Avycon AIVO-70AET User Manual

All-in-one Network Tester

User’s Manual

（AIVO-70AET）

Thank you for purchasing the IP camera tester. Please read the manual before using the IP camera

tester and use properly.

For using the IP camera tester safely, please first read the「Safety Information」carefully in the

manual.

The manual should be kept well in case of reference. Keep the S/N label for after-sale service within warranty period. Product without S/N label will

be charged for repair service.

If there is any question or problem while using the IP camera tester, or damages occurred on the

product, please contact our technical Department.

Content

1 .Safety information ----------------------------------------------------------------------------------------------------- 1

2. IP Camera Tester Introduction --------------------------------------------------------------------------------------- 2

2.1 General ----------------------------------------------------------------------------------------------------------- 2

2.2 Features----------------------------------------------------------------------------------------------------------- 2

2.3 Function ---------------------------------------------------------------------------------------------------------- 5

2.4 Packing list ---------------------------------------------------------------------------------------------------- 12

2.5 Function interface -------------------------------------------------------------------------------------------- 13

3. Operation -------------------------------------------------------------------------------------------------------------- 16

3.1 Installing the Battery ----------------------------------------------------------------------------------------- 16

3.2 Instrument connection --------------------------------------------------------------------------------------- 17

3.2.1 IP camera connection -------------------------------------------------------------------------------------- 17

3.2.2 Analog camera connection ------------------------------------------------------------------------------- 19

3.2.3 HD Coaxial camera connection ------------------------------------------------------------------------- 19

3.3 OSD menu ----------------------------------------------------------------------------------------------------- 20

3.3.1 IP discovery ------------------------------------------------------------------------------------------- 22

3.3.2 Video monitor test ----------------------------------------------------------------------------------- 22

3.3.3 Color-bar generator (TV OUT) -------------------------------------------------------------------- 32

3.3.4 ONVIF ------------------------------------------------------------------------------------------------- 33

3.3.5 IP camera test ----------------------------------------------------------------------------------------- 43

3.3.6 SDI camera tes --------------------------------------------------------------------------------------- 46

3.3.7 CVI camera test -------------------------------------------------------------------------------------- 48

3.3.8 TVI camera test -------------------------------------------------------------------------------------- 53

3.3.9 AHD camera test ------------------------------------------------------------------------------------- 54

3.3.10 IP address scan -------------------------------------------------------------------------------------- 55

3.3.11 PING Test-------------------------------------------------------------------------------------------- 56

3.3.12Cable Test -------------------------------------------------------------------------------------------- 57

3.3.13 Cable Search ---------------------------------------------------------------------------------------- 57

3.3.14 Port Flashing ---------------------------------------------------------------------------------------- 59

3.3.15Data monitor ----------------------------------------------------------------------------------------- 60

3.3.16 Optical power meter ------------------------------------------------------------------------------- 60

3.3.17 Visual Fault Locator ------------------------------------------------------------------------------- 62

3.3.18 Digital Multi-meter -------------------------------------------------------------------------------- 64

3.3.19 Media Player ---------------------------------------------------------------------------------------- 71

3.3.20 Audio player ----------------------------------------------------------------------------------------- 72

3.3.21 LED Flashlight -------------------------------------------------------------------------------------- 73

3.3.22 PoE Voltage test ------------------------------------------------------------------------------------ 73

3.3.23 TDR cable test -------------------------------------------------------------------------------------- 74

3.3.24Calculator --------------------------------------------------------------------------------------------- 77

3.3.25 Browser ---------------------------------------------------------------------------------------------- 77

3.3.26 IP camera viewer ----------------------------------------------------------------------------------- 78

3.3.27 PoE power / DC12V 2A and DC 5V 2A USB power output ------------------------------- 79

3.3.28 Application tools ----------------------------------------------------------------------------------- 80

3.3.29 APPS Folder ----------------------------------------------------------------------------------------- 89

3.3.30 System Setting -------------------------------------------------------------------------------------- 93

3.3.31 Update ------------------------------------------------------------------------------------------------ 95

3.4 Audio test ------------------------------------------------------------------------------------------------------ 96

3.5 HDMI output -------------------------------------------------------------------------------------------------- 96

3.6 PoE power output --------------------------------------------------------------------------------------------- 97

3.7 DC12V 2A power output ----------------------------------------------------------------------------------- 98

4. Specifications --------------------------------------------------------------------------------------------------------- 99

4.1 General Specifications --------------------------------------------------------------------------------------- 99

4.2 Multi-meter specifications --------------------------------------------------------------------------------- 102

4.3 Optical power meter specifications ---------------------------------------------------------------------- 104

4.4 Visual fault locator specifications ------------------------------------------------------------------------ 104

1 .Safety information

◆ The tester is intended to use in compliance with the local rules of the electrical usage and avoid to apply at the places which are inapplicable for the use of electrics such as hospital, gas station etc.

