Banner SPS101 DC Sensor Power Supply User Manual
SPS101 DC Sensor Power Supply
For Powering Banner dc Sensors
Printed in USA 04/02 P/N 66959 rev. B
SPS101 Features
• Converts 120V ac line voltage to low voltage dc for powering any Banner dc
sensor
†
which has either 4- or 5-pin Euro-style quick-disconnect (QD)
• SPS101 models: 5 amp-rated SPST relay for switching ac loads or large dc loads
• SPS101S models: optically-isolated SPST solid-state output for switching ac or dc
loads
•Models with “Q” suffix require a sensor with a pigtail QD connector; models with
“QP” suffix connect to a sensor with either an integral or pigtail quick-disconnect
• Isolated dc output
†
Note: SPS power supplies are not for use with NAMUR sensors or personal safety products.
SPS101QP
SPS101Q
105-130V ac
60 Hz
5-pin Euro-style QD*
5-pin Pigtail Euro-style QD
5-pin Mini QD
Model Supply Voltage Sensor Connection Supply/Output Cable
SPS101SQP
SPS101SQ
5-pin Euro-style QD*
5-pin Pigtail Euro-style QD
“Form A” (SPST) electromechanical relay
(see specifications for rating information)
Output Type
SPST Optically-isolated solid-state switch
(see specifications for rating information)
*Requires 4- or 5-pin Pigtail Euro QD on sensor.
SPS101 Sensor Power Supply Models
SPS101 Sensor Power Supply Dimensions
Model Suffix “QP”Model Suffix “Q”
Mini-Style Connector
“QD” Receptacle Pin Numbering
(Male Pins)
WARNING . . .
Not To Be Used for Personnel Protection
Never use these products as sensing devices for personnel protection. Doing so could lead to serious injury or death.
These sensors do NOT include the self-checking redundant circuitry necessary to allow their use in personnel safety applications. A sensor failure
or malfunction can cause either an energized or de-energized sensor output condition. Consult your current Banner Safety Products catalog for
safety products which meet OSHA, ANSI and IEC standards for personnel protection.
For sensors with
Euro-style
pigtail or
integral
QD
connector
For
sensors
with Euro-
style QD pigtail
only
1
2
3
4
5
Euro-Style Connector
“QD” Receptacle Pin Numbering
(Female Pins)
5-pin female Euro-style
QD connector
40.1 mm
(1.58")
48.8 mm
(1.92")
45.0 mm
(1.77")
64.5 mm
(2.54")
4.8 mm
(0.19")
89.9 mm
(3.54")
107.4 mm
(4.23")
132.5 mm
(5.20")
14 mm
(0.6")
Output Indicator
Pow
er
Indicator
ø 38.1 m
m
(1.50")
M5 (#10)
Screw Clearance (2)
Threaded Base M30 x 1.5
5-pin Mini-Style QD Connector
!
50.0 mm
(1.97")
4
1
5
3
2
5-pin female Euro-style
QD connector
500 mm (19.7")
pigtail cable
142.5 mm
(5.61")
SPS101 DC Sensor Power Supply
Banner Engineering Corp., 9714 Tenth Ave. No., Minneapolis, MN 55441 • Phone: 763.544.3164 • www.bannerengineering.com • Email: sensors@bannerengineering.com
Style Model Length
5-Pin
Mini-Style
Straight
MBCC-506
MBCC-512
MBCC-530
2 m (6.5')
4 m (12')
9 m (30')
Pin-Out (Female View)
WARRANTY: Banner Engineering Corp.
warrants its products to be free from defects
for one year. Banner Engineering Corp. will
repair or replace, free of charge, any product
of its manufacture found to be defective at
the time it is returned to the factory during
the warranty period. This warranty does not
cover damage or liability for the improper
application of Banner products. This
warranty is in lieu of any other warranty
either expressed or implied.
Quick-Disconnect Cables
SPS101 Sensor Power Supply Specifications
Output Power 120mA maximum: 12V dc minimum, 30V dc maximum (dependent on load)
Output Configuration
SPS101Q(P) models: “Form A” (SPST) electromechanical relay
SPS101SQ(P) models: Optically isolated SPST solid-state switch
Output Rating
NOTE: Output of the solid-
state models is not
short-circuit
protected. Exercise
care when making
wiring connections.
SPS101Q(P) models
Max. switching power (resistive load): 150 W, 600 VA
Max. switching voltage (resistive load): 250V ac or 30V dc (120V ac max. per UL & CSA)
Max. switching current (resistive load): 5A
Min. voltage and current: 1 amp at 5V dc, 0.1 amp at 24V dc
Peak switching voltage: 750V ac (transient suppression recommended)
Mechanical life of relay: 10,000,000 operations
SPS101SQ(P) models
Max. switching voltage: 250V ac or 250V dc
Max. switching current: 300 mA
On-state saturation voltage: less than 3V at 300 mA; less than 2V at 15 mA
Off-state leakage current: < 50 microamps
Inrush current: 1 amp for 20 milliseconds, non-repetitive
Connections Power connector: 5-pin Mini-style quick disconnect
Sensor connector:
“Q” version: 5-pin Euro-style quick-disconnect mounted on housing
“QP” version: Shielded, PVC jacketed 5-pin pigtail Euro-style quick-disconnect, 0.5 meter long
Environmental Rating IEC IP54
Operating Conditions Temperature: -20° to +50°C (-4° to 122°F)
Maximum Relative Humidity: 90% @ +50°C (non-condensing)
Additional Notes Compatible with Banner dc sensors with NPN or PNP output, equipped with 4- or 5-pin Euro-style quick-
disconnect (except NAMUR sensors). Minimum of 630V isolation from earth ground to dc output of circuit.
Supply Voltage 105V ac to 130V ac, 60Hz
Status Indicators Power On (green) and Output On (red)
SPS101 Sensor Power Supply Hookups
5
4
3
2
1
White
Brown
Yellow
Blue
Black
Euro-Style Connector
(to DC Sensor)
+
–
pin 1
pin 3
pin 2
pin 4
pin 5
DC
Voltage
No Connection
Sensor Output (NPN or PNP)
No Connection
AC to DC
Voltage
Converter
Output
Drive
Circuit
Mini-Style Connector
pin 4
pin 2
pin 1
pin 5
pin 3
105130V ac
Relay
Output
GND
(Earth Ground)
25
20
15
10
Output Voltage (V dc)
Voltage Regulation vs. Load
130V ac Input
115V ac Input
105V ac Input
20
040
Output Current Draw (milliamps)
60 80 100
Loading...