Avocent LCD15, LCD17 Quick Installation Manual
The following instructions will help you install your 15/17 LCD
Tray. Should you require further assistance, please contact
Avocent Technical Support.
The 1U 15/17 LCD Tray supports USB and PS/2 trackball and
keyboard, and includes a mounting kit consisting of two outer
rails with front and rear brackets attached, one rail-alignment
spacer, one IEC connector power cable and related connector
hardware.
1
Preparing the rack for installation
Review the documentation that comes with your rack
for safety and cabling information. When installing your
system in a rack, consider the following:
Ensure that the room air temperature is below 95°F and
do not block any air vents (usually 6” of air space provides
proper airflow). Starting with the heaviest, install devices
from the bottom of the rack. Never extend more than one
device out of the rack at the same time. Connect power
cords to properly wired and grounded electrical outlets,
Do not overload the power outlet when installing multiple
devices in the rack.
2
Installing the 15/17 LCD Tray
Select a 1U location in the rack and install the appropiate
cage or clip nuts. Next, loosen the two rail-adjustment
screws on each of the outer slide rails and extend the rails
to their maximum length.
Adjust the outer slide-rail brackets to fit the depth of the
rack cabinet, and then use four screws to attach the front
of the slide-rail brackets to the rack cabinet. Make sure
that the slide-rail brackets extend outside of the rackcabinet mounting flanges.
NOTE:
Do not install screws in the slide-rail bracket
middle holes. These holes are for the thumbscrews on
the front of the
LCD Tray.
Loosely attach the back of the slide-rail brackets to the
rack cabinet, using four screws. Ensure that the slide-rail
brackets extend outside of the rack-cabinet mounting
flanges. Tighten the two rail-adjustment screws on each of
the outer rails.
Next, loosen the front four slide-rail bracket screws
and insert the rail-alignment spacer between the finger
brackets and over the slide-rails. The rail-alignment spacer
must wrap around the rails to align and distance them
correctly. Brackets must fit snugly against the ends of
the spacer to establish proper gap. Tighten the front four
screws and remove the spacer.
Now, extend the inner part of the outer rails and slide
the ball-bearing assemblies forward to the front of the
outer rails making sure it is engaged with the plastic
guide. Carefully slide the LCD Tray into the ball-bearing
assemblies in the rails.
3
Sliding the 15/17 LCD Tray into the rack
Loosen the Velcro® straps on the cable retractor to allow
free and smooth movement of the cable retractor arm.
Press the release latches, and then push the LCD Tray
completely into the rack. There will be resistance initially
as the ball-bearing assemblies align between the inner
and outer rails. Pull the LCD Tray out halfway, and then
push it back in to seat the LCD Tray in the rails. Do this a
few times until the LCD Tray moves smoothly in the rails.
Push the LCD Tray into the rack, and then tighten the four
rear slide-rail bracket screws.
Remove the black rail-adjustment screw that is closest to
the rear of the rack from the outer slide-rail bracket and
discard. Attach the cable-management arm (CMA) to the
outer slide-rail bracket, using the thumbscrew attached to
the CMA.
4
Connecting the 15/17 LCD Tray
Connect the video, keyboard, and mouse connectors to
either a server or a console switch in the rack cabinet.
Connect the power cord to a properly grounded electrical
outlet or power distribution unit (PDU).
Fully extend the LCD Tray from the front of the rack
cabinet, and then route the cables within the rack cabinet,
securing them with cable straps along the way. Do not
coil the cables.
To minimize the electrical interference from the video
cable, arrange the cable in figure-eight loops. Secure the
cable in the middle with a cable strap.
NOTE:
If necessary, the monitor and keyboard can
be secured inside the rack cabinet using the two
thumbscrews on the front of the LCD Tray.
(Continued on reverse side)
QUICK INSTALLATION GUIDE 15/17 LCD Tray
Technical support and software or firmware updates: www.avocent.com
Product manuals: www.avocent.com/manuals
Avocent and the Avocent logo are registered trademarks of Avocent Corporation in the U.S. and other countries. All other marks are the property of their respective owners. ©2008 Avocent Corporation.
