Axis P8513, P8514 Installation Manual
INSTALLATION GUIDE
AXIS P85 Network Camera Series
AXIS P8513 Network Camera
AXIS P8514 Network Camera
ENGLISH DEUTSCH
FRANÇAIS
ITALIANO
ESPAÑOL
Legal Considerations
Video and audio surveillance can be prohibited
by laws that vary from country to country. Check
the laws in your local region before using this
product for surveillance purposes.
This product includes one (1) H.264 decoder
license. To purchase further licenses, contact
your reseller.
Electromagnetic Compatibility (EMC)
This equipment generates, uses and can radiate
radio frequency energy and, if not installed and
used in accordance with the instructions, may
cause harmful interference to radio
communications. However, there is no
guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful
interference to radio or television reception,
which can be determined by turning the
equipment off and on, the user is encouraged to
try to correct the interference by one or more of
the following measures: Re-orient or relocate
the receiving antenna. Increase the separation
between the equipment and receiver. Connect
the equipment to an outlet on a different circuit
to the receiver. Consult your dealer or an
experienced radio/TV technician for help.
Shielded (STP) network cables must be used with
this unit to ensure compliance with EMC
standards. See “Electromagnetic Compatibility
(EMC)” on page 79 for more
information on this product’s compliance with
radio frequency and safety standards.
Equipment Modifications
This equipment must be installed and used in
strict accordance with the instructions given in
the user documentation. This equipment
contains no user-serviceable components.
Unauthorized equipment changes or
modifications will invalidate all applicable
regulatory certifications and approvals.
Liability
Every care has been taken in the preparation of
this document. Please inform your local Axis
office of any inaccuracies or omissions. Axis
Communications AB cannot be held responsible
for any technical or typographical errors and
reserves the right to make changes to the
product and documentation without prior
notice. Axis Communications AB makes no
warranty of any kind with regard to the material
contained within this document, including, but
not limited to, the implied warranties of
merchantability and fitness for a particular
purpose. Axis Communications AB shall not be
liable nor responsible for incidental or
consequential damages in connection with the
furnishing, performance or use of this material.
RoHS
This product complies with both the
European RoHS directive, 2002/95/EC,
and the Chinese RoHS regulations,
ACPEIP.
WEEE Directive
The European Union has enacted a
Directive 2002/96/EC on Waste
Electrical and Electronic Equipment
(WEEE Directive). This directive is
applicable in the European Union
member states.
The WEEE marking on this product
(see right) or its documentation indicates that
the product must not be disposed of together
with household waste. To prevent possible harm
to human health and/or the environment, the
product must be disposed of in an approved and
environmentally safe recycling process. For
further information on how to dispose of this
product correctly, contact the product supplier,
or the local authority responsible for waste
disposal in your area.
Business users should contact the product
supplier for information on how to dispose of
this product correctly. This product should not
be mixed with other commercial waste. For more
information, visit www.axis.com/techsup/
commercial waste
Support
Should you require any technical assistance,
please contact your Axis reseller. If your
questions cannot be answered immediately, your
reseller will forward your queries through the
appropriate channels to ensure a rapid response.
If you are connected to the Internet, you can:
• download user documentation and firmware
updates
• find answers to resolved problems in the FAQ
database; search by product, category, or
phrases
• report problems to Axis support by logging in
to your private support area.
AXIS P85 Network Camera Series Page 3
Safeguards
Please read through this Installation Guide carefully before installing the
product. Keep the Installation Guide for further reference.
CAUTION!
• When transporting the Axis product, use the original packaging or
equivalent to prevent damage to the product.
• Store the Axis product in a dry and ventilated environment.
• Only use handtools when installing the Axis product, the use of
electrical tools or excessive force could cause damage to the product.
• Do not use chemicals, caustic agents, or aerosol cleaners. Use a
damp cloth for cleaning.
• Only use accessories and spare parts provided or recommended by
Axis.
• Do not attempt to repair the product by yourself, contact Axis or
your Axis reseller for service matters.
IMPORTANT!
• This Axis product must be used in compliance with local laws and
regulations.
