Avycon AIVO-35T User Manual

Download

HD-TVI / Network tester

User’s Manual

（AIVO-35T）

Thank you for purchasing AIVO-35T All-in-one tester. Please read the manual thoroughly before

use AIVO-35T All-in-one tester for the first time.

Please read the「Safety Information」section in the manual carefully. Please keep the manual in safe place for the future reference. Keep the S/N label for the future RMA purpose. Product without S/N label will be charged for

RNA repair service.

If there is any question or problem using AIVO-35T All-in-one tester, please contact AIVO

technical support.

Content

1. Safety information ----------------------------------------------------------------------------------------------------- 1

2. IP Camera Tester Introduction --------------------------------------------------------------------------------------- 2

2.1 General --------------------------------------------------------------------------------------------------------- 2

2.2 Features -------------------------------------------------------------------------------------------------------- 3

2.3 Function -------------------------------------------------------------------------------------------------------- 5

2.4 Packing list -------------------------------------------------------------------------------------------------- 11

2.5 Function interface ------------------------------------------------------------------------------------------ 12

3. Operation -------------------------------------------------------------------------------------------------------------- 16

3.1 Installing the Battery --------------------------------------------------------------------------------------- 16

3.2 Instrument connection ------------------------------------------------------------------------------------- 17

3.2.1 IP camera connection --------------------------------------------------------------------------- 17

3.2.2 Analog camera connection --------------------------------------------------------------------- 18

3.2.3 HD Coaxial camera connection --------------------------------------------------------------- 18

3.3.1 Video monitor test (PTZ control) ------------------------------------------------------------- 22

3.3.2 Color-bar generator (TV OUT) --------------------------------------------------------------- 31

3.3.3 ONVIF --------------------------------------------------------------------------------------------- 32

3.3.4 IP camera test ------------------------------------------------------------------------------------- 41

3.3.5 TVI camera test ---------------------------------------------------------------------------------- 44

3.3.6 IP address scan ----------------------------------------------------------------------------------- 49

3.3.7 PING Test ----------------------------------------------------------------------------------------- 49

3.3.8 Cable test ------------------------------------------------------------------------------------------ 50

3.3.9 Port finder ----------------------------------------------------------------------------------------- 51

3.3.10 Data monitor ------------------------------------------------------------------------------------ 52

3.3.11 Digital Multi-meter（*Optional ） -------------------------------------------------------- 53

3.3.12 Media Player ------------------------------------------------------------------------------------ 59

3.3.13 Audio player ------------------------------------------------------------------------------------ 60

3.3.14 LED Flashlight --------------------------------------------------------------------------------- 60

3.3.15 POE Voltage Meter -------------------------------------------------------------------------- 62

3.3.16 Calculator ---------------------------------------------------------------------------------------- 62

3.3.17 Browser ------------------------------------------------------------------------------------------ 62

3.3.18 IP camera viewer ------------------------------------------------------------------------------- 63

3.3.19 DC12V power output -------------------------------------------------------------------------- 65

3.3.20 Application tools ------------------------------------------------------------------------------- 66

3.3.21 APPS Tools ------------------------------------------------------------------------------------- 75

3.3.22 System Set --------------------------------------------------------------------------------------- 76

3.3.23 Update -------------------------------------------------------------------------------------------- 79

3.4 DC12V 1A power output --------------------------------------------------------------------------------- 79

3.5 Audio test ---------------------------------------------------------------------------------------------------- 80

4. Specifications --------------------------------------------------------------------------------------------------------- 81

4.1 General Specifications ------------------------------------------------------------------------------------- 81

4.2 Multi-meter specifications -------------------------------------------------------------------------------- 83

4.3 Optical power meter specifications --------------------------------------------------------------------- 86

4.4 Visual fault locator specifications ----------------------------------------------------------------------- 86

1 Safety information

The tester is intended to use in compliance with the local rules of the electrical usage and avoid to apply at the places which are inapplicable for the use of electrics such as hospital, gas station etc.

◆ To prevent the functional decline or failure, the product should not be sprinkled or damped.

◆ The exposed part of the tester should not be touched by the dust and liquid.

◆ During transportation and use, it is highly recommended to avoid the violent collision and vibration

of the tester, lest damaging components and causing failure.

◆ Don’t leave the tester alone while charging and recharging. If the battery is found severely hot, the

tester should be powered off from the electric source at once. The tester should not be charged over 8 hours.

◆ Don’t use the tester where the humidity is high. Once the tester is damp, power off immediately and move away other connected cables.

◆ The tester should not be used in the environment with the flammable gas.

◆ Do not disassemble the instrument since no component inside can be repaired by the user. If the

disassembly is necessary indeed, please contact with the technician of our company.

◆ The instrument should not be used under the environment with strong electromagnetic interference.

◆ Don’t touch the tester with wet hands or waterish things.

◆ Don’t use the detergent to clean and the dry cloth is suggested to use. If the dirt is not easy to

remove, the soft cloth with water or neutral detergent can be used. But the cloth should be tweaked sufficiently.

About Digital Multi-meter

◆ Before using, you must select the right input jack, function and range.

◆ Never exceed the protection limit values indicated in specifications for each range of measurement.

◆ When the tester is linked to a measurement circuit, do not touch unused terminals.

◆ Do not measure voltage if the voltage on the terminals exceeds 660V above earth ground.

◆ At the manual range, when the value scale to be measured is unknown beforehand, set the range

selector at the highest position.

◆ Always be careful when working with voltages above 60V DC or 40V AC, keep fingers behind the probe barriers while measuring.

◆ Never connect the meter with any voltage source while the function switch is in the current, resistance, capacitance, diode, continuity, otherwise it will damage the meter.

◆ Never perform capacitance measurements unless the capacitor to be measured has been discharged fully.

◆ Never measure any of resistance, capacitance, diode or continuity measurements on live circuits.

Visual laser sources

When you turn on visual laser sources, please don’t stare at it, or will damage to eyes. When not using it, Please turn it off and cover the protective cap.

2. IP Camera Tester Introduction

2.1 General

The 3.5 inch touch screen IP camera monitor and tester is designed for maintenance and installation of IP cameras and analog cameras as well as other security equipment. The 480x320 resolution enables it to display network HD cameras and analog cameras in high resolution. The unit supports many ONVIF PTZ and analog PTZ control. The combination of touch screen and key buttons make the IP camera tester very user- friendly.

The tester is also a great tool for Ethernet network testing. It can test PoE power voltage, PING, and IP address searching. You can use the blue cable tracer to locate individual connected cables from a bundle of cables. Test LAN cable for proper connection termination. Other functions include LED Flashlight, DC 12V 1A power output and much more. Its portability, user-friendly design and many other functions make the IP tester an essential tool for all installers or technicians.

2.2 Features

 3.5inch 480×320 touch screen, easy to operate.  ONVIF IP camera video testing.

 Compatible with H.264/MPEG4/MJPEG IP cameras, such as Dahua, HIKVISION, and ACTI.

Customized service is available.

 Built in Wi-Fi: receives video from wireless cameras or ONVIF cameras connected to the

network.

SDI Digital camera image display, record and screen snapshot （* Optional ）

 HD CVI camera image display, zoom ,video record and playback ,Coaxial PTZ control and

call camera OSD menu（* Optional ）

 HD TVI camera image display, zoom ,video record and playback ,Coaxial PTZ control and

call camera OSD menu

 AHD camera image display, zoom ,video record and playback ,Coaxial PTZ control and call

camera OSD menu（* Optional ）

 Analog camera video display. Auto adapts and displays the video in NTSC/PAL formats  Support more than 30 protocols, such as PELCO-P，PELCO-D,SAMSUNG etc  PEAK video signal level, SYNC signal level, Color burst Chroma level measurement, test

video signal attenuation（* Optional ）

 Video image digital zoom to view the image in greater detail.  Snapshot function allows you to save the current image as a JPG file in the SD card.  Video recording and playback.

 LED Flashlight.