◆ To prevent the functional decline or failure, the product should not be sprinkled or damped.

◆ The exposed part of the tester should not be touched by the dust and liquid.

◆ During transportation and use, it is highly recommended to avoid the violent collision and vibration

of the tester, lest damaging components and causing failure.

◆Don’t leave the tester alone while charging and recharging. If the battery is found severely hot, the

tester should be powered off from the electric source at once. The tester should not be charged over 8 hours.

◆ Don’t use the tester where the humidity is high. Once the tester is damp, power off immediately and move away other connected cables.

◆ The tester should not be used in the environment with the flammable gas.

◆ Do not disassemble the instrument since no component inside can be repaired by the user. If the

disassembly is necessary indeed, please contact with the technician of our company.

◆ The instrument should not be used under the environment with strong electromagnetic interference.

◆ Don’t touch the tester with wet hands or waterish things.

◆ Don’t use the detergent to clean and the dry cloth is suggested to use. If the dirt is not easy to remove,

the soft cloth with water or neutral detergent can be used. But the cloth should be tweaked sufficiently.

About Digital Multi-meter

◆ Before using, you must select the right input jack, function and range.

◆ Never exceed the protection limit values indicated in specifications for each range of measurement.

◆When the tester is linked to a measurement circuit, do not touch unused terminals.

◆Do not measure voltage if the voltage on the terminals exceeds 660V above earth ground.

◆At the manual range, when the value scale to be measured is unknown beforehand, set the range

selector at the highest position.

◆Always be careful when working with voltages above 60V DC or 40V AC, keep fingers behind the probe barriers while measuring.

Page.1.

◆Never connect the meter with any voltage source while the function switch is in the current, resistance, capacitance, diode, continuity, otherwise it will damage the meter.

◆Never perform capacitance measurements unless the capacitor to be measured has been discharged fully.

◆Never measure any of resistance, capacitance, diode or continuity measurements on live circuits.

Visual laser sources

When you turn on visual laser sources, please don’t stare at it, or will damage to eyes When not using it, please turn it off and cover the protective cap .

2. IP Camera Tester Introduction

2.1 General

The 7 inch touch screen IP camera monitor and tester is designed for maintenance and installation of IP cameras and analog cameras as well as other security equipment. The 1280x800 resolution enables it to display network HD cameras and analog cameras in high resolution. The unit supports many ONVIF PTZ and analog PTZ control. The combination of touch screen and key buttons make the IP camera tester very user- friendly. The tester is also a great tool for Ethernet network testing. It can test PoE power voltage, PING, and IP address searching. You can use the blue cable tracer to locate individual connected cables from a bundle of cables. Test LAN cable for proper connection termination. Other functions include providing 24W PoE power to your camera, LED Flashlight, DC 12V 2A power output and much more. Its portability, user-friendly design and many other functions make the IP tester an essential tool for all installers or technicians.

2.2 Features

 7 inch 1280×800 touch screen, easy to operate  IP discovery, do not need to know the first two digits of camera’s IP address , it can auto-scan

the whole network segment IP, and auto-modify tester’s IP address

 Rapid ONVIF, search camera quickly, auto log in and display image from the camera, activate

Page.2.

Hikvision camera.

 Hik test tool app is design for activating and debugging Hikvision camera, can auto-identify

unactivated hikvision camera, also can display image from the Hikvision camera.

 ONVIF IP camera video testing.

 Compatible with H.264/MPEG4/MJPEG IP cameras, such as Dahua, HIKVISION, and ACTI

Customized service is available.

 Built in Wi-Fi, can receive image from wireless camera, as well as ONVIF and customized IP

cameras.

