Aviosys IP Power 9258 DS User Manual

IP Power 9258 DS

User Manual

Firmware Version: 1.0

Date Released: 01/20/2009

- 1 -

Warning: Any changes made to this equipment without permission may cause damages to the

device!

IMPORTANT NOTICE

1. IP Power 9258 DS was designed for indoor use, we carry no responsibility for possible
damages caused by outdoor use, especially in the rain.

2. Please use the power adapter provided by the dealer, we carry no responsibility for the
possible damage from using power adapters not .

4. Do not shake the IP Power 9258 DS in any fashion

5. Please contact the dealer If IP Power 9258 DS is not working properly.

Copyright © 2009 All rights reserved. No part of this publication may be reproduced,
stored in a retrieval system, or transmitted in any form or by any means, electronic,
mechanical, photocopying, recording or otherwise, without the prior written consent of us.
All trademarks and products mentioned in this document are the properties of us.

- 2 -

Table of Content

1.) WELCOME......................................................................................................5

Introduction.................................................................................................................................................. 5

Minimum System Requirements................................................................................................................. 5

2.) PRODUCT OVERVIEW...................................................................................6

Features......................................................................................................................................................... 6

Specification.................................................................................................................................................. 6

Package Contents ......................................................................................................................................... 7

3.) INTERFACE DESCRIPTION...........................................................................8

Front View..................................................................................................................................................... 8

Rear View...................................................................................................................................................... 9

Rear View.................................................................................................................................................. 9

4.) QUICK START GUIDE..................................................................................10

Quick Hardware Setup.............................................................................................................................. 10

Quick Device Setup .................................................................................................................................... 10

5.) HARDWARE SETUP ....................................................................................11

6.) SOFTWARE SETUP.....................................................................................12

Installing IP Power Software.....................................................................................................................12

Using IP Edit............................................................................................................................................... 13

IP Service .................................................................................................................................................... 17

7.) HARDWARE INTERFACE............................................................................18

Hardware Reset.......................................................................................................................................... 18

Serial Port Control..................................................................................................................................... 18

How to Replace Fuse.................................................................................................................................. 18

- 3 -

8.) WEB INTERFACE.........................................................................................19

Connection to your Device......................................................................................................................... 19

The Control Console................................................................................................................................... 19

Power Setup................................................................................................................................................ 20

Power Controls........................................................................................................................................ 20

System Configuration................................................................................................................................. 21

System Setup ........................................................................................................................................... 21

DDNS...................................................................................................................................................... 23

E-mail...................................................................................................................................................... 24

Schedule Ports 1-4 & Ports 5-8................................................................................................................ 25

IP Service................................................................................................................................................. 26

Ping.......................................................................................................................................................... 27

Network Wakeup..................................................................................................................................... 29

Change Password..................................................................................................................................... 29

Firmware Update..................................................................................................................................... 29

Time Change............................................................................................................................................ 30

9.) CONTROLLING THE DEVICE......................................................................31

CGI HTTP Commands.............................................................................................................................. 31

Set Name Command................................................................................................................................31

Get Name Command............................................................................................................................... 31

Get Firmware Version Command............................................................................................................ 31

Get Time Command ................................................................................................................................32

Set Time Command................................................................................................................................. 32

Set Device Gateway Command............................................................................................................... 32

Set Device DNS Command..................................................................................................................... 33

Turn DHCP ON/OFF...............................................................................................................................33

View Log Command................................................................................................................................33

Serial Com (RS-232) Control..................................................................................................................... 34

Com1 ....................................................................................................................................................... 34

10.) XML FUNCTIONALITY ...............................................................................36

11.) FREQUENTLY ASKED QUESTIONS (F.A.Q)............................................37

- 4 -

1.) Welcome

Introduction

The IP Power 9258 DS is a state of the art Power Distribution Unit (PDU) & Remote Power
Control (RPC) system. The 9258 DS can be used for various applications including: Power

Management, Server Management, Internet Controllable Timer, System Integration and
much more.

This device allows you to control up to 8 separate devices via the internet. By using a web
browser, you can remotely control the power of the 9258 DS from virtually anywhere.

What makes this device different from other PDU’s is that it has a dual switch design.
Unlike other PDU or RPC units the 9258 DS is completely safe. The dual switch design cuts off

the power and will eliminate any most electrical threats that other systems may have.

Minimum System Requirements

CPU Minimum Requirements
CPU Processor: The same as or above a Intel Pentium III or AMD Athalon
Operating Systems: WINDOWS Operating Systems (IE5.0+SPI) & LINUX
Memory Requirements 64MB or More
Supports Direct Draw Graphics Card
RJ45 LAN & Internet HUB & Switch
Internet (For remote access) or Ethernet Network (Internal Network use) with some type of
Internet connection, (i.e. ADSL, Cable, Dial up or any other forms of Internet service)

- 5 -

2.) Product Overview

Features

1. Dual Switch Design for extra safety and protection

2. HUB function four 4 RJ45 connections

3. Auto-ping (Watch dog) Device Auto Restart / Reboot.

4. Supports: RJ45(HUB), TCP/IP, Http API, Web Server, SMTP Server, DDNS, Log file,
CNT, XML

5. 8 Power control output

6. 2 Main power inputs.

