Model PPSIM..T
(Terminal strip connection)
Models PPSIM.. Sensor Interface Modules
DC-Powered Interface for PresencePLUS® P4 Sensors
Features
• Low-cost interface between user’s hardware and PresencePLUS P4 sensors
• Available with two methods for connecting to sensor, depending on model:
- 13-pin terminal strip for cordset with flying leads
- DB-15 connector for model P4C..SIM cordsets (see Cables on page 4)
• Available in current sinking (NPN) or current sourcing (PNP) output models
• LED indicators for sensor status and active outputs
• Integral External Trigger and Remote TEACH push buttons
• Easy-to-adjust 45° screw terminals for electrical wiring
• Built-in RS-232 serial port connector (DB-9, Female)
• Simple DIN-rail-mount or wall-mount configuration
Model PPSIM..C
(DB-15 connection)
Models
Models Output* Connections
PPSIM-NT
PPSIM-NC
PPSIM-PT
PPSIM-PC
P4 Sensor output must be set to NPN mode when used with an NPN interface module. P4
*NOTE:
Sensor output must be set to PNP mode when used with a PNP interface module. See the
System Setup window in the PresencePLUS GUI for output selections.
Current Sinking (NPN)
Current Sourcing (PNP)
Two 13-pin Terminals
One 13-pin Terminal
One DB-15 Connector
Two 13-pin Terminals
One 13-pin Terminal
One DB-15 Connector
Overview
The PPSIM.. series sensor interface module is a passive DIN-rail-mount or wall-mount
module. It enables remote external trigger and TEACH capability and provides remote
indication of sensor status for Banner PresencePLUS P4 Sensors.
Printed in USA 03/06 P/N 126330
Models PPSIM.. Sensor Interface Modules
Terminal Block (all models)
Power LED
External
Trigger LED
Remote
TEACH LED
DB-9
Connection
DB-15
Connection
(models
PPSIM..C only)
External
Trigger Push
Button
NOTE: Model PPSIM-PC shown. Models PPSIM..T have two terminal blocks and no DB-15 connection.
Figure 1. Features
Remote
TEACH
Push Button
I/O 1 through
I/O 4 LEDs
Installation
For mounting to a flat surface, unscrew one end cap, slide the DIN clips off of the housing,
and replace the end cap. Use the screw-holes in the end caps for mounting to a flat surface.
2 P/N 126330
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
Models PPSIM.. Sensor Interface Modules
Specifications
Input Supply Voltage
Adjustments
Indicator LEDs
Construction
Environmental Rating
Connections
Operating Conditions
Weight
10 - 30V dc (See PresencePLUS P4 specifications for sensor data)
External Trigger push button
Remote TEACH push button
NPN Models PNP Models
Power
Green: Power ON Red: Wrong polarity
External Trigger
Green: Active
Remote TEACH
Green: Active
I/O 1 through I/O 4
Green: Conducting
Power
Green: Power ON Red: Wrong polarity
External Trigger
Red: Active
Remote TEACH
Red: Active
I/O 1 through I/O 4
Red: Conducting
PCB circuit board; plastic housing, end caps, and DIN rail mounting hardware
IEC IP00: NEMA 1
Terminal Strip: Accepts 12 to 24 gauge wire
RS-232:
DB-9 female
PresencePLUS P4 Sensor (not included): DB-15 female, for SIM cordset (see Cables on page 4)
Temperature: 0° to +50° C (+32° to +122° F)
Max. Relative Humidity: 90% (non-condensing)
Approximately 135 grams (0.3 lb.)
Dimensions
2X 2.7 mm
(0.11")
2X 11.8 mm
(0.46")
127.5 mm (5.02")
137.6 mm
(5.42")
103.7 mm
(4.08")
49.5 mm
(1.95")
29.5 mm
(1.16")
2X R 2.7 mm
(R 0.11")
1
5
9
6
86.4 mm
(3.40")
43.2 mm
(1.70")
17.5 mm
(0.69")
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
P/N 126330 3
Models PPSIM.. Sensor Interface Modules
Terminal Block Wiring Table
The Terminal Block Wiring Table below is the same for all models.
Pin Color Description
Yellow RS-232 TX
1
Gray Remote TEACH
2
Orange Product Change
3
Pink External Trigger
4
Black I/O 1
5
Red I/O 2
6
White I/O 3
7
Light blue I/O 4
8
Violet RS-232 RX
9
Green
10
Blue
11
Brown 10-30V dc
12
13
Shield Drain
RS-232
(Signal Ground)
Common
(Signal Ground)
Cables (for use with PPSIM..C models)
Style Model Length
PresencePLUS P4 DB-15 SIM
Accessories
P4C06SIM
P4C23SIM
P4C32SIM
WARRANTY: Banner Engineering Corp. warrants its products to be free from defects for
one year. Banner Engineering Corp. will repair or replace, free of charge, any product of its
manufacture found to be defective at the time it is returned to the factory during the warranty
period. This warranty does not cover damage or liability for the improper application of
Banner products. This warranty is in lieu of any other warranty either expressed or implied.
2 m (6.5')
7 m (23')
10 m (32')
P/N 126330
Banner Engineering Corp., 9714 Tenth Ave. No., Minneapolis, MN USA 55441 • Phone: 763.544.3164 • www.bannerengineering.com • Email: sensors@bannerengineering.com
Loading...