Avital PHEONIX 2 Installation Manual

Phownix2 Rev. A - Installation Manual - Front Cover

Table of Contents

Important Information ........................... 2

Required Installation Tools ........................ 2

Recommended Procedures .......................2

Wiring Diagram ............................. 3

20 Pin Connector............................4

Installation Procedures...........................5

Control Unit............................... 5

Antenna................................. 5

Wireloom ................................5

Zone2™ Impact Sensor..........................5

Valet Switch...............................6

LED Indicator..............................6

Ignition Input ..............................6

Channel 2 Accessory (-) Output..................... 6

Channel 4 Accessory (-) Output..................... 6

Channel 6 Accessory (-) Output..................... 7

Parking Lights..............................7

Interior Light Trigger/Illumination .................... 7

Starter Disable.............................. 7

Door Lock/Unlock............................8

Door Lock Diagrams ..........................9

Hood/Trunk Pin Switch.........................13

Siren ..................................13

Power and Ground Connections.................... 13

Programmable Features.......................... 14

Programming Table for Alarm Features ................. 15

Programming Table for Remote Controls ................ 16

Phoenix2 Rev. A - Installation Manual 0399

1

Important Information

Required Installation Tools

Voltmeter

Voltmeter Wire Strippers

Wire Strippers Electric Drill & Bits

Electric Drill & Bits Phillips Screw Driver

Phillips Screw Driver Convoluted Tubing *

Convoluted Tubing * Solder Gun *

Solder Gun * Wire Crimpers

Wire Crimpers Shrink Tube or Electrical Tape

Shrink Tube or Electrical Tape

* Optional

Recommended Procedures

1. Test all circuits with a voltmeter.

2. Make all wiring connections with the supplied solderless crimp

2. Make all wiring connections with the supplied solderless crimp connectors. DO NOT twist wires or use “scotch-lok” connectors.

connectors. DO NOT twist wires or use “scotch-lok” connectors.

3.

Route RED , RED/WHITE and BLACK wires from the control unit directly

Route RED , RED/WHITE and BLACK wires from the control unit directly to the battery.

to the battery.

4. Keep extensions as short as possible. Use same gauge wires for short

4. Keep extensions as short as possible. Use same gauge wires for short extensions and larger gauge wires for longer extensions.

extensions and larger gauge wires for longer extensions.

5. Before installing, discuss the placement of the LED indicator and valet

5. Before installing, discuss the placement of the LED indicator and valet switch with the vehicle owner.

switch with the vehicle owner.

6. Make all battery connections by removing the bolts from the cable

6. Make all battery connections by removing the bolts from the cable clamps. DO NOT disconnect the battery cables.

clamps. DO NOT disconnect the battery cables.

7. Turn off dome light(s) or remove dome light fuse to prevent battery drain.

8. Making secure connections is a very important part of your installation.

8. Making secure connections is a very important part of your installation. Solderless crimp connectors are supplied in your hardware accessory

Solderless crimp connectors are supplied in your hardware accessory package. This type of connection is sufficient for most of your installation.

package. This type of connection is sufficient for most of your installation. However, soldering of the starter disable wires is recommended whenever

However, soldering of the starter disable wires is recommended whenever possible. For a more secure installation, solder all of your connections and

possible. For a more secure installation, solder all of your connections and insulate with heat shrink tubing.

insulate with heat shrink tubing.

This device complies with Part 15 of the FCC rules. Any changes or modifications

This device complies with Part 15 of the FCC rules. Any changes or modifications made to the system without the express approval of Prime Security could void the

made to the system without the express approval of Prime Security could void the user’s authority to operate this equipment.

user’s authority to operate this equipment.

2

Phoenix2 Rev. A - Installation Manual 0399

Wiring Diagram

Phoenix2 Rev. A - Installation Manual 0399

3

20 Pin Connector

Pin Number Wire Color Description

1 2 VIOLET Siren (-) Output 3 DARK BLUE Channel 2 (-) Output (Trunk Release) 4 5 BLUE / YELLOW Channel 6 (-) Output 6 GRAY Armed (-) Output Prewired to Starter Disable Relay 7 8 PINK Ignition Output

9 LIGHT GREEN Second Stage Unlock (-) Output 10 11 12 RED / BLACK Parking Light Output 13 14 15 GREEN / BLACK Unlock Switch Side 16 17 18 BLUE / BLACK Lock Switch Side 19 20

RED

LIGHT BLUE

TAN

BLACK

RED / WHITE

WHITE

WHITE / BLACK

GREEN / WHITE

GREEN / RED

BLUE / WHITE

BLUE / RED

Hood / Trunk Switch (-) Input

Parking Light Polarity Input, (+) or (-) Input Select

Door Trigger Polarity Select Input

Unlock Polarity (+) or (-) Input Select

Lock Polarity (+) or (-) Input Select

Battery (+)

Channel 4 (-) Output

Battery (-)

Interior Light Input

Unlock Motor Side

Lock Motor Side

4

Phoenix2 Rev. A - Installation Manual 0399

Installation Procedures

Control Unit

1. Select a location under the dash that will allow you to use the tie wraps to

1. Select a location under the dash that will allow you to use the tie wraps to securely fasten the control unit.

securely fasten the control unit.

2. Mount the control unit as high as possible to ensure maximum range.

3. Do not mount the control unit near moving parts.

4. Avoid areas that are in the direct path of air blowing from the vents.

5. Route wires from this point, leaving slack for ease of service.

Antenna

1. Do not shorten or lengthen the antenna.

2. Route the antenna away from the control unit.

3. Keep the antenna as far away from metal and wire harnesses as possible

3. Keep the antenna as far away from metal and wire harnesses as possible to optimize range.

to optimize range.

Wireloom

1. Plug the wireloom securely into the control unit.

2. Route wires from the control unit directly to each connection point.

3.

Separate the RED, RED/WHITE, BLACK, VIOLET and TAN wires.

4. Sleeve the wires with vinyl tubing or electrical tape and route them

4. Sleeve the wires with vinyl tubing or electrical tape and route them through an existing rubber grommet into the engine compartment.

through an existing rubber grommet into the engine compartment.

5. If an existing grommet is not available, drill a hole and install a snap

5. If an existing grommet is not available, drill a hole and install a snap grommet.

grommet.

Zone2™ Impact Sensor

The sensor must be firmly mounted on a solid metal surface inside the vehicle.

The sensor must be firmly mounted on a solid metal surface inside the vehicle. We recommend tie wrapping the sensor to the steering column housing or

We recommend tie wrapping the sensor to the steering column housing or steering column support bracket. DO NOT mount the sensor near moving

steering column support bracket. DO NOT mount the sensor near moving parts or in the direct path of an air duct opening.

parts or in the direct path of an air duct opening.

1.

Plug the impact sensor BLUE 4-pin connector into the control unit BLUE

Plug the impact sensor BLUE 4-pin connector into the control unit BLUE 4-pin connector.

4-pin connector.

2. Route the impact sensor harness to the chosen mounting location.

3. Using the long tie wraps supplied, securely fasten the impact sensor

3. Using the long tie wraps supplied, securely fasten the impact sensor allowing access to the adjustment screws.

allowing access to the adjustment screws.

5

Phoenix2 Rev. A - Installation Manual 0399