Banner DX80DR2M-H3E-NB-KR User Manual

Page 1

Sure Cross

209529

MultiHop H3E-NB-KR Data Radio

Datasheet

The Sure Cross® wireless system is a radio frequency network with integrated I/O that operates in most environments to eliminate the need for wiring runs. Wireless MultiHop data radio networks are formed around a MultiHop master and one or more slaves and extend the range of a Modbus or other serial communication network.

• Wireless industrial I/O device with four thermocouple inputs, two NPN discrete inputs, one thermistor input, and two NMOS discrete outputs

•

Flex

Power® power options allow for 10 to 30 V dc, solar, and battery power sources for low power

applications.

• Self-healing, auto-routing RF network with multiple hops extends the network’s range

• Serial and I/O communication on a Modbus platform

• Message routing improves link performance

• DIP switches select operational modes: master, repeater, or slave

• Built-in site survey mode enables rapid assessment of a location’s RF transmission properties

• Frequency Hopping Spread Spectrum (FHSS) technology ensures reliable data delivery within the unlicensed Industrial, Scientiﬁc, and Medical (ISM) band

For additional information, updated documentation, and a list of accessories, refer to Banner Engineering's website,

wireless

WARNING:

• Do not use this device for personnel protection

• Using this device for personnel protection could result in serious injury or death.

• This device does not include the self-checking redundant circuitry necessary to allow its use in personnel safety applications. A device failure or malfunction can cause either an energized (on) or de-energized (off) output condition.

Important:

• Electrostatic discharge (ESD) sensitive device

• ESD can damage the device. Damage from inappropriate handling is not covered by warranty.

• Use proper handling procedures to prevent ESD damage. Proper handling procedures include leaving devices in their anti-static packaging until ready for use; wearing anti-static wrist straps; and assembling units on a grounded, staticdissipative surface.

www.bannerengineering.com/

Models

Models Frequency Power Housing I/O

Inputs: Two NPN discrete, four thermocouple, one thermistor (internal)

Outputs: Two NMOS discrete

Serial interface: RS-232

DX80DR2M-H3E-NB-KR 2.4 GHz ISM Band

10 to 30 V dc or integrated battery (ships without the battery)

IEC IP65; NEMA 4X

Conﬁguration Instructions

Setting Up Your MultiHop Network

To set up and install your wireless MultiHop network, follow these steps:

1. If your radios have DIP switches, conﬁgure the DIP switches of all devices.

2. Connect the sensors to the MultiHop radios if applicable.

3. Apply power to all devices.

4. If your MultiHop radio has rotary dials, set the MultiHop Radio (Slave) ID. If your MultiHop radio has no rotary dials, continue to the next step.

5. Form the wireless network by binding the slave and repeater radios to the master radio. If the binding instructions are not included in this datasheet, refer to the quick start guide or product manual.

6. Observe the LED behavior to verify the devices are communicating with each other. Conﬁgure any I/O points to use the sensors connected to the Sure Cross devices.

8. Conduct a site survey between the MultiHop radios. If the site survey instructions are not included in this datasheet, refer to the product manual.

Original Document 209529 Rev. A

18 January 2019

Page 2

Sure Cross® MultiHop H3E-NB-KR Data Radio

9. Install your wireless sensor network components. If the installation instructions are not included in this datasheet, refer to the product manual.

For additional information, refer to one of the following documents:

• MultiHop Data Radio Quick Start Guide:

• MultiHop Data Radio Instruction Manual:

• MultiHop Register Guide (End User Edition):

152653

151317

155289

Conﬁgure the DIP Switches

Before changing DIP switch positions, disconnect the power. DIP switch changes are not recognized until after power is cycled to the device.

Accessing the Internal DIP Switches

To access the internal DIP switches, follow these steps:

1. Unscrew the four screws that mount the cover to the bottom housing.

2. Remove the cover from the housing without damaging the ribbon cable or the pins the cable plugs into.

3. Gently unplug the ribbon cable from the board mounted into the bottom housing.

4. Remove the black cover plate from the bottom of the device's cover. The DIP switches are located behind the rotary dials.

After making the necessary changes to the DIP switches, place the black cover plate back into position and gently push into place. Plug the ribbon cable in after verifying that the blocked hole lines up with the missing pin. Mount the cover back onto the housing.

DIP Switch Settings (MultiHop)

Switches

Device Settings 1 2 3 4 5 6 7 8

Serial line baud rate 19200 OR User deﬁned receiver slots OFF ¹ OFF ¹

Serial line baud rate 38400 OR 32 receiver slots OFF ON

Serial line baud rate 9600 OR 128 receiver slots ON OFF

Serial line baud rate Custom OR 4 receiver slots ON ² ON ²

Parity: None OFF ¹ OFF ¹

Parity: Even OFF ON

Parity: Odd ON OFF

Disable serial (low power mode) and enable the receiver slots select for switches 1-2

Transmit power

900 MHz radios: 1.00 Watt (30 dBm)

2.4 GHz radios: 0.065 Watts (18 dBm) and 60 ms frame

Transmit power

900 MHz radios: 0.25 Watts (24 dBm)

2.4 GHz radios: 0.065 Watts (18 dBm) and 40 ms frame

Application mode: Modbus OFF ¹

Application mode: Transparent ON

MultiHop radio setting: Repeater OFF ¹ OFF ¹

MultiHop radio setting: Master OFF ON

MultiHop radio setting: Slave ON ² OFF ²

MultiHop radio setting: Reserved ON ON

ON ² ON ²

OFF ¹

¹ Default conﬁguration

² Default conﬁguration for the E housing models only

Application Mode

The MultiHop radio operates in either Modbus mode or transparent mode. Use the internal DIP switches to select the mode of operation. All MultiHop radios within a wireless network must be in the same mode.

Modbus mode uses the Modbus protocol for routing packets. In Modbus mode, a routing table is stored in each parent device to optimize the radio trafﬁc. This allows for point to point communication in a multiple data radio network and acknowledgement/retry of radio packets. To access a radio's I/O, the radios must be running in Modbus mode.

In transparent application mode, all incoming packets are stored, then broadcast to all connected data radios. The data communication is packet based and not speciﬁc to any protocol. The application layer is responsible for data integrity. For one to one data radios it is possible to enable broadcast acknowledgement of the data packets to provide better throughput. In transparent mode, there is no access to the radio's I/O.

Baud Rate and Parity

The baud rate (bits per second) is the data transmission rate between the device and whatever it is physically wired to. Set the parity to match the parity of the device you are wired to.

2 www.bannerengineering.com - Tel: + 1 888 373 6767 P/N 209529 Rev. A

Page 3

BAT

GND

A3+

PWR

DO1

DI1

A1-

A1+

A3-

A2-

A2+

A4+

GND

DI2

A4-

DO2

PWR

Discrete IN

PWR

10-30V dc

Discrete IN

GND

dc common

Sure Cross

MultiHop H3E-NB-KR Data Radio

Disable Serial

If the local serial connection is not needed, disable it to reduce the power consumption of a data radio powered from the solar assembly or from batteries. All radio communications remain operational.

Receiver Slots

The number of receiver slots indicates the number of times out of 128 slots/frames the radio can transmit to its parent radio. Setting a slave’s receiver slots to 4 reduces the total power consumption by establishing that the slave can only transmit to its parent four times per 128 slots.

Transmit Power Levels/Frame Size

The 900 MHz data radios can be operated at 1 watt (30 dBm) or 0.250 watt (24 dBm). For most models, the default transmit power is 1 watt.

For 2.4 GHz radios, the transmit power is ﬁxed at 0.065 watt (18 dBm) and DIP switch 5 is used to set the frame timing. The default position (OFF) sets the frame timing to 60 milliseconds. To increase throughput, set the frame timing to 40 milliseconds.

Prior to date code 15341 and radio ﬁrmware version 3.6, the frame timing was 40 ms (OFF) or 20 ms (ON).

Wire Your Sure Cross® Device

Use the following wiring diagrams to ﬁrst wire the sensors and then apply power to the Sure Cross devices.

Wiring for DX80...E Radios

Connecting power to the communication pins will cause permanent damage. The integrated battery DX80...E radios may also be powered by 10 V dc to 30 V dc. The power for the sensors can be supplied by the radio's SPx terminals or from the 10 V dc to 30 V dc used to power the radio. The BAT connection is a low voltage connection to the internal battery. Remove the internal battery if a low voltage source is connected to the BAT terminal. When powering the device from the integrated battery, the BAT connection must remain open.