ENGLISH
AXIS P85 Network Camera Series Page 5
AXIS P85 Network Camera Series
Installation Guide
This installation guide provides instructions for installing AXIS P85
Network Camera Series. For all other aspects of using the product, please
see the user’s manual, available on www.axis.com/techsup
Installation steps
1. Check the package contents against the list below.
2. See Hardware overview. See page 6.
3. Install the hardware. See page 7.
4. Assign an IP address. See page 8.
5. Set the password. See page 11.
Package contents
Item Models/variants/notes
Network camera AXIS P8513, AXIS P8514
Accessories Clamps for wallmount 3 pcs
Height indicator decal
Important!
This product must be
used in compliance with
local laws and
regulations.
ENGLISH
Printed Materials AXIS P85 Network Camera Installation Guide (this
Optional accessories For a complete list of the available accessories, please
document), Axis Warranty Document
visit the Axis website at www.axis.com
Page 6 AXIS P85 Network Camera Series
Hardware overview
Upper pipe
Lower pipe
Height indicator
decal
Hole for
lens
Lens
Clamp
.
Control button
with rubber cap
AXIS P85 Network Camera Series Page 7
Install the hardware
Follow these instructions to attach the height indicator decal to the
pipe.
1. Find the lens hole by the 160/5ft marking on the decal and remove
the punch-out.
2. Carefully align the hole with the lens hole on the pipe and attach
the decal.
Follow these instructions to install the camera.
1. Attach the upper pipe to the lower pipe.
2. Place the pipe on the wall, with the lower end on the floor.
3. Attach the pipe to the
wall using the clamps.
4. Adjust the position of
the lens by rotating the
pipe.
5. Tighten the clamps to
secure the position of
the camera.
Note:
The lens is located in the
upper half of the pipe and is
at eye-level (160 cm, 5.3 ft).
283 cm
(9.3 ft)
ENGLISH
Page 8 AXIS P85 Network Camera Series
Assign an IP address
AXIS P85 Network Camera is designed for use on an Ethernet network
and requires an IP address for access. Most networks today have a DHCP
server that automatically assigns IP addresses to connected devices. If
your network does not have a DHCP server, the AXIS P85 Network
Camera will use 192.168.0.90 as the default IP address.
AXIS IP Utility and AXIS Camera Management are the recommended
methods for setting an IP address in Windows. These free applications
can be downloaded from www.axis.com/techsup Depending on the
number of cameras you wish to install, use the method that suits you
best.
Method Recommended for Operating system
AXIS IP Utility
See page 9
AXIS Camera
Management
See page 10
Single camera
Small installations
Multiple cameras
Large installations
Installation on a
different subnet
Windows
Windows 7
Windows Vista
Windows 2000
Windows XP Pro
Windows 2003
Server
Notes:
• If you are unable to set the IP address, check for any firewall blocking the
operation.
• For other methods of assigning or discovering the IP address, such as in other
operating systems, see page 13.
AXIS P85 Network Camera Series Page 9
AXIS IP Utility - single camera/small installation
AXIS IP Utility
automatically discovers and
displays Axis devices on
your network. You can also
manually set a static IP
address through this
application. AXIS IP Utility
can be downloaded from
www.axis.com/techsup
Note that you must install the network camera on the same network
segment (physical subnet) as the computer running AXIS IP Utility.
Automatic discovery
1. Check that the network camera is connected to the network and
that power has been applied.
2. Start AXIS IP Utility.
3. When the camera appears in the window, double-click it to open its
home page.
4. See page 11 for instructions on how to assign the password.
Assign the IP address manually (optional)
1. Acquire an unused IP address on the same network segment as your
computer.
2. Select AXIS P8513/AXIS P8514 in the list.
3. Click the button Assign new IP address to selected device and
enter the IP address.
4. Click the Assign button and follow the instructions.
5. Click the Home Page button to access the camera’s web pages.
6. See page 11 for instructions on how to set the password.
ENGLISH
Page 10 AXIS P85 Network Camera Series
AXIS Camera Management - multiple cameras/large
installations
AXIS Camera Management can automatically discover multiple Axis
devices, show connection status, manage firmware upgrades, and set IP
addresses.
Automatic discovery
1. Check that the camera is connected to the network and that power
has been applied.
