Axis 5026-401 User Manual

INSTALLATION GUIDE
AXIS T8640 Ethernet Over Coax Adaptor PoE+
ENGLISH DEUTSCH
FRAN
Ç AIS
ITALIANO
ESPAÑOL
Electromagnetic Compatibility (EMC)
This equipment has been designed and tested to fulfill applicable standards for:
• Radio frequency emission when installed according to the instructions and used in its intended environment.
• Immunity to electrical and electromagnetic phenomena when installed according to the instructions and used in its intended environment.
USA - This equipment has been tested using a
shielded network cable (STP) and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Europe - This digital equipment fulfills
the requirements for RF emission according to the Class A limit of EN 55022 when DC powered. NOTICE! This is a Class A product. In a domestic environment this product may cause RF interference, in which case the user may be required to take adequate measures.
Europe - This digital equipment fulfills
the requirements for RF emission according to the Class B limit of EN 55022 when PoE powered.
This product fulfills the requirements for immunity according to EN 55024 office and commercial environments.
Canada - This Class A digital apparatus
complies with Canadian ICES-003 when DC powered.
Canada - This Class B digital apparatus
complies with Canadian ICES-003 when PoE powered.
Australia - This digital equipment fulfills the
requirements for RF emission according to the Class A limit of AS/NZS CISPR 22 when DC powered. NOTICE! This is a class A product. In a domestic environment this product may cause RF interference, in which case the user may be required to take adequate measures.
Australia - This digital equipment fulfills the
requirements for RF emission according to the Class B limit of AS/NZS CISPR 22 when PoE powered.
Equipment Modifications
This equipment must be installed and used in strict accordance with the instructions given in the user documentation. This equipment contains no user-serviceable components. Unauthorized equipment changes or modifications will invalidate all applicable regulatory certifications and approvals.
Liability
Every care has been taken in the preparation of this document. Please inform your local Axis office of any inaccuracies or omissions. Axis Communications AB cannot be held responsible for any technical or typographical errors and reserves the right to make changes to the product and documentation without prior notice. Axis Communications AB makes no warranty of any kind with regard to the material contained within this document, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Axis Communications AB shall not be liable nor responsible for incidental or consequential damages in connection with the furnishing, performance or use of this material.
RoHS
This product complies with both the European RoHS directive, 2002/95/EC, and the Chinese RoHS regulations, ACPEIP.
WEEE Directive
The European Union has enacted a Directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE Directive). This directive is applicable in the European Union member states. The WEEE marking on this product (see right) or its documentation indicates that the product must not be disposed of together with household waste. To prevent possible harm to human health and/or the environment, the product must be disposed of in an approved and environmentally safe recycling process. For further information on how to dispose of this product correctly, contact the product supplier, or the local authority responsible for waste disposal in your area. Business users should contact the product supplier for information on how to dispose of this product correctly. This product should not be mixed with other commercial waste. For more information, visit www.axis.com/techsup/.
Support
Should you require any technical assistance, please contact your Axis reseller. If your questions cannot be answered immediately, your reseller will forward your queries through the appropriate channels to ensure a rapid response. If you are connected to the Internet, you can:
• download user documentation and software updates
• find answers to resolved problems in the FAQ database. Search by product, category, or phrase
• report problems to Axis support staff by logging in to your private support area
• chat with Axis support staff (selected countries only)
• visit Axis Support at www.axis.com/techsup/
AXIS T8640 Page 5
Device unit
Base unit
Network connector
Power
BNC connector
LEDs
connector
LEDs
AXIS T8640 Ethernet Over Coax Adaptor
PoE+ Installation Guide
Package Contents
Item Models/variants/notes
Ethernet Over Coax Adaptor PoE+
Optional accessories
Printed Materials AXIS T8640 Installation Guide (this document)
AXIS T8640:
• AXIS T8641 Ethernet Over Coax Base Unit PoE+
• AXIS T8642 Ethernet Over Coax Device Unit PoE+
AXIS T8003 PS57 (Power supply) DIN Rail clip Wall bracket Rack mount bracket
Hardware Overview
ENGLISH
Page 6 AXIS T8640
Ethernet
switch
switch
Power supply (optional)
Base unit
Device unit
Device unit
Device unit
Device unit
Base unit
Base unit
Base unit
PoE switch
Midspan
Base unit
Device unit
Power supply
Power supply
Ethernet
Hardware Overview - Configuration Examples
Example 4. PoE devices higher than class 4 require additional midspan.
Example 2. External power supply needed when used together with non-PoE switch.
Example 3. PoE powered solution (optional power supply needed when used together with low quality cables)
PoE
Example 1. External power supply needed when used together with non-PoE switch.
switch
AXIS T8640 Page 7
LED Indicators
LED Behavior/color Indication
Coax link
Ethernet link
PoE over coax
Max PoE power available for camera (Watts)
Off No power
On Connection established
Flash Units not detected on coax
Orange/red Data rate < 100%. The coax connection has
Off No network connection
On Ethernet link established
Flash Network activity on port
Red 10BASE-T connection. Units must be connected
Off Units not detected
On PoE over Coax enabled
Red (1 flash) Low voltage. Check power supply type/polarity.
Red (2 flashes) Short circuit. Check for cable faults and remove
Red (3 flashes) Power disconnected due to overload.
On Max PoE power that can be reliably delivered
Flash Less than 5 watts of PoE available.
Orange (flashing) Approaching power limit
Red (flashing) Power limit reached. See note below.
reached power and range limit. Reduce cable distance or connect an AXIS T8003 PS57 supply to the Device unit.
to 100BASE-T (full-duplex) compatible equipment for effective operation.
legacy video equipment.
from 5 to 25 watts.
ENGLISH
Page 8 AXIS T8640
Note:
• Available power is specific to the cable length, type, and power source used, and is calculated automatically on connection. For example, to ensure reliable power delivery to a PoE IP camera whose maximum power requirement is 12 watts, check that the 15 watt LED is lit.
• If installing a PTZ camera, or any equipment whose power requirement can change, check these LEDs while the equipment is drawing peak power, such as when the PTZ camera is moving.
• For maximum PoE over coax power, connect an AXIS T8003 PS57 power supply to the Base unit. If more power is required than the cable can carry, the power supply can be connected to the Device unit.
AXIS T8640 Page 9
Technical Specifications
Item
Model AXIS T8640:
Data rate Coaxial cable: 100Mbps Full Duplex
Connectors Coaxial: BNC 75 Ohm
Network cables • Coaxial: Any 75 Ohm coaxial (other impedances supported),
Output power AXIS T8641: PoE over Coax with safe auto-detection and
Input power • AXIS T8641: PoE (IEEE 802.3at Class 4 powered device) or
Installation/ management
Compliance IEEE 802.3at, IEEE 802.3af, RoHS, WEEE, CE
Mounting Wall, rack, DIN Rail
Environment Indoor
Specifications
• AXIS T8641 Ethernet Over Coax Base Unit PoE+
• AXIS T8642 Ethernet Over Coax Device Unit PoE+
Ethernet cable: 100Base-TX Full Duplex
Ethernet: Shielded RJ-45, EIA 568A and 568B
to 500 m /1600 ft. at full rate
• Ethernet: Shielded category 5 (or higher); (patch or cross­over, auto-detected)
autocutout AXIS T8642: PoE (IEEE 802.3af/at) enabled to detected devices up to 25.5 W
DC power supply
• AXIS T8642: PoE over Coax or DC power supply
• DC Power supply: AXIS T8003 PS57 or 44 - 56V DC Class 2 isolated supply (max 0.7 amps)
• Device power: 1.5 W
Plug-and-play installation; automatically detects PoE and High PoE-enabled devices and supplies in-line power Local LED management display
ENGLISH
Page 10 AXIS T8640
Item
Approvals FCC part 15, Class B with FTP cabling
Operating conditions
Storage -40 °C to 74 °C (-40 °F to 165 °F)
Dimension (HxWxD)
Weight 140 g (0.3 lbs)
Optional accessories
Specifications
EN 55022 Class B (Emissions, PoE powered) EN 55022 Class A (Emissions, DC powered) EN 55024 (Immunity)
-10 °C to 50 °C (14 °F to 122 °F) Humidity max. 95% RH (non-condensing)
104 x 54 x 24 mm (4.1” x 2.1” x 0.9)
AXIS T8003 PS57 Power supply, DIN Rail Clip, Wall Mount Bracket, Rack Mount Bracket
AXIS T8640 Page 11
Examples of Power Source for:
Low power PoE Network cameras (PoE IEEE 802.3af Class 1, or 2; < 6 watts)
• AXIS M11 Network Camera Series
• AXIS 221 Network Camera
• AXIS M30 Network Camera Series
• AXIS M32 Network Camera Series
• AXIS M31-R/VE Network Camera Series
• AXIS P33 Network Cameras (indoor models)
• AXIS 212 PTZ/-V Network Camera
Using an 802.3af PoE switch Using AXIS T8003 PS57
150m (492 ft.) of CCS RG-59 350m (1148 ft.) of CC RG-59 400m (1312 ft.) of CC RG-6 500m (1640 ft.) of CC RG-11
Note:
CC = Copper-Cored Cable (most common for correctly installed analog video) CCS = 22AWG Copper-Coated Steel (shows worst-case perfor­mance if cable type is not known)
280m (919 ft.) of CCS RG-59 350m (1148 ft.) of CC RG-59 400m (1312 ft.) of CC RG-6 500m (1640 ft.) of CC RG-11
ENGLISH
Page 12 AXIS T8640
Examples of Power Source for:
Medium power PoE Network cameras (PoE IEEE 802.3af Class 1, 2 or 3; <10 watts)
• AXIS M1054 Network Camera
• AXIS P13 Network Cameras (indoor models)
• AXIS Q16 Network Cameras (indoor models)
• AXIS Q1755 Network Camera
• AXIS Q19 Network Camera Series
• AXIS P33-VE Network Cameras
Using an 802.3af PoE switch Using AXIS T8003 PS57
CCS RG-59 not supported 350m (1148 ft.) of CC RG-59 400m (1312 ft.) of CC RG-6 500m (1640 ft.) of CC RG-11
Examples of Power Source for:
Full power PoE or PoE+ Network cameras (PoE IEEE 802.3af Class 3; >10 watts) or IEEE 802.3at.
• AXIS P13-E Network Cameras
• AXIS Q16-E Network Cameras
• AXIS Q1755-E Network Camera
• AXIS P55 Network Camera Series
• AXIS Q60 Network Cameras (indoor models)
200m (656 ft.) of CCS RG-59 350m (1148 ft.) of CC RG-59 400m (1312 ft.) of CC RG-6 500m (1640 ft.) of CC RG-11
Using an 802.3af PoE switch Using AXIS T8003 PS57
Not supported 80m (262 ft.) of CCS RG-59
350m (1148 ft.) of CC RG-59 400m (1312 ft.) of CC RG-6 500m (1640 ft.) of CC RG-11
AXIS T8640 Page 13
Examples of Power Source for:
Custom High PoE Network cameras that use AXIS T8124 High PoE 60 W Midspan 1-port such as the AXIS Q60-E Network Cameras.
Using an 802.3af PoE switch Using AXIS T8003 PS57
PoE to the camera is not supported. The AXIS T8642 Device can be powered over the coaxial cable, but an AXIS T8124 60 W midspan must be used to power the camera locally.
Note:
• The actual range depends on several factors such as cable quality, cable
thickness, connectors and camera power consumption.
• Range figures assume short (<5 m or 16 ft.) Cat-5e cables between equipment.
• CC - Copper-Cored Cable (most common for correctly installed analog video)
CCS - 22AWG Copper-Coated Steel (shows worst-case performance if cable type is not known)
Warranty
For information about Axis' product warranty and thereto related information, see www.axis.com/warranty
ENGLISH
AXIS T8640 Page 15
Adaptateur Ethernet sur câble coaxial avec
PoE+ AXIS T8640 Guide d’installation
Contenu de l’emballage
Élément Modèles/variantes/remarques
Adaptateur Ethernet sur câble coaxial avec PoE+
Accessoires en option
Documentation imprimée
AXIS T8640:
• Unité de base Ethernet sur câble coaxial avec PoE+ AXIS T8641
• Périphérique Ethernet sur câble coaxial avec PoE+ AXIS T8642
AXIS T8003 PS57 (Bloc d’alimentation) Clip pour rail DIN Support mural Support de fixation sur rack
AXIS T8640 Guide d’installation (le présent document)
FRAN
Ç AIS
Page 16 AXIS T8640
Périphérique
Unité de base
Connecteur réseau
Voyant
Connecteur BNC
Voyants DEL
connecteur
Voyants DEL
Présentation du matériel
AXIS T8640 Page 17
Ethernet
commutateur
Alimentation (en option)
Unité de base
Périphérique
Périphérique
Périphérique
Périphérique
Unité de base
Unité de base
Unité de base
Alimentation par Ethernet (PoE)
commutateur
Injecteur
Unité de base
Périphérique
Bloc d’alimentation
Bloc d’alimentation
Ethernet
Présentation du matériel - Exemples de configuration
Exemple 4. Les périphériques PoE supérieurs à la classe 4 nécessitent un autre injecteur.
Exemple 2. Alimentation électrique externe nécessaire en cas d'utilisation avec un commutateur non PoE.
Exemple 3. Solution d'alimentation PoE (alimentation en option nécessaire en cas d'utilisation avec des câbles de mauvaise qualité)
Alimentation par Ethernet (PoE) commutateur
Exemple 1. Alimentation électrique externe nécessaire en cas d'utilisation avec un commutateur non PoE.
commu­tateur
FRAN
Ç AIS
Page 18 AXIS T8640
Voyants lumineux
Voyant DEL
Liaison coaxiale
Liaison Ethernet
PoE par câble coaxial
Comportement/ couleur
Désactivé Pas d'alimentation
Activé Connexion établie
Clignotement Unités non détectées sur câble coaxial
Orange/rouge Débit de données < 100 %. La connexion du
Désactivé Pas de connexion au réseau.