 4GB Micro SD card included  LCD screen brightness/contrast/color Saturation adjustable  Visual fault locator , to test fiber’s bending and breakage（* Optional ）  Optical power meter ,test fiber loss and value（* Optional ）  Digital Multi-meter , DC and AC voltage measurement, Resistance measurement （*

Optional ）

 Enhanced Color bar generator: PAL/NTSC multi-system color bar video generator

(Eight-system switchable, transmit/receive eight-system colorful images).

 Cable tracer by sending an audio signal, enables the blue cable tracer to find the connected

cable from a bundle of cables.（* Optional ）

 Ping test: PING is the most conventional network debugging tool; it is used for testing if the

connected IP camera or other network equipment’s Ethernet port is working normally and the

IP address is correct.

 In digital IP surveillance applications, if the IP camera’s IP address is not known; the device

cannot be used. An IP address scan can quickly search for the connected IP camera or other

network device’s IP address

 The PoE voltage test can test for PoE voltage when a POE switch is supplying POE power to an

IP camera

 TDR cable test, test cable short-circuit and short-circuit（* Optional ）  Cable test: Tests LAN cable sequence of wires  Support RS485,Rate 600 ～ 115200bps adjustable  PTZ protocol analysis, control protocol command displays to check RS485 transmission

whether is normal, easy to find the fault device  PTZ control. Pan/tilts the P/T unit, zooms in/out the lens, adjusts the focus, aperture and

Sets and the preset position

 DC12V 1A output power for cameras  Audio input t test.  3.7V 3000mAh,Lithium Ion Polymer Battery can last 10 hours for normal use after charging

for 4-5 hours. Remaining battery charge indicator

“*”Sign means the function Optional

2.3 Function

2.3.1 Touch screen and OSD menu

The IP camera tester combines touch screen control and physical buttons. This combination makes the tester very user friendly. The test meter allows you to move the function icons from the tester’s main menu to the APPS tool folder or move them back to customize the main menu

2.3.2 WiFi

With built in WiFi, you can view the video from a wireless camera (ONVIF or customized camera) or

connect to a Wireless network.

2.3.3 IP camera test

The device is designed for ONVIF IP camera testing. It can display the image from an IP camera and change the IP address. The 3.5 inch 480x320 screen display allows the user to view the image with a sufficient screen size.

With the ONVIF tool, you can display the image from an IP camera and use the PTZ functions. Currently the IP camera tester supports more than 70 brands' IP cameras, such as most, ACTi, Dahua, Hikvision, Samsung, Honeywell and many more. OEM service is available. Users can send us the ip camera mobile apps for our engineers try to add the protocol to the tester.

2.3.4 SDI camera test （* Optional）

SDI digital video surveillance testing, support 720p 60fps / 1080p 30fps / 1080i 60fps digital camera image test and video image zoom, record, screen snapshot, Photo viewer and playback.

2.3.5 CVI camera test（* Optional ）

CVI camera tester, support720p 25,30,50,60fps/1080p 25,30fps,when CVI signal input,HD CVI camera image display, zoom, view photos, video record and playback, Coaxial PTZ control and call up the camera OSD menu.

2.3.6 TVI camera test

TVI camera tester support 720p 25,30,50,60fps/1080p 25,30fps, when TVI signal input,HD TVI camera image display, zoom,view photos,video record and playback,Coaxial PTZ control and call up the camera OSD menu.

2.3.7 AHD camera test（* Optional ）

AHD camera tester, support 720p 25,30fps/ 1080p 25,30fps, when AHD signal input, AHD camera image display, zoom ,view photos ,video record and playback ,Coaxial PTZ control and call camera OSD menu.

2.3.8 Analog camera test

Displays an analog camera image on the 3.5 inch 480*320 resolution LCD screen. Supports PAL & NTSC formats. The LCD screen's back light brightness, video image brightness, contrast and color saturation are all adjustable.

2.3.9 Video level meter（* Optional ）

Perform NTSC and PAL video amplitude signal measurements for PEAK to PEAK, SYNC levels and COLOR BURST Chroma level. Video signal PEAK to PEAK level: For NTSC format, the video signal level is 140±15IRE For PAL format, the video signal level is 1000±200mV If the level is too low, it will cause the image to lose quality and limit the distance it will travel over cable. If the level is too high, it will lead to wash out of the image SYNC level: Testing the amplitude of the video sync pulse to verify if the video level is correct. For NTSC format, the SYNC level is 40 ± 5IRE For PAL format, the SYNC level is 300 ± 35mV If the level is too low, it will cause the image to not frame out properly. If the level is too high, it will lead to a poor quality COLOR BURST level: Testing the color burst level will determine if the burst signal is sufficient to trigger the displays color producing circuit. Burst will diminish in amplitude over longer cable runs and

can get fall below the threshold for the video display to show a color image. For NTSC format, the Chroma standard level is 40 IRE For PAL format, the Chroma standard level is 280mV If the Chroma level is too low, the color will not be as deep, and some details of the image will get washed out. If the Chroma level is too high, there will be spots on the image. If the coaxial cable is too long, it will reduce the chroma level

2.3.10 PTZ controller

Display the input video images. Pan/tilt the P/T unit and zoom in/ out the image. Setup the controlling parameters like protocol, communication port, baud rate, PTZ ID, pan/tilt speed; set and call preset position.

2.3.11 Enhanced Color bar generator

The tester sends out color bars via its BNC output to the monitor. This is used to test for a problem in the cable going from the camera back to the monitoring area

2.3.12 DC12V 1A power output

Power the camera with DC12V (1A) power output from the tester. It is helpful for demo and testing

when the power supply is not available

2.3.13 Audio testing

Test the audio from mic level input devices. Connect the tester and mic level device with the audio cable. Supports record and save the audio.

2.3.14 Cable tester

Test LAN cable or telephone cable. Connect LAN cable or telephone cable with the CCTV tester and cable tester. And then the connecting status, cable type and the sequence of wires will be displayed, as well as display the serial number of the cable tester kit.

2.3.15 PTZ data analysis

Search the Control protocol code from Multifunction keyboard or DVR by RS485 interface, test the PTZ control command data whether received anomaly and RS485 data transmission.

Screen displays 16 hexadecimal codes such as PELCO-P:A0 00（Add） xx xxxxxx AF xx PELCO-D:FF 01（Add）xx xxxxxxxx

2.3.16 Digital Image zoom on the monitor

Set image zoom up to 4X to get a closer look at all the image detail. Supports analog and many IP

cameras

2.3.17 Video screenshot

Capture the video image, and save it as JPEG file in the SD card.

2.3.18 Record

Capture the video frames as JPEG file

2.3.19 Playback

The recorded files can play directly via Media player or under the function of “Playback”.

2.3.20 Cable tracer（ * Optional ）

Cable identification by use of an audio signal. This function enables the blue cable tracer to find the connected cable from a bundle of cables with an audio tone.

2.3.21 DHCP dynamic address assignment

Built in DHCP server: Dynamically assign IP address for the IP camera or network device.

2.3.22Access the dynamic IP address

The IP tester can directly access a dynamic IP address assigned from its DHCP server and use it as the tester's IP address. No need to set a IP address manually.

2.3.23 Multiple network IP Cameras Test

Supports Multi- segmented Static IP address setting which can simultaneously test different segments of

IP network cameras.

2.3.24 Network bandwidth testing

The network bandwidth test needs two IP testers to test bandwidth: one as a transmitter, the other as a receiver.

2.3.25 IP address scan

The IP address scan can quickly search for connected IP cameras or another network device IP address.

2.3.26 PING Test

PING is the most conventional network debugging tool; it is used for testing if the connected IP camera or other network equipment is working normally and the IP address is correct

2.3.27 Port Finder

The tester will send signals to make the connected PoE port flicker at a set frequency. This will enable the installer to easily and quickly find the connected port for an Ethernet cable.

2.3.28 PoE Test

Test the PoE voltage from a PoE switch. The unit will clearly display the voltage for each wire in an Ethernet cable.

2.3.29 Digital Multi-meter（* Optional ）

The tester built in highly stable and reliable 33/4 digit (6600) digital multi-meter. It is used for the DC and AC voltage measurement, AC and DC current measurement, Resistance measurement, Continuity test, Diode measurements, Capacitance measurement, Auto/Manual measuring range switching, relative value measurement and locking. It is easy operation and professionally accurate.

