Bacharach IAM-100 Quick Start Guide

INTEGRATED AREA MONITOR

and CONTROLLER

INSTALLATION GUIDE

P/N: 6209-9002

Revision 0

January 13, 2016

IAM-100

Controller

CAUTION: DO NOT MOUNT the

IAM-100 or controller in an area

that may contain flammable liquids
or vapors. Operaon of electrical
equipment in such an area cons-

tutes a safety hazard.

WARNING: Strictly follow the
instrucons in the User Manuals
(part number 6209-9000 and 6709-

9000) available at
www.MyBacharach.com.

The IAM-100 is an ideal soluon for gas detecon in
the following occupied spaces with variable refrigerant
flow (VRF) or variable refrigerant volume (VRV)

systems:

• hotel rooms

• storage facilies

• conference rooms

• theaters

• apartment blocks

• airports

• office buildings

• light industrial spaces

• air condioned spaces

• large systems requiring many sensors.

The instrument is powered by 110 VAC/60 HZ or
220 VAC/50 Hz; 11 W Max.

2: SAFETY INSTRUCTIONS

USER MANUAL: Before using this equipment,

carefully read and strictly follow the User Manuals
(part numbers 6209-9000 and 6709-9000). The user

must fully understand and strictly observe the

instrucons. Use the equipment only for the
purposes listed and under the condions specified in

that document.

CODE COMPLIANCE: Comply with all local and
naonal laws, rules and regulaons associated with

this equipment.

GENUINE PARTS: Use only genuine Bacharach spare
parts and accessories, otherwise proper funconing

of the equipment may be impaired.
TECHNICIAN USE ONLY: This unit must be installed

by a suitably qualified technician who will install this
unit in accordance with these instrucons and the
standards in their parcular industry/country. Opera­tors of the unit should be aware of the regulaons
and standards in their industry/country for the
operaon of this unit. These notes are only intended

as a guide and the manufacturer bears no responsi-

bility for the installaon or operaon of this unit.

Failure to install and operate the unit in accordance

with these instrucons and with industry guidelines

may cause serious injury including death and the

manufacturer will not be held responsible in this

regard.
SAFE MOUNTING: This monitor must be connected

by a marked, suitably located and easily reached

switch or circuit-breaker as means of disconnecon.

IMPORTANT: For compliance with
EN378, at least one detector shall

be installed in each occupied space

being considered and the locaon

of detectors shall be chosen in

relaon to the refrigerant and they
shall be located where the refriger­ant from the leak will collect. In

this case refrigerants are heavier
than air and detectors should have

their sensors mounted low, e.g., at

less than bed height in the case of
a hotel or other similar Category
Class A space. Ceiling voids or
other voids if not sealed are part of
the occupied space.

CAUTION: Monitoring ceiling voids

in a hotel room would not strictly
comply with EN378.

IMPORTANT: Mount in-room sen­sors at less than the normal heights
of the occupants. E.g., in a hotel
room this is less than bed height

(between 100 and 300 mm [4 and
12 inches] off the floor). Avoid
dras and heat sources (liek radia­tors), and avoid sources of steam.

WARNING: Strictly follow the
instrucons in the User Manuals
(part number 6209-9000 and 6709-

9000).

3: WEIGHTS AND DIMENSIONS

IAM-100 Housings Specifications

Standard Size: 147x88x62 mm [5.8x3.5x2.4 in]

Weight: 633 g [1.4 lbs]

Faceplate
(Brushed Steel)

Size: 86x86 mm [3.4x3.4 in]
Weight: 86 g [0.2 lbs]

4: MOUNTING

ENVIRONMENTAL CONSIDERATIONS: Carefully

consider the full range of environmental condions to
which the instruments will be exposed.

TARGET GAS CONSIDERATIONS: The physical data of
the gas or vapor to be detected must be observed.

APPLICATION CONSIDERATIONS: The specifics of the
applicaon (for example, possible leaks, air
movement/dra, etc.) must be observed.

ACCESSIBILITY CONSIDERATIONS: The degree of
accessibility required for maintenance purposes must
be granted.

ACCESSORY CONSIDERATIONS: The types of oponal
and accessory equipment that will be used with the

system must be kept in mind.
ELECTRONIC CONSIDERATIONS: The system contains

sensive electronic components that can be easily

damaged. Do not touch nor disturb any of these
components.

Mount the IAM-100 and Controller according to the

above consideraons, product dimensions (see Secon

3), maximum wiring lengths (see Secon 5), and the
corresponding mounng dimensions shown in the
illustraons that follow.

IAM-100

120.6 ± 0.8 mm [4.75 ± 0.03 in]

11.1 mm
[0.4 in]

[1.3 in]

33.4 mm

20.3 mm

[0.8 in]

63.5 mm [2.5 in ]

D = 11.1 mm

[0.4 in]

2 places

130.250 mm [5.1 in]

12.1 mm

[0.5 in]

11.1 mm
[0.4 in]

12.1 mm

[0.5 in]

12.1 mm

[0.5 in]

11.1 mm
[0.4 in]

11.1 mm
[0.4 in]

63.5 mm [2.5 in ]

12.1 mm
[0.5 in]

22.9 mm x 11.1 mm

13 mm x 7.6 mm

[0.5 in x 0.3 in]

2 places

16.5 mm x 11.1 mm
[0.7 in x 0.4 in]

2 places

[0.9 in x 0.4 in]

20.3 mm

[0.8 in]

260.50 mm [10.3 in]

86.9 mm [3.4 in]

1: OPERATING AREA AND CONDITIONS

The IAM-100 is a system that combines sensor and
monitoring features in an integrated unit. It is a
stand-alone system used to detect gases in an area,

room, zone, airspace or airflow. The IAM-100 can be
expanded into large gas detecon systems using the
oponal IAM controller. Up to 16 IAM-100s can
connect to an IAM controller. The controller shows

any sensor in alarm and has relays for control
purposes. These controllers can be connected to

each other enabling the construcon of large gas

detector systems.