7. 1 RS232 port for System Integration.

8. Design Pressure System: Prevent interference with power noise design. (Second stage
isolation)

9. Scheduler System for date sensitive control

10. Http commands through Internet

11. Log Capability

12. CNT Technology: No Port Forwarding Needed in Router – Just Plug & Play

13. IP Service: Easily Find your device on the internet without having to remember
complicated IP’s

14. Light Aluminum Design

Specification

1. Input Power Voltage: 90-240 VAC

2. Input Frequency: 50/60 Hz full range

3. Dimension: 440x235x40 mm 1.8kg

4. Reliability testing Certification MBTF 200,000 hrs +

5. Operating temperature range: 0 - 50 degrees Celsius.

- 6 -

1.) 9258 DS Unit x 1

Package Contents

2.) 9258 DS Installation CD

3.) Extra Fuse x 1: Located in the
power input of the 9258 Pro

Refer to installing fuse section

4.) RJ45 Cable x 1 (Optional)

5.) Input Power Cable x 2
(Optional)

- 7 -

3.) Interface Description

Front View

Front View

4 Port Ethernet Hub:

Connect up to 4 separate devices with the
built in hub.

1 Serial Ports:

Serial Port 1: Regular Speed

Reset Button:

To reset to original manufacture settings,
hold down the reset button with a pen or a
pin for 15 seconds until will hear a long
beep sound.

Power Status Indicator:

The Power Status indicator

- 8 -

Rear View

Rear View

Rear View

8 Output Power Ports:

Connect up to 8 separate devices that will be
controlled by the 9258 DS. Ports 1-4

2 Input Power Ports:
The input power sends power to the 2 sets o

9258.

2 Power Switch:

The 2 Power switch turns on the input power
Ports 1-4: Switch 1
Ports 5-8 Switch 2

Replaceable Fuse: The 9258 uses a
TYPE：U/C GFE 10A 250V (PF)

- 9 -

4.) Quick Start Guide

Quick Hardware Setup

*Before you plug in the device make sure you have the appropriate input plugs.
* For 220-250V, please use power cable that can support 10A current.

Max Output Current: (total of each four outlets) 10A, (each outlet) 6A.
* For 100-120V, please use power cable that can support 15A current.

Max Output Current: (total of each four outlets) 15A, (each outlet) 6A

1.) Make sure that all the package contents are included, if anything is missing
please contact the store.

2.) Plug the RJ45 (Ethernet Cable) from your router or modem to any of the 4 ports
on the 9258 DS.

3.) Plug in the Input Power Plugs into the device and then into the wall of your
device.

4.) Plug in the devices that you want to control in the output ports of the 9258 DS

Quick Device Setup

Using IPEdit

1.) Click on the REF button,
automatically detect the network settings and setup the device.

2.) Once settings have been detected hit the apply button to apply the new settings.

3.) Hit yes to confirm and Enter the login and password for the Device to Approve
changes

and wait a few seconds. IPEdit will

- 10 -

4.) Then hit the rescan button on IPEdit to confirm the changes have been made.

5.) Once you have found your device double click on the device and the internet
explorer will pop up and ask for your login information.

6.) Type in your password & login and the device is ready to use.

* Remember that to access your device from the outside network, you will need to port
forward the IP Address of your device.

5.) Hardware Setup

1.) Connect the IP Power 9258 DS to a HUB or Router with a RJ45 network
cable.

2.) Connect the HUB or Router to the internet (May through ADSL/XDSL
modem).

3.) Connect the power adapter to the IP Power 9258 DS.

4.) Connect the power adapters of under control electric equipment to

corresponding out port of IP Power 9258-Pro.
Turn on your computer and the power adapter of IP Power 9258-Pro
* For 220-250V, please use power cable that can support 10A current.

Max. output current: (total of each four outlets) 10A, (each outlet) 6A.
* For 100-120V, please use power cable that can support 15A current.

Max. Output current: (total of each four outlets) 15A, (each outlet) 6A

- 11 -

6.) Software Setup

The software for the device is located on the Media Link-IP Family CD that came with the device.
IP Power Pack is located on the main page of the CD. Please follow the directions carefully and
install the necessary files

The IP Power Necessary Software:

IP Edit
IP Power Center

IPEdit: IP Family Program used to search, access, modify basic configurations of IP Family
products.

Surf 16 Channel (DVR Software): 16 channel multi-windows DVR software (For 9060 , 9100,
9310 / 9360 series only)

IOTracker: Device to Device control with firewall bypass technology
(For 9212 Delux / 9211 / 9222 for V.1.12 and later)

Infinity Cam: 4 Channel DVR software, with play back
(For 9060SL V.1.15 and below, 9100 series only)

Amcap / Vidcap:

IOTracker – Only For 9212 Delux, 9222, 9211

Installing IP Power Software

1.) First place the Media Link-IP Family CD that came with your device into your CD/DVD
Rom drive. The CD should auto run but if it does not go to the CD/DVD Rom drive and
select the file “autorun.html”.

- 12 -