Integrated battery (RS-485) for P1E, M-H1E, M-H12E, and P16E Models

1 10 V dc to 30 V dc (optional) 10 V dc to 30 V dc (optional)

2 RS-485 / D1 / B / + RS-232 Tx

3 dc common (GND) dc common (GND)

4 RS-485 / D0 / A / - RS-232 Rx

Integrated battery (RS-232) for P3E, P4E, M-H3E, and M-H4E Models

Terminal Block (E Housing)

Refer to the Class I Division 2/Zone 2 control drawings (p/n

143086

) for wiring speciﬁcations and limitations.

Ax+ and Ax–. Analog IN x. Analog inputs for devices requiring more than one connection, such as thermocouples or RTDs. When there is no Ax–, use Ax+ as an analog input.

DIx. Discrete IN DOx. Discrete OUT GND. Ground/dc common connection PWR. 10 to 30 V dc power connection

Wiring Diagrams for Discrete Inputs

Connecting power to the communication pins will cause permanent damage. For the DX8 the wiring board and GND in the wiring diagram refers to V- on the wiring board. To power the sensor using the switch power output (SPx), replace the PWR with SPx in these wiring diagrams.

Discrete Input Wiring for PNP Sensors

...C models, PWR in the wiring diagram refers to V+ on

Discrete Input Wiring for NPN Sensors

Wiring Diagrams for Discrete Outputs

P/N 209529 Rev. A www.bannerengineering.com - Tel: + 1 888 373 6767 3

...C models, PWR in the wiring diagram refers to V+ on

Page 4

Ax+

Ax−

−

Sure Cross® MultiHop H3E-NB-KR Data Radio

Wiring Diagram for Thermocouple Inputs

Thermocouple: When wiring the thermocouple, x is the same number. For example, a thermocouple is wired to A1+ and A1-.

Set the MultiHop Radio (Slave) ID

On a MultiHop radio, use the rotary dials to set the device’s MultiHop Radio ID.

Modbus Slave IDs 01 through 10 are reserved for slaves directly connected to the host (local I/O). Polling messages addressed to these devices are not relayed over the wireless link. Use Modbus Slave IDs 11 through 60 for MultiHop master, repeater, and slave radios. Up to 50 devices (local slaves and remote slaves) may be used in this system.

With the left dial acting as the left digit and the right dial acting as the right digit, the MultiHop Radio ID can be set from 01 through 60.

MultiHop Conﬁguration Software

Use Banner’s MultiHop

Conﬁguration Software to view your MultiHop radio network and conﬁgure the radio and its I/O.

The software connects to a MultiHop master radio using one of four methods.

• Serial; using a USB to RS-485 (for RS-485 radios) or a USB to RS-232 (for RS-232 radios) converter cable.

• Modbus TCP; using an Ethernet connection to an Ethernet radio master.

• Serial DXM; using a USB cable to a DXM Controller to access a MultiHop master radio.

• TCP DXM: using an Ethernet connection to a DXM Controller to access a MultiHop master radio.

For MultiHop DX80DR* models, Banner recommends using BWA-UCT-900, an RS-485 to USB adapter cable with a wall plug that can power your 1 Watt MultiHop radio while you conﬁgure it. The adapter cable is not required when connecting to a DXM Controller.

Download the most recent software revision from the Wireless Reference Library on Banner Engineering's website:

www.bannerengineering.com

Installing Your Sure Cross® Radios

Please refer to one of the following instruction manuals for details about successfully installing your wireless network components.

• MultiHop Data Radio Instruction Manual:

151317

Modbus Registers

Min. Value Max. Value

1 1 Discrete IN 1 - 0 1 DI1

2 2 Discrete IN 2 - 0 1 DI2

3 3 Thermocouple IN 1 °F/°C –1638.3 +1638.4 A1+/–

4 4 Thermocouple IN 2 °F/°C –1638.3 +1638.4 A2+/–

5 5 Thermocouple IN 3 °F/°C –1638.3 +1638.4 A3+/–

6 6 Thermocouple IN 4 °F/°C –1638.3 +1638.4 A4+/–

7 7

8 8 Thermistor IN 1 (internal) °F/°C –1638.3 +1638.4 Internal

In low resolution mode, the minimum and maximum values are –16383 and +16384.