AIR CONDITIONER

AIR CONDITIONER

240.50 mm [9.5 in]

224.70 mm [8.8 in]

O5.10mm

[0.20 in]

CONTROLLER

242.50 mm [9.5 in]

O4.60mm [0.18 in]

Mounng
Holes

5: WIRING

NOTE: To make wiring connecons,

you must first open the the IAM-100
by removing the two front cover
screws. Remove the metal faceplate
and locate the connecon termi-

nals.

Refer to the User Manuals (part numbers 6209-

9000 and 6709-9000)

www.MyBacharach.com for detailed wiring

instrucons.

NOTE: The maximum wire size into
terminal blocks is 1.5 mm2 [16
AWG].

WARNING: The main power supply

cable should be of an approved type

based on local regulaons. Connecon
to the main power supply must be made

via an approved, readily-accessible,

switched and fused plug and socket (or
as per local wiring regulaons) wihch
should be within 10 feet (3 meters) of

the control unit.

SHIELD WIRE WARNING: Connect

the shield of the power wires to the

earth ground of the central control
system (e.g., chassis, ground bus bar,

etc.).

1: Strip 0.2 to 0.25 inches (5 to 7 mm)
of wiring insulaon.
2: Connect the wires as indicated.

NOTE: Aer wiring is completed,

carefully re-assemble the enclosure and

its components, nong the keyed

ribbon cable and sensor connectors.

Aer installaon is complete, be sure to
refer to the User Manual (part number

6109-9000)

www.MyBacharach.com for detailed

instrucons on registering the sensors
and configuring the IAM-100 for proper
operaon.

World Headquarters

621 Hunt Valley Circle

New Kensington, PA 15068 USA

Phone: [phone] • Fax: [phone]

Toll Free: 1-800-736-4666

Website: www.MyBacharach.com

E-mail: [e-mail]

114A Georges Street Lower

Dun Laoghaire • Co Dublin • Ireland

Phone: [phone] • Fax: [phone]

available at

available at

No Volt Contacts

5VDC, 10mA Min.

24VDC, 1A Max.

Remote

on off

5: Remote Reset from Panel
On: Enabled
Off: Disabled
1: Delay Seng 1 (See Chart)
2: Delay Seng 2 (See Chart)
3: Latch Seng
On: Manual Reset
Off: Automac Reset
4: Horn Seng
On: Enabled
Off: Disabled

Reset Buon
Access Hole

Access

Screw

Sample

Label

Relay#1Relay

N/C

N/O

Relay Contacts

0V

To

Panel

Jumper Sengs

N/O

COM

5
1
2
3
4

CN6

0.21 mm2 [24 AWG ] Cable
500 m [1640  ] Max (110 V System)
300 m [984 ] Max (220 V System)

#2

COM

Panel
Output

P1 P2

N/C

120/230 VAC

L E N

Main Power

Connectors

VS VREF

for Audible Alarm and Relays

Vent Holes

(Not Shown)

Vent Holes

Serial Number: T012345B 27/04/2012

Gas: R410A Range: 1000 PPM

Standby Voltage: 0.3V

MODEL:

Alarm Voltage: 3.05V

IAM

Voltage: 110V AC 50/60Hz

IAM Printed Circuit Board

(Rear View)

Delay Jumpers 1 and 2

1

2

1

2

1

2

1

2

0 Minutes

(No Delay)

5 Minute

Delay

10 Minute

Delay

15 Minute

Delay

Power

Alarm
LED

LED

15

Access

Screw

Mute

Buon

Panel Interconnect Output

0.21 mm

2

[24 AWG] Cable
500 m [1640 ] Max
(110 V System)
300 m [984 ] Max
(220 V System)

Enclosure

Push
Buon

Mutes

Switch

Horn

Deacvates
Horn

B

Key
Switch

e

r

i

W

k

c

a

l

Red Wire

Horn
(9 VDC, 100 mA Max)

Main Power
Note that the cable should

have strain relief fied.
Main power should be
externally switched and fused.
5A rang is recommended

Key Switch Not Shown
(Deacvates Horn)

Power

LED

Jumper Sengs

HD1: Not Used (Do Not Remove Link)
HD2: Not Used
HD3: Remote Reset:

Enabled

(Link Fied)

(Link Removed)

Disabled

NOTE: Remote Reset MUST be
disabled on Master Panel.

N/O

COM

N/C

N/O

COM

N/C

Relay Contacts

REMOTE

PANEL

LD16
LD15

LD14
LD13

LD12

SW1

LD11
LD10

HD3
HD2
HD1

-

+

CN19

CN17

L

+

E

N

LD9

LD8

LD7
LD6
LD5

LD4
LD3

LD2

LD1

LD17

Transformer

Fuse

16 Channel

IAM Controller

Cable Glands (12 Places)

CN7 CN8 CN9 CN10 CN11 CN12 CN13 CN14 CN15 CN16

CN6

Input Connectors CN1 through CN16

CN1 CN2 CN3 CN4 CN5

Push Buon
Not Shown
(Mutes Horn)

Alarm

LEDs (16
Channels)

Acess

Screws
(2 Places)

HD3
HD2
HD1

�

Unconnected inputs should

be disabled by shorng with

a 2.2 K resistor.

2.2 K�

[24 AWG] Cable

2

500 m [1640 ] Max (110 V System)

To IAM-100 Sensors or Panel

Interconnect Outputs using

300 m [984 ] Max (220 V System)

0.21 mm