Bakers Pride BP-200 Installation Manual
1/2 SIZE ELECTRIC CONVECTION OVEN-
!
BAKERSBAKERS
PRIDEPRIDE
INSTALLATION AND OPERATING INSTRUCTIONS
Cyclone SERIES
Model: BP-200
INTENDED FOR OTHER THAN HOUSEHOLD USE
RETAIN THIS MANUAL FOR FUTURE REFERENCE
OVEN MUST BE KEPT CLEAR OF COMBUSTIBLES AT ALL TIMES
FOR YOUR SAFETY: Do not store or use gasoline or other flammable vapors and
liquids in the vicinity of this or any other appliance.
!
WARNING: Improper installation, adjustment, alteration, service or maintenance
!
!
This equipment has been engineered to provide you with year round dependable service when used
according to the instructions in this manual and standard commercial kitchen practices.
(914) 576-0200 Phone (800) 431-2745 US & Canada
(914) 576-0605 Fax www.bakerspride.com Web Address
can cause property damage, injury or death. Read the Installation, Operating and
Maintenance Instructions thoroughly before installing or servicing this equipment.
WARNING: Initial heating of oven may generate smoke or fumes and must be
done in a well-ventilated area. Overexposure to smoke or fumes may cause
nausea or dizziness.
R
T
E
E
T
K
N
I
CM
D
V
E
E
I
R
F
I
P/N U4162A 1-08
BAKERS PRIDE OVEN CO., INC.
30 Pine Street
New Rochelle, NY 10801
!
!
1
INDEX
TECHNICAL DATA ................................................................................................................................................................ 2
Data plate ............................................. ......................................................................................................................... 2
Power supply terminal board ..........................................................................................................................................2
After sales service .......................................................................................................................................................... 2
Specifications.................................................................................................................................................................. 3
PART RESERVED FOR INSTALLER......................................................................................................................................3
Safety standards .............................................................................................................................................................3
Environmental standards ................................................................................................................................................3
Transport and unpacking ................................................................................................................................................3
Installation instructions ................................................................................................................................................... 4
Electrical connections .....................................................................................................................................................4
Automatic safety and control devices of the oven .......................................................................................................... 5
Replacing spare parts .....................................................................................................................................................5
PART RESERVED FOR USER ...............................................................................................................................................6
General safety standards ................................................................................................................................................6
Use of the oven ...............................................................................................................................................................6
Routine maintenance ......................................................................................................................................................7
What to do in case of a breakdown or long periods of disuse ........................................................................................8
PARTS LIST & EXPLODED VIEW .........................................................................................................................................9
ELECTRICAL DIAGRAM ........................................................................................................................................................11
WARRANTY.............................................................................................................................................................................12
IMPORTANT FOR FUTURE REFERENCE
Please complete this information and retain this manual for the life of the equipment. For
Warranty Service and/or Parts, this information is required.
Model Number Serial Number Date Purchased
TECHNICAL DATA
DATA PLATE
The data plate containing the oven characteristics is glued to the back.
POWER SUPPLY TERMINAL BOARD
The power supply terminal block is inside the right side of the oven. A small data plate positioned near the terminal block
states the types of connections which are possible.
AFTER SALES SERVICE
Technical Service: Perfect operation over time of our convection ovens is ensured by a wide-ranging technical service
network. Specialized technicians are ready to intervene in a timely manner to ensure the work of food services professionals
continues uninterrupted.
Warranty: All our convection ovens undergo careful operating tests before they go on the market, as shown by the test
certificate that is enclosed with each one of them and by the one-year guarantee.
2
Dimensions
W x D x L
SPECIFICATIONS ½ Oven Technical Data
No. of pans
or racks
Power supply
Power
External dimensions: 27” x 21 3/4” x 25 1/4”
Internal dimensions: 21 ½” x 14 ½” x 16 1/8”
Rack dimensions: ½ size
27”
For further electrical details, refer to the electrical diagram in this manual.