2.3.30 Visual fault locator（* Optional ）

Visual Fault Locator with 650nm wavelength can emit red laser sources to test multi-mode and single mode fiber’s bending and breakage, and Continuous light-emitting and 1HZ, 2Hz modulating light

output. It is indispensable tool in fiber project constructing, fiber net-work maintaining, optical

component manufacture and research.

2.3.31 Optical Power Meter（* Optional ）

The IP camera tester adopts the most advanced handheld instrument specific integrated chip , achieve ultra-low power operation, with the 3.5 TFT-LCD High-definition screen display ,five wavelength calibration points 1625nm,1550nm ,1490nm , 1310nm , 1300nm , 850nm.Linear or nonlinear optical power display, it can measure the optical power value, and also be used for Relative measurement of optical fiber link loss. It is necessary tool for fibre-optic communication, cable television system and security system maintenance.

2.3.32 LED Flashlight

Press the LED On/Off button to use the LED flashlight.

2.3.33 Screen image rotates 180 degrees

You can manually rotate the display 180 degrees using the settings.

2.3.34 TDR cable open circuit and short circuit measurement（* Optional ）

TDR cable testing, accurately measure BNC cable, network cable, controls cable’s open circuit and short-circuits location. It improves working efficiency.

2.3.35 FTP Server

Start the tester’s Wi-Fi or connect the tester’s LAN port to the network. Once the tester is online, start its FTP Server and directly access files from the tester’s SD card. This also allows for the user to upgrade the tester firmware

2.4 Packing list

1). Tester

2). Adaptor DC12V 1A

3). Network cable tester

4). Polymer lithium ion battery （3.7V DC 3000mAh ）

5). BNC cable

6). RS485 cable

7). SC,ST connector（Only for optical power meter）

8). Multi-meter test leads one pair of red and black (only for the Multi-meter models)

9). Camera powering cable

10). Audio cable

11). TDR alligator clamp (only for TDR models)

12). Safety cord

13). Tool bag

14). User’s Manual

15) 4GB SD card

2.5 Function interface

Press more than 2 seconds, turn on or off the device ,short press to turn on or off the menu display

2 Set key

3 Menu key

4 Near focus: Focus the image nearby

5 Far focus: Focus the image faraway

6 TELE: zoom in the image

7 WIDE: zoom out the image

8 Open/set ,Confirm the setting of parameters, open or enlarge the aperture

Return/Close : Return or cancel while setting parameters of the menu, close or decrease the aperture

10 Upward, set function or add parameter. Tilt the PTZ upward

Rightward, select the parameter whose value will be changed. Add the value of the parameter. Pan the PTZ right

12 Leftward, select the parameter whose value will be changed

Downward, set function or reduce the value of the parameter. Tilt the PTZ downward

14 Open/set ,Confirm the setting of parameters, open or enlarge the aperture

15 Snapshot

16 Video record

17 LED lamp

18 Confirm key

Return/Close : Return or cancel while setting parameters of the menu, close or decrease the aperture

20 The power indicator: it lights green while the tester is powered on by the adapter

21 The data accepted indicator: it lights red while the data is being received

The RS485 data transmission indicator: it lights red while the data is being transmitted

The charge indicator: it lights red while the battery is being charged. As the charging is complete, the indicator turns off automatically

Top interface

Left interface Right interface

Video signal input（BNC interface）

Video signal output（BNC interface）/cable tracer interface ( Optional)

TDR cable test interface / TVI input (BNC interface)

DC12V1A power output , for provisional DC power supply

Not support RS232 communication

LED flashlight (lamp)

RS485 Interface: RS485communication for the PTZ

LAN test interface

PSE power sourcing equipment. Tests PoE voltage

Audio input

Reset key

UTP cable port: UTP cable tester port/ Cable tracer port

DC12V1.5A charging interface

Micro SD card removable (comes with 4GB, supports up to 32GB)

3. Operation

3.1 Installing the Battery

The tester has built-in lithium ion polymer rechargeable battery. The battery cable inside battery cabin should be disconnected for safety during transportation! Usually it doesn’t need to disconnect the cable at the normal use Pressing the key continuously can power on or off the tester.

Notice: Please use the original adaptor and connected cable of the device!

When the battery icon is full or the charge indicator turns off automatically, indicate the battery

charging is completed

When the Charge Indicator turns off, the battery is approximately 90%

Charged. The charging time can be extended for about 1 hour and the charging time within 12 hours will not damage the battery.

Notice :Press the key several seconds to restore the default settings when the

instrument works abnormally.

Multi-meter: the red and black multi-meter pen must insert the corresponding port.

Warnings: Instrument communication port is not permitted access circuit voltage over 6V,

otherwise damage the tester.

Warnings: Not allow insert multi-meter pen in the current terminal to measure voltage

3.2 Instrument connection

3.2.1 IP camera connection

Power an IP camera with an independent power supply, then connect the IP camera to the IP tester's LAN port, if the link indicator of the tester's LAN port is green and the data indicator flickers, it means the IP camera and the IP tester are communicating. If the two indicators don't flicker, check if the IP camera is powered on or the network cable is not functioning properly.

Warning: PoE switch or PSE power sourcing equipment only can be connected to tester “PSE

IN” port, otherwise will damage the tester.

3.2.2 Analog camera connection

(1) The camera or dome video output is connected to CCTV IP Tester VIDEO IN,the image display on the tester . (2) IP Tester “VIDEO OUT” interface connect to the Video input of monitor and optical video transmitter and receiver, the image display on the tester and monitor (3) Connect the camera or the speed dome RS485 controller cable to the tester RS485 interface (Note positive and negative connection of the cable)

3.2.3 HD Coaxial camera connection

*TVI camera are classified as HD coaxial cameras. Hereby the following instruction of how to connect SDI camera to the tester is also applied to TVI camera.

(1) Connect the SDI camera's video output to the IP tester’s “SDI IN” interface, the image will display on the tester. The tester only come with SDI input interface. There is no SDI output interface. (2) Connect the SDI camera or the speed dome RS485 controller cable to the tester RS485 interface (Note positive and negative connection of the cable).

3.3 OSD menu

 Press the key 2 seconds to turn on  Press the key 2 seconds to turn off  short press the key to enter sleep mode, press it again to test if tester work abnormally

and cannot be turned off , Press the key several seconds to turn off, the tester reset

Select Icons to enter, if quit, Please click

Click SD card, install or remove SD card

Press function Icons seconds, tip: whether move this icon to APPS file, if some function not be often

used, can move these function icons to APPS.

To move an app icon to the “APPS” folder, press and hold until the “move to apps directory” appears

on the screen then press OK to move it or Cancel

 Click icon “APPS” tool, to show all collected function icons, Click , back to the tester’s

main menu

In APPS file, Select icon and press it for seconds, tip: whether move the file to the desktop?

3.3.1 Video monitor test (PTZ control)

Analog camera test and PTZ control, click icon to enter

Display the input video image, click the top menu bar icon to enter video level meter, (PEAK level, SYNC level, COLOR BURST measurement) Select relative function on the right side Toolbar to operate , functions including “Photos”, “Snapshot” ,

“Record” , “Playback” , “PTZ” , “Set” , Click to quit, or press back to menu. Click the screen twice quickly, can be full zoom in on the touch screen.

3.3.1.1 PTZ controller parameter setting

Select and click icon “PTZ” ,to enter PTZ setting:

A. Protocol Use the up and down arrow keys to move the yellow cursor to the “protocol ”, set corresponding Protocol and support more than thirty PTZ protocols. Such as Pelco-D,Samsung,Yaan,LiLin,CSR600,Panasonic,Sony-EVI etc.

