Aviosys 8810-S User Manual

USB Step Motor 8810-S

Manual

Date : July , 2013

Version :1.0

1

Index

Introduction ................................................................................................................... 3

Features ................................................................................................................ 3

Minimum System Inquire.................................................................................... 3

SPEC..................................................................................................................... 4

Package ................................................................................................................ 4

Interface ........................................................................................................................ 5

Installation .................................................................................................................... 6

Hardware .............................................................................................................. 6

Driver & Software ................................................................................................ 6

Installation Procedure ................................................................................. 6

Software Interface ............................................................................................... 8

Clockwise...................................................................................................... 8

Counter Clockwise ...................................................................................... 8

Set Speed ..................................................................................................... 8

Select type ................................................................................................. 8

Control ........................................................................................................... 9

Schedule ....................................................................................................... 9

SDK - USB CDC emulation mode .......................................................................... 11

USB CDC emulation mode . ............................................................................ 11

2

Introduction

No need any USB protocol knowledge to control Step Motor through PC easily .

If you wan to use PC to control Step Motor , with the USB Step Motor 8810-S , you can do it
simply plug and play. With no external case , just plug the USB port and use our software
to control the motor direction and steps. There has time scheduler function , you can
pre-set the time to auto control the motor .
Fit for Home / Office / Factory Automation application and school training purpose

Features

 Control through USB by PC software
 No need extra power source , use USB as power source and communication .
 Control one 5V Step Motor – Direction , Steps . Speed
 Scheduler - Timer control
 SDK ( USB CDC mode ) provided – command under hyper terminal/ putty directly .

as 2nd developing

Note : This product supports both 5V /12V Step Motor and PWM DC Motor

For DC Motor need to adjust 2 sets black jump
Please contact your reseller to buy the DC motor if need .

This board controls one kind of motor only at a time

Minimum System Inquire

 PC / Notebook with Windows OS like WIN 7 , VISTA or XP .
 USB 2.0 / 1.1.
 Microsoft .NET Framework Version 3.5 or above

3

SPEC.

ITE

M

SPECIFICATION

Rated Voltage

DC 5V

Motor Rated Load

0.25A/Phas

e

No. of Phases

Four（4）

Step Angl

e

7.5

∘

Excitation Method

2-2

Unipolar

Insulation Classificatio

n

Class

A

Operating Temperature

0〜+50℃

Operating Humidit

y

5〜90％R

H

Storage Temperature

-20℃〜+70

℃

Storage

Humidity

5〜95％R

H

8810-S x 1

USB Cable ( Male –Male)

For connect with PC

CD

With Driver , Manual and Software

Package

4

Interface

USB port

Connect with PC .

Motor Socket

Connect to Step Motor

5V Step Motor

Connect to Motor socket

Other Motor Application

12V Power In ( Left+ / Right - )

For other 12V Step Motor .
Need to adjust the JUMP position
Please refer the Hardware Installation .

5

Installation

Hardware

Please plug the Step Motor in package on the Motor Socket ( White )
Connect the 8810-S board to PC by USB cable. Windows will show that there is
Un-know hardware detected . Then install the driver and software from CD.

Notice：If use the option 12V Step Motor, user need to have the 12V power source

first . Please plug the power source to the green socket for 12V power in ( Left plus

+ & Right negative - ) , and plug the 12V step motor to white socket and adjust the jumper
as following :

Driver & Software

Installation Procedure

1. Please make sure that your PC had install .NET . or go to the link below to

download before install USB Step Motor 8810-S . :

http://www.microsoft.com/en-us/download/details.aspx?id=21

2. After install .NET, please insert the CD in your CD ROM and it will execute

6

AUTORUN. file or you can open by Windows . Please use web browser “ IE
“ to open the CD.

3. Then go to Manual  USB Series  USB Step Motor 8810-S to

Download the driver “ USB Net Power Driver” and the software “USB Step
Motor 8810-S.exe “ into your hard disk .

 Software : USB Step Motor 8810-S.exe
 8810 Driver: USB Net Power Driver .

