Banner ECONO-BEAM SE61 User Manual

ECONO-BEAM®Sensors
Miniature Self-Contained DC Sensors
Printed in USA P/N 03410B0F
ECONO-BEAM Features
Small, low cost, self-contained sensors engineered to provide reliable sensing, primarily in straightforward OEM applications
Simple installation with no adjustments
Bipolar outputs (one NPN and one PNP); each output rated at 150 milliamps
Choose models for light operate or dark operate
Totally solid-state and epoxy-encapsulated for unlimited life
Very compact, yet rugged enough to withstand tough sensing environments; rated IP66, NEMA 4X
Infrared, 880 nm
ECONO-BEAM Opposed Mode Emitter (E) and Receiver (R)
Models* Range Cable
Supply
Voltage
Output
Type Excess Gain Beam Pattern
SE61E SE61R
1.8 m (6')
2 m (6.5') 10-30V dc
Bipolar
NPN/PNP
LO
*NOTES:
• 9 m (30')cables are available by adding suffix W/30to the model number of any cabled sensor (e.g., SE61RNC W/30).
• High-speed models may be ordered by adding suffixMHSto the model number of any standard ECONO-BEAM dc sensor (e.g., SE61EMHS). Response time for these sensors decreases to 1 millisecond; faster response comes at the expense of lower excess gain.
Bipolar
NPN/PNP
DO
SE61E SE61RNC
Due to their small size, right-angle design, and unique shape, this sensor pair is ideal for mounting against the side rails of conveyors for use in flow control and product sensing, and are an excellent choice for use on supermarket checkout stands. They may be bolted face-to-face to form a powerful slot sensor for edgeguiding of opaque materials or for sensing gear teeth, timing rings, or “flags,” with enough excess gain to operate even in the dirtiest sensing environments.
Effective Beam: 3 mm
1000
E X C
100
E S S
10
G A I N
1
0.01 m
0.033 ft
0.1 m
0.33 ft
DISTANCE
Opposed Mode
1 m
3.3 ft
10 m 33 ft
300 mm
Opposed Mode
200 mm 100 mm
0 100 mm 200 mm 300 mm
.6 m
0
2 ft
1.8 m
1.2 m 6 ft
4 ft
DISTANCE
2.4 m
12 in 8 in 4 in 0 4 in 8 in 12 in
3.0 m
8 ft
10 ft
page
2
ECONO-BEAM Sensors –
Miniature Self-Contained DC Sensors
ECONO-BEAM Non-Polarized Retroreflective Mode
Visible red, 650 nm
The 1/2" diameter effective beam of retroreflective model SE612LV, measured at 1' from the lens, makes it a good choice for sensing relatively small objects when opposed sensing is not possible. The visible beam simplifies alignment to the retroreflective target. Use the largest retroreflective target possible. If sensing materials with shiny surfaces, scan at an angle of at least 10° to the shiny surface to minimize false light return (“proxing” effect).
Ideal for applications where the target’s reflectivity and profile are sufficient to return a large percentage of the emitted light back to the sensor.Divergent diffuse model SE612W is particularly useful for sensing transparent or translucent objects (clear plastic or glass) and for dependable sensing of irregular surface features; its excess gain falls off sharply beyond 1". As a result, it may be used when it is necessary to ignore background objects.
Models* Range
Cable
Supply
Voltage
Output
Type Excess Gain Beam Pattern
SE612LV
4.5 m (15')
2 m (6.5') 10-30V dc
Bipolar
NPN/PNP
LO
SE612LVNC
Bipolar
NPN/PNP
DO
Infrared, 880 nm
ECONO-BEAM Diffuse Mode
200 mm
(8")
2 m (6.5')
Models* Range Cable
Supply
Voltage
Output
Type
Excess Gain Beam Pattern
10-30V dc
Bipolar
NPN/PNP
LO
SE612D
Bipolar
NPN/PNP
DO
SE612WNC
Bipolar
NPN/PNP
DO
Divergent Diffuse
Performance based on 90% reflectance white test card
SE612W
2 m (6.5') 10-30V dc
Bipolar
NPN/PNP
LO
76 mm
(3")
SE612DNC
Banner Engineering Corp. • Minneapolis, U.S.A.
Website: http://www.baneng.com • Tel: 888.373.6767
† Specified using model BRT-3 retroreflector (3" diameter). Actual range may vary depending on retroreflector size and efficiency.