Activé Liaison Ethernet établie
Clignotement Activité réseau sur un port
Rouge Connexion 10BASE-T. Les unités doivent être
Désactivé Unités non détectées
Activé PoE activée par câble coaxial
Rouge (clignote 1 fois)
Rouge (clignote 2 fois)
Rouge (clignote 3 fois)
Indication
câble coaxial a atteint la limite de plage et d'alimentation. Réduire la longueur du câble ou connecter une alimentation AXIS T8003 PS57 au périphérique.
connectées à un équipement compatible avec la norme 100BASE-T (duplex intégral) pour un fonctionnement efficace.
Basse tension. Vérifier la polarité/le type d'alimentation.
Court-circuit. Vérifier les défauts de câbles et enlever l'ancien équipement vidéo.
Interruption d'alimentation due à une surcharge.
AXIS T8640 Page 19
Voyant DEL
Alimentati on PoE maximale disponible pour caméra (en Watts)
Comportement/ couleur
Activé Alimentation PoE maximale pouvant être
Clignotement Moins de 5 watts de PoE disponibles.
Orange (clignotant)
Rouge (clignotant) Limite d'alimentation atteinte. Voir la
Indication
fournie de manière fiable de 5 à 25 watts.
Proche de la limite d'alimentation
remarque ci-dessous.
Remarque :
• L'alimentation disponible dépend du type et de la longueur du câble ainsi que de la source d'alimentation utilisée, et elle est calculée automatiquement lors de la connexion. Par exemple, pour être sûr qu'une caméra réseau PoE dont la puissance consommée est de 12 W maximum disposera d'un approvisionnement en électricité fiable, vérifiez que le voyant DEL 15 W est allumé.
• En cas d'installation d'une caméra PTZ (panoramique/inclinaison/zoom), ou de tout équipement dont la puissance consommée peut varier, vérifiez l'état de ces voyants LED au moment où les dispositifs consomment le plus de courant, comme lorsque la caméra PTZ est en mouvement.
• Pour une alimentation PoE maximum par câble coaxial, connectez une alimentation AXIS T8003 PS57 à l'unité de base. S'il faut plus de courant que le câble ne peut en transmettre, l'alimentation peut être connectée au périphérique.
FRAN
Ç AIS
Page 20 AXIS T8640
Caractéristiques techniques
Élément
Modèle AXIS T8640:
Débit de données
Connecteurs Câble coaxial: BNC 75 ohms
Câbles réseau • Câble coaxial: N'importe quel câble coaxial 75 ohms (autres
Sortie alimentation
Puissance d'entrée
Installation/ gestion
Caractéristiques techniques
• Unité de base Ethernet sur câble coaxial avec PoE+ AXIS T8641
• Périphérique Ethernet sur câble coaxial avec PoE+ AXIS T8642
Câble coaxial: Duplex intégral 100 Mb/s Câble Ethernet: 100 Base-TX duplex intégral
Ethernet: Câble RJ-45 blindé, normes EIA 568A et 568B
impédances prises en charge), à 500 m/1 600 pi à plein débit.
• Ethernet: Blindé catégorie 5 (ou supérieure); (câble droit ou croisé, détecté automatiquement).
AXIS T8641: PoE par câble coaxial avec sécurité de détection et de coupure automatique AXIS T8642: PoE (IEEE 802.3af/at) activée pour périphériques détectés jusqu'à 25,5 W
• AXIS T8641: Alimentation par Ethernet ou PoE (périphérique électrique conforme IEEE 802.3at de Classe 4) ou alimentation CC
• AXIS T8642: Alimentation par Ethernet par câble coaxial ou alimentation CC
• Alimentation CC: AXIS T8003 PS57 ou alimentation isolée 44 à 56 V CC classe 2 (max 0,7 amp)
• Alimentation du périphérique: 1,5 W
Installation plug-and-play (prête à l'emploi); détecte automatiquement les périphériques PoE et High PoE et fournit une alimentation en ligne. Affichage de la gestion des voyants DEL locaux
AXIS T8640 Page 21
Élément
Conformité IEEE 802.3at, IEEE 802.3af, RoHS, WEEE, CE
Support Rail DIN, en rack ou mural
Environnement Intérieur
Approbations FCC partie 15, classe B avec câblage FTP
Conditions d’utilisation
Stockage De -40 à 74 °C (de -40 °F à 165 °F)
Dimension (H x L x P)
Poids 140 g
Accessoires en option
Caractéristiques techniques
EN 55022 classe B (Émissions, alimentation électrique par câble Ethernet) EN 55022 classe A (Émissions, alimentation électrique CC) EN 55024 (Immunité)
De -10 °C à 50 °C (de 14 °F à 122 °F) Humidité maximale relative de 95 % (sans condensation)
104 x 54 x 24 mm (4,1 x 2,1 x 0,9 po)
AXIS T8003 PS57 Alimentation, clip pour rail DIN, montage mural Support, support de fixation sur rack
FRAN
Ç AIS
Page 22 AXIS T8640
Exemples de source d'alimentation pour:
Caméras réseau PoE faible puissance (PoE IEEE 802.3af Classe 1 ou 2; < 6 watts)
• Série des caméras réseau AXIS M11
• Caméra réseau AXIS 221
• Série des caméras réseau AXIS M30
• Série des caméras réseau AXIS M32
• Série des caméras réseau AXIS M31-R/VE
• Série des caméras réseau AXIS P33 (modèles d'intérieur)
• Caméra réseau AXIS 212 PTZ/-V
Avec commutateur PoE conforme à la norme 802.3af
150 m (492 pi.) de câble CCS RG-59 350 m (1148 pi.) de câble CC RG-59 400 m (1312 pi.) de câble CC RG-6 500 m (1640 pi.) de câble CC RG-11
Remarque :
installation analogique correct) CCS = Acier cuivré 22 AWG (affiche les pires performances si le type de câble n'est pas connu)
CC = Câblage cuivre (Le plus fréquemment utilisé pour une
Avec AXIS T8003 PS57
280 m (919 pi.) de câble CCS RG-59 350 m (1148 pi.) de câble CC RG-59 400 m (1312 pi.) de câble CC RG-6 500 m (1640 pi.) de câble CC RG-11
AXIS T8640 Page 23
Exemples de source d'alimentation pour:
Caméras réseau PoE moyenne puissance (PoE IEEE 802.3af classe 1, 2 ou 3; < 10 watts)
• Caméra réseau AXIS M1054
• Série des caméras réseau AXIS P13 (modèles d'intérieur)
• Caméras réseau AXIS Q16 (modèles d'intérieur)
• Caméra réseau AXIS Q1755
• Série des caméras réseau AXIS Q19
• Caméras réseau AXIS P33-VE
Avec commutateur PoE conforme à la norme 802.3af
Câble CCS RG-59 non supporté 350 m (1148 pi.) de câble CC RG-59 400 m (1312 pi.) de câble CC RG-6 500 m (1640 pi.) de câble CC RG-11
Exemples de source d'alimentation pour:
Caméras réseau PoE ou PoE+ pleine puissance (PoE IEEE 802.3af classe 3; > 10 watts) ou conformes à la norme IEEE 802.3at.