4. Connect the 8810 power and the USB port of 8810 power to PC . PC will
pop up “ Detect New Hardware” , then select the 8810 driver and install .

5. After install the driver, you can get “Aviosys Port (COM X) in Ports (COM&
LPT) device manager as following .

Control Panel  System  Device manager  Ports(COM& LPT)  Aviosys Port (COM X)

4.) After confirm the 8810-S shown in Device Manager , please execute the software
“USB Step Motor 8810-S.exe “ and you will see as following :

7

Software Interface

Clockwise

Counter Clockwise

Set Speed

Here you can setup the Speedy , range as 200~ 10000, press SET button after
confirm .

Select type

Here you can setup the type and times :

 Infinite – keep turning
 Circle – turn one loop ( 360 degree = 48 steps )

8

 Single – move one step ( around 7.5 degree)
 Half - move half step

Times : Here user can setup the times range at 1 ~ 250.

Select “ Infinite “ then no need to setup the times .
Select “ Circle” + Times as “ 3 ” then the motor turn 3 loop
Select “ Single” + Times as” 6 “ then the motor turn 6 steps
Select “ Half “ + Times as “ 2 “ , then the motor turn 1 step.

Control

 Start
 Stop

Schedule

Set up the schedule to control motor. It is a helpful tool for auto control

Notice : Please turn off the Sleep function of PC and the 8810-S software need
to be keep executing as use scheduler function.

9

Here user can select date , time , direction and type :

 Date : Select the date in calendar .
 Time : Select the time .
 Direction : Left( Counter clockwise ) , Right ( Clockwise) , Stop .
 Type :

There are 4 types : Infinite – Keep turning . Circle – Loop , Single step , Half step

 Set times : Range as 1~250

For example : Select “ Left” + ” Single “ + “ 250” means
Turn Counter clockwise at 250 steps

Add – add new time schedule

Edit – edit time scheduler

1.) Press the item want to revise .

2.) Revised the date , time , direction , type and times.

3.) Please EDIT button’ s confirm .

Del – delete item

1.) Select the item want to delete

2.) Press DEL button .

Del All - delete all item in list

1.) Delete “ Del All” button to clear all list

2.) There is 2nd confirmation before delete all action

10

SDK - USB CDC emulation mode

For user to arrange its own development :

 Developing environment: :

- VB.NET 2008

- Microsoft NET. Framework Version 3.5

- Microsoft office access 2007

USB CDC emulation mode .

Please refer the setting as following :

1. First , make sure that the 8810-S is connect with your PC. Please go to

Control Panel  System  Device manager  Ports(COM& LPT)  Aviosys Port (COM X)

2. Then open Hyper terminal to connect with 8810-S.

Start  All programs Accessories  Communication  Hyper terminal
* There is no Hyper terminal program in WIN 7. Please use other serial software like Putty .
Select the COM port 8810-S use .

3. Setup “ Bits per second” as 19200 and “ Flow control” as NONE. Then press OK to log in .

After go into the command windows, please press “ enter “ key to get all the command .

11

[Command ]

1. Step Motor

ri --> keep turning clockwise
rl --> keep turning counter clockwise
rs --> turn clockwise one step
ls --> turn counter clockwise one step
rhs --> turn clockwise one step
lhs --> turn counter clockwise half step

2.stop --> stop turning

3.? Or key "Enter" --> show command list

4 . Fast command ─

~ - show 8811( step motor )。

! turn clockwise one step @ turn counter clockwise one step
#,+ turn clockwise half step $,- turn counter clockwise half step
% clockwise one turn ^ turn counter clockwise one turn
& keep turning clockwise * keep turning counter clockwise
( stop turning

Note : This product support both 5V /12V Step Motor and PWM DC Motor .

For DC Motor need to adjust 2 sets black jump .
Please contact your reseller to buy the DC motor if need .

This board controls one kind of motor only at a time.

Thank you for supporting our USB Motor 8810-S.
If any question , please e-mail to the distributor.

12