile RF communications equipment may affect

the normal function of the AMM240ED.

Warning Do not use cables or accessories other than those provided
with the AMM240ED, as this may result in increased electromagnetic emis­sions or decreased immunity to such emissions.

Warning If the AMM240ED is used adjacent to or stacked with other

equipment, observe and verify normal operation of the AMM240ED in the

a

surgical procedure.

Consult the tables below for guidance in placing the AMM240ED.

Manufacturer’s declaration - electromagnetic emission

The customer or the user of AMM240ED should assure that it is used in such an environment.

Emission test Compliance Electromagnetic environment - guidance

RF emissions CISPR 11 Group 1

RF emissions CISPR 11 Class B

Harmonic emissions

IEC61000-3-2

Voltage Fluctuations

IEC61000-3-3

Class A

Complies

The Model AMM240ED uses RF energy only for its internal
function. Therefore, its RF emissions are very low and are not
likely to cause any interference in nearby electronic equipment

AMM240ED is suitable for use in all establishments, including
domestic establishments and those directly connected to the
public low-voltage power supply network that supplies buildings
used for domestic purposes

Manufacturer’s Declaration - Electromagnetic Immunity

The customer or the user of AMM240ED should assure that it is used in such an environment.

Immunity Test IEC 60601 Test Level Compliance Level

Electrostatic discharge
(ESD)
IEC61000-4-2

Electrical fast transient
/burst IEC61000-4-4

Surge
IEC61000-4-5

±
±

±

±

8 kV contact
2 kV, ± 4 kV, ± 8 kV, ± 15 kV air

2 kV

100 kHz repetition frequency

0,5 kV, ± 1 kV, ± 2 kV

Electromagnetic
environment - guidance

Floors should be wood,
concrete or ceramic tile.

synthetic material, the relative
humidity should be at least
30%.

Mains power quality
should be that of a typical
commercial or hospital
environment.

Mains power quality
should be that of a typical
commercial or hospital
environment.

AMM240ED 29

Power frequency

(50/60Hz) mag­netic eld
IEC 61000-4-8

Voltage dips, short
interruptions and
voltage variations on
power supply input

lines IEC61000-4-11

3.0 A/m

50 Hz or 60 Hz

0 %

U

; 0,5 cycle

T

At 0° . 45°, 90°, 135°, 180°, 225°, 270°, and 315°

0%

U

; 1 cycle

T

3.0 A/m

50 Hz or 60 Hz

and

70 %

U

; 25/30 cycles

t

Single phase: at 0°

0 %

U

; 250/300 cycle

t

q)

Power frequency mag-

netic elds should be

at levels characteristic
of a typical location in
a typical commercial or
hospital environment.

Mains power quaility
should be that of a typical
commercial or hospital
environment. If the user

of the AMM240ED image
intensier requires con-

tinued operation during
power mains interrup­tions, it is recommended

that the AMM240ED
image intensier be

powered from an uninter­ruptible power supply or
a battery.

Note: Ut is the A.C. mains voltage prior to application of the test level.

Manufacturer’s Declaration - Electromagnetic Immunity

The Model AMM240ED is intended for use in the electromagnetic environment specied below.

The customer or the user of AMM240ED should ensure that it is used in such an environment.

Immunity Test IEC 60601 Test Level Compliance Level

Conducted RF

IEC61000-4-6

Radiated RF

IEC 61000-4-3

3 V

0,15 MHz - 80 MHz

6V in ISM and amature
radio bands between 0,15

MHz and 80 Mhz

80 % AM at 1 kHz

10 V/m

80 MHz - 2,7 GHz

80% AM at 1 kHz

3 V

0,15 MHz - 80 MHz

6V in ISM and amature
radio bands between

0,15 MHz and 80 Mhz

80 % AM at 1 kHz

10 V/m

80 MHz - 2,7 GHz

80% AM at 1 kHz

Electromagnetic environment -

Portable and mobile RF communications
equipment should be used no closer to
any part of the AMM240ED, including
cables, than the recommended separation
distance calculated from the equation
applicable to the frequency of the
transmitter.

