BabyTrend 9165TW User Manual

IF YOU EXPERIENCE ANY DIFFICULTY IN USING THIS PRODUCT,

PLEASE CONTACT OUR CUSTOMER SERVICE DEPARTMENT AT

1-800-328-7363 BETWEEN THE HOURS OF 8:00 A.M. AND 4:30 P.M. PACIFIC

STANDARD TIME FOR ASSISTANCE. PLEASE HAVE YOUR MODEL NUMBER AND

MANUFACTURING DATE AVAILABLE WHEN YOU CALL. THIS INFORMATION CAN BE

FOUND ON A SMALL STICKER ON THE INSIDE OF THE STROLLER FRAME.

Read all instructions BEFORE assembly and USE of product.

KEEP INSTRUCTIONS FOR FUTURE USE.

Expedition Double

Jogging Stroller

Type 1: Fixed front wheel

Convenience through innovation and thoughtful design

Type 2: Lockable swivel front wheel

Instruction Manual

03.08

Convenience through innovation and thoughtful design

www.babytrend.com

WARNING

WARNING: Please follow all of these instructions to ensure

the safety of your child. Keep these instructions for future reference.

PARTS

WARNING: Failure to follow these instructions could result in

serious injury or death. Avoid serious injury from falling or sliding out. Always use the safety harness and insure that the children are properly positioned according to these instructions.

WARNING: Never leave children unattended.

• CAUTION: This double jogger is designed for two children of equal/close weights. Use with one

child may cause the unbalance condition which can injure/ harm your child.

• Purses, shopping bags, parcels, diaper bags or accessory items may change the balance of the stroller and cause hazardous unstable conditions.

• The maximum weight that can be carried in the basket is 5 lbs and in the parent tray is 3 lbs. The maximum weight can be carried in the side pockets (2) is 3 lbs, back pockets (2) is 3 lbs and canopy pockets is (2) 1 lb. Excessive weight may cause a hazardous unstable condition to exist.

• Be certain the stroller is fully erect and latched in the open position before allowing the children near the stroller.

• Use of the stroller with children weighing more than 50 pounds each (no more than 50 pounds per seat), or more than 100 pounds in total, or over 42 inches tall, will cause excessive wear and stress on the stroller and may cause a hazardous unstable condition to exist.

NEVER use the stroller on stairways or escalators.

•

NEVER use the stroller with roller skates, in-line skates, skateboards or bicycles.

•

• We recommend that the child occupant be at least 6 months of age prior to use of the stroller for jogging. Because children develop at different rates, please discuss the use of a jogging stroller with your health care provider prior to jogging with your child.

NEVER allow your stroller to be used as a toy.

•

• To clean use only mild household soap or detergent and warm water on a sponge or clean cloth.

• Check your stroller for loose screws, worn parts, torn material or stitching on a regular basis. Replace or repair parts as needed.

• Discontinue use of stroller should it malfunction or become damaged. Please contact our customer service Parts Hotline to arrange for repair or obtain replacement parts.

If you experience any difculty with the use of our product or have a question regarding these instructions, please contact our Customer Service Department at 1-800-328-7363 between the hours of 8:00 a.m. and 4:30 p.m. (PST). Please do not return the product to the store as once it is returned it cannot be re-sold and the materials and energy used to make it are wasted.

TYPE 1: FIXED FRONT WHEEL

Parent Tray

Screws

Stroller Fender

TYPE 2: SWIVEL FRONT WHEEL

Fender Screws

Parent Tray

Screws

Front Wheel

Type 1 Type 2

Rear Wheels

Stroller Fender

Fender Screws

Rear Wheels

Type 1

ASSEMBLY

IMPORTANT! To ensure safe operation of your stroller,

please follow these instructions carefully. Please keep these instructions for future reference.

IMPORTANT! Before assembly and each use, inspect this

product for damaged hardware, loose joints, missing parts or sharp edges. NEVER use if any parts are mssing or broken.

IMPORTANT! Adult assembly is required.

Skip to page 5 if you have Type 2

Swivel Front Wheel

Type 1: Fixed Front Wheel

Fig. 1

Remove stroller from box. The front wheel, rear wheels, fender, and parent tray need to be installed prior to use.

Fig. 2a

Fig. 2b

Fig. 3a

Fig. 3b

Slot

Retainer Plate

Ring

Fig. 3c

Loosen

Fork Plate

Lever

FRONT WHEEL

To attach the front wheel, unfold stroller as described in the section following:

• Lean the stroller backwards so that it rests on the handle and rear axle frame and the front wheel forks are pointing upward. (Fig. 1)

• The brake release lever must be in the open position. (Fig. 6)

• The front wheel features a quick release attachment system. The quick release must be open enough for the wheel to slide on the forks. Rotate the lever forward to loosen one side

(Fig. 2a) and loosen the nger nut on the other

side. (Fig. 2b)

• Slide the front wheel onto the front forks. (Fig. 3a) Make sure the front forks are in the position as shown on Fig. 3b.

• Line up the tab on the Retainer Plate with the Slot on both sides of the forks. (Fig. 3c)

IMPORTANT! The tab on the Retainer Plate must be lined up with the slot before tighten the wheel.

• With the wheel in position, tighten the

nger nut on the axle until it is very close

to contacting the fork and rotate the lever to tighten it as shown in Fig. 4.

• Close the lever (Fig. 5) and you should feel

signicant resistance and the wheel should

be held tightly. If you do not, open the lever

and tighten the nger nut a bit more and close

the lever again. Continue to do this until the wheel is held tightly in the fork.

DO NOT OVER TIGHTEN.

WARNING: Always make

sure the lever is in closed postion before use. Leaving the lever in opened postion can cause the wheel to fall off.

• Close the brake release lever by rotating it toward the front of the stroller. (Fig. 6).

FENDER

To secure the fender to the frame, use the 4 screws provided.

• Examine the bottom of the front fender. You will notice four 1/4 inch diameter plastic tubes protruding from the bottom (Fig. 7a).

• These tubes must be lined up with the holes in the front frame assembly (Fig. 7b).

• Line up the front fender and press onto the front frame assembly (Fig. 7c).

• Insert the 4 screws through the underside of the front frame assembly into the front fender's plastic tubes. Tighten the screws only until snug (Fig. 7d). NO NOT OVER-TIGHTEN.

Open

Tighten

Loosen

Fig. 4

Close Open

Fig. 5

Fig. 6

Fig. 7a

Fig. 7b

Fig. 7c

Fig. 7d

+ 5 hidden pages

BabyTrend 9165TW User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual