Page 1
Part No. P0943133 02
Business Communications
Manager 2.5
BIX Box Wiring Guide
Page 2
2
Copyright © 2001 No rtel Networks
All rights reserved. May, 2001.
The information in this document is subject to change without notice. The statements, configurations, technical data, and
recommendations in this document are believed to be accurate and reliable, but are presented without express or implied
warranty. Users must take full responsibility for their applications of any products specified in this document. The
information in this document is proprietary to Nortel Networks NA Inc.
Trademarks
NORTEL NETWORKS is a trademark of Nortel Networks.
Microsoft, MS, MS-DOS, Windows, and Windows NT are registered trademarks of Microsoft Corporation.
All other trademarks and registered trademarks are the property of their respective owners.
P0943133 02
Page 3
Contents
Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Regulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Related Publications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Chapter 1
BIX Wiring Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Using the BIX Tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Operating the Tool in the Cut Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Operating the Tool in the No-cut Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Installing the BIX Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Connecting the BIX Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Connecting to the Upper Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Connecting to the Lower Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Using the BIX Label Strips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
3
BIX Box Wiring Gui de
Page 4
4 Figures
Figures
Figure 1 QTBIX16A BIX tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Figure 2 How to set the BIX tool to the cut position . . . . . . . . . . . . . . . . . . . . . . . . . 9
Figure 3 Operating the BIX tool in cut position . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Figure 4 How to set the BIX tool to the no cut position. . . . . . . . . . . . . . . . . . . . . . 10
Figure 5 Operating the BIX tool in no cut position . . . . . . . . . . . . . . . . . . . . . . . . . 11
Figure 6 Example of a single channel installation . . . . . . . . . . . . . . . . . . . . . . . . . 11
Figure 7 Clearances required for installing BIX panels on the wall . . . . . . . . . . . . 12
Figure 8 Install the first mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Figure 9 Install the secon d mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Figure 10 Install the third mount and fourth (optional) mount . . . . . . . . . . . . . . . . . . 13
Figure 11 Install the distribution rings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Figure 12 Route incoming cables for connection on the BIX panel . . . . . . . . . . . . . 14
Figure 13 How to insert the upper and lower BIX connectors . . . . . . . . . . . . . . . . . 14
Figure 14 How to remove the BIX connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Figure 15 Fasten the cable to the upper connector . . . . . . . . . . . . . . . . . . . . . . . . . 15
Figure 16 Insert the BIX connector in the lower connector position . . . . . . . . . . . . . 16
Figure 17 Insert the wire pairs on the connector . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Figure 18 Terminate the cable and cut off the ends of the wires . . . . . . . . . . . . . . . 17
Figure 19 Insert the connector into the upper connector position . . . . . . . . . . . . . . 18
Figure 20 Fasten the lower connector cable wire . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Figure 21 Connecting to the upper connector pair in the No. 2 position . . . . . . . . . 19
Figure 22 Insert the wire pairs on the connector . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Figure 23 Terminate the cable and cut off the ends of the wires . . . . . . . . . . . . . . . 21
Figure 24 Insert the connector into the lower connector position . . . . . . . . . . . . . . . 22
Figure 25 Fasten the upper connector cable wire . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Figure 26 Insert the wire pairs on the connector . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Figure 27 BIX label strips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Figure 28 How to install the designation strips on the BIX mount . . . . . . . . . . . . . . 24
Figure 29 How to remove the designation strips from the BIX mount . . . . . . . . . . . 24
P0943133 02
Page 5
Tables
Table 1 Color code for 25 pair cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Tables 5
BIX Box Wiring Gui de
Page 6
6 Tables
P0943133 02
Page 7
Preface
This guide provides a pictoral overview about how to install a BIX box and wire it for the internal
and external (trunks) hard wire connections for the Business Communications Manager.
To use this guide, y ou must:
• be a Nortel Networks installer with Business Communications Manager certification
• know basic Nortel Networks terminology
Regulations
Refer to the Business Communications Manager 2.5 Installation and Maintenance Guide for the
regulatory infor ma ti on that affects the Busine ss Commun ications Manager hardware, software,
and configuration.
Related Publications
For more information about the Business Communications Manager and equipment installation,
refer to:
7
• Business Communications Mana g er 2.5 Ins talla tion an d Maintena nce Guide desc ribes ho w to
install the Business Communica tions Manager hardware, including the wiring for the media
bay modules.
• Business Communications Manager 2.5 Programming Operations Guide describ es how to
program the Business Communications Manager equipment.
BIX Box Wiring G u id e
Page 8
8 Preface
P0943133 02
Page 9
Chapter 1
BIX Wiring Overview
This guide provides a proce ss and descriptions about wiring and la belling the BIX
connectors.
Using the BIX Tool
This section describes the BIX tool and how to use it. Figure 1 shows a picture of the tool
Figure 1 QTBIX16A BIX tool
Operating the Tool in the Cut Position
Follow these steps to use the tool in the cut position.
1 Set the tool to the cut position. Refer to Figure 2.
2 Point the black blade towards the wire end to cut off.
Figure 2 How to set the BIX tool to the cut position
Installation and Maintenance Guide
Page 10
10 Chapter 1 BIX Wiring Overview
3 Insert the tool, on the connector, at a right angle and level. Refer to Figure 3
4 Push the tool to seat the wire in the co nnector.
5 Release forward pressure to cut the wire.
Figure 3 Operating the BIX tool in cut position
Operating the Tool in the No-cut Position
Follow these steps to use the Bix tool in the no-cut position:
1 Set the tool to the no-cut position. Refer to Figure 4.
Figure 4 How to set the BIX tool to the no cut position.
2 Keep the tool level and at right angles to the connector. Refer to Figure 5 on page 11.
3 Push the tool to seat the wire in the co nnector.
P0943133 02
Page 11
Figure 5 Operating the BIX tool in no cut position
Installing the BIX Mount
11
This section describes a single-channel installation. Figure 6 provides a diagram of this type of
configuration.
• Use the upper fi eld for the equipment side.
• Use the lower field for the house side or telephone/switching center side.
Figure 6 Example of a single channel installation
Installation and Mai nte nan ce Guide
Page 12
12 Chapter 1 BIX Wiring Overview
These steps describe how to mount a single-channe l BIX block.
1 Draw vertical and hor izontal refe re nce lines o n th e wall mounting surface. Ref er to Figure 7.
Figure 7 Clearances required for installing BI X pane ls on the wall
2 Install the screws to in stall the bottom mounts. R efer to Figure 8 to Figure 9.
Figure 8 Install the first mount
P0943133 02
Page 13
Chapter 1 BIX Wiring Overview 13
Figure 9 Install the seco nd mou nt
3 Install the screws to install the top m ou n ts. Refer to Figure 10.
Figure 10 Install the third mount and fourth (optional) mount
Third mount
Fourth mount
(optional)
4 Install the distribution rings above the mounts. Refer to Figure 11.
Figure 11 Install the distribution rings
Installation and Maintenance Guide
Page 14
14 Chapter 1 BIX Wiring Overview
Connecting the BIX Cables
Once the mounts are installed, set up the cable pathways. Ensure that the cable bending radius
complies with the note below.
Note: The bending radius is four times the cable diameter for four-pair cables. For
multi-pair cabl es, the bending radius is 10 times the cable diameter.
Figure 12 demonstrates how to route the cable into the mount at the cor rect bending radius.
Figure 12 Route incoming cables for connection on the BIX panel
Figure 13 and Figure 14 on page 15 demonstrate how to insert and remove the upper and lower
BIX connectors.
Figure 13 How to insert the upper and lower BIX connectors
P0943133 02
Page 15
Figure 14 How to remove the BIX connectors
Connecting to the Upper Connector
Follow these steps to connect the upper connector.
Chapter 1 BIX Wiring Overview 15
1 Fasten the cable to the upper connector. Refer to Figure 15.
Ensure the bending radius is maintained.
Figure 15 Fasten the cable to the upper connector
Installation and Maintenance Guide
Page 16
16 Chapter 1 BIX Wiring Overview
2 Insert the BIX connect or into the lower connect or position. Refer to Figure 16.
Figure 16 Insert the BIX connector in the lower connector position
3 Insert the wire pairs on the connector. Refer to Figure 17.
Table 1 on page 17 provides a summary of the wiring pattern for BIX connectors
Figure 17 Insert the wire pairs on the connector
TIP:
Insert the white/blue, blue/white wire pair into the first position on the left end of the
connector . Ins ert the violet /slate, sla te/violet wire pai r into the last position on the ri ght end
of the connector.
P0943133 02
Page 17
Chapter 1 BIX Wiring Overview 17
Table 1 Color code for 25 pair cable
Pair TIP (Body/Band) RING (Body/Band) Pair TIP (Body/Band) RING (Body/Band)
1 White/Blue Blue/White 14 Black/Brown Brown/Black
2 White/Orange Orange/White 15 Black/Slate Slate/Black
3 White/Green Green/White 16 Yellow/Blue Blue/Yellow
4 White/Brown Brown/White 17 Yellow/Orange Orange/Yellow
5 White/Slate Slate/White 18 Yellow/Green Green/Yellow
6 Red/Blue Blue/Red 19 Yellow/Brown Brown/Yellow
7 Red/Orange Orange/Red 20 Yellow/Slate Slate/Yellow
8 Red/Green Green/Red 21 Violet/Blue Blue/Violet
9 Red/Brown Brown/Red 22 Violet/Orange Orange/Violet
10 Red/Slate Slate/Red 23 Violet/Green Green/Violet
11 Black/Blue Blue/Black 24 Violet/Brown Brown/Violet
12 Black/Orange Orange/Black 25 Violet/Slate Slate/Violet
13 Black/Green Green/Black
4 Use the BIX tool to terminate the cable and cut off the ends of the wires. Refer to Figure 18.
Figure 18 Ter minate the cable and cut off the end s of the wires
Installation and Maintenance Guide
Page 18
18 Chapter 1 BIX Wiring Overview
5 Insert the connector into the up per connector position. Refer to Figure 19.
Figure 19 Insert the connector into the upper connector position
Connector
properly seated
TIP:
Insert the white/blue, blue/white wire pai r i nto the first position on the left end of the connector.
P0943133 02
Page 19
Connecting to the Lower Connector
Follow these steps to install the lower connector.
1 Fasten the lower connector cable wire. Refer to Figure 20.
Figure 20 Fasten the lower connector cable wire
Lower
connector
Chapter 1 BIX Wiring Overview 19
2 Connect the upper connector pair in the No. 2 position, as shown in Figure 21.
Figure 21 Connecting to the upper connector pair in the No. 2 position
Installation and Maintenance Guide
Page 20
20 Chapter 1 BIX Wiring Overview
3 Insert the wire pairs on the connector, as shown in Figure 22.
Figure 22 Insert the wire pairs on the connector
TIP:
Insert the white/blue, blue/white wire pair into the first position on the left end of the
connector . Ins ert the violet /slate, sla te/violet wire pai r into the last position on the ri ght end
of the connector.
P0943133 02
Page 21
Chapter 1 BIX Wiring Overview 21
4 Terminate the cable and cut off the ends of the wires, as shown in Figure 23.
Figure 23 Ter minate the cable and cut off the end s of the wires
Note: Using the wire retainer shown at the bottom of the figure is optional.
Installation and Maintenance Guide
Page 22
22 Chapter 1 BIX Wiring Overview
5 Insert the connector in the lower connector position, as shown in Figure 24.
Figure 24 Insert the connector into the lower connector position
P0943133 02
TIP:
Insert the white/blue, blue/white wire pair into the first position on the left end of the
connector.
Page 23
Chapter 1 BIX Wiring Overview 23
6 Fasten the upper connector cable wire, a s shown in Figure 25.
Figure 25 Fasten the upper connector cable wire
7 Insert the wire pairs on the connector, as shown in Figure 26.
Figure 26 Insert the wire pairs on the connector
See Table 1 on page 17 for a summary of the wiring pattern for BIX connectors
TIP:
Insert the whit e/blue, blue/white wire pair into the first posi tion on the
left end of the connector. Insert the violet/sl ate, slate/vi olet wire pair int o
the last pos ition on the right end of the connector.
Installation and Maintenance Guide
Page 24
24 Chapter 1 BIX Wiring Overview
Using the BIX Label Strips
Use the blank label strips to label wiring on BIX connectors. Refer to Figure 27.
Figure 27 BIX label str ips
Before you install the blank label strips, ref er to your work or der/install ation plan for the correct
position of blank labels.
Nortel Networks recommends the following color-coding guidelines:
• Use blue for telephone connections
• Use blue or green for riser cable
• Use green for incoming trunk connections
• Use silver for multiplying connectors
• Use yellow for other connections
Figure 28 shows the correct way to install the designation strips. Figure 29 shows the correct way
to remove the strips.
Figure 28 How to install the designation strips on the BIX mount
Figure 29 How to remove the designation strips from the BIX mount
P0943133 02
Loading...