Barco 6400, 6500 User Manual

BARCO PROJECTION

ANALYZER KIT FOR G/R 6500/6400I AND

SIM6(HB) PROJECTORS

R817211K
R820349K
R821060K

INSTALLATION MANUAL

01122003 R5976207/02

Barco nv Intelligent Displays

aan 5, 8520 Kuurne

Noordl
Phone: [phone]
Fax: [phone]

[e-mail]

E-mail:
Visit us at the web: www.barco.com

Printed in Belgium

Copyright ©

All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be recorded, transmitted or
stored in a retrieval system without the prior written consent of BARCO.

Trademarks

Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights of their respective holders.
All brand and product names mentioned in this manual serve as comments or examples and are not to be understood as advertising for
the products or their man ufactures.

Table of contents

TABLE OF CONTENTS

1. Kit description ...................................................................................................... 3

1.1 Introduction............................................................................................................................. 3

1.2 Kit content.............................................................................................................................. 3

1.3 Domain of application.................................................................................................................. 4

2. Accessto the analyzers........................................................................................... 5

2.1 Removing the Top Cover .............................................................................................................. 5

2.2 Removing the EMC plat ............................................................................................................... 7

3. Replacing the Analyzer............................................................................................ 9

3.1 Removing the analyzers ............................................................................................................... 9

R5976207 ANALYZER KIT FOR G/R 6500/6400I AND SIM6(HB) PROJECTORS 01122003

1

Table of contents

2 R5976207 ANALYZER KIT FOR G/R 6500/6400I AND SIM6(HB) PROJECTORS 01122003

1. Kit description

1. KIT DESCRIPTION

1.1 Introduction

Analyzers in LCD projectors

Depending on the type of LCD projector the analyzers used may be different. The main differences resides in the mechanical
mounting system (way of mounting on the Xcube) and the material used, analyzers may be made of glass or saphir.

Image 1-1
analyzer type handled in this manual

Image 1-2
Mounting on the Xcube : fixation feet (image shows XCube assembly out of
the projector)

1.2 Kit content

Overview

One of the following kits can be ordered, each of them containing one analyzer.

Kitnumber Description

R817211K Red analyzer
R820349K
R821060K

Some projector (RST version) are equipped with adapted analyzers, please contact Barco for the right spare.

Always check the type of an alyzer and the type of projector and make sure to order the right analyzer.

Green analyzer (saphir)
Blue analyzer (saphir)

R5976207 ANALYZER KIT FOR G/R 6500/6400I AND SIM6(HB) PROJECTORS 01122003 3

1. Kit description

1.3 Domain of application

Overview

The analyzers handled in this manual are used in the following projectors.

Description Projector number

G6500 R9001950/R9001959
R6500
G6400i R9002840/R9002849
R6400i
RSIM6 HB
RSIM6 HB MLA

R9001960/R9001969

R9002800/R9002809
R9040120
R9040140

4 R5976207 ANALYZER KIT FOR G/R 6500/6400I AND SIM6(HB) PROJECTORS 01122003

2. Access to the analyzers

2. ACCESS TO THE ANALYZERS

Overview

• Removing the Top Cover

• Removing the EMC plat

Particularities

Depending on the projector the procedure to access the analyzers may be different.
In the RSIM6 projector the top cover can be removed without removing the lens whereas in the 6500/6400i projector the lens has

to be removed to allow cover removal.

In the images the cover colo r may not always coincide with the reality.

2.1 Removing the Top Cover

Location

The Top Cover is located on the Top side of the projector.

Image 2-1
Top Cover Location

Necessary Tool

• Flat blade screwdriver 8 mm.

Be sure the Projector Hand le is in the inserted position when removing the Top Cover.

How to remove the Top Cover

1. Remove the Lens Cover. (image 2-2)

2. Pull off the 3 rubber sealing pieces covering the Top Cover screws. (image 2-3)

Tip: Use th e flat blade screwdriver to pull off / slide in the tops of the 3 rubber pieces.

3. Turn out the 3 screws connecting the Top Cover to the Projector Frame. (image 2-4)

4. Remove the Top Cover.

5. Reverse this procedure to reinstall the Top Cover.

R5976207 ANALYZER KIT FOR G/R 6500/6400I AND SIM6(HB) PROJECTORS 01122003

5

2. Access to the analyzers

Image 2-2
Remove the Lens Cover

Image 2-3
Pull off the 3 rubber sealing pieces

Image 2-4
Turn out the 3 screw

s

6 R5976207 ANALYZER KIT FOR G/R 6500/6400I AND SIM6(HB) PROJECTORS 01122003

2.2 Removing the EMC plat

How to remove the EMC plate ?

1. Loosen the screw B retaining the electrical conductor. (image 2-5)

2. Turn out the screws A retaining the little plate

3. Remove the little plate

4. Turn carefully the remaining screws out. (imag e 2-6)

5. Remove the EMC plate

Image 2-5

2. Access to the analyzers

Image 2-6

be careful not to drop the screws into the projector.

R5976207 ANALYZER KIT FOR G/R 6500/6400I AND SIM6(HB) PROJECTORS 01122003 7

2. Access to the analyzers

8 R5976207 ANALYZER KIT FOR G/R 6500/6400I AND SIM6(HB) PROJECTORS 01122003

3. Replacing the Analyzer

3. REPLACING THE ANALYZER

3.1 Removing the analyzers

How to remove the analyzers ?

1. Remove the power cable (1) (image 3-1)

2. Remove the flat cables (2), disconnect by simultaneously pulling out the 2 mini locks on both sides of the flat cable connector.

Caution: Do not touch the contacts of the flat cable when removing the flat cable otherwise damage my occur by oxidation of

3. Loosen the 4 screws and remove the buffer module (image 3-2)

4. Loosen the 3 screws and remove the metallic plate (image 3-3)

5. Remove the analyzer sliding it gently out of the assembly. (image 3-4)

these contacts.
Do not use any tools when (dis)connecting a flat cable connector, otherwise damage may occur on the mini locks.

Image 3-1

Image 3-3

Image 3-2

R5976207 ANALYZER KIT FOR G/R 6500/6400I AND SIM6(HB) PROJECTORS 01122003 9

3. Replacing the Analyzer

Image 3-4
Removal of the analyzer

10 R5976207 ANALYZER KIT FOR G/R 6500/6400I AND SIM6(HB) PROJECTORS 01122003