B. Port

Click and move, to “port” Select the communication port for the PTZ camera controlling (RS485) C. Baud Move the yellow cursor to “Baud”, Select the baud rate according to baud rate of the PTZ camera.(150/300/600/1200/2400/4800/9600/19200/57600/115200)

D. Address

Set the ID according the ID of PTZ camera (0~254), the setting address data must be consistent the speed dome address. E. Pan speed: Set the pan speed of PTZ camera (0~63)

F. Tilt speed: Set the tilt speed of PTZ camera (0~63) G. Set preset position (Set PS) Click and select “Set PS”, set and save preset position number (1~128), H. Call the preset position (Go ps)

Click and select “Set PS”, set and save preset position number (1~128), click “sure” to save, Call some special preset number, can call the dome camera menu

Check and set the protocols, address, interface and baud, all must be consistent with the dome camera, dome camera, then the IPC tester can test .After setting the parameter, the tester can control the PTZ

and lens To control PTZ by screen touch: Tap left, right, upward and downward on the touch screen to control the PTZ rotation direction. By two fingers move outward and inward on the touch screen to zoom in and out the PTZ.

 Press the key control the PTZ direction of rotation  Press or to switch on or turn off the aperture.

 Press or adjust the focus manually  Press or manually adjust the zoom

3.3.1.2 Video and storage setting

Click icon "set" ,to enter and set analog video image brightness , contrast, color saturation, as well as the file storage way after snapshot and recording, support auto-storage and manual storage. When select manual storage, user can name and store the files.

3.3.1.3 4 x zoom image display and Video out

When image input, press to enter “zoom” ,press it again to quit. Using the touch screen to control PTZ camera movement: Tap left, right, upward or downward on the video image to move the PTZ camera in a desired direction. Stretch two fingers outward or inward on the touch screen to zoom the image in or out.

if not by touch screen to operate ,press the key to zoom out , press the key to zoom in, press upward and downward key to move the image

For analog video input, as the resolution is 720*480, it is normal that the zoom in image is not

clear. But for network digital video input, as it supports resolution up to 1280*960, the zoom in image is still very clear. This is very helpful for IP camera installation.

3.3.1.4 Snapshot

Click the icon "Snapshot ", when the video in, to take a picture and save the current video frame in the SD card as JPEG file. If the unit is set to the manual mode an "Input Name" pop up box will appear and you can enter a title for the snapshot. If the unit is set up to automatically set file names, this box will not pop up.

3.3.1.5 Video record

When you click the "Record" icon, video starts recording. A red recording icon appears on the screen and begins to flash and a timer appears indicating the time elapsed for the video. Click on the "Record" icon again to stop recording and save the video file to the SD card. if select manual storage, before recording begins ,appears dialog box "Input Name" ,user-defined the files name(by Chinese character, English letter ,or digit) to store in SD card , tester will hereby store the files in SD card after recording ., if select “Auto-storage” ,tester will auto store the files in SD card after recording .

3.3.1.6 Photo

Click the icon "photo" to enter, click the selected thumbnail photo to display it on the screen. Double-tap the image you want to view to make it full screen. Double-click again the photo to return.

To rename or delete an image, click and hold on the file until this screen below appears

Click to close and return to PTZ controller.

3.3.1.7 Record playback

Click the "Playback" icon to view your recorded videos. Tap on the video file image you want to watch.

To rename or delete a video, click and hold on the file until this screen appears:

Video files also can play in the main menu “Video Player".

3.3.1.8 Video level meter（* Optional）

Click the icon to enter, the IP camera tester has adopted hardware high-speed sampling and processing technology, can perform both NTSC and PAL video amplitude signal measurements for PEAK to PEAK, SYNC level and COLOR BURST Chroma level. When an analog signal is fed into the meter, the tester displays the measurements on the bottom left corner of the screen.

While in PAL format, the unit will be mV, While in NTSC format, it will be IRE.

NTSC

Video signal level

140±15IRE

Chroma level( COLOR BURST)

40±5IRE

SYNC signal level

40±5IRE

PAL

Video signal level

1000±200mV

Chroma level( COLOR BURST)

300±35mV

SYNC signal level

300±35mV

Video signal PEAK to PEAK level: For NTSC format, the video signal level is 140±15IRE For PAL format, the video signal level is 1000±200mV If the level is too low, it will cause the image to lose quality and limit the distance it will travel over cable. If the level is too high, it will distort the image. SYNC level: Tests the amplitude of the video sync pulse to verify if the video level is correct. For NTSC format, the SYNC level is 40 ± 5IRE For PAL format, the SYNC level is 300 ± 35mV If the level is too low, it will cause the image to not frame out properly. If the level is too high, it will lead to a poor quality image. COLOR BURST level: Testing the color burst level will determine if the burst signal is sufficient to

trigger the displays color producing circuit. Burst will diminish in amplitude over longer cable runs and can get fall below the threshold for the video display to show a color image.

For NTSC format, the Chroma standard level is 40 IRE

For PAL format, the Chroma standard level is 280mV If the Chroma level is too low, the color will not be as deep, and some details of the image will become lighter. If the Chroma level is too high, there will be distortions on the image. If the coaxial cable is too long, it will reduce the Chroma level. Image loop test：Test video optical transmitter and receiver and video cable, connect one end to the tester “VIDEO OUT” port ,and the other end connected to “VIDEO IN” port, the signal send via “VIDEO OUT” port ,and received via “VIDEO IN” port , If the testing is ok, the tester displays several gradually dwindling photos on the desktop.

3.3.2 Color-bar generator (TV OUT)

Click to enter, the tester send the color bars from the “Video out” port ,Click the icon “PAL”, select “PAL/NTSC” output formats

Click the selected color-bars, testing image or single bar (red, green, blue, white or black). Double click

to full display on the screen and output, click to return main menu. Application A. When maintaining the dome camera, the tester sends out the color bar by its BNC output to the monitor at the monitoring center. If the monitor receive the color bar, it means the video transmit channel works normally. Meanwhile on the basis of the received color bar, the monitoring center can judge if transmission has loss or interference. B. The tester sends out the pure color bar (such as white and black color), to test the monitor whether

has bright or black dots C. The tester sends out video signal image to test if the image received by the monitor has excursion.

3.3.3 ONVIF

The Open Network Video Interface Forum (ONVIF) app is used to connect to ONVIF compliant IP

cameras only. If the IP camera's video stream is MPEG4, use the ONVIF (SD) mode. If your IP camera's video stream is H.264, use ONVIF HD (High Definition), HD mode cannot support MPEG4. While in SD mode, if the network camera resolution is 720P or higher 720P, the image display may be delayed. While in HD mode, if the network camera stream is H.264, the tester can fluently display the image up to 1080P.

Click icon to enter then tap either the "ONVIF" icon is for SD mode (MPEG4) and the "ONVIF

HD" icon is for HD mode (H.264).

Click icon to enter, the tester Auto-Scan different network segments ONVIF cameras, and list the camera name and address on the screen left. Some cameras not need user name and password to login, Please select “Non- verification” to login the camera.

If you select ONVIF SD or HD mode, the meter automatically scans different network segments for ONVIF cameras. It lists the camera name and IP address on the Device List. If no cameras appear under the device list, try clicking on the Refresh button

Click “refresh”, the IPC tester scanned ONVIF network camera on the internet. Click the camera in the list of devices, camera login window pops up. Input the camera’s username and

pass word. Some network cameras, does not require a user name and password authentication, check "non-verification" and then login the camera.

Click “device list” of the tester’s screen left, will shows the camera information and setting. Such as

“Device information”, “Time setting”, “Maintenance” “Network setting”, “User management”, “Live video”, “Image setting” etc. Some functions must camera's setting open to operate.

Live Video: Click "Live Video" to view the live video feed from the IP camera. To make the image full screen, double tap on the video. Stretch two fingers outward or inward on the touch screen to zoom the image in or out. If you want to zoom in or out ,please press the key tele and wide

ONVIF PTZ control: Tap the image in the direction you want the PTZ camera to move. Tap the left side of the image to move left, right to go right, up to go up and down to go down. Compatible IP PTZ cameras will rotate accordingly. PTZ rotation direction is displayed on top left corner of the image.

Video Streaming: Click “Video Set” to enter, set the IP camera decoding resolution, click “OK “to save.

Image setting: Click "Imaging Set" to adjust image brightness, saturation, contrast, sharpness and backlight compensation mode.

Profiles :Click"profiles", can view video streaming current configuration files, as well as switch between Major stream and minor stream .

Preview pictures:Quickly preview and zoom in or out pictures, automatically and manual refresh

Network setting: Click “Network Set” to change the IP address settings. Note: Some cameras are not fully ONVIF compliant and cannot support changing their IP address, so

there is no change after saving.