2. Start AXIS Camera Management. When the camera appears in the
window, right-click the link and select Live View Home Page.
3. See page 11 for instructions on how to set the password.
Assign an IP address in a single device
1. Select one of the AXIS P85 Network Camera in AXIS Camera
Management and click the Assign IP button .
2. Select Assign the following IP address and enter the IP address, the
subnet mask, and default router the device will use.
3. Click OK.
AXIS P85 Network Camera Series Page 11
Assign IP addresses in multiple devices
AXIS Camera Management speeds up the process of assigning IP
addresses to multiple devices, by suggesting IP addresses from a
specified range.
1. Select the devices you wish to configure (different models can be
selected) and click the Assign IP button .
2. Select Assign the following IP address range and enter the range
of IP addresses, the subnet mask, and default router the devices will
use.
3. Click OK.
Set the password
To gain access to the product, the password for the default
administrator user root must be set. This is done in the Configure Root
Password dialog, which is displayed when the network camera is
accessed for the first time.
To prevent network eavesdropping when setting the root password, this
can be done via an encrypted HTTPS connection, which requires an
HTTPS certificate.
To set the password via a standard HTTP connection, enter it in the
Configure Root Password window.
To set the password via an encrypted HTTPS connection, follow these
steps:
1. Click the Create self-signed certificate button.
2. Provide the requested information and click OK. The certificate is
created and the password can now be set securely. All traffic to and
from the network camera is encrypted from this point on.
ENGLISH
Page 12 AXIS P85 Network Camera Series
3. Enter a password and then re-enter it to confirm the spelling. Click
OK. The password has now been configured.
To create an HTTPS connection,
start by clicking this button.
To configure the password directly
via an unencrypted connection,
enter the password here.
4. To log in, enter the user name “root” in the dialog as requested.
Note: The default administrator user name root cannot be deleted.
5. Enter the password as set above, and click OK. If the password is
lost, the network camera must be reset to the factory default
settings. See page 14.
If required, click Yes to install AMC (AXIS Media Control), which allows
viewing of the video stream in Internet Explorer. You will need
administrator rights on the computer to do this.
The Live View page of the network camera appears. The Setup link to the
right gives you menu options for customizing the camera.
AXIS P85 Network Camera Series Page 13
Other methods of setting the IP address
AVHS Service
Connection
UPnP™
Bonjour
AXIS Dynamic
DNS Service
ARP/Ping
DHCP
Use in
operating
system
All To connect the camera to an AVHS service,
Windows
(ME or
XP)
MAC OSX
(10.4 or
later)
All A free service from Axis that allows you to
All See user’s manual. The command must be
All To view the admin pages for the network
Notes
refer to the service provider´s Installation
guide. For information and help to find a
local AVHS Service Provider go to
www.axis.com
When enabled on your computer, the camera
is automatically detected and added to “My
Network Places.”
Applicable to browsers with support for
Bonjour. Navigate to the Bonjour bookmark
in your browser (e.g. Safari) and click on the
link to access the camera’s web pages.
quickly and simply install your camera.
Requires an Internet connection with no HTTP
proxy. See www.axiscam.net for more
information.
issued within 2 minutes of connecting power
to the camera.
DHCP server, see the server’s documentation.
ENGLISH
Page 14 AXIS P85 Network Camera Series
Resetting to the Factory Default Settings
This will reset all parameters, including the IP address, to the Factory
Default settings:
1. Disconnect the network cable.
2. Remove the rubber cap from the control button hole.
3. Using an appropriate object such as a small screw driver, press and
hold the Control button and reconnect the network cable.
4. Keep the Control button pressed for at least 15 seconds.
5. Release the Control button.
6. Wait for at least 1 minute for the process to complete.
7. The camera has now been reset.
8. Re-assign the IP address, using one of the methods described in this
document.
It is also possible to reset parameters to the original factory default
settings via the web interface. For more information, please see the
online help or the user’s manual.
Further information
The user’s manual is available from the Axis Web site at www.axis.com.
Tip!
Visit www.axis.com/techsup to check if there is updated firmware
available for your network camera. To see the currently installed
firmware version, click the Basic Configuration menu item in the
product’s web page.