Recommended Separation Distance

0.15 MHz to 80 MHz

guidance

80 MHz to 800 MHz

800 MHz to 2.5 GHz

where P is the maximum oputput power

rating of the transmitter in watts (W)

according to the transmitter manufacturer
and d is the recommended separation

distance in meters (m).

Field strengths from xed RF transmitters,

as deter-mined by an electromagnetic
site survey (a), should be less than the
compliance level in each frequency range
(b).Interferency may occur in the vicinity
of equipment marked with the follwing
symbol:

NOTE 1: At 80MHz and 800MHz, the higher frequency range applies.

NOTE 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and
reection from structures, objects, and people.

(a) Field strengths from xed transmitters, such as base stations for radio (cellular/cordless) telephones and land mo-

bile radios, amateur radio, AM and FM radio broadcast and TV broadcast, cannot be predicted theoretically with accu-

racy. To assess the electromagnetic environment due to xed RF transmitters, an electromagnetic site survey should
be considered. If the measured eld strength in the location in which the AMM240ED is used exceeds the applicable
RF compliance level above, the AMM240ED should be observed to verify normal operation. If abnormal performance is
observed, additional measures may be necessary, such as reorienting or relocating the AMM240ED.

(b) Over the frequency range 150kHz to 80MHz, eld strengths should be less than [V1] V/m.

30 User’s Guide

Recommended Separation Distances Between Portable and Mobile RF Communications Equi-

pement and the AMM240ED System

The AMM240ED system is intended for use in an electromagnetic environment in which radiated RF

disturbances are controlled. The user of the AMM240ED system can help prevent electromagnetic

interference by maintaining a minimum distance between portable and mobile RF communications

equipment (transmitters) and the AMM240ED system as recommended below, according to the maximum

Rated maximum output

power (W) of transmitter

0.01 0.12 0.12 0.23

0.1 0.37 0.37 0.74

1 1.17 1.17 2.33

10 3.70 3.70 7.37

100 11.70 11.70 23.30

For transmitters rated at a maximum output power not listed above, the recommended separation distance (d) in me-

ters (m) can be estimated using the equation applicable to the frequency of the transmitter, where P is the maximum

NOTE 1: At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.

NOTE 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and
reection from structures, objects, and people.

output power rating of the transmitter in watts (W) according to the transmitter manufacturer.

output power of the communications equipment.

Separation distance (m) according to frequency of transmitter

150kHz to 80MHz

d=1.17, p

80MHz to 800MHz

d=1.17, p

800MHz to 2.5GHz

d=2.33, p

Dimension Drawing (mm) of AC Adapter

Dimension Drawing (mm) of AMM240ED

AMM240ED 31

32 User’s Guide

Connectors

DC Input

Connector Jack Power Input

Pin Description Pin Description

1 GND 4 NC

2 GND 5 24V Input

3 24V Input

Video Input

24 Pin DVI-I In Connector.

DDWG or Equivalent Connector.

Pin Description Pin Description Pin Description

1 T.M.D.S. Data2- 9 T.M.D.S. Data1- 17 T.M.D.S. Data0-

2 T.M.D.S. Data2+ 10

3 T.M.D.S. Data2 Shield 11 T.M.D.S. Data1 Shield 19 T.M.D.S. Data0 Shield

4 NC 12 NC 20

5 NC 13 NC 21 NC

6 DDC Clock 14 +5V Power 22 T.M.D.S. Clock Shield

7 DDC Data 15 Ground (for +5V 23 T.M.D.S. Clock+

8 NC 16 Hot Plug Detect 24 T.M.D.S. Clock-

Video Input

24 Pin DVI-I Out Connector.

DDWG or Equivalent Connector.