The easiest way to conﬁgure a MultiHop radio is to use the MultiHop Conﬁguration Tool. This software tool allows you to conﬁgure each input and output, including setting the type of thermocouple. You may also use Modbus commands to conﬁgure the inputs. For more information on using Modbus commands, refer to the MultiHop Product Manual (p/n download from Banner Engineering's website (

www.bannerengineering.com

151317

) or the MultiHop Register Guide (p/n

)

155289

). Both manuals are available for

4 www.bannerengineering.com - Tel: + 1 888 373 6767 P/N 209529 Rev. A

Page 5

Sure Cross® MultiHop H3E-NB-KR Data Radio

Min. Value Max. Value

501 1 Discrete OUT 1 - 0 1 DO1

502 2 Discrete OUT 2 - 0 1 DO2

Temperature Parameters

The following parameters are used to conﬁgure analog inputs involving temperature and are typically used to conﬁgure thermocouple or RTD inputs.

Registers for Analog Parameters (4xxxx)

IN 1 (3301-3320) IN 2 (3321-3340) IN 3 (3341-3360) IN 4 (3361-3380)

3304 3324 3344 3364 Temperature Degrees C/F

3305 3325 3345 3365 Temperature Scaling

3306 3326 3346 3366 Thermocouple Type

3307 3327 3347 3367 Temperature Resolution

Parameters

Temperature Degrees C/F

Set to 1 to represent temperature units in degrees Fahrenheit, and set to 0 (default) to represent temperature units in degrees Celsius.

Temperature Resolution

Thermocouples and RTDs may record temperatures in either high resolution (tenths of a degree) or low resolution (whole degree). Write a 0 to select high resolution (default) or a 1 to select low resolution. Choosing high or low resolution changes the range of temperatures that can be written to the register.

Temperature Scaling

Set to 1 to store temperatures the same way as the DX80 devices (measured temp × 20) represent temperature. Set to 0 (default) to store temperature values in tenths of a degree (measured temp × 10). For example, if the measured temperature is 20.5 degrees, using temperature scaling set to 1 would store the temperature value as 410; using temperature scaling set to 0 would store the temperature as 205.

Thermocouple Type

Write the listed value to this register to select a thermocouple type. The default conﬁguration is set to a Type B thermocouple (0).

Value Thermocouple Type Value Thermocouple Type Value Thermocouple Type

0 B 5 J 10 P

1 C 6 K 11 R

2 D 7 L 12 S

3 E 8 M 13 T

4 G 9 N 14 U

Modbus Addressing Convention

All Modbus addresses refer to Modbus holding registers. When writing your own Modbus scripts, use the appropriate commands for interfacing to holding registers. Parameter description headings refer to addresses in the range of 40000 as is customary with Modbus convention.

Modbus Register

Change the factory default settings for the inputs, outputs, and device operations using the device Modbus registers. To change parameters, set the data radio network to Modbus mode and assign the data radio a valid Modbus slave ID.

Generic input or output parameters are grouped together based on the device input or output number: input 1, input 2, output 1 etc. Operation type speciﬁc parameters (discrete, counter, analog 4 to 20 mA) are grouped together based on the I/O type number: analog 1, analog 2, counter 1, etc. Not all inputs or outputs may be available for all models. To determine which speciﬁc I/O is available on your model, refer to the Modbus Input/ Output Register Maps listed in the device's datasheet. For more information about registers, refer to the MultiHop Product Manual (p/n

Conﬁguration

151317

Factory Default Conﬁguration

Discrete Inputs (NPN)

Enable Sample Boost Enable Boost Warmup Boost Voltage

ON 40 ms OFF OFF OFF OFF NPN OFF OFF

Thermocouple Inputs

Enable

ON 5 sec 16384 –16383 ON

Sample Analog Max Analog Min Enable Fullscale

Extended Input

Read

NPN/PNP Sample High Sample Low

P/N 209529 Rev. A www.bannerengineering.com - Tel: + 1 888 373 6767 5

Page 6

Sure Cross® MultiHop H3E-NB-KR Data Radio

Thermistor Inputs

Enable Sample Analog Max Analog Min Enable Fullscale Enable Deg F Temp Scaling

ON 5 sec 16383 –16384 OFF Deg F × 20

Storage and Sleep Modes

Storage Mode (applies to battery-powered models only)—While in storage mode, the radio does not operate. All Sure Cross® radios powered from an integrated battery ship from the factory in storage mode to conserve the battery. To wake the device, press and hold button 1 for 5 seconds. To put any

Flex

when the LEDs stop blinking, but in some models, the LCD remains on for an additional minute after the radio enters storage mode. After a device has entered storage mode, you must wait 1 minute before waking it.

Sleep Mode (applies to both battery and 10–30 V dc powered models)—During normal operation, the Sure Cross radio devices enter sleep mode after 15 minutes of operation. The radio continues to function, but the LCD goes blank. To wake the device, press any button.