 SDI Digital camera image display, record and screen snapshot *  HD CVI camera image display, zoom, video record and playback ,Coaxial PTZ control and call

camera OSD menu *

 HD TVI camera image display, zoom, video record and playback ,Coaxial PTZ control and call

camera OSD menu *

 AHD camera image display, zoom, video record and playback, Coaxial PTZ control and call

camera OSD menu *

 HDMI signal output, supports up to 1080P.  Analog camera image display, auto adapt and display the video format of NTSC/PAL

 Support more than 30 protocols, such as PELCO-P,PELCO-D,SAMSUNG etc  Video image digital zoom to view the image in greater detail.  Snapshot function allows you to save the current image as a JPG file in the SD card.  LED Flashlight.  4GB Micro SD card included.  LCD screen brightness/contrast/color Saturation adjustable  Visual fault locator, to test fiber’s bending and breakage *  Optical power meter, test fiber loss and value *  Digital Multi-meter , DC and AC voltage measurement, Resistance measurement Continuity test,

Diode measurements, Capacitance measurement *

Page.3.

 Enhanced Color bar generator, PAL/NTSC multi-system color bar video generator (Eight-system

switchable, transmit/receive eight-system colorful images).

 PEAK video signal level, SYNC signal level, Color burst chroma level measurement,test video

signal attenuation

 Cable tracer, by sending the audio signal, enables the blue cable tracer tester to find the

connected cable from messy cables.

 Ping test, PING is the most conventional network debugging tools; it is used for testing if the

connected IP camera or other network equipment’s Ethernet port is working normally and the IP

address is correct.

 In digital IP surveillance applications, if the IP camera’s IP address is not known; the device

cannot be used. An IP address scan can quickly search for the connected IP camera or other network device’s IP address.

 The PoE voltage test can test for PoE voltage when a POE switch is supplying POE power to an

IP camera

 TDR cable test, test cable open circuit and short-circuit *  Cable test , Test LAN cable or telephone cable,UTP cable etc ,cable type and the sequence of

wires will be displayed

 Support RS232/RS485,rate 600 ～ 115200bps adjustable  PTZ protocol analysis, control protocol command displays to check RS485 transmission

whether is normal, easy to find the fault device  PTZ control. Pan/tilts the P/T unit, zooms in/out the lens, adjusts the focus, aperture and

sets and the preset position

 DC5V 2A power output for USB charging (No USB data exchange, voltage only)  PoE power output, supply temporary power for PoE camera  DC5V 2A power output, as a power bank

 Audio input and output, test and output the audio signal  7.4V 48.1Wh Battery. Remaining battery charge indicator, Lithium Ion Polymer Battery can last

16 hours for normal use after charging for 8 hours

Page.4.

2.3 Function

2.3.1 Touch screen and OSD menu

The IP camera tester combines touch screen control and physical buttons. This combination makes the

tester very user friendly. The test meter allows you to move the function icons from the tester’s main

menu to the APPS folder or move them back to customize the main menu

2.3.2 IP discovery

IP discovery, do not need to know the first two digits of camera’s IP address , it can auto-scan the whole network segment IP, and auto-modify tester’s IP address

2.3.3 Rapid ONVIF

Rapid ONVIF, search camera quickly, auto log in and display image from the camera, activate Hikvision camera.

2.3.4 Hik test tool

Hik test tool app is design for activating and debugging Hikvision camera, can auto-identify unactivated hikvision camera, also can display image from the Hikvision camera.

2.3.5 IP camera test

The device is designed for ONVIF IP camera testing. It can display the image from an IP camera and change the IP address. The 7 inch 1280x800 screen display allows the user to view the image with a sufficient screen size.

With the ONVIF tool, you can display the image from an IP camera and use the PTZ functions.

Currently the IP camera tester supports more than 70 brands’ IP cameras, such as most, ACTi, Dahua,

Hikvision, Samsung, Honeywell and many more.

OEM service is available. Users can send us the IP camera for our engineers try to add the protocols to the tester, or send us the mobile apps (Android version. APK files) to install in the tester.

2.3.6 Analog camera test

Page.5.

Displays an analog camera image on the 7 inch 1280 x800 LCD screen display. Supports PAL & NTSC formats. The LCD screen's back light brightness, video image brightness, contrast and color saturation are all adjustable.

2.3.7 Video level meter

Perform NTSC and PAL video amplitude signal measurements for PEAK to PEAK , SYNC levels,

and COLOR BURST chroma level

Video signal PEAK to PEAK level:

For NTSC format, the video signal level is 140±15IRE

For PAL format, the video signal level is 1000±200mV

If the level is too low, it will cause the image to lose quality and limit the distance it will travel over

cable. If the level is too high, it will lead to wash out of the image

SYNC level: Testing the amplitude of the video sync pulse to verify if the video level is correct.