Zoom in image: press the key to enter the zoom mode. Press it again to exit zoom mode. When the image is enlarged tap left, right, up or down on the image to move the whole image on the screen

When the image is enlarged, if not operate on touch screen, it can operate by the keyboard ,press the key to zoon in , press the key to zoom out ,press upward and downward key to move image .

If it is network video input to the tester, as the tester supports resolution up to 1080p, the input

image will be very clear after it is enlarged. This is greatly helpful to help the installers to ensure the IP

camera’s video coverage and decide the IP camera’s install site. Image can only be enlarged on SD mode (The icon “ONVIF” is SD mode.) On the interface of “Live Video”, click “Video Menu”, appears toolbar: Snapshot, Record, Photo, Playback, PTZ, Set, etc.

Snapshot: Click “snapshot” to screen shots and storage if select manual recording ,appears dialog box “Please input the files name” , user-defined the files name(by Chinese character, English ,or digit ) to save in SD card, if select “Auto-recording”, the tester auto-recording the files after screenshots . Record: When you click the "Record" icon, video starts recording. A red recording icon appears on the screen and begins to flash and a timer appears indicating the time elapsed for the video. Click on the "Stop" icon to stop recording and save the video file to the SD card.

Set: Click icon “Set”, Photo and record function can select, if Auto-name, Photos and recording files Auto-storage, if manual, user define files name.

Playback: Click the "Playback" icon to view saved videos. Double click the video you want to play. Click to return to the last menu

To rename or delete a photo, click and hold on the file until this screen appears:

Video files can play in the Video player of the main menu

3.3.4 IP camera test

Click icons to enter IP camera test

The “IPC Test” app is used for IP cameras that are fully integrated by name with the IP tester . If the IP

camera's video stream is MPEG4, use the IPC Test (SD) mode. If your IP camera's video stream is H.264, use IPC HD (High Definition)

Display high-definition images, support snapshot, video record and playback. Currently, the IPC tester only support some brands’ specified IP cameras, the brands include Dahua , Hikvision, Kodak , Samsung, etc. OEM service is available. Clients can send us the IP camera or mobile APPS (Android version. APK files) for our engineers to try to add the protocol to the IPC tester.

Note:Currently, the IPC Test App only supports some brands' specific IP cameras; these include

specific models made by ACTI, AXIS, Dahua, Hikvision, Samsung, and many more. If the camera is not fully integrated, please use the ONVIF or RTSP apps.

IPC test interface

Local IP:This is the tester's IP address. Click "Edit" to enter "IP setting" and change the tester 's IP

address settings IP camera type :Click IP camera type, list Honeywell , Honeywell , Kodak,Tiandy, Aipu-waton,VVS, ACTi,WoshiDA IP camera etc. If the brand has offered official original protocols, Pls select camera

type, input IP camera address ,user name and password ,click” official” to enter the camera image

display interface(Currently, only support DAHUA official protocols )

IP Camera's address: Enter IP camera’s IP address , click “deploy” o add IP address of the Different

network segments, support multi- network segments’ IP camera test .

Click “Search” to auto-scan the IP camera’s IP address and display. It is better to directly connect IP

camera to the tester so that the tester will search out only one IP address. If the tester is connected to PoE switch, it will search out several IP address.

IPC User Name: Enter IP camera’s user name

IPC Password: Enter IP camera’s login password, if default enter password, not show relevant letters,

click “display” to show the password IPC Port No.: Select IP camera type, it default relative camera port number, and not need change. After setting, click “Enter” to enter image interface.

If IP address setting has error or IP camera is not connected.. The tester prompts “Network Error” Click to quit from image display and return to IP camera test interface.

Under the IPC Test , on the IP camera image display, there is “Video Menu” icon, click “Video

Menu”, appears toolbar: Snapshot, Record, Photo, Playback, PTZ, Set, etc. Please refer to ONVIF to use these functions

3.3.5 TVI camera test

HD TVI camera, TVI dome camera test and PTZ control, Click icon to enter

When tester receives HD TVI camera image, it will display the image’s resolution on the top bar. Double-taps on the screen to make the image displayed full screen. Tester supports resolution as follows 1280x720P 25FPS / 1280x720P30FPS / 1280x720P 50FPS / 1280x720P 60FPS 1920x1080P 25FPS / 1920x1080P 30FPS / 1920x1080P 50FPS / 1920x1080P 60FPS

More operation instructions (such as PTZ control, coaxial camera menu setting, snapshot, recording and playback etc), please refer to“3.3.6 CVI camera test” （1）PTZ control

1.1 Click the icon “PTZ” on the right toolbar to do the corresponding setting. “Port”: select coaxial control

Enter PTZ address to perform parameters setting

Operation instructions please refer to “3.3.1 PTZ (1) PTZ control parameters setting”

The PTZ address in the tester must be consistent with the dome camera or decoder, then the IPC

tester can test .After setting the parameter, the tester can control the PTZ and lens.

To control PTZ by screen touch: Tap left, right, upward and downward on the touch screen to control the PTZ rotation direction, PTZ cameras will rotate accordingly. By two fingers move outward and inward on the touch screen to zoom in and out the PTZ. PTZ control by press key button

 Press arrow keys to control the PTZ direction of rotation  Press the key to switch on or turn off the aperture.  Press the key , adjust the focus manually  Press the key ,manually adjust the zoom

1.2 RS485 control

Operation instructions ,please refer to “3.3.1 PTZ (1) PTZ control parameters setting” （2）Coaxial camera menu setting Click “Coaxitron” and select “camera menu”, can open the dome menu

Input calling dome camera menu address code, click “ok”, then press key button“ ”or click screen icon “ ”

Press arrow keys to set

(3)Snapshot, record, photo viewer and video playback, please refer to “3.3.1 Video monitor test”

(4)Save setting Click icon “Set” on the right toolbar to enter storage setting. Support auto-storage and manual storage. When select manual storage, user can name and store the files.

3.3.6 IP address scan

Connect the cable to the LAN port, click icon to enter, set initial IP and destination IP address,to the tester’s IP address network segment can be the same or different to the scanned network device’s network segment, then click the key “Start” to scan, quickly to search the IP address, also can input the IP address in the Port Number Scan to scan to port number ,check the tested device’s supporting port number and how many ports can support the device’s network communication..

3.3.7 PING Test

PING is the most conventional network debugging tool; it is used for testing if the connected IP camera or other network Equipment’s Ethernet port is working normally and the IP address is correct.

Connect a network cable to the LAN port and click the icon to open the PING tool. You can set your LOCAL (native) IP address, Remote IP address (e.g. IP camera), Packet count, Packet Size, Packet

time and Timeout. Press “Start” to start pinging. If the IP camera or network device is not configured properly or not plugged in, it will say “Destination host unreachable,” or have 100% packet loss. If the

tester connects to the device, the send and receive packets will have a 0% packet loss.

Application: PING testing is the most conventional network debugging tools. It is used for testing if the connected IP camera or other network equipment’s Ethernet port is working normally and the IP address is correct. It’s normal that the first data packet will be lost when test start.

3.3.8 Cable test

Click icon to enter

Test LAN cable or telephone cable. Connect LAN cable or telephone cable with the CCTV TESTERPRO and cable tester. And then the connection status, cable type and the sequence of wires as well as the serial number of the cable tester kit will be displayed. The number of the cable tester is 255 If need several different number other types cable testers, should pay the additional cost.

3.3.9 Port finder

Connect a network cable to the meter’s “LAN” port; click the icon to open the Port Flashing app. Click “Start”. The IP tester sends a unique signal to make the connected LAN port of the switch flash

If the tester and PoE switch are connected well, the LAN port of POE switch flash at special frequency, If not, no any changes on the LAN port

Application:

The tester will send special signals to make the connected LAN port flicker at special frequency, which will enable the installers to easily and quickly find the connected Ethernet cable. This function can prevent mistakenly insertion or disconnection non-corresponding cable to artificially interrupt network connection.