T.M.D.S. Data1+

18 T.M.D.S. Data0+

NC

Pin Description Pin Description Pin Description

1 T.M.D.S. Data2- 9 T.M.D.S. Data1- 17 T.M.D.S. Data0-

2 T.M.D.S. Data2+ 10

3 T.M.D.S. Data2 Shield 11 T.M.D.S. Data1 Shield 19 T.M.D.S. Data0 Shield

4 NC 12 NC 20

5 NC 13 NC 21 NC

6 DDC Clock 14 +5V Power 22 T.M.D.S. Clock Shield

7 DDC Data 15 Ground (for +5V 23 T.M.D.S. Clock+

8 NC 16 Hot Plug Detect 24 T.M.D.S. Clock-

Video Input

HD/SD SDI1 IN Connector.

Pin Description Pin Description

1 SDI IN 2 GND

Video Input

HD/SD SDI1 Out Connector.

Pin Description Pin Description

1 SDI Out 2 GND

T.M.D.S. Data1+

18 T.M.D.S. Data0+

NC

Video Input

HD 15/RGBS IN Connector.

Pin Description Pin Description Pin Description

1 RED 6 GND-RED 11 GND

2 GREEN 7

3 BLUE 8 GND-BLUE 13 HSYNC(CS)

4 GND 9 G5V 14

5 GND 10 GND 15 DDC SCL

Signal Input

RS232C Signal Connector.

Pin Description Pin Description

1 NC 2 RX

3 TX 4 NC

5 GND 6 NC

7 NC 8 NC

9 NC

Signal Input

USB Signal Connector.

Pin Description Pin Description

1 Vcc(5V) 2 NC

3 NC 4 GND

GND-GREEN

AMM240ED 33

12 DDC SDA

VSYNC

Video Input

HD/SD SDI2 IN Video Connector.

Pin Description Pin Description

1 SDI Input 2 GND

Video Input

Y/C IN Video Connector.

Pin Description Pin Description

1 GND 2 GND

3 Chroma_In 4 Luma_In

34 User’s Guide

Description of Warranty

BARCO warrants to the rst Buyer (Buyer) that the product purchased when
shipped in its original container will conform to BARCO specications, and to any
BARCO approved specications furnished to BARCO by the Buyer, and will be

free of defects in materials and workmanship. BARCO warrants that the product
purchased is manufactured from new components which meet BARCO standards,

quality and specications.

Subject to the conditions and limitations set forth below, BARCO will, at its option,
either repair any component of its products that prove defective by reason of
improper workmanship or materials or BARCO has the exclusive right to replace
with refurbished units or with an equivalent product. BARCO warrants that the
components used for repair, refurbished units or equivalent product will meet

BARCO standards, quality and specications.

Commencement and Duration of Warranty

The product purchased will be warranted for a period of eighteen (18) months
(excluding the LCD panel, touch screen, and the protection lter) from the date of

shipment.

LCD panels and touch screens are warranted for a period of twelve (12) months

from the date of shipment.

Protection lters are not warranted as damage to the protection lter is considered

to be normal wear and tear and can be replaced at Buyer’s cost.

Components used for repair, refurbished units or equivalent product will be

warranted for a period of twelve (12) months from the date of repair.

Limitation of Warranty

This limited warranty does not cover any damage to this product or other non­BARCO products that results from any of the following: improper installation

or operation; accident; abuse; misuse; natural disaster; war; insufcient or

excessive electrical supply; abnormal mechanical or environmental conditions; any

unauthorized disassembly, repair or modication; normal wear and tear; tampering

by anyone other than an BARCO engineer or an BARCO Authorized Service Center

(ASC); the use of supplies, consumable items and conditions beyond the control of

BARCO, such as common carrier provided equipment and/or facilities; operation

of BARCO product in excess of the specications. This limited warranty also does

not apply to any product that has not been handled or packaged correctly, that has
been sold as second-hand or has been resold contrary to the US export regulations,

on which the original identication information (i.e. serial number, rating and/or
warranty label) has been altered, obliterated or removed.

AMM240ED 35

In Warranty

BARCO or its ASC will repair or replace if defective in material or workmanship

without cost, for a period of eighteen (18) months, (LCD panels and touch screens
for a period of twelve (12) months) after the date of shipment.

