Aviosys IP Power 9820 Lite User Manual
IP Power 9820 Lite
User Manual
Firmware Version: 2.0D
Date Released: NOV. 2015
- 1 -
Warning: Any changes made to this equipment without permission may cause damages to the device!
IMPORTANT NOTICE
1. IP Power 9820 Lite was designed for indoor use, we carry no responsibility for possible
damages caused by outdoor use, especially in the rain.
2. Please use the power adapter provided by the dealer, we carry no responsibility for the
possible damage from using power adapters not provided by us .
4. Do not shake the IP Power 9820 Lite in any fashion
5. Please contact the dealer If IP Power 9820 Lite is not working properly.
Copyright © 2014 All rights reserved. No part of this publication may be reproduced, stored in a
retrieval system, or transmitted in any form or by any means, electronic, mechanical,
photocopying, recording or otherwise, without the prior written consent of us.
All trademarks and products mentioned in this document are the properties of us.
- 2 -
Table of Content
WELCOME ........................................................................................................... 4
Introduction .................................................................................................................................................. 4
PRODUCT OVERVIEW ........................................................................................ 5
Features ......................................................................................................................................................... 5
Specification .................................................................................................................................................. 6
Minimum System Requirements ................................................................................................................. 6
Package Contents ......................................................................................................................................... 6
INTERFACE DESCRIPTION ................................................................................ 7
Front View..................................................................................................................................................... 7
Rear View :.................................................................................................................................................... 8
From Left side to Right side ..................................................................................................................... 8
SETTING UP USER DEVICE ............................................................................... 9
Before we Start ............................................................................................................................................. 9
Hardware Connection .................................................................................................................................. 9
Software Installation ...................................................................................................................................10
Installing Software ....................................................................................................................................10
Connection by WiFi- WPS ( WiFi Protection Service ) ...........................................................................11
Connection first by LAN –Network cable then setup for WiFi connection ..............................................13
Internet Setup ............................................................................................................................................18
Using IP Server .........................................................................................................................................19
WEB INTERFACE .............................................................................................. 20
Connect to user Device ...............................................................................................................................20
Device name .............................................................................................................................................22
Display or Hide the left setting section : ...................................................................................................22
Information : .............................................................................................................................................23
Power Control : ........................................................................................................................................23
Network : ..................................................................................................................................................34
Application Settings..................................................................................................................................44
System Setting ..........................................................................................................................................55
CGI HTTP Commands ...............................................................................................................................64
Telnet Control ..............................................................................................................................................66
- 3 -
FAQ :
................................
is a new generation of the Power Distribution Unit
s able to
& fast to set up a device to user wireless home/office
With embedded web server and
User can control power easily
Smartphone
( iOS ) and Android
allows user to remote control power up to
With higher power current design ,
15 Amp / 220V
user can use public email like Gmail / Hotmail / Yahoo mail to get the
email as the ON/OFF status change . User can al
search the other IP Device in webpage directly
ol through web bro
control the outlet power turn ON / OF
arch device in LAN / WAN Android phone / touch panel .
9820 Lite
home automation .
also can connect
has
directly search the other IP Device in webpage directly
For system integrator, there are several popular d
development . The various applications of the
Power Management, Server Management, Internet Controllable Timer,
System Integration, Remote Power Control in Remote
User can also replace own langrage through the webpage of 9820 L
& Powerful ,
..................
& Remote Power
function for easy
ntrol in the network
grade security
through the web browser
via
current of IP Power
With HIGH INRUSH CURRENT
mail without doing port
search the other IP Device in webpage directly
or Android
which is more
9820 Lite
of different network to log in fast and easy.
TelNet , SNMP and
Welcome
Introduction
IP Power 9820 Lite
Control (RPC) system. It’
working on Internet.
Windows PC or on
Chrome , Safari
9820 Lite
network .
up to 20AMP / 110V or
protection ,
As support SSL & SNMP,
forwarding / port mapping and
Besides contr
user to
quick se
Not only control manually,
suitable for factory / office /
IP Power 9820 Lite
phone customer , 9820 Lite
Command ( SDK) for 2nd
User Friendly . Convenience
................................................................
(PDU)
connect to the LAN/ WiFi network plus WPS
network and co
HTTPS protection , 9820 Lite supports higher
and more safely
like Internet Explorer (IE) , Firefox , Google
system.
8 separate devices ON/OFF
the total maximum
(Power Inlet as C20 ).
so control by e-
.
wser, there is Android Apps name “IP Power “ f
F,
supports Auto Ping , Time Scheduler
USB Camera to view the area near
QR code
.
eveloping tolls like
9820 Lite
locations ………….. etc.
it e.
67
as
on
9820 Lite is
. For smart
Use can
HTTP
includes:
- 4 -
Product Overview
Features
1) 8 ports 1U 19” Rack mount remote Power Controller : Wireless & Wired control.
2) Web Server built-in design, directly control by web browser – PC & Smart phone :Internet
Explore (IE) , Firefox , Google Chrome, Safari - iPhone and Android browser of smart
phone. ( Windows , Android & iOS) .
3) Support APPLE iOS APP & Android Apps “IP Power “ – free of charge
- Controls the outlet power ON/OFF
- Quick search in LAN / WAN ( liek IPEDIT & IP Serice )
4) Support WiFi 802.11n-b/g ,plus WPS for easy WiFi setup .
( WPA-PSK, WPA2-PSK, AES,128-bit WEP,64-bit WEP,TKIP, WPA2,WPA )
5) Support HTTPS /SSL, TCP/IP , PPPOE, DHCP, DDNS, SNMP & SMTP & Telnet
6) Support HIGH Power usage inquire :
- Adopt high grade Component & Relay for better quality / performance / durability
- + Maximum current per outlet : 10 Amp
+ Maximum current total 8 outlets: 20Amp / 110V or
15 Amp / 220V ( Power Inlet as C20 )
+ Maximum watt for light control : 240 Watt ( such as T5 fluorescent light )
7) Live chart display the value of WH ( watt per hour) , Current Amp , Voltage & Temperature.
8) Support " HUGHER Inrush Current " for T5 fluorescent light for energy savings
9) Power Surge protection & FUSE embedded in
10) Support Log function & send to assign IP address (Syslog)
11) Save History as CSV file for application .
12) Support 1 pcs USB for USB Webcam ( W/ UPNP , M-JPG /YUV) to view the environment.
13) Convenience design for Smartphone :
- Webpage : easy to Control ON/OFF& get meter value
- Android APP “ IP
- QR Code : create QR code of the 9820 Lite IP address
14) Time Schedule - can pre-set a suitable time to turn power on / off automatically .
15) Support Auto Ping for auto control management.
16) Back Up function for quick setup for multiple devices like Time Schedule, Network Setting
17) E-mail control function & E-mail alarm :
- Receive Email with Current , Voltage & Temperature info. as device boot up.
- POP3 Control : Control each outlet ON/OFF through E-mail
Support public e-mail -- @gmail.com , @yahoo.com , @hotmail.com ..........etc.
18) Embedded IP Manager to search other IP device in local network in webpage directly.
19) Specific software developed by Aviosys and provided free of charge :
- SDK available : HTTP Command
- IP Power Center - for control multiple Aviosys IP devices in same software
- CNT software ( Cross Network Technology )- allows user eliminate set up work on any
Router without port forwarding , simply Plug & Play .
- Arrange own langrage display
20) Support “ Wake on LAN” & Shut down on LAN”
- 5 -
Specification
Power input : 100V - 240V ( C20 Inlet )
Maximum loading of each output: 10 amp
Maximum of Total loading : 20Amp / 110V or 15 Amp / 220V
Dimensions: 450 x 170 x 45 mm ( L x W x H )
Weight: 1.40g
Minimum System Requirements
PC with web browser & network capacity.
Web Browser : IE 9.0 or above , Firefox, Google Chrome , Safari
RJ45 LAN & Internet HUB & Switch
JAVA version 1.60 or above to check USB Webcam under web browser Internet Explorer -IE
Internet ( for remote access) or Ethernet Network ( Internal Network use) with some type of
Internet connection, (i.e. ADSL, Cable, Dial up or any other forms of Internet service)
Package Contents
1. 9820 Lite
Unit x 1
( The picture
is With
Antenna)
2.
Installation
CD
2. WiFi
Antenna
X 1 pcs
The power inlet SPE is C20 . Please double check the power cable compatible
3. Input
Power
Cable
(option)
for 10/15/20 amp current loading ( depends on user device power consumed ) .
Power cable outlook example : Europe Style
- 6 -
Interface Description
Front View
From Left side to right side
Wifi Connection :
Connect with the WiFi Antenna in package .
Network & USB :
WiFi - Signal light
MCU - light
Number 1 to 8 - Outlet status
Reset :
Network Connection :
For 10/100 Mbps network .
There are 2 network RJ45 connect :
NET1 - BLUE is for network connection
NET2 – Gray is for by pass as hub function only
Please connect NET1 to the Router/ Hub / IP Switch.
USB Connection for USB Camera.
There are 2 USB 2.0 connectors :
One is for USB Camera connection for USB Web
Camera with UPNP & video format as M-JPG / YUV.
Another one is for USB Flash Drive saving current
& temperature sensor data as CSV files
Please do not connect more than 1pc. USB Camera to
9820 Lite .
WiFi Signal light in flash Green . The Indicator shows
the WiFi signal transfer status. The light will be keep
flash as WiFi connected .
For internal developing purpose. Green light is always
ON
To indictor the power ON /OFF status of each outlet
Light in Green : power ON
Light in RED : power OFF
To There are two functions for this button.
* Enable WPS function by one short click
There is one long beep as enable WPS function. Please
refer page #16 for details.
* Set back to default setting by long press
- 7 -
Power Light
:
1 Power Switch:
Rear View :
To reset to original manufacture settings, hold down the
reset button with a sharpen pin for
5- 6 seconds then release. There are THREE beeps
response ( short –- mid long – short ) which means
reset successfully and 9820 Lite will be rebooted itself
( one beep after reboot ) and most information go back
to default setting .
Device power .
From Left side to Right side
Power Inlet :
Breaker Reset :
8 Outputs:
90~240 VAC & 50~60HZ
IEC320 C20. 20A / 250V AC
The Power switch turns on the input power.
This is Fuse protection to prevent electrical surges
from damaging the unit. The 9820 Lite comes with one
spare fuse in the unit.
9820 Lite -S : IEC 320 C13 . - 15Amp Fuse
9820 Lite -T : NEMA 5-15R . - 20Amp Fuse
There are 2 different outlets by different model :
9820 Lite -S : IEC 320 C13 .
The Maximum current of each outlet is 8Amp .
9820 Lite -T : NEMA 5-15R
The Maximum current of each outlet is 8Amp .
- 8 -
Setting up user device
Before we Start
*Before setting up the device make sure of the following:
1.) All the package contents are all included if anything is missing please contact the dealer
where the device was purchased from.
2.) Check the power input cable is working correctly.
3.) Check all cables to make sure there are no problems with it.
Hardware Connection
Please refer following procedure :
1.) Connect the Ethernet cable (RJ45) to the 9820 Lite to user local area network.
2.) Then connect the power cable into the power input port of the 9820 Lite .
3.) Connect the device that user would like to control to the output plug on the top of the 9820
Lite .
4.) Switching the power source to ON status , this switch is located at the rear of 9820 Lite .
5.) After power on for around 45 seconds , there is a short beep sound for 9820 Lite which
means the system reboot successfully
6. ) Go to page #16 for software installation guide – use IP Edit to log in the webpage of 9820
Lite .
Note: To change the network setting for WiFi connection ( if user Router without WPS function ) ,
please go to page # 19 to setup the WiFi connection manually .
- 9 -
Software Installation
The Media Link - IP Family CD comes with the device , it will have all the necessary software to
run and setup the device.
IP Power Software:
IP Edit (Required) & IP Power Center *( For multiple IP Power devices control )
Installing Software
1.) Place the Media Link-IP Family CD into the CD/DVD Rom drive.
(The CD should auto run but if it does not go to the CD/DVD Rom drive and select the
“autorun.html” file.)
2.) Click on the IP Power Section Bar
3.) Select the IP Power 9820 Lite
4.) All the available downloads for the 9820 Lite will be shown
5.) Download the required software – IPEdit.exe - by clicking on the download button.
Then user can select to connect 9820 Lite by LAN or by WAN / WAN- WPS
- 10 -
Connection by WiFi- WPS ( WiFi Protection Service )
IP Power 9820 Lite support WPS function which can assist user setup the WiFi connection of
user`s router and IP Power 9820 Lite automatically . Before using WPS function, please check
user WiFi router and see if there has WPS function first . There should have a button name
“WPS / QCC “ or a sign on the router for user to click easily.