1000
E X C
100
E S S
10
G A I N
1
0.01 m
0.033 ft
0.1 m
0.33 ft
DISTANCE
Retroreflective Mode With BRT-3 Reflector
1 m
3.3 ft
10 m 33 ft
150 mm 100 mm
50 mm
50 mm 100 mm 150 mm
Retroreflective Mode
0
0
.9 m 3 ft
With BRT-3 Reflector
1.8 m 6 ft
DISTANCE
2.7 m 9 ft
3.6 m 12 ft
4.5 m 15 ft
6 in 4in 2 in 0 2 in 4 in 6 in
1000
E X C
100
E S S
10
G A I N
1
1.0 mm
0.04 in
1000
E X C
100
E S S
10
G A
I
N
1
0.1 mm
0.004 in
10 mm
0.4 in
DISTANCE
1 mm
0.04 in
DISTANCE
Diffuse Mode
100 mm
4.0 in
Divergent Mode
10 mm
0.4 in
1000 mm
40 in
100 mm
4 in
7.5 mm
5.0 mm
2.5 mm
2.5 mm
5.0 mm
7.5 mm
22.5 mm 15 mm
7.5 mm
7.5 mm 15 mm
22.5 mm
Diffuse Mode
0
0
Divergent Mode
0
0
50 mm
2.0 in
25 mm
1.0 in
100 mm
4.0 in
DISTANCE
50 mm
2.0 in
DISTANCE
150 mm
6.0 in
75 mm
3.0 in
200 mm
8.0 in
100 mm
4.0 in
250 mm
10.0 in
125 mm
5.0 in
0.3 in
0.2 in
0.1 in 0
0.1 in
0.2 in
0.3 in
0.9 in
0.6 in
0.3 in 0
0.3 in
0.6 in
0.9 in
page 3
ECONO-BEAM Sensors –
Miniature Self-Contained DC Sensors
Banner Engineering Corp.
Minneapolis, U.S.A.
Website: http://www.baneng.com • Tel: 888.373.6767
Mechanical convergent-beam sensor’s light source and receiver opto-elements are positioned in the housing so that sensing takes place where the optical patterns cross. The sensing beam is intense at the
0.5" convergent point, excellent for sensing materials of low reflectivity and very small targets such as wire or thread; also effective for reflective sensing in areas where background suppression is a requirement. Visible red models are useful in some high-contrast color registration applications.
*NOTES:
• 9 m (30')cables are available by adding suffix W/30to the model number of any cabled sensor (e.g., SE612C W/30).
• High-speed models may be ordered by adding suffixMHSto the model number of any standard ECONO-BEAM dc sensor (e.g., SE612CMHS). Response time for these sensors decreases to 1 millisecond; faster response comes at the expense of lower excess gain.
Infrared, 940 nm Visible red, 650 nm
ECONO-BEAM Convergent Mode
Models* Focus Cable
Supply
Voltage
Output
Type
Excess Gain Beam Pattern
SE612C
12 mm
(0.5")
2 m (6.5') 10-30V dc
Bipolar
NPN/PNP
LO
Mechanical Convergent Mode; Infrared 940 nm
SE612CNC
Bipolar
NPN/PNP
DO
SE612CVNC
Bipolar
NPN/PNP
DO
Convergent Mode; Visible Red 650 nm
Performance based on 90% reflectance white test card
SE612CV
2 m (6.5') 10-30V dc
Bipolar
NPN/PNP
LO
16 mm
(0.65")
Spot Size at Focus:
1.2 mm (0.05")
1000
E X C
100
E S S
10
G A I N
1
0.1 mm
1 mm
0.004 in
0.04 in
1000
E X C
100
E S S
10
G A I N
1
0.1 mm
1 mm
0.004 in
0.04 in
DISTANCE
DISTANCE
SE612C
Convergent Mode
10 mm
0.4 in
SE612CV
Convergent Mode
10 mm
0.4 in
100 mm
100 mm
4 in
15 mm 10 mm
5 mm
0
5 mm 10 mm 15 mm
3 mm 2 mm 1 mm
1 mm 2 mm 3 mm
0
Convergent Mode
0
0
4 in
SE612C
Convergent Mode
15 mm
0.6 in
SE612CV
15 mm
7.5 mm
0.3 in
30 mm
1.2 in
DISTANCE
0.6 in
DISTANCE
45 mm
1.8 in
22.5 mm
0.9 in
60 mm
2.4 in
30 mm
1.2 in
75 mm
3.0 in
37.5 mm
1.5 in
0.6 in
0.4 in
0.2 in 0
0.2 in
0.4 in
0.6 in
0.12 in
0.08 in
0.04 in 0
0.04 in
0.08 in
0.12 in
ECONO-BEAM Sensors –
Miniature Self-Contained DC Sensors
page
4
Banner Engineering Corp. • Minneapolis, U.S.A.
Website: http://www.baneng.com • Tel: 888.373.6767
Diffuse mode performance based on 90% reflectance white test card
SE612FNC
Models*
Range
Cable
Supply
Voltage
Output
Type
Excess Gain Beam Pattern
SE612F
Range
varies by
sensing
mode
and fiber
optics
used
2 m (6.5') 10-30V dc
Bipolar
NPN/PNP
LO
Bipolar
NPN/PNP
DO
*NOTES:
• 9 m (30')cables are available by adding suffix W/30to the model number of any cabled sensor (e.g., SE612F W/30).
• High-speed models may be ordered by adding suffixMHSto the model number of any standard ECONO-BEAM dc sensor (e.g., SE612FMHS). Response time for these sensors decreases to 1 millisecond; faster response comes at the expense of lower excess gain.
Infrared, 880 nm
ECONO-BEAM Glass Fiber Optic
Ideal for situations where hostile environments or space restrictions prohibit placing the sensor itself in the sensing position. The response time required by model SE612F is 10 milliseconds (0.01 seconds). If fast-moving objects are to be detected, select a fiber optic assembly which senses the object for a long period of time. (For example, a bifurcated fiber optic with a rectangular bundle termination like model BR2.53S may be positioned so that the object is detected while it passes along the entire length of the rectangular sensing area.) Not recommended for applications requiring bending or repeated flexing of fibers.
1000
E X C
100
E S S
10
G A I N
1
1 mm
10 mm
0.04 in
0.4 in
1000
E X C
100
E S S
10
G A
I
BT13S Fiber
N
1
1 mm
10 mm
.04 in
IT13S Fibers
DISTANCE
BT23S Fiber
.4 in
DISTANCE
SE612F
Opposed Mode
IT23S Fibers
100 mm
4 in
SE612F
Diffuse Mode Glass Fibers
100 mm
4 in
1000 mm
40 in
1000 mm
40 in
75 mm 50 mm 25 mm
25 mm 50 mm 75 mm
1.9 mm
1.3 mm
0.65 mm
0.65 mm
1.3 mm
1.9 mm
0
0
0
0
SE612F
Opposed Mode
100 mm
7.5 mm
IT13S IT23S
200 mm
8 in
4 in
DISTANCE
SE612F
Diffuse Mode
15 mm
0.6 in
0.3 in
DISTANCE
300 mm
12 in
22.5 mm
0.9 in
400 mm
16 in
BT23SBT13S
30 mm
1.2 in
500 mm
20 in
37.5 mm
1.5 in
3 in 2 in 1 in 0 1 in 2 in 3 in
0.075 in
0.050 in
0.025 in 0
0.025 in
0.050 in
0.075 in
page 5
ECONO-BEAM Sensors –
Miniature Self-Contained DC Sensors
Banner Engineering Corp.
Minneapolis, U.S.A.
Website: http://www.baneng.com • Tel: 888.373.6767
Visible red, 650 nm
An excellent option where sensing must be accomplished in tight, inaccessible or volatile areas. Fibers withstand vibration and shock and are immune to electrical noise. Plastic fibers function well at temperatures between -30° and +70°C (-20°F to +158°F), and stand up to repeated flexing. Most are easy to shorten in the field, to develop custom installations. Not recommended for severe environments.
*NOTES:
• 9 m (30')cables are available by adding suffix W/30to the model number of any cabled sensor (e.g., SE612FP W/30).
• High-speed models may be ordered by adding suffixMHSto the model number of any standard ECONO-BEAM dc sensor (e.g.,
SE612FPMHS). Response time for these sensors decreases to 1 millisecond; faster response comes at the expense of lower excess gain.
ECONO-BEAM Plastic Fiber Optic
Diffuse mode performance based on 90% reflectance white test card
Models* Range
SE612FPNC
SE612FP
Range
varies by
sensing
mode and
fiber
optics
used
2 m (6.5') 10-30V dc
Bipolar
NPN/PNP
LO
Cable
Supply
Voltage
Bipolar
NPN/PNP
DO
Output
Type
Excess Gain Beam Pattern
1000
E X C
100
E S S
10
G A
I
PIT26U Fibers
N
1
1 mm
10 mm
0.04 in
0.4 in
1000
E X C
100
E S S
10
G A
I
N
1
0.1 mm
1 mm
0.004 in
0.04 in
DISTANCE
PBT26U Fiber
DISTANCE
SE612FP
Opposed Mode
Plastic Fibers
PIT46U Fibers
100 mm
4 in
SE612FP
Diffuse Mode
Plastic Fibers
PBT46U Fiber
10 mm
0.4 in
1000 mm
40 in
100 mm
4 in
45 mm 30 mm 15 mm
15 mm 30 mm 45 mm
3.6 mm
2.4 mm
1.2 mm
1.2 mm
2.4 mm
3.6 mm
0
0
0
0
SE612FP
Opposed Mode
Plastic Fibers
25 mm
1 in
PBT26U
7.5 mm .3 in
50 mm
2 in
DISTANCE
15 mm
.6 in
DISTANCE
75 mm
3 in
PBT46U
22.5 mm .9 in
PIT46UPIT26U
100 mm
4 in
SE612FP
Diffuse Mode Plastic Fibers
30 mm
1.2 in
125 mm
5 in
37.5 mm
1.5 in
1.8 in
1.2 in .6 in 0 .6 in
1.2 in
1.8 in
.15 in .10 in .05 in 0 .05 in .10 in .15 in
ECONO-BEAM Sensors –
Miniature Self-Contained DC Sensors
page
6
Banner Engineering Corp. • Minneapolis, U.S.A.
Website: http://www.baneng.com • Tel: 888.373.6767
Certifications
Supply Voltage and Current 10 to 30V dc (10% maximum ripple) at less than 20 mA (exclusive of load)
Supply Protection Circuitry Protected against reverse polarity and transient voltages
Output Configuration Bipolar: One current sourcing (PNP) and one current sinking (NPN) open-collector transistor Output Rating 150 mA maximum each output
Off-state leakage current less than 1 microamp Output saturation voltage (PNP output) less than 1 volt at 10 mA and less than 2 volts at 150 mA
Output saturation voltage (NPN output) less than 200 millivolts at 10 mA and less than 1 volt at 150 mA Output Protection Circuitry Protected against false pulse on power-up Output Response Time Less than 10 milliseconds ON and OFF; independent of signal strength
(NOTE: 100 millisecond delay on power-up: outputs do not conduct during this time.)
MHS Models: 1 millisecond (Faster response comes at the expense of lower excess gain.) Repeatability 0.4 ms; MHS models 0.06 ms; independent of signal strength.
Indicators All models except emitter-only units have a top-mounted LED indicator that lights whenever the receiver
“sees” its modulated light source. Construction Reinforced thermoplastic polyester (models LV, CV, F and FP) or polycarbonate (other models) housing,
totally encapsulated for protection against moisture, vibration and corrosion.
Environmental Rating Meets NEMA standards 1, 3, 3S, 4, 4X, 12, and 13; IEC IP66 Connections PVC-jacketed 4-wire 2 m (6.5') or 9 m (30') cables
Operating Conditions Temperature: 0° to +50°C (+32° to 122°F)
Maximum relative humidity: 90% at 50°C (non-condensing)
All Sensors Except Emitters
bn
wh
bu
+
bk
Load
Load
10-30V dc
ECONO-BEAM DC Hookups
SE61E Emitters
bn
bu
+
10-30V dc
ECONO-BEAM DC Specifications
page 7
ECONO-BEAM Sensors –
Miniature Self-Contained DC Sensors
Banner Engineering Corp.
Minneapolis, U.S.A.