Buyer must notify BARCO or its ASC of the defect before expiration of the warranty

period, and request an RMA number. If the conguration has been modied in
any manner, the product must be returned to its original conguration before any

warranty service will be performed by BARCO or its ASC. No goods are to be
returned to BARCO or its ASC without prior authorization. Buyer will be responsible

for packaging (preferably original container) and shipping the defective goods to

BARCO or its ASC, shipping charges prepaid.

BARCO or its ASC will return the in warranty product, at no cost to the buyer.

36 User’s Guide
Out-of-Warranty

BARCO or its ASC will repair or replace if defective in material or workmanship with

fee, any product which the warranty period has expired (out-of-warranty).

Buyer must notify BARCO or its ASC of the defect and request an RMA number. If

the conguration has been modied in any manner, the product must be returned to
its original conguration before any service will be performed by BARCO or its ASC.

No goods are to be returned to BARCO or its ASC without prior authorization. Buyer

will be responsible for packaging (preferably original container) and shipping the

defective goods to BARCO or its ASC, shipping charges prepaid.

BARCO or its ASC will return the out-of-warranty product, at cost to the buyer.

Product End of Life (EOL)

In the event of an RMA of an EOL product(s), BARCO will hold or store major
components of its products for a period of ve (5) years, after the EOL of its

products. BARCO shall continue to perform the service of its products as long as
BARCO holds or stores said components of the products, with reasonable charge.

The forgoing Warranty and Out-of-Warranty terms apply.

AMM240ED 37

Disclaimer

THE FORGOING IS THE COMPLETE WARRANTY FOR BARCO PRODUCTS
AND SUPERSEDES ALL OTHER WARRANTIES AND REPRESENTATIONS,
WHETHER ORAL OR WRITTEN. EXCEPT AS EXPRESSLY SET FORTH ABOVE,
NO OTHER WARRANTIES ARE MADE WITH RESPECT TO BARCO PRODUCTS
AND BARCO EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED
HEREIN, INCLUDING, TO THE EXTENT PERMITTED BY APPLICABLE LAW, ANY
WARRANTY THAT MAY EXIST UNDER NATIONAL, STATE, PROVINCIAL OR
LOCAL LAW INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY ON
NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE. ALL WARRANTIES, WHETHER EXPRESS OR IMPLIED, ARE
LIMITED TO THE PERIODS OF TIME SET FORTH ABOVE. SOME STATES
OR OTHER JURISDICTIONS DO NOT ALLOW THE EXCLUSION OF IMPLIED
WARRANTIES OR LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY
LASTS, SO THE ABOVE LIMITATIONS MAY NOT APPLY.

BARCO’S TOTAL LIABILITY UNDER THIS OR ANY OTHER WARRANTY,
EXPRESSED OR IMPLIED, IS LIMITED TO REPAIR OR REPLACEMENT, AND
ARE THE SOLE AND EXCLUSIVE REMEDIES FOR BREACH OF WARRANTY
OR ANY OTHER LEGAL THEORY. TO THE FULLEST EXTENT PERMITTED
BY APPLICABLE LAW, BARCO SHALL NOT BE LIABLE TO THE PURCHASER

OR END USER CUSTOMER OF AN BARCO PRODUCT FOR ANY DAMAGES,

EXPENSES, LOST DATA, LOST REVENUES, LOST SAVINGS, LOST PROFITS,
OR ANY OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM
THE PURCHASE, USE OR INABILITY TO USE THE BARCO PRODUCT, EVEN
IF BARCO HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
SOME STATES OR OTHER JURISDICTIONS DO NOT ALLOW THE EXCLUSION
OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE
ABOVE LIMITATIONS MAY NOT APPLY.

THE LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU
MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE OR

JURISDICTION TO JURISDICTION.

Barco, Inc.

47817 Fremont Blvd. Fremont, CA 94538, USA
Tel : [phone]
Fax : [phone]