590-896-501B
Rail-adjustment
screws
Lengthen/Shorten to Fit
NOTE: Inner slide rails
have been removed for
illustration purposes
Spacer
Inner part of
outer rails
extended
Latch
LCD Tray
CMA
thumbscrew
Remove
existing screw
CMA
Keyboard Controls
The 15/17 LCD Tray keyboard with integrated pointing
device is designed for use with any USB, PS/2 or
compatible computer. Both the pointing device and
keyboard use the host computer’s operating system
generic software drivers and therefore do not require
custom software drivers to be installed on the host
computer prior to use.
Numeric Keypad
The number keys and letter keys share space on the
keyboard. To activate the numeric keypad, press the
Num Lock key to turn on the Num LED. With the Num
LED activated, simultaneously press the Fn key and the
desired number key. For example, press Fn + O to type
the number 6.
Both the Fn LED and the Num LED must be lit in order for
the numeric keypad to operate.
For longer numeric entries, press Fn + F11 to initiate a
continuously active numeric keypad.
LCD Controls Description
Turns the 15/17 LCD Tray
on or off. A green LED indicates normal operation.
Auto Auto-synchronizes and
scales down display to
factory presets.
Exit Exits the OSD or returns
to previous menu.
Right arrow Selects the function to be
adjusted and increases
values of settings.
Left arrow Decreases values of
settings.
Controls the brightness of
backlight lamps without
using the OSD menu.
Menu Displays the OSD menu
and moves selector on the
OSD menu.
LCD TR AY SAFETY AND
EMC NOTIFICATIONS
USA
WARNING: Changes or modifications to this unit not
expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to
comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference
when the equipment is operated in a commercial environ-
ment. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful
interference in which case the user will be required to
correct the interference at his own expense.
Japanese Approval
Safety and EMC Approvals and Markings
BSMI, CCC, CE, C-TICK, FCC, GOST, TUV/INNOVA,
KCC, UL, ULC, VCCI
Safety Precautions
Certifications for this product are obtained under one or
more of the following designations: CMN (Certification
Model Number), MPN (Manufacturer’s Part Number) or
Sales Level Model designation. The designation that is
referenced in the certifications reports and/or certificates
are printed on the label applied to this product.
DANGEROUS VOLTAGE
This symbol is intended to alert the user to the
presence of uninsulated dangerous voltage
within the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons. Never remove a cover on a power supply or any
part that has this label attached.
NOTE: The AC inlet is the main power disconnect.
INSTRUCTIONS
This symbol is intended to alert the user to the
presence of important operating and maintenance
(servicing) instructions.
WARNING: To reduce the risk of electric shock or damage
to your equipment:
– Do not connect or disconnect any cables or perform
installation, maintenance, or reconfiguration of this
product during an electrical storm.
– Connect all power cords to a properly wired and
grounded electrical outlet.
– Connect any equipment that will be attached to this
product to properly wired outlets.
– When possible, only use one hand to connect or
disconnect signal cables.
– Never turn on any equipment when there is evidence
of fire, water, or structural damage.
– Disconnect the attached power cords, networks,
telecommunications systems and modems before you
open the device covers, unless instructed otherwise in
the installation and configuration procedures.
Rack and Wall Mount Safety Considerations
• ElevatedAmbientTemperature:Ifinstalledinaclosed
rack assembly, the operation temperature of the
rack environment may be greater than room ambient.
Use care not to exceed the rated maximum ambient
temperature of the appliance.
• ReducedAirFlow:Installationoftheequipmentin
a rack should be such that the amount of airflow
required for safe operation of the equipment is not
compromised.
• MechanicalLoading:Mountingoftheequipmentinthe
rack should be such that a hazardous condition is not
achieved due to uneven mechanical loading.
• CircuitOverloading:Considerationshouldbegiven
to the connection of the equipment to the supply
circuit and the effect that overloading of circuits
might have on overcurrent protection and supply
wiring. Consider equipment nameplate ratings for
maximum current.
• ReliableEarthing:Reliableearthingofrackmounted
equipment should be maintained. Pay particular
attention to supply connections other than direct
connections to the branch circuit (for example, use of
power strips).
QUICK INSTALLATION GUIDE 15/17 LCD Tray
Technical support and software or firmware updates: www.avocent.com
Product manuals: www.avocent.com/manuals
Avocent and the Avocent logo are registered trademarks of Avocent Corporation or its affiliates in the U.S. and other countries. All other marks are the property of their respective owners. ©2008 Avocent Corporation.
590-896-501B
Loading...