• Cameras réseau AXIS P13-E
• Caméras réseau AXIS Q16-E
• Caméra réseau AXIS Q1755-E
• Série des caméras réseau AXIS P55
• Caméras réseau AXIS Q60 (modèles d'intérieur)
Avec commutateur PoE conforme à la norme 802.3af
Non pris en charge 80 m (262 pi.) de câble CCS RG-59
Avec AXIS T8003 PS57
200 m (656 pi.) de câble CCS RG-59 350 m (1148 pi.) de câble CC RG-59 400 m (1312 pi.) de câble CC RG-6 500 m (1640 pi.) de câble CC RG-11
Avec AXIS T8003 PS57
350 m (1148 pi.) de câble CC RG-59 400 m (1312 pi.) de câble CC RG-6 500 m (1640 pi.) de câble CC RG-11
FRAN
Ç AIS
Page 24 AXIS T8640
Exemples de source d'alimentation pour:
Caméras réseau High PoE personnalisées utilisant un injecteur High PoE 60 W AXIS T8124 à 1 port, comme les caméras réseau AXIS Q60-E.
Avec commutateur PoE conforme à la norme 802.3af
L'alimentation par Ethernet de la caméra n'est pas prise en charge. Le périphérique AXIS T8642 peut être alimenté par câble coaxial, mais il faut utiliser un injecteur AXIS T8124 60 W pour alimenter localement la caméra.
Avec AXIS T8003 PS57
Remarque :
• La véritable portée dépend de plusieurs facteurs comme la qualité et l'épaisseur du câble, les connecteurs et la consommation électrique de la caméra.
• Des câbles courts de catégorie 5 (<5 m ou 16 pi.) sont à prévoir entre les équipements si l'on s'en réfère aux données relatives aux portées.
• CC = Câblage cuivre (Le plus fréquemment utilisé pour une installation analogique correct) CCS = Acier cuivré 22 AWG (affiche les pires performances si le type de câble n'est pas connu)
Garantie
Pour plus d'informations sur la garantie des produits Axis et des informations générales relatives à celle-ci de consulter le site www.axis.com/warranty
AXIS T8640 Seite 25
Geräteeinheit
Basiseinheit
Netzwerkanschluss
Netz-
BNC-Anschluss
LEDs
anschluss
LEDs
AXIS T8640 Ethernet Over Coax Adaptor
PoE+ Installationsanleitung
Inhalt des Produktpakets
Artikel Modelle / Varianten / Notizen
Ethernet Over Coax Adaptor PoE+
Optionales Zubehör
Gedruckte Dokumentation
Hardwareübersicht
AXIS T8640:
• AXIS T8641 Ethernet Over Coax Basiseinheit PoE+
• AXIS T8642 Ethernet Over Coax Geräteeinheit PoE+
AXIS T8003 PS57 (Netzteil) DIN-Schienenklemme Wandhalterung Rackmontagehalterung
AXIS T8640 Installationsanleitung (dieses Dokument)
DEUTSCH
Seite 26 AXIS T8640
Ethernet
Switch
Switch
Netzteil (optional)
Basiseinheit
Geräteeinheit
Geräteeinheit
Geräteeinheit
Geräteeinheit
Basiseinheit
Basiseinheit
Basiseinheit
PoE
Switch
Midspan
Basiseinheit
Geräteeinheit
Netzteil
Netzteil
Ethernet
Hardwareübersicht – Konfigurationsbeispiele
Beispiel 4: PoE-Geräte aus höheren Klassen als 4 benötigen zusätzlichen Midspan.
Beispiel 2: Externes Netzteil benötigt, wenn verwendet mit nicht-PoE-Switch.
Beispiel 3: PoE-betriebene Lösung (optionales Netzteil benötigt, wenn mit minderwertigen Kabeln verwendet)
PoE
Beispiel 1: Externes Netzteil benötigt, wenn verwendet mit nicht-PoE-Switch.
Switch
AXIS T8640 Seite 27
LED-Anzeigen
LED Verhalten/Farbe Bedeutung
Koax­Verbind­ung
Ethernet Verbin­dung
PoE over Coax
Für Kamera max. ver­fügbare PoE­Leistung (Watt)
Aus Kein Strom
Ein Verbindung hergestellt
Blinken Keine Einheiten an Koax erkannt
Orange/rot Datenrate < 100 %. Die Koax-Verbindung hat
Aus Keine Netzwerkverbindung vorhanden
Ein Ethernet-Verbindung hergestellt
Blinken Netzwerkaktivität am Port
Rot 10BASE-T-Verbindung. Einheiten müssen an ein
Aus Einheiten nicht erkannt
Ein PoE over Coax aktiviert
Rot (blinkt einmal auf)
Rot (blinkt zweimal auf)
Rot (blinkt dreimal auf)
Ein Max. PoE-Leistung, die aus 5 bis 25 Watt
Blinken PoE liefert weniger als 5 Watt.
ihre Leistungs- und Reichweitengrenze erreicht. Verringern Sie die Kabelentfernung oder schließen Sie ein AXIS T8003 PS57-Netzteil an die Geräteeinheit an.
mit 100BASE-T (Vollduplex) kompatibles Gerät angeschlossen sein, um einen wirksamen Betrieb zu gewährleisten.
Spannung niedrig. Überprüfen Sie die Art/ Polarität des Netzteils.
Kurzschluss. Überprüfen Sie auf Kabelprobleme und entfernen Sie alte Videogeräte.
Wegen Überlastung von Stromversorgung getrennt.
zuverlässig geliefert werden kann.
DEUTSCH
Seite 28 AXIS T8640
LED Verhalten/Farbe Bedeutung
Orange (Blinken) Leistungsgrenze fast erreicht
Rot (Blinken) Leistungsgrenze erreicht. Siehe Hinweis weiter
Hinweis:
• Verfügbare Leistung hängt von Kabellänge, Art und genutzter Stromquelle ab und wird automatisch bei der Verbindungsaufnahme berechnet. Um zum Beispiel die Stromversorgung an eine PoE-IP-Kamera mit einer Anforderung von max. 12 Watt zu gewährleisten, sollten Sie sicherstellen, dass die 15-Watt-LED leuchtet.
• Bei der Installation einer PTZ-Kamera oder anderer Geräte, deren Stromverbrauch sich ändern kann, sollten Sie diese LEDs überprüfen, während das Gerät maximal Strom verbraucht (also z. B. während sich die PTZ-Kamera bewegt).
• Schließen Sie ein AXIS T8003 PS57-Netzteil an die Basiseinheit an, um für maximale PoE-over-Coax-Leistung zu sorgen. Wenn mehr Strom benötigt wird als mit dem Kabel möglich ist, kann das Netzteil auch an die Geräteeinheit angeschlossen werden.
unten.