Please refer following steps to setup WiFi –WPS connection
Step 1: Power on the 9820 Lite - only connect power in but do not connect the LAN cable ,
user will hear one short beep in 40 seconds means 9820 Lite boot successfully
Step 2: Press the “WPS button” of user WiFi Router. ( Please check the WPS function on own
router ) .
Step 3 : Just one short press the “ Reset button” of 9820 Lite and then there is one long beep
which means the WPS function of 9820 Lite enable .
Step 4: After few seconds , there are 2 short beep Which means WPS connection
successfully ( If WPS connection fail , there is one long beep mean the connection fail.
Please go back to step 2 and try again )
WPS Quick procedure :
One short press “ reset “ button on 9820 Lite One Short beep 5-10 seconds
short 2 beeps WPS connection successful
- 11 -
Step 5: There is one short beep in 45 seconds which means 9820 Lite boot up successfully .
Step 6 : Execute IPEDIT.exe . The device name with (w) mean the WiFi IP address of this
device . There is WiFi IP address of 9820 Lite shown in IPEDIT.exe as following :
If can not see the IP in the area of Local Devices of IPEDIT.exe. Please disable the
Firewall and Anti Virus software temporally .
Step 7 : Double click the IP address and user PC will execute web browser like IE ,Firefox or
Google Chrome and there is wizard pop up to enquire the Username and Password .
Username : admin Password : 12345678
Step 8 : For the WiFi connection by WPS way , user can check here :
Network WiFi Info Profile list
To make this WiFi IP Address can be found on Internet, please arrange 2 settings as log in the
9820 Lite webpage:
1st : Please go to “ Network Setting Default gateway Setting “ and change as WiFi for the
Default gateway Setting .
2nd : Please do the port mapping / port forwarding in your router ( Need to check the router
manual ).
- 12 -
Connection first by LAN –Network cable then setup for WiFi connection
Without WPS , user can use LAN network cable to connect 9820 Lite first .
Please refer following steps to setup LAN connection
Step 1: Connect the LAN cable to 9820 Lite .The LAN cable should be connected to a Router /
HUB + Router.
Step: 2 : Connect power cable to 9820 Lite and Power on the 9820 Lite .There is one short
beep in 45 seconds after 9820 Lite power up .The short beep means 9820 Lite boot up
successfully
Step 3 : After hear the one short beep , please execute IPEDIT.exe . There is IP address of
9820 Lite showed in the right side of IPEDIT.exe following :
If can not see the IP in the area of Local Devices of IPEDIT.exe. Please disable the
Firewall and Anti Virus software temporally .
Step 4 : Double click the IP address and user PC will execute web browser like IE ,Firefox or
Google Chrome and there is wizard pop up which inquire username and password .
Username : admin
Password : 12345678
- 13 -
LAN connect by IP Search software “ IPEDIT “
IP Edit is a search tool designed to search, configure, or access the IP Power 9820 Lite from a
local networked computer.
IP Power 9820 Lite Default Login / Password
Default IP: 192.168.1.168 (When no DHCP is apparently)
Default Login: admin
Default Password: 12345678
1.) In the local devices section user will see user device show up if connected correctly.
If can not see the IP in the area of Local Devices of IPEDIT.exe. Please disable the
Firewall and Anti Virus software temporally .
2.) Select the 9820 Lite device and the device information will pop up on the right.
3.) Check to see that the gateway IP and the IP Address (9820 Lite ) match user current
network.
If not, type in the correct information, then hit the submit button to save changes.
- 14 -
For example:
If user have the following information regarding the 9820 Lite and user network
User PC Network :
Computer IP Address: 192.168.1.122
Gateway: 192.168.1.1
Sub Net mask: 255.255.255.0
Port: 80
User 9820 Lite in IPEDIT :
9820 Lite IP Address: 192.168.100.34
Gateway: 192.168.100.1
Sub Net mask: 255.255.0.0
Port: 80
Since the IP Address of the 9820 Lite is : 192.168.100.34
User will need to make sure that the first 3 segments of user 9820 Lite IP Address
must match the first 3 segments of user gateway IP.
First 3 Segment of Gateway Address: 192.168.1.X
So user new IP Address for the 9820 Lite should be: 192.168.1.XXX
New Network Information
9820 Lite IP Address: 192.168.1.26
Gateway Address: 192.168.1.1
Local Computer IP Address: 192.168.1.122
Sub Net mask: 255.255.255.0
Port: 80
4.) Press the rescan button to see if changes have been made.