Power® or integrated battery Sure Cross radio into storage mode, press and hold button 1 for 5 seconds. The radio is in storage mode

Installing or Replacing the Battery (DX80...E Models)

To replace the lithium "D" cell battery in any integrated housing model, follow these steps.

1. Remove the four screws mounting the face plate to the housing and remove the face plate. Do not remove the radio cover from the face plate.

2. Remove the discharged battery and replace with a new battery. Only use a 3.6 V lithium battery (see list below).

3. Verify the battery’s positive and negative terminals align to the positive and negative terminals of the battery holder mounted within the case.

Caution: There is a risk of explosion if the battery is replaced incorrectly.

4. After replacing the battery, allow up to 60 seconds for the device to power up.

For outside or high humidity environments, dielectric grease may be applied to the battery terminals to prevent moisture and corrosion buildup.

Properly dispose of your used battery according to local regulations by taking it to a hazardous waste collection site, an e-waste disposal center, or other facility qualiﬁed to accept lithium batteries. As with all batteries, these are a ﬁre, explosion, and severe burn hazard. Do not burn or expose them to high temperatures. Do not recharge, crush, disassemble, or expose the contents to water.

For hazardous or non-hazardous locations, the replacement battery model number is BWA-BATT-001 (Xeno model number XL-205F). For non-hazardous locations only, the replacement battery model number is BWA-BATT-011. For pricing and availability, contact Banner Engineering.

Speciﬁcations

MultiHop 2.4 GHz Korean Radio Speciﬁcations

Radio Range

Antenna Minimum Separation Distance

Radio Transmit Power

Spread Spectrum Technology

2.4 GHz, 65 mW: Up to 3.2 km (2 miles)

2.4 GHz, 65 mW: 0.3 m (1 ft)

2.4 GHz, 65 mW: 18 dBm (65 mW) conducted, less than or equal to 20 dBm (100 mW) EIRP

FHSS (Frequency Hopping Spread Spectrum)

RS-232 Communication Speciﬁcations

Communication Hardware (MultiHop RS-232)

Interface: 2-wire RS-232 Baud rates: 9.6k, 19.2k (default), or 38.4k via DIP switches; 1200 and 2400 via the MultiHop Data format: 8 data bits, no parity, 1 stop bit

MultiHop H3E-NB-KR

Supply Voltage

Integrated Battery or 10 to 30 V dc

Power Consumption

Master radio consumption (900 MHz): Maximum current draw is < 100 mA and typical current draw is < 30 mA at 24 V dc. (2.4 GHz consumption is less.) Repeater/slave radio consumption (900 MHz): Maximum current draw is < 40 mA and typical current draw is < 20 mA at 24 V dc. (2.4 GHz consumption is less.)

Interface

Two bi-color LED indicators, Two buttons, Six character LCD

Radio range is with the 2 dB antenna that ships with the product. High-gain antennas are available, but the range depends on the environment and line of sight. Always verify your wireless network's range by performing a Site Survey.

Speciﬁcations

2.4 GHz Compliance for Korean Radio Models KCC-CRM-BE2-DX

Antenna Connection

Ext. Reverse Polarity SMA, 50 Ohms Max Tightening Torque: 0.45 N·m (4 lbf·in)

Radio Packet Size (MultiHop)

2.4 GHz: 75 bytes (37 Modbus registers)

Conﬁguration Tool

Housing

Polycarbonate housing and rotary dial cover; polyester labels; EDPM rubber cover gasket; nitrile rubber, non-sulphur cured button covers Weight: 0.26 kg (0.57 lbs) Mounting: 1/4-inch or M7 (SS M7 hardware included) Max. Tightening Torque: 0.56 N·m (5 lbf·in)

Wiring Access

Two 1/2-inch NPT

6 www.bannerengineering.com - Tel: + 1 888 373 6767 P/N 209529 Rev. A

Page 7

( 3.2 )

35 mm

6 mm

( 4)

20 mm

72 mm

Tube

Sure Cross® MultiHop H3E-NB-KR Data Radio

Discrete Inputs

Rating: 3 mA max current at 30 V dc Sample Rate: 40 milliseconds ON Condition (NPN): Less than 0.7 V OFF Condition (NPN): Greater than 2 V or open

Thermocouple Inputs (MultiHop)