For NTSC format, the SYNC level is 40 ± 5IRE

For PAL format, the SYNC level is 300 ± 35mV

If the level is too low, it will cause the image to not frame out properly. If the level is too high, it will

lead to a poor quality

COLOR BURST level: Testing the color burst level will determine if the burst signal is sufficient to

trigger the displays color producing circuit. Burst will diminish in amplitude over longer cable runs and

can get fall below the threshold for the video display to show a color image.

For NTSC format, the Chroma standard level is 40 IRE

For PAL format, the Chroma standard level is 280mV

If the Chroma level is too low, the color will not be as deep, and some details of the image will get

Page.6.

washed out. If the Chroma level is too high, there will be spots on the image. If the coaxial cable is too long, it will reduce the chroma level

2.3.8 PTZ controller

Displays and allows for analysis of analog video and controls Pan/tilt/zoom function of PTZ analog cameras. For PTZ testing, setup the controlling parameters from the meter to match those of the camera: e.g. PTZ protocol (PELCO-D, etc.), communication port (RS-485, etc.), baud rate, PTZ camera ID and pan/tilt speed.

2.3.9 Enhanced Color bar generator

The tester sends out color bars via its BNC output to the monitor. This is used to test for a problem in the cable going from the camera back to the monitoring area

2.3.10 12VDC 2A power output port and 5VDC 2A USB power port

The unit can power a camera with its 12V DC 2A power output. Also included is a built in 5V DC 2A power output port used to charge USB devices. NOTE: This USB port is for charging only and has no ability to transfer data.

2.3.11 Audio testing

Test the audio from mic level input devices. Connect the tester and mic level device with the audio cable. Supports audio recording and output. to monitor and / or record audio.

2.3.12 Cable tester

Test LAN cable or telephone cable. Connect LAN cable or telephone cable with the CCTV tester and cable tester. And then the connecting status, cable type and the sequence of wires will be displayed, as well as display the serial number of the cable tester kit.

2.3.13 PTZ data analysis

Search the Control protocol code from Multifunction keyboard or DVR by RS485 /RS232 interface, test the PTZ control command data whether received anomaly and RS485/RS232 data transmission.

Screen displays 16 hexadecimal codes such as PELCO-P:A0 00（Add） xx xxxxxx AF xx

Page.7.

PELCO-D:FF 01（Add）xx xxxxxxxx

2.3.14 Digital Image zoom on the monitor

Set image zoom up to 4X to get a closer look at all the image detail. Supports analog and many IP cameras

2.3.15 Video screenshot, record and playback

Capture the video image displayed and save as a JPEG file. You can also record and save the current video to the SD card. The recorded files can play directly via Media player or under the function of

“Playback”.

2.3.16 DHCP dynamic address assignment

Built in DHCP server: Dynamically assign IP address for the IP camera or network device.

2.3.17 Access the dynamic IP address

The IP tester can directly access a dynamic IP address assigned from its DHCP server and use it as the tester’s IP address. No need to set a IP address manually.

2.3.18 Multiple network IP Cameras Test

Supports Multi- segmented Static IP address setting which can simultaneously test different segments of IP network Cameras.

2.3.19 IP address scan

The IP address scan can quickly search for connected IP cameras or another network device IP address.

2.3.20 PING Test

PING is the most conventional network debugging tool; it is used for testing if the connected IP camera or other network equipment is working normally and the IP address is correct.

2.3.21 Port Finder

The tester will send signals to make the connected PoE port flicker at a set frequency. This will enable the installer to easily and quickly find the connected port for an Ethernet cable.

2.3.22 PoE Test

Test the PoE voltage from a PoE switch. The unit will clearly display the voltage for each wire in an

Page.8.

Ethernet cable.

2.3.23 Digital Multi-meter

The tester has built in highly stable and reliable 33/4 digit (6600) digital multi-meter. It is used for the DC and AC voltage measurement, AC and DC current measurement, Resistance measurement, Continuity test, Diode measurements, Capacitance measurement, Auto/Manual measuring range switching, relative value measurement and locking. It is easy operation and professionally accurate.

2.3.24 Visual fault locator

Visual Fault Locator with 650nm wavelength can emit red laser sources to test multi-mode and single mode fiber’s bending and breakage, and Continuous light-emitting and 1HZ, 2Hz modulating light

output. It is indispensable tool in fiber project constructing, fiber net-work maintaining, optical

component manufacture and research.

2.3.25 Optical Power Meter

The IP camera tester adopts the most advanced handheld instrument specific integrated chip , achieve ultra-low power operation, with the 7 TFT-LCD High-definition screen display ,five wavelength calibration points 1625nm,1550nm ,1490nm , 1310nm , 1300nm , 850nm.Linear or nonlinear optical power display, it can measure the optical power value, and also be used for Relative measurement of optical fiber link loss. It is necessary tool for fibre-optic communication, cable television system and security system maintenance.

2.3.26 LED Flashlight

Press the LED On/Off button to use the LED flashlight.

2.3.27 TDR cable open circuit and short circuit measurement

TDR cable testing, accurately measure BNC cable, network cable, controls cable’s open circuit and

short-circuits location. It greatly improves working efficiency.

2.3.28 WIFI

With built in WIFI, you can view the video from a wireless camera (ONVIF or customized camera) or

connect to a Wireless network.

Page.9.

2.3.29 SDI camera test

SDI digital video surveillance testing, support 720p 60fps / 1080p 30fps / 1080i 60fps digital camera image test and video image zoom, record, snapshot, photo viewer and video playback .

2.3.30 CVI camera test

HD CVI video surveillance testing, support720p 25,30,50,60fps / 1080p 25,30fps, when CVI signal input, HD CVI camera image display, zoom, view photos, video record and playback, Coaxial PTZ control and call up the camera OSD menu.

2.3.31 TVI camera test

HD TVI video surveillance testing, support720p 25,30,50,60fps/ 1080p 25,30fps , when TVI signal input , HD TVI camera image display, zoom ,view photos ,video record and playback .Coaxial PTZ control and call up the camera OSD menu.

2.3.32 AHD camera test

AHD video surveillance testing, support 720p 25,30fps/ 1080p 25,30fps, when AHD signal input , AHD camera image display, zoom ,view photos ,video record and playback ,Coaxial PTZ control and call up the camera OSD menu.

2.3.33 PoE power supply

Supports PoE 802.3at power at 48V and up to 24W.

2.3.34 HDMI signal output

The HDMI output port supports up to a 1080p 60Hz resolution output.

2.3.35 Network bandwidth testing

The network bandwidth test needs two IP tester meters to test bandwidth: one as a transmitter, the other as a receiver.

2.3.36 Cable Tracer (cable search)

Cable identification by use of an audio signal. This function enables the blue cable tracer to find the connected cable from a bundle of cables with an audio tone.

Page.10.

2.3.37 Screen image rotates 180 degrees

You can manually rotate the display 180 degrees using the settings. .

2.3.38 FTP Server

Start the tester’s Wi-Fi or connect the tester’s LAN port to the network. Once the tester is online, start

its FTP Server and directly access files from the tester’s SD card. This also allows for the user to

upgrade the tester firmware.

Page.11.

2.4 Packing list

1). Tester

2). Adaptor DC12V 2A

3) Network cable tester

4) Polymer lithium ion battery (7.4V DC 6500mAh)

5). BNC cable

6). RS485 cable

7). SC,ST connector（Only for optical power meter）

8). Multi-meter test leads one pair of red and black (only for the Multi-meter models)

9). Output Power cable

10). Audio cable

11). TDR alligator clamp (only for TDR models)

12). Safety cord

13). Tool bag

14). Manual

15) 4GB SD card

Page.12.

2.5 Function interface

Page.13.

Press more than 2 seconds, turn on or off the device ,short press to turn on or off the menu display

2 Menu key

3 4xzoom the image displays.

4 Video record

5 Snapshot

6 Far focus: Focus the image faraway

7 Near focus: Focus the image nearby

8 TELE: zoom in the image

9 WIDE: zoom out the image

10 Open/set ,Confirm the setting of parameters, open or enlarge the aperture

Return/Close : Return or cancel while setting parameters of the menu, close or decrease the aperture

12 Confirm key

13 Upward, set function or add parameter. Tilt the PTZ upward

Downward, set function or reduce the value of the parameter. Tilt the PTZ downward

15 Leftward, select the parameter whose value will be changed

Rightward, select the parameter whose value will be changed. Add the value of the parameter. Pan the PTZ right

Page.14.