3.3.10 Data monitor

Please click icon to enter

Click “Setting” to choose the baud rate of RS485; it must be the same as the DVR or the Control

keyboard .The DVR or Control keyboard send the code to the tester, if it can be read, the protocol will

AC/DC

Voltage and current measurement state display

Auto- range

The Multimeter auto adjust the range by input signal or tested components

Data hold

Hold data

Relative

measurement

Display the relative measurement value Press the key to change display state

10A socket

In 10A current measurement state ,indicate use 10A socket

Over range

The current measurement value over the range, if in the Auto range state, to switch Auto.

shown on the upper right, like Pelco D, if not, like P:---

When the tester receives the code, Press the key to clear screen.

Though the RS485 port, display the PTZ control code of the multifunctional keyboard or the DVR. Controller can check the status of the RS485 transmission through the code on the display. (The RS485 communication rate must be the same.) Application: Check the RS485 communication states of the video optical transmitter whether normal. Engineer can analyze the protocol and check the data through the displayed code.

3.3.11 Digital Multi-meter（* Optional ）

1.Click icon to enter

2) SYMBOLS: U:DC Voltage Measuring A:DC Current Measuring Ω:Resistance Measuring :Diode Testing

U~:AC Voltage Measuring A~:AC Current Measuring

:Continuity Testing :Capacitance Measuring

⑶OPERATING INSTRUCTION

DC Voltage Measuring

a. Connect the black test lead to the “COM ” jack and the red test lead to the “V/Ω” jack.

b .Select U, enter the DC voltage measurement.

c. the tester default Auto range status ,by click “DC auto range” ,

press the key can select manual range and restore auto range . Manual range: 0.000V  6.600V range

00.00V  66.00V range

000.0V  660.0V range

000.0mV  660.0mV rang

AC Voltage Measuring

a. Connect the black test lead to the “COM” jack and the red test lead to the “V/Ω” jack. b. select U ~ , enter the AC voltage measurement. C. the tester default Auto range status, by click “AC auto range” d. Manual range can be select , press the key “NEAR” to restore Auto range e．Manual range: 0.000V  6.600V range

00.00V  66.00V range

000.0V  660.0V range

000.0mV  660.0mV range

DC Current Measuring (only manual range )

WARNING!

Shut down the power of the tested circuit, and then connect the meter with the circuit for measurement. a. Connect the black test lead to the “COM” jack and the red test lead to the “mA” jack for a maximum of 660mA current. For a maximum of 10A, move the red lead to the 10A jack. b．select A, enter the DC current measurement, the screen display “DC current ”,can select manual

range； c．Manual range: 0.000mA  6.6mA range

00.00mA  66.00mA range

000.0mA  660.0mA range

00.00A  10.00A range（use 10A socket）

d. Select the range to enter current measurement

Note:

 When only the figure “OL” is displayed, it indicates over range situation and the higher range has to

be selected.

 When the value scale to be measured is unknown beforehand, set the range selector at the highest

position.

 The maximum current of mA socket is 660mA; over-current will destroy the fuse, and will damage

the meter.

 The maximum current of 10A socket is 10A, over-current will destroy the meter, and will damage

the operator.

 In“ AC ” mode, only can input “AC ”, if not, will damage the meter.

Resistance Measuring

WARNING!

When measuring in-circuit resistance, be sure the circuit under test has all power removed and that all capacitors have discharged fully.

a. Connect the black test lead to the “COM ” jack and the red test lead to the “V/Ω” jack. b. to select Ω, enter the Ω measurement the tester default Auto range status, Press the key manually

select range ,Press “NEAR” to restore “Auto range” Manual range: (Connect the red lead to black leads, will display the measure range)

000.0Ω  660Ω range

0.000 KΩ  6.600KΩ range

00.00 KΩ  66.00KΩ range

000.0 KΩ  660.0KΩ range

0.000 MΩ  6.600MΩ range

00.00 MΩ  66.00MΩ rang

Continuity Testing

a. Connect the black test lead to the “COM” jack and the red test lead to the “V/Ω” jack.

b. to select , enter the continuity test, Connect test leads across two point of the circuit under testing. c. If continuity exists (i.e., resistance less than about 50Ω), built-in buzzer will sound.

Diode Testing

a. Connect the black test lead to the “COM” jack and the red test lead to the “V/Ω” jack. (the red lead

anode “+” )

b. to select , enter the diode testing. c. Connect test red lead across to the anode, the black lead to the cathode of the diode under testing. d. Connect test red lead across to the cathode, the black lead to the anode of the diode under testing. e .Tested diode, forward voltage low 30mv,there is sound indication ,then can finish the testing quickly without view the screen.

Capacitance Measuring

a. Connect the black test lead to the“ COM ” jack and the red test lead to the “V/Ω ” jack. b. Select “ ” to enter, enter the capacitance measurement.

c. The tester default auto range status, and manual range by press upward and downward key, Auto rang by press the key “NEAR” Manual range:0.000nF  6.600nF range

00.00nF  66.00nF range

000.0nF  660.0nF range

0.000uF  6.600μF range

00.00uF  66.00μF range

000.0uF  660.0μF range

0.000mF  6.600mF range

00.00mF  66.00mF range d. Before connect test leads across two sides of the capacitor under measurement, be sure that the

capacitor has been discharged fully.

Note:

a. The capacitance of a capacitor should be tested separately, should not test in

the installation of circuit.

b. To avoid electric shock, be sure the capacitors have been discharged fully before measuring the ca

pacitance of a capacitor.

c. While testing the capacitance of a capacitor to

660uF, the Max time will be 6.6 seconds, if the capacitor is leaked or damaged, the data can’t be read. The tester will be normal after disconnecting the capacitor.

Manual range and Auto range When testing, click “Range select " to change the value, click “Auto range “to enter Auto measurement

Data hold

Click “Hold data” to enter, the data be hold, the value is green. Press it again to quit.

Relative value measurement

Click “Relative “to enter ,the tester Auto-save the data, the displayed new measurement and relative value is red color. Press it again to quit

The hold function and the relative value be combined use, the display value is yellow

The meter protection  Voltage protection

You can’t input the voltage which more than 660V AC, it’s possible to show higher voltage, but it’s may destroy the inner circuit.

 Resistance,Continuity,Diode,PTC component Protection

Wrong input voltage,will Auto enter protection state , It only suitable for short and limit time work.

If input voltage over 600V, will damage the meter.

 mA current fuse range :250V 1A

if the current over the rated range ,fuse will melt to protect the meter .Please use the same model

when change the fuse, Please opens the battery cover to change.

Note: 10A socket without fuse protection, if over the current range

Wrong using the 10A socket to measure the voltage, will damage the meter.

3.3.12 Media Player

Click the icon to enter

The Media player can browse video and image files. It supports the video formats of MP4, H.264, MPEG4, and MKV. The IP Tester’s recorded files can play directly via the Media player. The Media player will automatically display the video files from the SD card. Click on the desired file to play. Click RETURN to exit. To rename or delete an existing file, press the file name for a few seconds until the screen below appears. You can then rename or delete the file by pressing the desired option.

3.3.13 Audio player

Click the icon to enter , the audio player only supports MP3 format Audio files.

3.3.14 LED Flashlight

It is convenient for the installation or maintenance in the evening or in the dark. Click icon to enter

While in the flashlight app, click the red button to turn on the LED lamp. Press it again to turn it off. If you don’t press the red button to shut off the lamp and press the button to exit the app, the lamp

will stay on. Click the Time Setting button to set a timer that will shut off the lamp.

3.3.15 PoE/PSE Voltage test

Click icon icon to enter the PoE voltage in line measurement app.

Connect a network cable from a PoE switch to the IP tester’s PSE IN port. Connect an IP camera or other PoE using node to IP tester’s LAN port, the PoE voltage and the cable’s pin connection status show on the screen.

Note:This test if for measuring the voltage being drawn by the PoE node and the IP tester must be between the PoE switch and the PoE node for this test to work. Note: The PoE switch must be connected to the PSE IN port. The powered device such as IP camera or other PoE node must be connected to the LAN port. Note: Do not connect PoE power supply equipment (such as a PoE switch) to the tester’s UTP/SCAN port; otherwise it will damage the tester.