AXIS T8640 Seite 29
Technische Daten
Artikel
Modell AXIS T8640:
Datenrate Koaxialkabel: 100Mbit/s Vollduplex
Anschlüsse Koaxial: BNC 75 Ohm
Netzwerkkabel • Koaxial: Beliebiges 75-Ohm-Koaxialkabel (andere
Ausgangs­leistung
Eingangs­leistung
Installation/ Verwaltung
Konformität IEEE 802.3at, IEEE 802.3af, RoHS, WEEE, CE
Montage Wand, Rack, DIN-Schiene
Umgebung Innenbereich
Technische Daten
• AXIS T8641 Ethernet Over Coax Basiseinheit PoE+
• AXIS T8642 Ethernet Over Coax Geräteeinheit PoE+
Ethernet-Kabel: 100Base-TX Vollduplex
Ethernet: Abgeschirmtes RJ-45, EIA 568A und 568B
Impedanzen (Scheinwiderstände) werden auch unterstützt), bis 500 m bei voller Rate
• Ethernet: Abgeschirmtes Kabel der Kategorie 5 (oder höher), (Patch oder Crossover, automatische Erkennung)
AXIS T8641: PoE over Coax mit sicherer autom. Erkennung und Abschaltung AXIS T8642: PoE (IEEE 802.3af/at) aktiviert für erkannte Geräte bis 25,5 W
• AXIS T8641: PoE (IEEE 802.3at Klasse 4-versorgtes Gerät) oder Gleichstromnetzteil
• AXIS T8642: PoE over Coax oder Gleichstromnetzteil
• Gleichstromnetzteil: AXIS T8003 PS57 oder 44 – 56 V DC Klasse 2 isoliert (max. 0,7 Ampere)
• Geräteleistung: 1,5 W
Plug-and-Play-Installation, automatische Erkennung von PoE­und High PoE-fähigen Geräten und In-Line-Stromversorgung Lokale LED-Anzeige für Geräteverwaltung
DEUTSCH
Seite 30 AXIS T8640
Artikel
Zulassungen FCC Teil 15, Klasse B mit FTP-Kabel
Betriebs­bedingungen
Lagerung –40 °C bis 74 °C
Abmessungen (HxBxT)
Gewicht 140 g
Optionales Zubehör
Technische Daten
EN 55022 Klasse B (Strahlung, PoE-Betrieb) EN 55022 Klasse A (Strahlung, Gleichstrombetrieb) EN 55024 (Störfestigkeit)
–10 °C bis 50 °C Relative Luftfeuchtigkeit max. 95 % (nicht kondensierend)
104 x 54 x 24 mm
AXIS T8003 PS57-Netzteil, DIN-Schienenklemme, Wandmontagehalterung, Rackmontagehalterung
AXIS T8640 Seite 31
Beispiele für Stromquelle für:
PoE-Netzwerkkameras mit niedrigem Energieverbrauch (PoE IEEE
802.3af Klasse 1 oder 2, < 6 W)
• AXIS M11-Serie Netzwerk-Kamera-Serie
• AXIS 221 Netzwerk-Kamera
• AXIS M30 Netzwerk-Kamera-Serie
• Netzwerk-Kameras der AXIS M32 Serie
• AXIS M31-R/VE Netzwerk-Kamera-Serie
• AXIS P33 Netzwerk-Kameras (Modelle für Innenbereich)
• AXIS 212 PTZ/-V Netzwerk-Kamera
Verwendung eines 802.3af PoE­Switches
150 m CCS RG-59 350 m CC RG-59 400 m CC RG-6 500 m CC RG-11
Hinweis:
Analogkameras) CCS = 22 AWG kupferbeschichteter Stahl (schlechteste Leistung, wenn Kabelart nicht bekannt)
CC = Kupferkern-Kabel (häufigste Art bei richtig installierten
Verwendung eines AXIS T8003 PS57
280 m CCS RG-59 350 m CC RG-59 400 m CC RG-6 500 m CC RG-11
DEUTSCH
Seite 32 AXIS T8640
Beispiele für Stromquelle für:
PoE-Netzwerkkameras mit mittlerem Energieverbrauch (PoE IEEE
802.3af Klasse 1, 2 oder 3, < 10 W)
• AXIS M1054 Netzwerk-Kamera
• AXIS P13 Netzwerk-Kameras (Modelle zur Innenraumüberwachung)
• AXIS Q16 Netzwerk-Kameras (Modelle zur Innenbereich)
• AXIS Q1755 Netzwerk-Kamera
• Netzwerk-Kamera-Reihe AXIS Q19
• AXIS P33-VE Netzwerk-Kameras
Verwendung eines 802.3af PoE­Switches
CCS RG-59 nicht unterstützt 350 m CC RG-59 400 m CC RG-6 500 m CC RG-11
Verwendung eines AXIS T8003 PS57
200 m CCS RG-59 350 m CC RG-59 400 m CC RG-6 500 m CC RG-11
Beispiele für Stromquelle für:
PoE- oder PoE+-Netzwerkkameras mit vollem Energieverbrauch (PoE IEEE 802.3af Klasse 3, > 10 W) oder IEEE 802.3at.
• AXIS P13-E Netzwerk-Kameras
• AXIS Q16-E-Netzwerk-Kameras
• AXIS Q1755-E Netzwerk-Kamera
• Netzwerk-Kameras der AXIS P55-Serie
• AXIS Q60 Netzwerk-Kameras (Modelle zur Innenbereich)
Verwendung eines 802.3af PoE­Switches
Nicht unterstützt 80 m CCS RG-59
Verwendung eines AXIS T8003 PS57
350 m CC RG-59 400 m CC RG-6 500 m CC RG-11
AXIS T8640 Seite 33
Beispiele für Stromquelle für:
Individuell angepasste High PoE-Netzwerkkameras mit AXIS T8124 High PoE 60 W Midspan 1-Port (wie z. B. AXIS Q60-E-Netzwerkkameras).
Verwendung eines 802.3af PoE­Switches
PoE für Kamera nicht unterstützt. Das AXIS T8642-Gerät lässt sich über das Koaxialkabel mit Strom versorgen, die Kamera muss jedoch lokal über ein AXIS T8124 60 W Midspan betrieben werden.
Verwendung eines AXIS T8003 PS57
Hinweis:
• Die tatsächliche Reichweite hängt von mehreren Faktoren, wie der Kabelqualität, der Kabeldicke, den Anschlüssen und dem Stromverbrauch der Kamera ab.
• Bei den Reichweitewerten wurde der Einsatz kurzer (< 5 m) Cat-5e-Kabel zwischen den Geräten angenommen.
• CC - Kupferkern-Kabel (häufigste Art bei richtig installierten Analogkameras) CCS - 22 AWG kupferbeschichteter Stahl (schlechteste Leistung, wenn Kabelart nicht bekannt)
Garantie
Die Garantiebedingungen für Axis Produkte sowie weitere Informationen zum Thema Garantie finden Sie unter www.axis.com/warranty
DEUTSCH
AXIS T8640 Pagina 35
Unità
Unità base
Connettore di rete
Connettore
Connettore BNC
LED
di alimentazione
LED
periferica
AXIS T8640 Adattatore Ethernet Over Coax
PoE+ Guida all'installazione
Contenuto della confezione
Elemento Modelli/varianti/note
Ethernet Over Coax Adaptor PoE+
Accessori opzionali
Documentazione cartacea
AXIS T8640:
• AXIS T8641 Unità base PoE+ Ethernet Over Coax
• AXIS T8642 Unità periferica PoE+ Ethernet Over Coax
AXIS T8003 PS57 (Alimentatore) Clip barra DIN Staffa per montaggio a parete Staffa per montaggio su rack
AXIS T8640 Guida all'installazione (questo documento)
Panoramica dell’hardware
ITALIANO
Pagina 36 AXIS T8640
Switch
PoE
Alimentatore (opzionale)
Unità base
Unità periferica
Unità periferica
Unità periferica
Unità periferica
Unità base
Unità base
Unità base
Switch
PoE
Midspan
Unità base
Unità periferica
Alimentatore
Alimentatore
SwitchEthernet
Panoramica dell'hardware - Esempi di configurazione
Esempio 4. Le unità PoE di classe superiore alla 4 necessitano di unulteriore midspan.
Esempio 2. Alimentatore esterno necessario quando usato insieme a switch non PoE.
Esempio 3: Soluzione per alimentazione PoE (è necessario un alimentatore opzionale per l'utilizzo con cavi di bassa qualità)
Switch
Esempio 1. Alimentatore esterno necessario quando usato insieme a a switch non PoE.
Ethernet
AXIS T8640 Pagina 37
Indicatori LED
LED Stato/Colore Indicazione
Collega­mento coassiale
Collega­mento Ethernet
PoE su cavo coassiale
Off Assenza di alimentazione
On Connessione stabilita
Flash Unità non rilevate sul cavo coassiale
Arancione/rosso Velocità dati < 100%. La connessione coassiale
Off Collegamento di rete non disponibile
On Collegamento Ethernet stabilito
Flash Attività di rete sulla porta
Rosso Connessione 10BASE-T. Per un funzionamento
Off Unità non rilevate
On PoE su cavo coassiale attivata
Rosso (lampeggia una volta)
Rosso (lampeggia due volte)
Rosso (lampeggia tre volte)
ha raggiunto il limite di potenza e autonomia. Ridurre la distanza tra i cavi o collegare un alimentatore AXIS T8003 PS57 all'unità periferica.
corretto le unità devono essere collegate ad apparecchiature compatibili con 100BASE-T (full duplex).
Tensione bassa. Verificare il tipo e la polarità dell'alimentatore.
Corto circuito. Verificare eventuali difetti dei cavi e rimuovere le apparecchiature video precedenti.
Scollegamento dell'alimentazione dovuto a un sovraccarico.
ITALIANO
Pagina 38 AXIS T8640
LED Stato/Colore Indicazione
Alimenta zione PoE massima disponi­bile per la tele­camera (watt)
Nota:
• L'alimentazione disponibile è calcolata automaticamente al momento del
• In caso di installazione di una telecamera PTZ o di qualsiasi apparecchiatura i
• Per il raggiungimento della potenza massima PoE su cavo coassiale, collegare un
On Alimentazione PoE massima che può essere
Flash Meno di 5 watt di PoE disponibili.
Arancione (lampeggia)
Rosso (lampeggia) Limite di alimentazione raggiunto. Fare
collegamento e dipende dalla lunghezza e dal tipo di cavo e dalla fonte di alimentazione utilizzata. Per esempio, per garantire un'alimentazione affidabile a una telecamera IP PoE la cui alimentazione massima è 12 watt, verificare che il LED da 15 watt sia acceso.
cui requisiti di alimentazione possano cambiare, verificare i LED nel momento in cui l'apparecchiatura utilizza il livello massimo di energia, ad esempio quando la telecamera PTZ si sta muovendo.
alimentatore AXIS T8003 PS57 all'unità di base. Nel caso in cui sia necessaria più potenza di quanta possa sostenere il cavo, l'alimentatore può essere collegato all'unità periferica.
proporzionata in modo affidabile da 5 a 25 watt.
Limite di alimentazione quasi raggiunto
riferimento alla nota seguente.
AXIS T8640 Pagina 39
Specifiche tecniche
Elemento
Modello AXIS T8640:
Velocità di trasmissione dati
Connettori Cavo coassiale: Connettore BNC da 75 Ohm
Cavi di rete • Cavo coassiale: Qualsiasi cavo coassiale da 75 Ohm (altre
Potenza di uscita
Potenza di ingresso
Installazione e gestione
Conformità IEEE 802.3at, IEEE 802.3af, RoHS, WEEE, CE
Montaggio Su parete, rack e barra DIN.
Ambiente Per interni
Specifiche
• AXIS T8641 Unità base PoE+ Ethernet Over Coax
• AXIS T8642 Unità periferica PoE+ Ethernet Over Coax
Cavo coassiale: 100Mbps Full Duplex cavo Ethernet: 100Base-TX Full Duplex
Ethernet: RJ-45 schermato, EIA 568A e 568B.
impedenze supportate), fino a 500 m. alla massima velocità.
• Ethernet: Cavo schermato di categoria 5 o superiore; (cavi patch e incrociati rilevati automaticamente)
AXIS T8641: PoE su cavo coassiale con sicurezza di rilevazione automatica e auto spegnimento. AXIS T8642: PoE (IEEE 802.3af/at) attivata per le unità rilevate fino a 25.5W.
• AXIS T8641: PoE (IEEE 802.3at periferica di Classe 4) o alimentatore CC.
• AXIS T8642: PoE su cavo coassiale o alimentatore CC
• Alimentatore CC: AXIS T8003 PS57 o alimentazione isolata (massimo 0,7A) CC 44-56V di Classe 2.
• Potenza dell'unità: 1.5 W
Installazione plug-and-play; rilevazione automatica delle periferiche dotate di PoE e High PoE e somministrazione dell'alimentazione in linea. Schermo per la gestione locale dei LED
ITALIANO
Pagina 40 AXIS T8640
Elemento
Certificazioni FCC parte 15, Classe B con cablaggio FTP
Condizioni operative
Stoccaggio Da -40 °C a 74 °C
Dimensione (HxLxP)
Peso 140 g
Accessori facoltativi
Specifiche
EN 55022 Classe B (Emissioni, con alimentazione PoE) EN 55022 Classe A (Emissioni, con alimentazione CC) EN 55024 (Immunità)
Da -10 °C a 50 °C Umidità relativa: massimo 95% (senza condensa)
104 x 54 x 24 mm
Alimentatore AXIS T8003 PS57, clip barra DIN, staffa di montaggio a parete, staffa per montaggio su rack
AXIS T8640 Pagina 41
Esempi di alimentazione per:
Telecamere di rete a bassa tensione PoE (PoE IEEE 802.3af Classe 1 o 2; < 6 watt)
• Telecamere di rete serie AXIS M11
• Telecamere di rete AXIS 221
• Telecamere di rete serie AXIS M30
• Telecamere di rete serie AXIS M32
• Telecamere di rete serie AXIS M31-R/VE
• Telecamere di rete AXIS P33 (modelli per interni)
• Telecamere di rete AXIS 212 PTZ/-V
Utilizzo di uno switch PoE 802.3af Uso AXIS T8003 PS57
150m di CCS RG-59 350m di CC RG-59 400m di CC RG-6 500m di CC RG-11
Nota:
CC = Copper-Cored Cable (cavo con nucleo in rame), comune per i video analogici installati correttamente. CCS = 22AWG Copper-Coated Steel (cavo con nucleo in rame e acciaio a 22AWG), con rendimento peggiore se il tipo di cavo non è conosciuto.
280m di CCS RG-59 350m di CC RG-59 400m di CC RG-6 500m di CC RG-11
ITALIANO
Pagina 42 AXIS T8640
Esempi di alimentazione per:
Telecamere di rete a media tensione PoE (PoE IEEE 802.3af Classe 1, 2 o 3; < 10 watt)
• AXIS M1054 Videocamera di rete
• Telecamere di rete AXIS P13 Network Camera (modelli per interni)
• Telecamere di rete AXIS Q16 (modelli per interni)
• AXIS Q1755 Videocamera di rete
• Telecamere di rete serie AXIS Q19
• Telecamere di rete AXIS P33-VE
Utilizzo di uno switch PoE 802.3af Uso AXIS T8003 PS57
CCS RG-59 non supportato 350m di CC RG-59 400m di CC RG-6 500m di CC RG-11
Esempi di fonti di alimentazione per:
Telecamere di rete a piena potenza PoE o PoE+ (PoE IEEE 802.3af Classe 3; >10 watt) o IEEE 802.3at.
• Telecamere di rete AXIS P13-E
• Telecamere di rete AXIS Q16-E
• AXIS Q1755-E Videocamera di rete
• Telecamere di rete serie AXIS P55
• Telecamere di rete AXIS Q60 (modelli per interni)
200m di CCS RG-59 350m di CC RG-59 400m di CC RG-6 500m di CC RG-11
Utilizzo di uno switch PoE 802.3af Uso AXIS T8003 PS57
Non supportato 80m di CCS RG-59
350m di CC RG-59 400m di CC RG-6 500m di CC RG-11
AXIS T8640 Pagina 43
Esempi di fonti di alimentazione per:
Telecamere di rete con High PoE personalizzate che utilizzano un midspan AXIS T8124 High PoE 60 W a una porta, come le telecamere di rete serie AXIS Q60-E.
Utilizzo di uno switch PoE 802.3af Uso AXIS T8003 PS57
PoE verso la telecamera non supportato direttamente. L'unità AXIS T8642 può essere alimentata tramite cavo coassiale, ma è necessario utilizzare un midspan AXIS T8124 a 60W per alimentare la telecamera localmente.
Nota:
• L'autonomia effettiva dipende da diversi fattori tra i quali la qualità e lo
spessore del cavo, i connettori utilizzati e il consumo energetico della telecamera.
• I dati relativi all'autonomia suppongono l'utilizzo di cavi Cat-5e corti (<5m) tra
le apparecchiature.
• CC = Copper-Cored Cable (cavo con nucleo in rame), comunemente usato per
installazioni analogiche a norma. CCS = 22AWG Copper-Coated Steel (cavo con nucleo in rame e acciaio a 22AWG), potrebbe comportare un rendimento peggiore.
Garanzia
Per informazioni relative alla garanzia del prodotto AXIS ed ogni altra ulteriore informazione correlata, di consultare la pagina www.axis.com/warranty
ITALIANO
AXIS T8640 Página 45
Guía de instalación del Adaptador de
Ethernet a través de cable coaxial PoE+ AXIS
T8640
Contenido del paquete
Artículo Modelos/variantes/notas
Adaptador de Ethernet a través de cable coaxial PoE+
Accesorios opcionales
Material impreso Guía de instalación de AXIS T8640 (este documento)
AXIS T8640:
• Unidad base Ethernet a través de cable coaxial PoE+ AXIS T8641
• Unidad de dispositivo Ethernet a través de cable coaxial PoE+ AXIS T8642
AXIS T8003 PS57 (fuente de alimentación) Clip para carril DIN Soporte de pared Escuadra para montaje en bastidor
ESPAÑOL
Página 46 AXIS T8640
Unidad de
Unidad base
Conector de red
Conector de
Conector BNC
LED
alimentación
LED
dispositivo
Presentación del hardware
AXIS T8640 Página 47
Con-
Ethernet
PoE
Fuente de alimentación (opcional)
Unidad base
Unidad de dispositivo
Unidad de dispositivo
Unidad de dispositivo
Unidad de dispositivo
Unidad base
Unidad base
Unidad base
Conmutador
PoE
Midspan
Unidad base
Unidad de dispositivo
Fuente de alimentación
Fuente de alimentación
Conmutador
Presentación del hardware: ejemplos de configuración
Ejemplo 4. Los dispositivos PoE con una clasificación superior a 4 requieren un midspan adicional.
Ejemplo 2. Se necesita una fuente de alimentación externa cuando se utiliza con un conmutador que no sea PoE.
Ejemplo 3. Solución alimentada mediante PoE (se necesita una fuente de alimentación opcional cuando se utiliza con cables de baja calidad)
Conmutador
Ejemplo 1. Se necesita una fuente de alimentación externa cuando se utiliza con un conmutador que no sea PoE.
Ethernet
mutdor
ESPAÑOL
Página 48 AXIS T8640
Indicadores LED
LED Comportamiento/
Enlace coaxial
Enlace Ethernet
PoE a través de cable coaxial
color
Desactivado Sin alimentación
Activado Conexión establecida
Parpadeo Unidades no detectadas en la conexión coaxial
Naranja/rojo Velocidad de datos < 100%. La conexión coaxial
Desactivado Sin conexión a la red
Activado Enlace Ethernet establecido
Parpadeo Actividad de red en el puerto
Rojo Conexión 10BASE-T. Para funcionar
Desactivado Unidades no detectadas
Activado PoE a través de cable coaxial activado
Rojo (1 parpadeo) Baja tensión. Compruebe el tipo o la polaridad
Rojo (2 parpadeos) Cortocircuito. Compruebe si existen fallos en el
Rojo (3 parpadeos) Alimentación desconectada debido a sobrecarga.
Indicación
ha alcanzado el límite de alimentación y rango. Reduzca la distancia del cable o conecte una fuente AXIS T8003 PS57 a la unidad del dispositivo.
eficazmente, las unidades se deben conectar a un equipo 100BASE-T (dúplex completo) compatible.
de la fuente de alimentación.
cable y retire el equipo de vídeo antiguo.
AXIS T8640 Página 49
LED Comportamiento/
Máxima alimenta ción PoE disponib le para la cámara (vatios)
color
Activado Máxima alimentación PoE que se puede
Parpadeo Menos de 5 vatios de PoE disponibles.
Naranja (parpadeando)
Rojo (parpadeando)
Indicación
suministrar de forma fiable, de 5 a 25 vatios.
Próximo al límite de potencia
Límite de potencia alcanzado. Consulte la nota a continuación.
Nota:
• La alimentación disponible es específica para la longitud del cable, el tipo y la fuente de alimentación empleados, y se calcula automáticamente durante la conexión. Por ejemplo, para garantizar un suministro fiable de alimentación a una cámara IP PoE cuyo requisito de alimentación máxima es de 12 vatios, compruebe que está encendido el LED de 15 vatios.
• Si se instala una cámara PTZ o cualquier equipo cuyo requisito de alimentación puede variar, compruebe los LED siguientes mientras que el equipo alcanza la máxima potencia, como cuando la cámara PTZ se está moviendo.
• Para conseguir la máxima alimentación PoE a través de cable coaxial, conecte una fuente de alimentación AXIS T8003 PS57 a la unidad base. Si se necesita más potencia de la que el cable puede soportar, se puede conectar la fuente de alimentación a la unidad del dispositivo.
ESPAÑOL
Página 50 AXIS T8640
Especificaciones técnicas
Artículo
Modelo AXIS T8640:
Velocidad de datos
Conectores Coaxial: BNC 75 ohmios
Cables de red • Coaxial: cualquier cable coaxial de 75 ohmios (se admiten
Potencia de salida
Potencia de entrada
Instalación/ gestión
Cumplimiento normativo
Especificaciones
• Unidad base Ethernet a través de cable coaxial PoE+ AXIS T8641
• Unidad de dispositivo Ethernet a través de cable coaxial PoE+ AXIS T8642
Cable coaxial: 100 Mbps Dúplex completo Cable Ethernet: 100Base-TX Dúplex completo
Ethernet: RJ-45 blindados, EIA 568A y 568B
otras impedancias), a 500 m a velocidad completa
• Ethernet: blindado de categoría 5 (o superior); (interconexión o cruzado, detección automática)
AXIS T8641: PoE a través de cable coaxial con detección automática y desconexión automática seguras AXIS T8642: PoE (IEEE 802.3af/at) activado para dispositivos detectados de hasta 25,5 vatios
• AXIS T8641: PoE (dispositivo alimentado IEEE 802.3at Clase 4) o fuente de alimentación CC
• AXIS T8642: PoE a través de cable coaxial o fuente de alimentación CC
• Fuente de alimentación CC: AXIS T8003 PS57 o suministro aislado de 44 a 56 V CC Clase 2 (máx., 0,7 amperios)
• Alimentación del dispositivo: 1,5 vatios
Instalación plug-and-play; detecta automáticamente los dispositivos compatibles con PoE y High PoE y suministra alimentación en línea Pantalla local de gestión de LED
IEEE 802.3at, IEEE 802.3af, RoHS, WEEE, CE
AXIS T8640 Página 51
Artículo
Montaje En pared, bastidor o carril DIN
Entorno Para interiores
Homologaciones FCC sección 15, Clase B con cableado FTP
Condiciones de funcionamiento
Almacenamiento De -40 °C a 74 °C
Dimensiones (Alt. x Anch. x Prof.)
Peso 140 g
Accesorios opcionales
Especificaciones
EN 55022 Clase B (emisiones, alimentado mediante PoE) EN 55022 Clase A (emisiones, alimentado mediante CC) EN 55024 (inmunidad)
De -10 °C a 50 °C Humedad relativa: 95% como máximo (sin condensación)
104 x 54 x 24 mm
Fuente de alimentación AXIS T8003 PS57, clip para carril DIN, escuadra para montaje en pared, escuadra para montaje en bastidor
ESPAÑOL
Página 52 AXIS T8640
Ejemplos de fuente de alimentación para:
Cámaras de red PoE de baja potencia (PoE IEEE 802.3af Clase 1 o 2; < 6 vatios)
• Serie de cámaras de red AXIS M11
• Cámara de red AXIS 221
• Serie de cámaras de red AXIS M30
• Serie de cámaras de red AXIS M32
• Serie de cámaras de red AXIS M31-R/VE
• Cámaras de red AXIS P33 (modelos para interiores)
• Cámara de red AXIS 212 PTZ/-V
Utilización de un conmutador PoE
802.3af
150 m de CCS RG-59 350 m de CC RG-59 400 m de CC RG-6 500 m de CC RG-11
Nota:
CC = cable recubierto de cobre (el más habitual para vídeo analógico instalado correctamente) CCS = acero recubierto de cobre de 22 AWG (muestra el peor rendimiento si se desconoce el tipo de cable)
Utilización de AXIS T8003 PS57
280 m de CCS RG-59 350 m de CC RG-59 400 m de CC RG-6 500 m de CC RG-11
AXIS T8640 Página 53
Ejemplos de fuente de alimentación para:
Cámaras de red PoE de media potencia (PoE IEEE 802.3af Clase 1, 2 o 3; < 10 vatios)
• Cámara de red AXIS M1054
• Cámaras de red AXIS P13 (modelos para interiores)
• Cámaras de red AXIS Q16 (modelos para interiores)
• Cámara de red AXIS Q1755
• Serie de cámaras de red AXIS Q19
• Cámaras de red AXIS P33-VE
Utilización de un conmutador PoE
802.3af
No admite CCS RG-59 350 m de CC RG-59 400 m de CC RG-6 500 m de CC RG-11
Utilización de AXIS T8003 PS57
200 m de CCS RG-59 350 m de CC RG-59 400 m de CC RG-6 500 m de CC RG-11
Ejemplos de fuente de alimentación para:
Cámaras de red PoE o PoE+ de potencia completa (PoE IEEE 802.3af Clase 3; >10 vatios) o IEEE 802.3at.
• Cámaras de red AXIS P13-E
• Cámaras de red AXIS Q16-E
• Cámara de red AXIS Q1755-E
• Serie de cámaras de red AXIS P55
• Cámaras de red AXIS Q60 (modelos para interiores)
Utilización de un conmutador PoE
802.3af
No admitido 80 m de CCS RG-59
Utilización de AXIS T8003 PS57
350 m de CC RG-59 400 m de CC RG-6 500 m de CC RG-11
ESPAÑOL
Página 54 AXIS T8640
Ejemplos de fuente de alimentación para:
Cámaras de red High PoE personalizadas que utilizan el Midspan AXIS T8124 High PoE de 1 puerto de 60 vatios, como las cámaras de red AXIS Q60-E.
Utilización de un conmutador PoE
802.3af
No se admite la alimentación PoE a la cámara. El dispositivo AXIS T8642 se puede alimentar a través del cable coaxial, pero debe utilizarse un Midspan AXIS T8124 de 60 vatios para alimentar localmente la cámara.
Utilización de AXIS T8003 PS57
Nota:
• El rango real depende de varios factores, como la calidad del cable, el grosor del
cable, los conectores y el consumo de energía de la cámara.
• En las cifras del rango se suponen cables Cat-5e cortos (<5 m) entre los
equipos.
• CC: cable recubierto de cobre (el más habitual para vídeo analógico instalado
correctamente) CCS: acero recubierto de cobre de 22 AWG (muestra el peor rendimiento si se desconoce el tipo de cable)
Garantía
Para información sobre la garantía de productos Axis e información relacionada, consulte www.axis.com/warranty
Installation Guide Ver.1.2 AXIS T8640 Ethernet Over Coax Adaptor
PoE+ © Axis Communications AB, 2012 Part No. 49300
Printed: October 2012
Loading...