21 3/4”
4
1 Phase 15, Amp, 240V, 60Hz
Plug NEMA 6-20P standard
25 1/4”
Kw 3.2
PART RESERVED FOR INSTALLER
SAFETY STANDARDS
! The installer must read this booklet carefully before installing the convection oven.
! Installation and subsequent maintenance, cleaning, inspection and repairs must be carried out with the electrical power
supply disconnected.
! Installation of the ovens must be in comply with current standards in the country of use. Otherwise the manufacturer shall not
honor the warranty in the event of direct or indirect damage.
! Installation, adjustment and assistance are to be carried out by qualified personnel in compliance with current
accident prevention legislation in the country of use. The installer must also check for any fire prevention
regulations.
! The manufacturer shall not be held liable for any damage arising from improper use of the convection oven, unauthorized
modifications and anything not covered by this manual.
ENVIRONMENTAL STANDARDS
All materials used for packaging are compatible with environmental protection standards. They may be stored without any hazard,
or disposed of in accordance with current laws in the country of use. Do not leave the plastic coverings within reach of children
or animals as they are potentially hazardous. The plastic components which can be disposed of and recycled are marked as
follows: POLYETHYLENE: packaging outer film, instructions bag, etc. POLYPROPYLENE: clips, etc.
TRANSPORT AND UNPACKING
Any movement of the oven must be carried out by suitable means
such as a forklift or pallet loader. These must be at least half as
large as the convection oven (see fig.1). If it is necessary to store
the oven temporarily, keep it in a covered, ventilated place at a
temperature from 14°F to 122°F, with humidity no higher than
95%.
Use protective gloves and remove the packaging. Lift the oven
with a forklift, remove the base and place it in its intended
location.
After removing the packaging, immediately check the
condition of the oven. If in doubt, do not use the oven.
Contact an authorized retailer.
3
Figure 1
INSTALLATION INSTRUCTIONS
POSITIONING AND SET-UP FOR USE
1) Place the machine in its place of intended use in compliance with the following instructions:
A) Check that there is enough space (minimum 8”) from any walls or obstacles which may prevent proper air flow
(fig.2).
B) Check that maintenance can be performed with a certain freedom of movement.
C) Avoid placing the oven in places with poor air circulation, in places exposed to sunlight, where there are high
temperatures, near heat sources or in windy locations (fig.3).
D) Ambient air temperature must not exceed 89°F. Above that temperature, proper operation of the oven cannot be
ensured.
E) Always install the oven under a properly operating aspiration hood for the extraction of vapors.
2) Remove the film which covers some parts of the oven before starting to use it.
3) Clean all substances, including glue residue. Do not use abrasive substances.
4) Position the machine so that it is perfectly level and set the height by means of the leveling feet (fig. 4).
Figure 2 Figure 3 Figure 4
8”
1
9”
8”
19”
8”
19”
ELECTRICAL CONNECTIONS
The oven is setup for operation at the voltage set forth on the technical
data plate. All ovens are provided with a power cord. The flexible cable
for connection to the electrical mains must not have characteristics
which are less than those of a type with rubber insulation mod. H07RN
F and it must have a section which corresponds with that set forth in the
section “Technical Data” of the oven. The cable must also be anchored
to the frame with the cable clamp, the screw of which can be reached
through a hole in the frame. It must in any case be positioned in such a
way that at no point does it reach a temperature which is 122°F greater
than the ambient temperature. It must be type SJTO plug 20A 250V P
section 3xAWG12.
The connection to the electrical line must be made by placing an
automatic switch of sufficient capacity (see “Technical data” of the
oven) and with an opening distance between contacts of at least 3 mm.
Also, during operation of the oven, the power supply must not vary from
the nominal voltage value by ±10%.
The oven MUST be earthed by means of the terminal which carries the
earth symbol on the connection board (fig. 6).
It must also be inserted in an equipotential system (the efficiency of
which must be checked in accordance with current standards) using
the terminal with the equipotential symbol (fig. 6A). It is located near the
electrical cable entry on the panel of the oven bottom.
The manufacturer will not be held liable if this accident prevention
standard is not adhered to.
Figure 5
Figure 6 Figure 6A
4
Loading...