3.3.16 Calculator

Click icon to enter

3.3.17 Browser

Click icon to enter Type in the camera’s IP address and press “Go” to access the IP camera’s interface.

NOTE: You will not be able to view live video in the web browser. For viewing video, use the

IP tester live camera view apps.

The IP camera and IP tester must be on the same network segment for the browser to interface with the camera. If they are not in the same segment, click the button or press “RETRUN” to exit. Open the “Settings” app from the main menu to change the IP tester’s network settings to match those of the IP camera.

3.3.18 IP camera viewer

In addition to the ONVIF app or the IPC Test app, you can use one of the mobile apps in the IPC Viewer folder to view IP camera video. If you cannot find your desired mobile apps, you can send us the mobile apps (Android version. APK files) for our engineers to install in the tester, if successfully installed, the tester will allow you to see the IP camera image by IP camera viewer.

Click icon “IP camera viewer” to enter, and set the mobile apps parameter to see the corresponding IP camera’s image.

Mobile apps displays IP camera’s image by software decompression, hereby the image may be not clear or fluent.

Note::The mobile apps are third party applications. Our company does not support these apps nor make any usage claims. We do not assume any legal liability

Click desktop icon several seconds, to uninstall this application

Click icon “update “ in the IPC viewer interface, to update mobile apps

3.3.19 DC12Vpower output

Click icon to enter DC 12V power output interface. To use the DC 12V power output function, click on the icon and change the switch “ON” or “OFF”.

If to click without prior to change the switch “ON” to “OFF”, the 12VDC power output will till stay on, and the icon”12V ON” appear on the top bar. Change the switch “ON” to “OFF” to shut off the 12VDC power output.

1 .Don’t input any power into the “DC12/1A OUTPUT” port of the IP camera tester to avoid

destroy.

2. Don’t output this DC12V/1A power to the DC12V/IN port of the IP camera tester to avoid destroy

3. The IPC tester power output is close to 1A, if the IP camera’s power is over 2V, the tester will auto enter protection mode. Disconnect all the connections of the tester and then connect the tester with power adaptor to resume the tester.

4. Make sure the tester is full charged or more than 80%, otherwise the tester will shows “low

power”, “not able to supply power”

3.3.20 Application tools

Click the icon to open the Application Tools folder. This folder contains useful apps such as Audio Recording, DHCP Server, Network test, Notepad, Link monitor and RTSP Player.

Audio Record: Connect an audio device t the IP tester’s audio input port. Click the icon to enter the Audio Recorder app. Click the red button to stop, and the unit will prompt you to save the recording.

Net work test (Ethernet bandwidth test) To use the Network tester, you will need two IP testers. One is used as a Server and the other as a Client. Both devices must be on the same network segment in order to communicate. Click the icon to

open the Network Tester app. Note: Network test results only used as a reference, For more accurate test , please use a professional Ethernet tester .

When test , need a tester or a computer installed Network Test Software as the Server, the other tester

sends packet test. The two testers must be in the same network segment.

1. Start the server: Click “Start Server” button to use the tester as a Server. It will display its IP address at the top of the screen.

2. Start send packet test::Using the other IP tester and type in the Server's IP address at the top right corner of the screen. This app is used to send packets for network speed testing. Click the “Start” button to send the packets and start testing.

Network bandwidth testing can also be tested with a computer using compatible network bandwidth testing software. Install network bandwidth testing software on a computer, as a test Client or Server, with tester mutual –testing. If computer as the server, the computer IP address is :192.168.0.89

Tester as Client, tester’s IP address is:192.168.0.230. The Server and the Client are at the same network segment, but with different IP address. Input Server’s IP address 192.168.0.89 in the tester and click “Start” to test network bandwidth.

Or tester as a Server, computer as test Client（select Client, input tester’s IP address to test）

When tester as Server, shows results:

DHCP server:

Click on the DHCP icon to open the DHCP server app. Select the “Start” check box at the top and make

any desired changes to the network settings. Click “Save” to start assigning dynamic IP addresses for IP cameras and other networked devices.

Click the “Refresh” button to check your Client list.

“Refresh” to check received IP address.

Notepad:

Click on the Notepad icon to open the Notepad app. Click the “Save” key to save the contents

pls click to view the notepad , all saving contents display. Click each record bar to show the details. Press the record bar for several seconds, prompt whether delete it

Link monitor :

Click the icon to open the Link Monitor app. This app is used to see if an IP address is occupied by other network devices. This will avoid new address conflicts.

Click “Add” and enter the desired IP address. To test different network segments, click the “Settings”

icon on the main menu and go to IP Settings and make the desired changes. Once the desired IP addresses are added to the Link Monitor list, click “Start”. If the IP address status shows a check mark the IP address is occupied. If the IP address status shows an X the IP address is available. Click “Stop” to stop the testing.

Application:

Add an IP camera or other network device to the current network group, the new IP address must not be occupied, otherwise it will cause IP conflicts and stop the equipment normal working. Link monitor can check if the new setting IP address is occupied.

RTSP Player :

The RTSP Player app will allow you to view the RTSP video stream from an IP camera. If you were unable to view your camera via the ONVIF or IPC Test apps, it is possible your camera will have an RTSP stream and you can view live video.

From the main menu, select the “APP Tool” folder and then select the “RTSP Player” to open the app.

If the IP camera uses MJPEG, select the RTSP icon. If the IP camera uses H.264, select the “RTSP HD” icon.

Local IP: This is the IP testers IP address. RTSP Add: This is where you can manually enter the IP camera’s RTSP URL or click on Search to

search the network for cameras that use an RTSP stream.

IPC Username: Enter the IP camera’s user name. IPC Password: Enter the IP camera’s password.

Once you have entered all the necessary information, select Enter at the bottom left to view the RTSP stream.

Note: in the event the ip tester does not auto detect the rtsp stream, refer to the specific camera manufacturer for the specific rtsp stream url. you may find this on line with a search of the camera model number and the word rtsp. Trace route:

Trace route is used to determine path of the IP packet access target. Note: Trace route testing results only for reference, for accurate test route tracking, Please use professional Ethernet tester.

Click to enter Trace Route

Input tracking IP address or domain name in the Remote Host IP. Set maximum hop count, normally default is 30

Click “start” to trace the goal address

3.3.21 APPS Tools

Click the icon to open the Tool Folder. You can move desktop icons into the Tools Folder by pressing on the icon for a few seconds until the screen below appears

You can also move an icon back to the desktop by pressing on the icon for a few seconds until it asks you if you want to move the icon back to the Desktop.

3.3.22 System Set

Click icon to enter

Language: Select your desired language: English, Chinese, Korean, Russian, Italian or Polish, etc. Date/Time: Set the Date/time IP setting: Manually set the IP address, Subnet Mask, Default Gateway, DNS address or select

“Dynamic allocation” to use DHCP. To test multiple network segments, click “Advanced” and then click “Add” to enter another IP address for the IP tester.

After setting an advanced IP address (refer to above photos), the tester can test two network segments (192.168.0.0) and (192.168.1.0). WLAN:Turn WiFi off or on by pressing the “Open the Wi-Fi” button. Once Wi-Fi is turned on, it will scan for wireless networks in your area. Select the desired wireless network SSID and enter your password to connect networks in your area.

Brightness::Set the desired brightness of the IP tester and adjust the sleep time settings. Volume: Set volume level. SD Card: Displays SD Card Capacity. You can also format the SD card or unmounts it before

removing it FTP serve: Once the IPC tester connects to a network, a computer can be used to read the SD card files via FTP.

Start the FTP server and then input the tester’s FTP address in the PC’s address bar. (ftp: as:ftp://192.168.0.233:2121) This will enable the PC to read, copy and edit the files from the SD card without the use of SD card reader

Version information: This displays the version information for each application. Screen rotation: Click on “Screen Rotation” to flip the IP tester’s display 180 degrees. This function is

very convenient for the user to connect the LAN cable on the bottom of the unit without having to flip the unit itself PTZ address scan: You can toggle the PTZ Address scan off or on before entering the “PTZ controller” app. This needs to be turned on in order to use the PTZ Scan feature of the PTZ app. Turn off option: If you select “Fast turn off”, the tester will shut down faster but data will not saved. To avoid unnecessary problems, it is recommended not to use the “Fast turn off” option

3.3.23 Update

Click to enter

If there are applications for updating, the applications will be displayed on the interface. Click the relevant applications to update to the latest version.