Sample Rate: 8 seconds Accuracy: 0.1% of full scale reading + 0.8 °C

0.1 °C, 24-bit A/D converter

Thermistor Input (MultiHop)

Model: Omega’s 44006 or 44031 family of 10 kOhm thermistors Sample Rate: 1 second Accuracy: 0.4 °C (10 °C to 50 °C); Up to 0.8 °C (−40 °C to 85 °C)

Environmental Speciﬁcations for the E Housing

Operating Conditions

–40 °C to +85 °C (–40 °F to +185 °F) (Electronics); –20 °C to +80 °C (–4 °F to +176 °F) (LCD) 95% maximum relative humidity (non-condensing) Radiated Immunity: 10 V/m (EN 61000-4-3)

Shock and Vibration

IEC 68-2-6 and IEC 68-2-27 Shock: 30g, 11 millisecond half sine wave, 18 shocks Vibration: 0.5 mm p-p, 10 to 60 Hz

Accessories

Thermistor Probes

Thermocouple Notes

Each thermocouple input must be isolated from ground and shielded for proper operation.

Discrete Outputs

ON Condition: Less than 0.7 V OFF Condition: Open

Discrete Output Rating (MultiHop NMOS)

Less than 1 A max current at 30 V dc ON-State Saturation: Less than 0.7 V at 20 mA

Certiﬁcations

Environmental Ratings

IEC IP65 Refer to the Sure Cross® MultiHop Product Instruction Manual (p/n installation and waterprooﬁng instructions.

Operating the devices at the maximum operating conditions for extended periods can shorten the life of the device.

151317

) for

BWA-THERMISTOR-PROBE-001

• Temperature sensor with thermistor PS103G2

• Beta Value(K) 0 ~50°C: 3575

• Base thermistor accuracy of 0.2%

• Operating Temperature Range: –20 °C to +105 °C

• Maximum Power Rating: 30 mW at 25 °C; derated to 1 mW at 125 °C

• Dissipation Constant: 1 mW/°C

• Plated nickel

ﬁnish; PVC insulation

Included with the DX80..E Models

• Mounting hardware kit

• BWA-HW-003: PTFE tape

• BWA-9O2-C (900 MHz) or BWA-2O2-C (2.4 GHz): Antenna, 2 dBd Omni, Rubber Swivel RP-SMA Male. (Not included with Internal antenna models)

• BWA-BATT-001: Replacement battery, 3.6 Volt, "D" Lithium Cell

• BWA-HW-032: Access Hardware for "E" Housing (One each of 1/2-inch plug, 1/2-inch gland)

128185

• Product datasheet and product family Quick Start Guide (

for DX80 Gateways or

152653

for MultiHop models)

Warnings

Install and properly ground a the ground wire as short as possible and make all ground connections to a single-point ground system to ensure no ground loops are created. No surge suppressor can absorb all lightning strikes; do not touch the Sure Cross® device or any equipment connected to the Sure Cross device during a thunderstorm.

Exporting Sure Cross® Radios. It is our intent to fully comply with all national and regional regulations regarding radio frequency emissions. Customers who want to re-export this product to a country other than that to which it was sold must ensure the device is approved in the destination country. A list of approved countries appears in the products were certiﬁed for use in these countries using the antenna that ships with the product. When using other antennas, verify you are not exceeding the transmit power levels allowed by local governing agencies. Consult with Banner Engineering Corp. if the destination country is not on this list.

qualiﬁed surge suppressor when installing a remote antenna system. Remote antenna conﬁgurations installed without surge suppressors invalidate the manufacturer's warranty. Keep

Radio Certiﬁcations

section of the product manual. The Sure Cross wireless

P/N 209529 Rev. A www.bannerengineering.com - Tel: + 1 888 373 6767 7

Page 8

Sure Cross® MultiHop H3E-NB-KR Data Radio

Banner Engineering Corp. Limited Warranty

Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product.

THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE.

This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.

Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously manufactured by Banner Engineering Corp. Any misuse, abuse, or improper application or installation of this product or use of the product for personal protection applications when the product is identiﬁed as not intended for such purposes will void the product warranty. Any modiﬁcations to this product without prior express approval by Banner Engineering Corp will void the product warranties. All speciﬁcations published in this document are subject to change; Banner reserves the right to modify product speciﬁcations or update documentation at any time. Speciﬁcations and product information in English supersede that which is provided in any other language. For the most recent version of any documentation, refer to:

For patent information, see

www.bannerengineering.com/patents

www.bannerengineering.com