AXIS P85 Network Camera Series Page 15
Mesures de sécurité
Lisez attentivement le présent guide d’installation avant d’installer le
produit. Conservez le guide d’installation si vous souhaitez le consulter
ultérieurement.
ATTENTION !
• Pour éviter d’endommager le produit Axis, utilisez l’emballage
d’origine ou un équivalent pour le transporter.
• Stockez le produit Axis dans un environnement sec et aéré.
• Utilisez uniquement des outils manuels pour l’installation du produit
Axis, l’utilisation d’outils électriques ou l’usage excessif de la force
risque de l’endommager.
• N’utilisez ni produits chimiques, ni substances caustiques, ni
nettoyeurs aérosol. Utilisez un linge humide pour le nettoyage.
• Utilisez uniquement des accessoires et des pièces de rechange
fournis ou recommandés par Axis.
• Ne tentez pas de réparer le produit vous-même, contactez Axis ou
votre revendeur Axis pour tout problème lié au service.
IMPORTANT !
• Ce produit Axis doit être utilisé conformément aux lois et
réglementations locales en vigueur.
FRANÇAIS
Page 16 AXIS P85 Network Camera Series
Série des caméras réseau AXIS P85 Page 17
Série des caméras réseau AXIS P85
Guide d’installation
Ce guide d’installation vous explique comment installer la Série des
caméras réseau AXIS P85. Pour toute autre question concernant
l’utilisation du produit, reportez-vous au manuel de l’utilisateur que vous
trouverez sur le site www.axis.com/techsup.
Procédure d’installation
1. Vérifiez le contenu de l’emballage par rapport à la liste ci-dessous.
2. Description du matériel, à la page 18.
3. Installation du matériel, à la
page 19.
4. Attribution d’une adresse IP, à la
page 20
5. Configuration du mot de passe, à la
page 25.
Contenu de l’emballage
Élément Modèles/variantes/remarques
Caméra réseau AXIS P8513, AXIS P8514
Accessoires Pinces pour le montage mural, 3 pièces
Important !
Ce produit doit être
utilisé conformément
aux lois et
réglementations locales
en vigueur.
FRANÇAIS
Documentation
imprimée
Accessoires en
option
Étiquette autocollante d’indicateur de hauteur
Guide d’installation de la Caméra réseau AXIS P85 (le
présent document), document de garantie Axis
Pour obtenir une liste complète des accessoires
disponibles, consultez le site Web d’Axis,
www.axis.com
Page 18 Série des caméras réseau AXIS P85
Présentation du matériel
Tube supérieur
Étiquette autocollante
d’indicateur de hauteur
Tube inférieur
Trou pour
l’objectif
Objectif
Collier
.
Bouton de
commande
avec capuchon
en caoutchouc
Série des caméras réseau AXIS P85 Page 19
Installation du matériel
Procédez comme suit pour coller l’étiquette autocollante d’indicateur de
hauteur au tube.
1. Repérez le trou de l’objectif en vous reportant à la marque 160/5ft
de l’étiquette autocollante et retirez la perforation.
2. Alignez soigneusement le trou sur le trou de l’objectif se trouvant
sur le tube et collez l’étiquette.
Procédez comme suit pour installer la caméra.
1. Fixez le tube supérieur au tube inférieur.
2. Placez le tube sur le mur, en positionnant l’extrémité inférieure sur
le sol.
3. Fixez le tube au mur à
l’aide des colliers.
4. Ajustez la position de
l’objectif en faisant
tourner le tube.
5. Serrez les colliers pour
bien fixer la caméra.
Remarque :
L’objectif se trouve dans la
moitié supérieure du tube et à
la hauteur des yeux (160 cm,
5,3 pieds).
283 cm
(9,3 pi)
FRANÇAIS
Page 20 Série des caméras réseau AXIS P85
Attribution d’une adresse IP
La Caméra réseau AXIS P85 est conçue pour une utilisation sur un réseau
Ethernet et nécessite une adresse IP pour y accéder. Aujourd’hui, la
plupart des réseaux sont équipés d’un serveur DHCP qui attribue
automatiquement des adresses IP aux périphériques connectés. Si votre
réseau en est dépourvu, la Caméra réseau AXIS P85 utilisera
192.168.0.90 comme adresse IP par défaut.