Top interface

Bottom interface

Multimeter interface

The charge indicator: it lights red while the battery is being charged. As the charging is

complete, the indicator turns off automatically

The RS485/RS232 data transmission indicator: it lights red while the data is being transmitted

The data received indicator: it lights red while the data is being received

The power indicator: it lights green while the tester is powered on by the adapter

Visible red laser source emits Interface

DC12V2A power output , for provisional DC power supply

SDI input (BNC interface)

"HD IN" , AHD /TVI/CVI Coaxial interface

Video signal input（BNC interface）

Video signal output（BNC interface）/ cable tracer interface

Page.15.

Optical power meter interface

LED lamp

RS485 Interface: RS485communication for the PTZ

RS232 Interface: RS232 communication for the PTZ

TDR cable test interface

HDMI output interface

Micro SD card moveable,(comes with 4GB, supports up to 32GB)

UTP cable port: UTP cable tester port/ Cable tracer port

Audio output and earphone interface

Audio input

PSE power sourcing equipment. Tests PoE voltage

PoE power supply output or LAN test port (Use to test PoE or non-PoE IP camera)

USB 5V 2A power output (used only for power, not data)

DC12V2A charging interface

DC12V2A power output , for provisional DC power supply

3. Operation

3.1 Installing the Battery

The tester has built-in lithium ion polymer rechargeable battery. The battery cable inside battery

cabin should be disconnected for safety during transportation! Prior to the use of the instrument, the battery cables inside the battery cabin should be well connected.

Usually it doesn’t need to disconnect the cable at the normal use

Pressing the key continuously can power on or off the tester.

Notice:Pls use the original adaptor and connected cable of the device!

Page.16.

When the battery icon is full or the charge indicator turns off automatically, indicate the battery

charging is completed

Notice: When the Charge Indicator turns off, the battery is approximately 90%

charged. The charging time can be extended for about 1 hour and the charging time within 12 hours will not damage the battery.

Notice :Press the key several seconds to restore the default settings when the

instrument works abnormally.

Multi-meter: the red and black multi-meter pen must insert the corresponding port.

Warnings:Instrument communication port is not permitted access circuit voltage over 6V,

otherwise damage the tester.

Warnings:Not allow insert multi-meter pen in the current

terminal to measure voltag

3.2 Instrument connection

3.2.1 IP camera connection

Power an IP camera with an independent power supply, then connect the IP camera to the IPC tester’s

LAN port, if the link indicator of the tester’s LAN port is green and the data indicator flickers, it means

the IP camera and the IPC tester are communicating. If the two indicators don’t flicker, check if the IP camera is powered on or the network cable is not functioning properly.

Page.17.

Note:1) If the IP camera requires PoE power, then connect the IP camera to the IP tester’sLAN port .

The tester will supply PoE Power for the IP camera. Click on the icon labeled POE to turn the PoE

Power off or on.

2) If use the tester’s menu to turn off the tester’s PoE power supply, the PoE switch and the power

sourcing equipment are allowed to connect to the tester’s PSE port, and the PoE power will be supplied

to the IP camera by the tester’s LAN port. On this condition, the tester cannot receive data from IP

camera, but the computer connected to the PoE switch can receive the data via the the tester.

Warning: Poe switch or PSE power sourcing equipment only can be connected to tester “PSE

IN” port, otherwise will damage the tester.

Page.18.

3.2.2 Analog camera connection

(1) ) Connect the camera's video output to the IP tester’s VIDEO IN. The image will display on the

tester after pushing the PTZ icon (2) CCTV IP Tester “VIDEO OUT” interface connect to the Video input of monitor and optical video transmitter and receiver, the image display on the tester and monitor (3) Connect the camera or the speed dome RS485 controller cable to the tester RS485 interface ,(Note positive and negative connection of the cable). Support RS232 PTZ controller ,connect the RS232cable to RS232 interface of the tester

3.2.3 HD Coaxial camera connection

* SDI, CVI, TVI, AHD camera are classified as HD coaxial cameras. Hereby the following instruction of how to connect SDI camera to the tester is also applied to CVI, TVI, and AHD camera.

Page.19.

(1) Connect the SDI camera's video output to the IP tester’s “SDI IN” interface, the image will display on the tester. The tester only come with SDI input interface. There is no SDI output interface.

(2) Connect the SDI camera or the speed dome RS485 controller cable to the tester RS485 interface, (Note positive and negative connection of the cable).Support RS232 PTZ controller; connect the RS232 cable to RS232 interface of the tester.