5.) Double click on the device in the local device section and an IE web browser
with the device login will pop up.
6.) Type in the default Login and IP Address to enter the device.
Default Login : admin
Default : 12345678
Notice :
* User can click " REF " in IEPDIT to auto search proper IP setting for 9820 Lite .
It will take few minutes to show the suggest wizard.
- 15 -
Please click APPLY as seeing the suggest wizard , click " yes " to ignore the remind
message of IP being used and then type the username and password to change the IP setting.
Username : admin
Password : 12345678
Notice :
# Segment : The first 9 digits of the IP Address .
EX: The IP of user PC is 192.168.100.122. If the “ Local IP Address “ at WiFi Info is 192.168.100.
x ( X can the value of 1~252 ) , user PC can get into the webpage of 9820 Lite .
# Please press “Rescan “ to search the router near by again if can not see user router in the list.
WiFi Connection after log in webpage by LAN :
After log in 9820 Lite , to connect by WiFi , please go to Network WiFi Survey to add the
WiFi router in to 9820 Lite WiFi profile .
1) As go to WiFi Survey page, there is a list for the available WiFi router near 9820 Lite .
Please select the one plan to use and click “ Add Profile “
- 16 -
9820 Lite will auto get the most information of user router and user just need to type the
password to connect with the WiFi router then click “ Apply “
Then user can get the router information in “ Profile list “ section as following pictures
Select the router and press “Activate “
- 17 -
As connection successful , the page will turn to “WiFi Information “ and show the information .
Now user can see the new WiFi IP address which can be found by software IPEDIT.
Then user can remove the LAN cable and re-log in the 9820 Lite by IPEDIT re-search of above
WiFi IP address.
Internet Setup
There are two ways to control the IP Power 9820 Lite over Internet :
If need full control through webpage on Internet , please setup Port Mapping / Port
Forwarding in user router. Please check user Router owner’s manual .
If just want to control each port ON or OFF in IP Power 9820 Lite , user can install our own
software “ IP Power Center “ and enable IP Server function as following . Please refer to the
“IP Power Center “ manual in attached CD .
- 18 -
Using IP Server
IP Server is a function which allows user to search for the device easily without having to
remember long complicated IP address. Instead, if user know the device’s name of user IP
Power device and user can easily find IP Address with IP Service. To log in the webpage of
9820 Lite on Internet , user still need to do the “Port forwarding “ in own router.
Before using “IP Server “ , please change the device name of user 9820 Lite to avoid
similar name in host server.
1.) Open IP Edit and select the server that user 9820 Lite is designated to.
2.) Hit the Green Connect button on the top of IP Edit.
3.) Then type in the 9820 Lite Name that user have selected for the device and press the
Search button.
4.) Find user device and double click on the screen and a IE window will pop up connecting to
user device. *User device must be Port Forwarded for the login screen to appear.
- 19 -
EX: The 9820 Lite device name as Cathy , and user can search the device easily after log in the
webpage and change the default name from “ IP_POWER ” to Cathy
5.) After user have connected to user device, type in the Login and Password for user device
Web Interface
Connect to user Device
Once the 9820 Lite has been setup correctly, log into the device.
First Option
1.) Go to IP Edit find the device that is being used
2.) Double click on the device linked and an IE window will appear with the loading screen
Second Option
1.) Open Internet Explorer type in the IP Address of the device followed by the : sign.
For example: http:192.168.122.188:9258
192.168.122.188 – IP Address
2.) Once user have typed in the IP address of the 9820 Lite and it is ready to use.
The default username and password for the 9820 Lite
Username : admin Password: 12345678
- 20 -
The Control Console
The left Menu of the Web Interface control the functionality and setup of the IP Power 9820 Lite .
The IP Power 9820 Lite Console consists of seven main sections which will be explained in
details below.
Device name & to Hide or Display the setting column at left ( for smart phone control )
Time Information
Power Control : Control , Schedule, Ping, Timeline & History
Network : Setting , WiFi Info , WiFi Survey & WPS
Application : Email , DDNS, SNMP, IP Server & Web Camera & USB Storage
System : Management, Information, SysLog & Firmware
Logout
Connection Period
- 21 -
Loading...