Website: http://www.baneng.com • Tel: 888.373.6767
ECONO-BEAM DC Dimensions
Diffuse & Divergent Mode
(model suffix D & W)
Glass Fiber Optic (model suffix F)
Retroreflective & Convergent Mode
(model suffix LV & CV)
Mechanical Convergent Mode
(model suffix C)
Plastic Fiber Optic
(model suffix FP)
Opposed Mode
(model suffix E & R)
LED Indicator (Receiver Only)
13.7 mm (0.54")
6.4 mm (0.25")
19.1 mm (0.75")
5.1 mm (0.20")
3.1 mm (0.12")
12.7 mm
(0.50")
M3.5 (#6) Screw Clearance (2)
2 m (6.5') Cable
9.7 mm (0.38")
12.7 mm (0.50")
31.8 mm (1.25")
38.1 mm (1.50")
LED Indicator
16.5 mm (0.65")
12.7 mm (0.50")
10.2 mm (0.40")
15.2 mm (0.60")
14.4 mm (0.56")
M18 x 1 x 15 mm Thread (Mounting Nut Supplied)
22.9 mm (0.90")
15.2 mm (0.60")
6.1 mm (0.24")
30.0 mm (1.18")
6.4 mm (0.25")
13.0 mm (0.51")
38.6 mm (1.52")
24.9 mm (0.98")
14.4 mm (0.56")
14.4 mm (0.56")
33.0 mm (1.33")
Fiber Mounting Port
0.187" Dia. (2)
11.9 mm (0.47")
Banner Engineering Corp., 9714 Tenth Ave. No., Minneapolis, MN 55441 • Phone: 888.373.6767 • www.baneng.com • E-mail: sensors@baneng.com
ECONO-BEAM Sensors –
Miniature Self-Contained DC Sensors
WARNING . . .
Not To Be Used for Personnel Protection
Never use these products as sensing devices for personnel protection. Doing so could lead to serious injury or death.
These sensors do NOT include the self-checking redundant circuitry necessary to allow their use in personnel safety applications. A sensor failure or malfunction can cause either an energized or de-energized sensor output condition. Consult your current Banner Safety Products catalog for safety products which meet OSHA, ANSI and IEC standards for personnel protection.
WARRANTY: Banner Engineering Corp. warrants its products to be free from defects for one year. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture found to be defective at the time it is returned to the factory during the warranty period. This warranty does not cover damage or liability for the improper application of Banner products. This warranty is in lieu of any other warranty either expressed or implied.
Retroreflective Targets
65°C (150°F) 65°C (150°F)BRT-2A
Model
Reflectivity
Factor
Maximum
Temperature
BRT-3* 1.0
1.0
84 mm diameter
65°C (150°F)BRT-50 1.0
56 mm diameter
65°C (150°F) 65°C (150°F)BRT-1
BRT-1.5 1.0
1.0
Size
51 mm diameter
65°C (150°F)BRT-.6 1.0
46 mm diameter
65°C (150°F)BRT-50D* 1.0
25 mm diameter
50°C (120°F) 50°C (120°F)BRT-92X92C*
BRT-100X55A
50°C (120°F) 50°C (120°F)BRT-50R*
BRT-42D 1.0
1.0
20 mm diameter 51 mm diameter
50°C (120°F)BRT-25R 1.0
132 mm x 55 mm
50°C (120°F)BRT-42A 1.0
100 mm x 100 mm
1.5
3.0
42 mm diameter 51 mm diameter
50°C (120°F)BRT-77X77C* 2.0
25 mm diameter
50°C (120°F)BRT-100X50 1.5
42 mm diameter
50°C (120°F) 50°C (120°F)BRT-36X40BM
BRT-2X2 1.0
1.2**
85 mm x 85 mm 101 mm x 51 mm
50°C (120°F)BRT-60X40C* 1.4
51 mm x 61 mm
50°C (120°F)BRT-48X32 1.0
51 mm x 61 mm
50°C (120°F) 50°C (120°F)BRT-48X32B
BRT-48X32A 1.0
1.0
41 mm x 60 mm 33 mm x 48 mm
50°C (120°F)BRT-40X23 1.4
33 mm x 65 mm
50°C (120°F)BRT-40X23B 1.4
33 mm x 57 mm
50°C (120°F) 50°C (120°F)BRT-40X18A
BRT-35X20A 1.4
1.0
24 mm x 40 mm 24 mm x 48 mm
50°C (120°F)BRT-53X19A 1.4
24 mm x 55 mm
50°C (120°F)BRT-100X18A 1.4
18 mm x 60 mm
65°C (150°F)BRT-L 0.8
19 mm x 72 mm
200°C (390°F)BRT-41AHT 1.0
19 mm x 120 mm
480°C (900°F)BRT-4HT*** .15
165 mm x 19 mm 41 mm diameter 100 mm x 100 mm
* Optional brackets are available; see Banner Photoelectric Product Catalog ** Target has micro-prism geometry
NOTE: The range of all retroreflective sensors is specified
using target model BRT-3.Sensing range and signal strength at any given sensor-to-target distance will vary due to target reflectivity and target area. A “Reflectivity Factor” is included for each target model to help predict sensor performance, relative to the excess gain curve plotted for target model BRT-3. Consider, also, target area when predicting performance.
!
Loading...