3.3 OSD menu Press the key 2 seconds to turn on Press the key again to turn off short press the key to enter sleep mode, press it again to test. If tester works abnormally and cannot be turned off , Press the key several seconds to turn off, the tester reset. Select Icons to enter, if quit, please click

Click SD card, install or remove SD card.

Page.20.

Click SD card, install or remove SD card.

Press function icon seconds, tip: whether moves this icon to APPS file, if some function not be often used, can move these function icons to APPS.

To move an app icon to the “APPS” folder, press and hold until the “move to apps directory” appears

on the screen then press OK to move it or Cancel

Page.21.

In APPS file, Select icon and press it for seconds, tip: whether move the file to the desktop?

3.3.1 IP discovery

Press IP discover ,tester auto-scan the whole network segment IP, as well as

auto-modify the tester‘s IP to the same network segment with the scanned camera's IP.

Page.22.

Local IP：Tester’s IP address, Tester can auto-modify the tester‘s IP to the same network segment with the scanned camera's IP

Discovery IP：Connected tester equipment’s IP address. If the camera connected to the tester

directly, tester will display the camera’s IP address, if tester connects to Local Area Network, it displays the current IP address.

Temp IIP：after searching IP address, the modified tester’s IP address will not be saved, if you do not select “Temp IP,” the modified tester’s IP address will auto-save after searching.

Start：PING function, Click "Start", can PING camera’s IP, Rapid ONVIF:Rapid ONVIF Quick link IPC TEST: IPC TEST Quick link Applicability：Using IP discovery app ,you don’t need to know the first two digits of

camera’s IP address , it can auto-scan the whole network segment IP, and auto-modify tester’s IP address , greatly improved engineering efficiency .

3.3.2 Video monitor test

Analog camera test and PTZ control, click icon to enter

Page.23.

Display the input video image, click the top menu bar icon to enter video level meter, (PEAK level, SYNC level, COLOR BURST measurement)

Select relative function on the right side Toolbar to operate , functions including “Photos”, “Snapshot” , “Record” , “Playback” , “PTZ” , “Set” ,

Click , or press to quit. Click the screen twice quickly, can be full zoom in on the touch screen.

(1) PTZ controller parameter setting

Select and click icon “PTZ”, to enter PTZ setting:

Page.24.

A. Protocol Use the up and down arrow keys to move the yellow cursor to the “protocol ”, set corresponding Protocol and support more than thirty PTZ protocols. Such as Pelco-D,Samsung,Yaan,LiLin,CSR600,Panasonic,Sony-EVI etc.

B. Port

Click and move, to “port” Select the communication port for the PTZ camera controlling (RS232/485) C. Baud

Move the yellow cursor to “Baud”, Select the baud rate according to baud rate of the PTZ

camera.(150/300/600/1200/2400/4800/9600/19200/57600/115200)

D. Address

Set the ID according the ID of PTZ camera (0~254), the setting address data must be consistent the speed dome address.

E. Pan speed: Set the pan speed of PTZ camera (0~63) F. Tilt speed: Set the tilt speed of PTZ camera (0~63) G. Set preset position (Set PS) Click and select “Set PS”, set and save preset position number(1~128), H. Call the preset position (Go ps)

Click and select “Set PS”, set and save preset position number (1~128), click “sure” to save, Call some special preset number, can call the dome camera menu

Check and set the protocols, address, interface and baud, all must be consistent with the dome camera,

then the IPC tester can test .After setting the parameter, the tester can control the PTZ and lens To control PTZ by screen touch: Tap left, right, upward and downward on the touch screen to control the PTZ rotation direction. By two fingers move outward and inward on the touch screen to zoom in and out the PTZ.

Page.25.

PTZ Control:

Press the key control the PTZ direction of rotation Press the key or , to switch on or turn off the aperture.

Press the key or , adjust the focus manually Press the key or , manually adjust the zoom (2) Video and storage setting Click icon “set”,to enter and set analog video image brightness , contrast, color saturation, as well as the file storage way after snapshot and recording, support auto-storage and manual storage. When select manual storage, user can name and store the files.

(3) 4 x zoom image display and Video out

When image input, press to enter “zoom”, press it again to quit. Using the touch screen to control PTZ camera movement: Tap left, right, upward or downward on the video image to move the PTZ camera in a desired direction.

Page.26.

+ 80 hidden pages