Si vous souhaitez définir une adresse IP sous Windows, nous vous
recommandons d’utiliser l’application AXIS IP Utility ou
AXIS Camera Management. Ces applications gratuites peuvent être
téléchargées à partir du site www.axis.com/techsup. Choisissez la
méthode qui vous convient le mieux en fonction du nombre de caméras
à installer.
Méthode Recommandée pour Système
AXIS IP Utility
Voir page 21
AXIS Camera
Management
Voir page 23
Caméra unique
Petites installations
Plusieurs caméras
Grandes installations
Installation sur un
autre sous-réseau
d’exploitation
Windows
Windows 7
Windows Vista
Windows 2000
Windows XP Pro
Windows 2003
Server
Remarques :
• Si vous n’arrivez pas à configurer l’adresse IP, vérifiez qu’aucun pare-feu ne
bloque l’opération.
• Pour connaître les autres méthodes d’attribution ou de détection de l’adresse IP,
par exemple sous d’autres systèmes d’exploitation, reportez-vous à la page 28.
Série des caméras réseau AXIS P85 Page 21
AXIS IP Utility - Caméra unique et petite installation
AXIS IP Utility recherche et
affiche automatiquement
les périphériques Axis
présents sur votre réseau.
Cette application permet
également de définir
manuellement une
adresse IP statique.
Lapplication AXIS IP Utility peut être téléchargée à partir du site
www.axis.com/techsup
Notez que vous devez installer la caméra réseau sur le même segment de
réseau (sous-réseau physique) que l’ordinateur exécutant l’application
AXIS IP Utility.
Détection automatique
1. Vérifiez que la caméra réseau est connectée au réseau et qu’elle est
sous tension.
2. Lancez AXIS IP Utility.
3. Lorsque l’icône de la caméra apparaît dans la fenêtre, cliquez deux
fois dessus pour ouvrir la page d’accueil correspondante.
4. Reportez-vous à la page 25 pour la configuration du mot de passe.
Attribution manuelle de l’adresse IP (facultatif)
1. Trouvez une adresse IP non utilisée sur le même segment de réseau
que celui de votre ordinateur.
2. Sélectionnez AXIS P8513/AXIS P8514 dans la liste.
3. Cliquez sur le bouton Assign new IP address to selected device
(Attribuer une nouvelle adresse IP au périphérique sélectionné) et
saisissez l’adresse IP.
4. Cliquez sur le bouton Assign (Attribuer) et suivez les instructions.
FRANÇAIS
Page 22 Série des caméras réseau AXIS P85
5. Cliquez sur le bouton Home Page (Page d’accueil) pour accéder aux
pages Web de la caméra.
6. Reportez-vous à la page 25 pour la configuration du mot de passe.
Série des caméras réseau AXIS P85 Page 23
AXIS Camera Management - plusieurs
caméras/grandes installations
AXIS Camera Management peut détecter automatiquement plusieurs
périphériques Axis, afficher leur état de connexion, gérer les mises à
niveau du micrologiciel et configurer les adresses IP.
Détection automatique
1. Vérifiez que la caméra est connectée au réseau et qu’elle est sous
tension.
2. Lancez AXIS Camera Management. Lorsque l’icône de la caméra
apparaît dans la fenêtre, cliquez sur le lien à l’aide du bouton droit
de la souris et sélectionnez Live View Home Page (Page d’accueil –
Vidéo en direct).
3. Reportez-vous à la page 25 pour la configuration du mot de passe.
Attribution d’une adresse IP à un seul périphérique
1. Sélectionnez l’une des caméras de la Caméra réseau AXIS P85 dans
l’application AXIS Camera Management, puis cliquez sur le bouton
Assign IP (Attribuer une adresse IP).
FRANÇAIS
Page 24 Série des caméras réseau AXIS P85
2. Sélectionnez Assign the following IP address (Attribuer l’adresse IP
suivante) et saisissez l’adresse IP, le masque de sous-réseau et le
routeur par défaut que le périphérique utilisera.
3. Cliquez sur OK.
Loading...