3.4 DC12V 1A power output

Touch function ,enter power output interface

Click the switch “OFF” to“ON” to turn on DC12V 1A power output function.. The smaller end of the supplied converter cable connects to the tester’s DC12V/1A OUTPUT and the other end connects to the camera’s power input. Power output function is mainly used in the camera field demonstration and testing, meanwhile, for some camera installation sites, if there is no power outlet for the adapter to power the camera, the tester can offer temporary power for it. But we do not suggest tester supply power for a long time.

Notice:

a. Don’t input any power into the “DC12/1A OUTPUT” port of the IP camera tester to avoid

destroy. man-made damage is not within the Company’s warranty

b. Don’t output this DC12V/1A power to DC12V/ IN port to avoid destroy. otherwise the tester will

damage, and man-made damage is not within the Company’s warranty.

c. The IPC tester power output is close to 1A, if the IP camera’s power is over 1A, the tester will

auto enter protection mode. Disconnect all the connections of the tester and then connect the tester with power adaptor to resume the tester.

d. Make sure the tester has a sufficient charge otherwise the tester will not able to provide enough

output power.

3.5 Audio test

You can test the audio input from audio pickup devices by connecting the audio pickup device to the IP tester with the supplied audio cable. Support audio record and storage

4. Specifications

Model

IP Camera tester【*】models Optional

Display

3.5 inch Capacitive touch screen , resolution 480（RGB）x 320

Network port

10/100M auto adapt,RJ45

SDI camera test

* (Optional)

1 channel SDI IN BNC Input, Support resolution 720p 60fps / 1080p 30fps /1080i 60fps

CVI camera test

*（Optional）

1 channel CVI in（BNC interface, resolution max 720p 25,30,50,60fps / 1080p 25,30fps

TVI camera test

1 channel TVI in（BNC interface, resolution max 720p 25,30,50,60fps / 1080p 25,30fps

AHD camera test

*（Optional）

1 channel AHD in（BNC interface, resolution max 720p 25,30fps / 1080p 25,30fps

WIFI

Built in WIFI,speeds150M, allows you to connect to a wireless network and view IP camera

IP camera type

ONVIF,ONVIF PTZ, Dahua IPC-HFW2100P, Hikvision DS-2CD864-E13, Samsung SNZ-5200, Tiandy TD-NC9200S2, Kodak IPC120L, Honeywell HICC-2300T, RTSP Viewer. Customized welcome

Video input/output

1 channel BNC input & 1 channel BNC looped output, NTSC/PAL (Auto adapt)

Video level test:

Video signals measured in IRE or mV

Video level meter

* (Optional)

PEAK video signal level, SYNC signal level, Color Burst chroma level measurement

Zoom image

Supports Analog and IP camera image zooming & movement

Snapshot, Video record and

Capture still images and record live video. Media player will view photos and playback video

4.1 General Specifications

playback

12V/1Apower output

Output DC12V/1A power for camera

Audio test

1 channel audio signal input, test whether sound normal, supports record and save audio

PTZ control

Support RS485 control, Baud 600-115200bps, Compatible with more than 30 protocols such as PELCO-D/P, Samsung, Panasonic, Lilin, Yaan, etc

Video signal generator

Output one channel PAL/NTSC color bar video signal for testing monitor or video cable.(red, green ,blue, white and black color )

color bar generator

Local side PC can login the tester, send the signal by network ,test network connection communication whether normal

UTP cable tester

Test UTP cable connection status and display on the screen. Read the number on the screen

Data monitor

Captures and analyzes the command data from controlling device,also can send hexadecimal

Network test

IP address scan, link scan, and Ping test. Quickly search the for IP camera’s IP address on your network

Cable search * (Optional)

Find a connected cable from a bundle of cables using audio tones

PoE test

Measures PoE switch voltage and displays pin configuration

Digital Multimeter

* (Optional)

AC/DC Voltage,AC/DC current,Resistance,Capacitance,Data hold,Relative measurement,Continuity testing . Testing speed: 3 times/ seconds,Data range -6600～+6600.

Optical power meter * (Optional)

Calibrated Wavelength(nm) :850/1300/1310/1490/1550/1625nm Power range(dBm) :-70～+10dBm

Visual fault locator

* (Optional)

Test fiber’s bending and breakage ( SM and MM fiber)

TDR cable test * (Optional)

Cable open circuit （breakpoint） and short circuit measurement(BNC cable, Coaxial cable, Cat5/6, telephone cable)

POWER

External power supply

DC 5V(1.5A )

Battery

Built-in 3.7V Lithium polymer battery ,.3000mAh

Rechargeable

After charging3~4 hours, normal working time 8 hours

Parameter

Operation setting

Capacitive touch screen, OSD menu, select your desired language: English, Chinese, Korean, Russian, Italian or Polish, etc

Auto off

1-30 (mins)

General

Working Temperature

-10℃---+50℃

Working Humidity

30%-90%

Dimension/Weight

194mm x 112mm x 48mm / 540g

Range

Accuracy

Resolution

660mV (Manual range)

±（0.3%+4）

0.1mV

Note: * signs means Optional function

4.2 Multi-meter specifications

Counts:-6600～+6600 Conversion rate: 3times/s Current modes for clamp meter with ZERO function Isolation: the Multi-meter connector must be isolated with the other connector.

DC voltage

6.600V

1mV

66.00V

10mV

660.0V

100mV

Range

Accuracy

Resolution

660.0mV (Manual range)

±（1.5%+6）

0.1mV

6.600V

±（0.8%+6）

1mV

66.00V

10mV

660.0V

100mV

Range

Accuracy

Resolution

6.600mA

±（0.5%+3）

1uA

66.00mA

10uA

660.0mA

100uA

10.00A

±（1%+5）

10mA

Range

Accuracy

Resolution

6.600mA

±（0.5%+3）

1uA

66.00mA

10uA

660.0mA

100uA

10.00A

±（1%+5）

10mA

AC voltage

DC current

AC current

Resistance

Range

Accuracy

Resolution

660.0Ω

±（0.8%+5）

0.1Ω

6.600KΩ

±（0.8%+2）

1Ω

66.00KΩ

10Ω

660.0KΩ

100Ω

6.600MΩ

1KΩ

66MΩ

±（1.2%+5）

10KΩ

Range

Resolution

Function

660.0Ω

0.1Ω

The measurement value less 30Ω±3Ω,the tester will

sound

Range

Resolution

Function

2.0V 1mV

Schottky diode:0.15~0.25V rectifier diode:0.6~1.0V triode PN junction:0.5~0.8V

Range

Accuracy

Resolution

6.600nF

±（0.5%+20）

1pF

66.00nF

±（3.5%+8）

10pF

660.0nF

100pF

6.600μF

1nF

66.00μF

10nF

660.0μF

±（5%+8）

100nF

Continuity

Diode

Capacitance

6.600mF

1μF

66.00mF

10μF

Measure Range(dBm)

-70～+10dBm

Wavelength(nm)

850nm,1300nm,1310nm,1490nm,1550nm,1625nm

Detector

InGaAs

Uncertainly

＜±3%dB( -10dBm,22℃)

＜±5%dB(full range,22℃)

Display Resolution

Linear:0.1% ; Nonlinear:0.01dBm

Operating Temperature(℃)

-10～+50

Storage Temperature (℃)

-20～+70

Connector type

FC/PC

Laser type

Wavelength Calibration

650nm

Output power

5mW（Optional 10mW,20mW）

Modulation mode

CW/1Hz/2Hz

Measurement Range

5KM（Optional 10-20KM）

4.3 Optical power meter specifications

4.4 Visual fault locator specifications

Connector

FC/PC exchangeable

Working Temperature

－10℃～+50℃

Operating Temperature

-20℃～+70℃

The data above is only for reference and any change of them will not be informed in advance. For more detailed

technical inquiries, please feel free to call the Technical Department of our company.

Avycon AIVO-35T User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual