Avaya 9500 User Manual

Page 1
IP Office Basic Edition
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide
- Issue 6b - (23 November 2011)
Page 2
© 2011 AVAYA All Rights Reserved.
Notices While reasonable efforts have been made to ensure that the information in this document is complete and accurate at the time of printing, Avaya assumes no liability for any errors. Avaya reserves the right to make changes and corrections to the information in this document without the obligation to notify any person or organization of such changes.
Documentation disclaimer Avaya shall not be responsible for any modifications, additions, or deletions to the original published version of this documentation unless such modifications, additions, or deletions were performed by Avaya.
End User agree to indemnify and hold harmless Avaya, Avaya's agents, servants and employees against all claims, lawsuits, demands and judgments arising out of, or in connection with, subsequent modifications, additions or deletions to this documentation, to the extent made by End User.
Link disclaimer Avaya is not responsible for the contents or reliability of any linked Web sites referenced within this site or documentation(s) provided by Avaya. Avaya is not responsible for the accuracy of any information, statement or content provided on these sites and does not necessarily endorse the products, services, or information described or offered within them. Avaya does not guarantee that these links will work all the time and has no control over the availability of the linked pages.
Warranty Avaya provides a limited warranty on this product. Refer to your sales agreement to establish the terms of the limited warranty. In addition, Avaya’s standard warranty language, as well as information regarding support for this product, while under warranty, is available to Avaya customers and other parties through the Avaya Support Web site: http://www.avaya.com/support. Please note that if you acquired the product from an authorized Avaya reseller outside of the United States and Canada, the warranty is provided to you by said Avaya reseller and not by Avaya.
Licenses THE SOFTWARE LICENSE TERMS AVAILABLE ON THE AVAYA WEBSITE, HTTP://SUPPORT.AVAYA.COM/LICENSEINFO/ ARE APPLICABLE TO ANYONE WHO DOWNLOADS, USES AND/OR INSTALLS AVAYA SOFTWARE, PURCHASED FROM AVAYA INC., ANY AVAYA AFFILIATE, OR AN AUTHORIZED AVAYA RESELLER (AS APPLICABLE) UNDER A COMMERCIAL AGREEMENT WITH AVAYA OR AN AUTHORIZED AVAYA RESELLER. UNLESS OTHERWISE AGREED TO BY AVAYA IN WRITING, AVAYA DOES NOT EXTEND THIS LICENSE IF THE SOFTWARE WAS OBTAINED FROM ANYONE OTHER THAN AVAYA, AN AVAYA AFFILIATE OR AN AVAYA AUTHORIZED RESELLER, AND AVAYA RESERVES THE RIGHT TO TAKE LEGAL ACTION AGAINST YOU AND ANYONE ELSE USING OR SELLING THE SOFTWARE WITHOUT A LICENSE. BY INSTALLING, DOWNLOADING OR USING THE SOFTWARE, OR AUTHORIZING OTHERS TO DO SO, YOU, ON BEHALF OF YOURSELF AND THE ENTITY FOR WHOM YOU ARE INSTALLING, DOWNLOADING OR USING THE SOFTWARE (HEREINAFTER REFERRED TO INTERCHANGEABLY AS “YOU” AND “END USER”), AGREE TO THESE TERMS AND CONDITIONS AND CREATE A BINDING CONTRACT BETWEEN YOU AND AVAYA INC. OR THE APPLICABLE AVAYA AFFILIATE (“AVAYA”).
Avaya grants End User a license within the scope of the license types described below. The applicable number of licenses and units of capacity for which the license is granted will be one (1), unless a different number of licenses or units of capacity is specified in the Documentation or other materials available to End User. "Designated Processor" means a single stand-alone computing device. "Server" means a Designated Processor that hosts a software application to be accessed by multiple users. "Software" means the computer programs in object code, originally licensed by Avaya and ultimately utilized by End User, whether as stand-alone products or pre-installed on Hardware. "Hardware" means the standard hardware originally sold by Avaya and ultimately utilized by End User.
License types Designated System(s) License (DS). End User may install and use each copy of the Software on only one Designated Processor, unless a different number of Designated Processors is indicated in the Documentation or other materials available to End User. Avaya may require the Designated Processor(s) to be identified by type, serial number, feature key, location or other specific designation, or to be provided by End User to Avaya through electronic means established by Avaya specifically for this purpose.
Copyright Except where expressly stated otherwise, no use should be made of materials on this site, the Documentation(s) and Product(s) provided by Avaya. All content on this site, the documentation(s) and the product(s) provided by Avaya including the selection, arrangement and design of the content is owned either by Avaya or its licensors and is protected by copyright and other intellectual property laws including the sui generis rights relating to the protection of databases. You may not modify, copy, reproduce, republish, upload, post, transmit or distribute in any way any content, in whole or in part, including any code and software. Unauthorized reproduction, transmission, dissemination, storage, and or use without the express written consent of Avaya can be a criminal, as well as a civil, offense under the applicable law.
Third Party Components Certain software programs or portions thereof included in the Product may contain software distributed under third party agreements ("Third Party Components"), which may contain terms that expand or limit rights to use certain portions of the Product ("Third Party Terms"). Information regarding distributed Linux OS source code (for those Products that have distributed the Linux OS source code), and identifying the copyright holders of the Third Party Components and the Third Party Terms that apply to them is available on the Avaya Support Web site: http://support.avaya.com/Copyright.
Preventing toll fraud "Toll fraud" is the unauthorized use of your telecommunications system by an unauthorized party (for example, a person who is not a corporate employee, agent, subcontractor, or is not working on your company's behalf). Be aware that there can be a risk of toll fraud associated with your system and that, if toll fraud occurs, it can result in substantial additional charges for your telecommunications services.
Avaya fraud intervention If you suspect that you are being victimized by toll fraud and you need technical assistance or support, call Technical Service Center Toll Fraud Intervention Hotline at +1-800-643-2353 for the United States and Canada. For additional support telephone numbers, see the Avaya Support Web site: http://support.avaya.com Suspected security vulnerabilities with Avaya products should be reported to Avaya by sending mail to: securityalerts@avaya.com.
Trademarks Avaya and Aura are trademarks of Avaya, Inc. The trademarks, logos and service marks (“Marks”) displayed in this site, the documentation(s) and product(s) provided by Avaya are the registered or unregistered Marks of Avaya, its affiliates, or other third parties. Users are not permitted to use such Marks without prior written consent from Avaya or such third party which may own the Mark. Nothing contained in this site, the documentation(s) and product(s) should be construed as granting, by implication, estoppel, or otherwise, any license or right in and to the Marks without the express written permission of Avaya or the applicable third party. Avaya is a registered trademark of Avaya Inc. All non-Avaya trademarks are the property of their respective owners.
Downloading documents For the most current versions of documentation, see the Avaya Support Web site: http://www.avaya.com/support
Contact Avaya Support Avaya provides a telephone number for you to use to report problems or to ask questions about your product. The support telephone number is 1-800-242-2121 in the United States. For additional support telephone numbers, see the Avaya Web site: http://www.avaya.com/support
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 2
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 3
Contents
Contents
..................................................................... 506.5 Deleting All Records
..................................................................... 506.6 Adding a Record to Your Contacts
Introduction1.
..................................................................... 81.1 9500 Series 04 Telephones
..................................................................... 91.2 9500 Series 08 Telephones
..................................................................... 101.3 Dialing Codes
..................................................................... 111.4 Feature Codes
Call Handling2.
..................................................................... 142.1 Making Calls
............................................................................ 142.1.1 Making Internal Calls
............................................................................ 142.1.2 Setting a Callback
............................................................................ 152.1.3 Making External Calls
............................................................................ 162.1.4 Making Page or Direct Calls
............................................................................ 162.1.5 Redial
..................................................................... 172.2 Answering Calls
............................................................................ 172.2.1 Answer a Page Call
............................................................................ 182.2.2 Call Pickup
..................................................................... 192.3 Speed Dialing
............................................................................ 192.3.1 System Speed Dials
............................................................................ 202.3.2 Personal Speed Dials
............................................................................ 212.3.3 Auto Dialing
..................................................................... 222.4 Adjusting the Volume
..................................................................... 222.5 Mute
..................................................................... 232.6 Holding Calls
..................................................................... 232.7 Parking Calls
..................................................................... 242.8 Transferring Calls
............................................................................ 242.8.1 Voice Mailbox Transfer
..................................................................... 252.9 Conferencing Calls
..................................................................... 262.10 Using Handsfree
..................................................................... 272.11 Using a Headset
..................................................................... 272.12 Joining Calls
Button Programming7.
..................................................................... 527.1 Programming a Button
..................................................................... 537.2 Changing a Button Label
..................................................................... 547.3 Button Functions
Phone Settings8.
..................................................................... 588.1 Naming Your Extension
..................................................................... 598.2 Visual Alerting
..................................................................... 598.3 Audible Alerting
..................................................................... 598.4 Ringer Sound
..................................................................... 608.5 Ringer Volume
..................................................................... 608.6 Display Brightness
..................................................................... 608.7 Display Contrast
..................................................................... 608.8 Display Language
..................................................................... 618.9 Error Tones
..................................................................... 618.10 Button Clicks
..................................................................... 618.11 Default Handsfree Audio Path
..................................................................... 628.12 The Admin Menu
..................................................................... 638.13 The A MENU
..................................................................... 648.14 A-Menu Auto Exit
...............................................................................65Index
Other Features3.
..................................................................... 303.1 Absent Text Messages
..................................................................... 313.2 Forwarding Calls
..................................................................... 323.3 Call Coverage
..................................................................... 343.4 Locking Your Extension
..................................................................... 353.5 Account Codes
..................................................................... 363.6 Do Not Disturb
............................................................................ 373.6.1 Do Not Disturb Exceptions
Using Voicemail4.
..................................................................... 414.1 Voicemail Coverage On/Off
Contacts5.
..................................................................... 445.1 Viewing Contacts Details
..................................................................... 455.2 Make a Call from the Directory
..................................................................... 455.3 Editing a Contact
..................................................................... 465.4 Adding a New Contact
............................................................................ 465.4.1 Add a Contact from the Call Log
..................................................................... 465.5 Deleting a Contact
Call Log6.
..................................................................... 486.1 Using the Call Log
..................................................................... 486.2 Making a Call from the Call Log
..................................................................... 496.3 Viewing Call Details
..................................................................... 506.4 Deleting a Record
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 3
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 4
Page 5
Chapter 1.
Introduction
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 5
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 6
Page 7
Introduction:
1. Introduction
This guide covers the basic operation of 9500 Series phones on a IP Office Basic Edition - Quick Mode phone system.
Key System or PBX System
The IP Office Basic Edition - Quick Mode system can operate in either of two modes; key mode or PBX mode. Your system administrator will confirm the mode being used by your system. The mode affects the order and role of some of the buttons on your phone.
Programmable Buttons
Each of the phones has a number of programmable buttons. The function of each such button is set either by the telephone system or by your system administrator or can be set by yourself. The role of the first few buttons is determined by whether your system is set to key system or PBX system mode.
Key System Mode
· Intercom Buttons The first two programmable buttons are set as Intercom buttons and cannot be changed. These buttons are used to make and receive internal calls.
· Line Appearance Buttons The next buttons are set as line buttons by your system administrator. These buttons are used to make and receive external calls. Your system administrator can adjust the number of line appearance buttons on your phone and which lines they represent.
· Other Buttons Any remaining buttons can be programmed for a range of features. This is done by your system administrator or by yourself through the phone's menus. For more information refer to the IP Office Basic Edition - Quick Mode Phone Base Administration manual.
PBX System Mode
· Call Appearance Buttons For a system in PBX system mode, the first three programmable buttons are set call appearance buttons. These buttons are used to make and receive internal and external calls.
· Line Appearance Buttons Your system administrator can assign the next buttons as line appearance buttons if required. This allows you to make and answer calls on a specific line if required.
· Other Buttons Any remaining buttons can be programmed for a range of features. This is done by your system administrator or by yourself through the phone's menus. For more information refer to the IP Office Basic Edition - Quick Mode Phone Base Administration manual.
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 7
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 8
1.1 9500 Series 04 Telephones
Page 1
Page 2
010302
04 050706
08
The programmable buttons are arranged in 2 pages of 4 to match the 4 physical buttons. The buttons are numbered from top-down, left to right on each page. The left arrow and right arrow buttons are used to switch between pages during normal operation.
The button numbering order on these phones does not depend on the system mode. However, the default button usage is affected by the system mode.
· For systems running in key system mode, the first two programmable buttons, 01 and 02, are fixed as Intercom 1 and Intercom 2 buttons.
· For systems running in PBX system mode, the first three buttons, 01 to 03, are fixed as call appearance buttons.
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 8
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 9
Introduction: 9500 Series 04 Telephones
Page 1
Page 2
Page 3
01050206030704
08 09131014111512
16 17211822192320
24
1.2 9500 Series 08 Telephones
The programmable buttons are arranged in 3 pages of 8 to match the 8 physical buttons. The buttons are numbered from top-down, left to right on each page. The left arrow and right arrow buttons are used to switch between pages during normal operation.
The button numbering order on these phones does not depend on the system mode. However, the default button usage is affected by the system mode.
· For systems running in key system mode, the first two programmable buttons, 01 and 02, are fixed as Intercom 1 and Intercom 2 buttons.
· For systems running in PBX system mode, the first three buttons, 01 to 03, are fixed as call appearance buttons.
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 9
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 10
1.3 Dialing Codes
Feature
Dial
Summary
Call Pickup
6 <Extension Number>
Answer the longest waiting call ringing at an extension.
Group Pickup
66 <Pickup Group>
Answer the longest waiting call ringing any extension that is a member of the pickup group (1 to 4) selected.
Idle Line Pickup
8 <Line Number>
Seize the specified line if it is idle and then make a call using that line.
Active Line Pickup
68 <Line Number>
Answer or seize the call on the specified line.
Loudspeaker Paging
70
Page the loudspeaker device attached to the system.
Simultaneous Paging
*70
Page both the loudspeaker device attached to the system and the extensions in calling group 71.
Group Calling – Ring
7 <Calling Group>
Call the available extensions in one of the calling groups (1 to 4).
Group Calling – Page
*7 <Calling Group>
Page the available extensions in one of the calling groups (1 to
4).
Group Hunting – Ring
77 <Hunt Group>
Call the available extensions in one of the hunt groups (1 to 6).
Group Hunting – Page
*77 <Hunt Group>
Page the first available extension in one of the hunt groups (1 to
6).
The following features can be used by dialing the appropriate number.
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 10
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 11
Introduction: Dialing Codes
Feature
Code
Description
Do Not Disturb
01
This function allows you to switch do not disturb on or off.
" Cancel
01
Recall
03
This function allows you to send a recall or hook flash signal.
Save Number Redial
04
This function allows you to save the number dialed during a call and to redial that number when idle. This can be used when the number dialed does not answer.
Last Number Redial
05
This function allows you to redial the last external number dialed.
Conference Drop
06
This function allows you to select and drop a call from a conference.
Privacy
07
This function allows you to turn privacy on or off. When on, other extensions are not able to bridge into your calls.
Call Forward
11
This function allows you to redirect all your calls to another number. If the system administrator has configured your for Remote Call Forwarding, you can forward calls externally by specifying a personal speed dial as the destination.
Call Forward Cancel
11
Account Code Entry
12
This function allows you to enter an account code prior to making a call or during a call.
Voice Mailbox Transfer
14
This function allows you to transfer your current call to another extension's mailbox. Your current call is put on hold and you enter the target extension number to indicate the mailbox required.
VMS Cover
15
This function allows the you to switch use of voicemail coverage for your extension on or off.
Caller ID Name Display
16
This function allows you to swap the display of caller ID name and number information on the phone.
Caller ID Inspect
17
This function allows you to see the caller ID of a call on another line without interrupting the current call to which you are connected.
Call Coverage
20
This function allows you to switch call coverage on or off. When on, any calls to you that ring unanswered also start ringing at your call coverage extension.
Station Lock
21
This function allows you to lock and unlock your extension from being used to make calls. When selected, you are prompted to enter a four digit code after which the extension is locked. If the extension is already locked, use of this function prompts for reentry of the four digit code to unlock the extension.
Station Unlock
22
This function can only be used by the first two extensions in the system. It allows the user to unlock any extension without needing to know the code that was used to lock that extension.
Caller ID Log
23
This function allows you to view the phone system's call log of all caller IDs of calls received by the system. To use this you must be one of the three extensions configured for call ID logging by your system administrator.
Hot Dial
26
This function allows you to dial a stored number without first going off hook or pressing the SPEAKER button.
Absent Message
28
This function allows you to set or clear an absent message for display on you phone. When set, the absent message is also displayed on other extensions when they call the user.
Contact Closure 1
41
This function you to operate the system's contact closure 1 or 2 connection. To use this you must be a member of the system's contact closure group.
Contact Closure 2
42
System Release
590
Displays the core software level that the system is running.
System IP Address
591
Displays the IP address of the systems LAN port.
1.4 Feature Codes
The following feature codes can be dialed from most phones after pressing Feature. Most of these features can also be assigned to programmable buttons.
36
36
16
25
27
31
31
35
24
41
32
34
34
30
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 11
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 12
Feature
Code
Description
SD Card Serial Number
592
Displays the feature key number of the System SD card. This is the number used for validation of licenses entered into the system configuration.
System Speed Dial
600 to 699
Dial the selected system speed dial number.
Personal Speed Dial
80 to 99
Dial the selected personal speed dial number.
DND Exception Numbers
700 to 719
Set a DND exception number.
19
20
36
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 12
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 13
Chapter 2.
Call Handling
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 13
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 14
2. Call Handling
Feature
Dial
Summary
Loudspeaker Paging
70
Page the loudspeaker device attached to the system.
Simultaneous Paging
*70
Page both the loudspeaker device attached to the system and the extensions in calling group 71.
Group Calling – Ring
7 <Calling Group>
Call the available extensions in one of the calling groups (1 to 4).
Group Calling – Page
*7 <Calling Group>
Page the available extensions in one of the calling groups (1 to 4).
Group Hunting – Ring
77 <Hunt Group>
Call the available extensions in one of the hunt groups (1 to 6).
Group Hunting – Page
*77 <Hunt Group>
Page the first available extension in one of the hunt groups (1 to 6).
2.1 Making Calls
2.1.1 Making Internal Calls
If already on a call, end the call by pressing Drop or put it on hold by either pressing Hold or pressing the
1.
button which the call is on.
Press an idle Intercom or Call Appearance button.
2.
Dial the extension number or the code for the feature you wanted to access.
3.
· To call an extension: Dial the extension number. If you put a * in front of the extension number, the system will attempt to make a
direct voice call .
· To call a group or attempt a call pickup: Dial one of the numbers in the table below. If you put a * in front of the group number, the system will make a page call .
16
16
23
You will hear the call progress. You can continue the call handsfree or switch to using the handset or headset (press
2. the HEADSET button).
· If the other extension doesn't answer, press AutCB or Callback to have the system call you when that extension is next free.
2.1.2 Setting a Callback
If the call is to a user, and they do not answer, you can set a callback. When a callback is set, when the other user next uses their phone or ends their current call, the system will call you and when you answer, automatically makes another call to the user.
To Set a Callback
While the call is still ringing or if you hear busy. Press Callback.
1.
End your call attempt by replacing the handset or pressing Drop.
2.
To Clear a Callback
If you have a callback set, you can cancel it using the following process:
Press Feature #2.
1.
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 14
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 15
Call Handling: Making Calls
2.1.3 Making External Calls
If already on a call, end the call by pressing Drop or put it on hold by either pressing Hold or pressing the
1. button which the call is on.
Press an idle Line Appearance or Call Appearance button.
2.
Dial the telephone number.
3.
· If using a Call Appearance button, some systems may require you to dialing a specific prefix when making external calls. Your system administrator will inform you if a prefix is required.
· To dial a personal speed dial , press FEATURE or # and select the speed dial between 80 and 89.
· To dial a system speed dial , press FEATURE or # and select a speed dial between 600 to 699.
· To select a number from the directory press CONTACTS.
You will hear the call progress. You can continue the call handsfree or switch to using the handset or headset (press
4. the HEADSET button).
20
19
23
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 15
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 16
2.1.4 Making Page or Direct Calls
You can make calls that are automatically answered if the extension or extensions called support auto answer. There are two methods: page calls and direct voice calls, however the method for making both types of call is much the same.
To Make a Direct Voice Call
For a call to an individual extension, putting * in front of the extension number of the user being called makes the call a direct voice call. If supported by the phone being called, the call is automatically answered after the called users hears 3 beeps.
Unlike a page call, the called user can also speak without having to take any further action if their phone has a handsfree microphone. Otherwise they need to pickup the handset to be heard.
If the user called is already on a call when you attempt a direct voice call to them, you call is turned into a normal waiting call.
If already on a call, end the call by pressing Drop or put it on hold by either pressing Hold or pressing the
1. button which the call is on.
Dial * and then the extension number of the user.
2.
· If the user's phone is idle and supports auto answer, you can speak and be heard by them immediately. You can also hear them.
· If you hearing ringing, then either the user called already has another call in progress or has a phone that does not support answer.
To Make a Page Call
For a call to a group of extensions, putting a * in front of the extension number of the group being called make the call a page call. The group type is ignored, instead, all users who are members of the group, have phones that support auto answer and are currently not on another call, hear a single beep and can then hear you. However, you cannot hear the group members.
One of users being paged can answer the page if they want to. That turns the page call into a normal call between just you and the answering user.
If already on a call, end the call by pressing Drop or put it on hold by either pressing Hold or pressing the
2. button which the call is on.
Dial * and then the extension number of the group.
2.
17
23
23
To Page the Loudspeaker Device
The telephone system can include a connection to a loudspeaker paging device. To page this device make a normal internal call to the extension number 70. If you make an internal call to *70, you will page both the loudspeaker device and the available users in the calling group 71.
2.1.5 Redial

Press Redial. On 9500 Series phones, this is a display soft key on idle phones.

1.
The display will show you your outgoing call log.
2.
Use the up and down arrow keys to scroll through the records.
3.
When the name or number required is shown, press Call.
4.
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 16
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 17
Call Handling: Making Calls
2.2 Answering Calls
You can answer telephone calls that are ringing your extension or at another extension. If you regularly pick up calls for a specific extension you can program a call pickup button for that specified extension.
52
If already on a call, end the call by pressing Drop or put it on hold by either pressing Hold or pressing the
1. button which the call is on.
While the call is alerting, additional options may be displayed.
2.
· To VM This option sends the ringing call to voicemail to leave a message in your mailbox.
· Ignore This option does not affect the incoming calls but temporarily turns off the ringer.
· Drop This option can be used to end the call without answering it.
· Answer This option can be used to answer the call. The call is connected to either the speaker or headset depending on the phone's Default Handsfree Audio Path Setting.
If you pick up the handset or press SPEAKER or press HEADSET, you are connected to the incoming call.
3.
· To answer a call alerting on a specific line, press that button.
23
2.2.1 Answer a Page Call
There are two type of calls which your phone will automatically answer the call so that you automatically hear the caller. This will only happen if your phone is currently idle, ie. not on another call.
Three Beeps
A call connected automatically after three beeps is a direct voice call to your extension only.
The call is connected and answered automatically. You can speak to the caller without taking any further action.
1.
Single Beep
A call connected automatically after a single beep is a page call a group of which your phone is a member. You can hear the caller but they cannot hear you.
You can answer the call, turning it into a normal call between just you and the caller. Press Answer. You can
1. continue handsfree or pickup the handset.
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 17
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 18
2.2.2 Call Pickup
If you hear another phone ringing, there are a number of ways that you can answer the call if you know the user, group or line being called.
If already on a call, end the call by pressing Drop or put it on hold by either pressing Hold or pressing the
1. button which the call is on.
Press an idle Intercom or Call Appearance button.
2.
· To pickup a call ringing at a particular extension: Dial 6 followed by the extension number at which the call is ringing or parked.
· To pickup the longest waiting call in a pickup group: Dial 66 followed by the pickup group number (1 to 4).
· To pickup the call ringing on a particular line:
Dial 68 followed by the two digit line number.
You can continue the call handsfree or switch to using the handset or headset (press the HEADSET button).
3.
23
To Create a Call Pickup Button
Press the Admin soft key on the display.
1.
· During a call, press the PHONE button to display the Admin soft key option. If you access phone
administration during a call, only the SPEAKER, MUTE and HEADSET buttons still affect the connected call.
Use the up or down arrow buttons to scroll to Telephone Programming. Press Select.
2.
Press the programmable button you want to change. Alternatively:
3.
· Use the up or down arrows to scroll to Button Programming. Press Select.
· At the Button: prompt press the button to edit or enter from the button number.
The current setting of that button is displayed.
4.
Press Program and either press Intercom 1 or use the up or down arrow buttons to scroll the display to Call
5. Pickup and press Select.
At the Endpoint: prompt enter 6 followed by the target extension.
6.

The current setting of the button will now be Call Pickup followed by the target extension number.

7.
· Exit phone administration by pressing the PHONE button. Alternatively use the Back button to move to
another menu.
To Use a Call Pickup Button
Press the Call Pickup programmed button for the specified extension number. You are connected to the call that
1. was ringing the specified extension.
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 18
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 19
Call Handling: Answering Calls
2.3 Speed Dialing
There are a number of ways that you can dial a stored number.
2.3.1 System Speed Dials
The system administrator can program up to 100 frequently used number as system speed dial numbers 600 to 699. Any user in the system can use a system speed dial by pressing FEATURE and dialing the three digit code of the system speed dial required.
· Except in special cases which the system administrator can configure, system speed dials do not override any
dialing restrictions that apply to an extension.
· Phone users can also view and use system speed dials through the phone's CONTACTS menu.
· The first two extensions on the system can also edit the system speed dials through the CONTACTS menu.
44
To Use a System Speed Dial
If already on a call, end the call by pressing Drop or put it on hold by either pressing Hold or pressing the
1. button which the call is on.
Press FEATURE or # and dial the three digit system speed dial code between 600 and 699.
2.
The stored number is dialed.
3.
23
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 19
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 20
2.3.2 Personal Speed Dials
Function
Character
Description
Pause
P
Inserts a 1.5 second pause.
Recall
R
Send a hook-switch flash signal.
Stop
S
Stop dialing.
You can create up to 20 personal speed dial codes, 80 to 99, to store frequently dialed numbers. The numbers can be quickly dialed by pressing FEATURE and the two-digit code for that personal speed dial.
The personal speed dial numbers programmed for a particular extension can only be used at that extension.
· If the system is connected to a PBX or Centrex system and a dial-out code (usually 9) is needed to place calls
outside the PBX or Centrex system, include the dial-out code in Speed Dial numbers that must dial out of the PBX or Centrex system.
· Personal speed dials do not override any dialing restrictions that apply to an extension.
· Phone users can view, use and edit their personal speed dials through the phone's CONTACTS menu.
To Use a Personal Speed Dial
If already on a call, end the call by pressing Drop or put it on hold by either pressing Hold or pressing the
1. button which the call is on.
Press FEATURE or # and dial the two digit personal speed dial code between 80 and 99.
2.
The stored number is dialed.
3.
23
To Edit Your Personal Speed Dials
Press the Admin soft key on the display.
1.
· During a call, press the PHONE button to display the Admin soft key option. If you access phone
administration during a call, only the SPEAKER, MUTE and HEADSET buttons still affect the connected call.
Use the up or down arrow buttons to scroll to Telephone Programming. Press Select.
2.
Use the up or down arrow buttons to scroll the display to Personal Speed Dial. When displayed, press
3. Select.
At the Code: prompt enter between 80 and 99 to select the speed dial entry that you want to edit.
4.
The current setting of the speed dial entry is displayed.
5.
To enter a number press Enter, dial the number and press Enter. To remove the number press Clear.
6.
· The number can be up to 28 characters in length.
· If your system uses an external dialing prefix, remember to include the prefix.
· These options are accessed by pressing More and then selecting Pause, Stop or Recall as required.
44
· Exit phone administration by pressing the PHONE button. Alternatively use the Back button to move to
another menu.
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 20
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 21
Call Handling: Speed Dialing
Function
Character
Description
Pause
P
Inserts a 1.5 second pause.
Recall
R
Send a hook-switch flash signal.
Stop
S
Stop dialing.
2.3.3 Auto Dialing
An auto dialing button is used to store a frequently used or important number. Whenever the number needs to be dialed, pressing the button will dial the stored number.
To Use an Auto Dial Button
At dial tone or whenever you want to dial a number, press the programmed auto dial button.
1.
The stored number is dialed.
2.
To Create an Auto Dial - Other Button
Press the Admin soft key on the display.
1.
· During a call, press the PHONE button to display the Admin soft key option. If you access phone
administration during a call, only the SPEAKER, MUTE and HEADSET buttons still affect the connected call.
Use the up or down arrow buttons to scroll to Telephone Programming. Press Select.
2.
Press the programmable button you want to change. Alternatively:
3.
· Use the up or down arrows to scroll to Button Programming. Press Select.
· At the Button: prompt press the button to edit or enter from the button number.
The current setting of that button is displayed.
4.
Press Program and either press Intercom 2 or use the up or down arrow buttons to scroll the display to
5. Auto Dial - Other and press Select.
At the AD-O: prompt enter the number for calls made using the button. The number can include * and # and the
6. following special characters:
· These options are accessed by pressing More and then selecting Pause, Stop or Recall as required.
The current setting of the button will now be AD-O followed by the stored number.
7.
To remove the current setting press Clear.
8.
· Exit phone administration by pressing the PHONE button. Alternatively use the Back button to move to
another menu.
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 21
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 22
2.4 Adjusting the Volume
While the phone is connected to a call you can adjust the volume. The volume that gets adjusted will depend on whether you are using the handset, speakerphone or headset at the time you use this process.
Use the up arrow and down arrow keys to change the volume.
1.
2.5 Mute
While on a call, you can temporarily turn off the microphone so that the caller cannot hear you. You however will still be able to hear the caller.

To mute the microphone press the Mute key. While mute is active, the button is lit.

IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 22
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 23
Call Handling: Mute
2.6 Holding Calls
When you put a call on hold, you can make and receive other calls. However, if a call is left on hold for to long, by default 15 seconds, it will automatically alert your phone again if you are not on another call
To Put a Call on Hold
During the call, either press the HOLD button or press the button on which the call is taking place. The Green light
1. next to the button will change to fast flashing green to show there is a call on hold.
To Return to a Call Put on Hold
If already on a call, end the call by pressing Drop or put it on hold by either pressing Hold or pressing the
1. button which the call is on.
Press the button next to the fast flashing Green light. You are connected to the call. The light changes to steady.
2.
23
2.7 Parking Calls
Use this feature to place a call on a special type of hold where it can be retrieved from any extension in the system.
· You should park only one call at a time to ensure that you know which caller you are talking to when you retrieve
the parked call.
· If you frequently park calls, program your extension number on an Auto Dial button, so you can park a call
simply by pressing that button during the park process.
To Park a Call
While on a call, press TRANSFER and and dial your own extension number.
1.
Hang up. If the call is not picked up within three minutes, it rings back at your extension.
2.
To Retrieve a Parked Call
Press an Intercom or Call Appearance button and 6 followed by the extension number of the extension that
1. parked the call.
21
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 23
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 24
2.8 Transferring Calls
You can transfer a call to another extension.
While the call is active, press TRANSFER. The call is put on hold and the green light next to the button flashes
1. rapidly.
Make a call to the transfer destination. Then do one of the following:
2.
· To transfer the call without announcing it (an unsupervised or blind transfer) hang up or press the Transfer button again. You can do this as soon as you hear ringing. The transfer is complete. If the call is not answered it will be returned to your extension. When your extension rings, lift the handset to be reconnected to the caller.
· To announce the call before completing the transfer (a supervised transfer), wait for the call to be answered. If the called party is willing to accept the call hang up or press Transfer again. If no one answers or the call is refused, press the button next to the fast flashing green light to be reconnected to the original caller.
2.8.1 Voice Mailbox Transfer
You can transfer a caller to directly to an extension's voice mailbox for the caller to leave a message without first ringing the extension. This feature is useful when you know that the extension user is not present and has not set do not disturb.
You can program a voice mailbox transfer button to transfer a caller directly to a voice mailbox by pressing the button and then dialing the mailbox subscriber's extension number.
To Transfer a Caller to an Extensions Mailbox
During the call press FEATURE 14 or press a Voice Mailbox Transfer button you have one programmed.
1.
Dial the two digit extension number of the extension for which the caller wants to leave a message. The caller is
2. routed to the mailbox and hears the recorded greeting for that mailbox.
Hang up.
3.
To Create a Voice Mailbox Transfer Button
Press the Admin soft key on the display.
1.
· During a call, press the PHONE button to display the Admin soft key option. If you access phone
administration during a call, only the SPEAKER, MUTE and HEADSET buttons still affect the connected call.
Use the up or down arrow buttons to scroll to Telephone Programming. Press Select.
2.
Press the programmable button you want to change. Alternatively:
3.
· Use the up or down arrows to scroll to Button Programming. Press Select.
· At the Button: prompt press the button to edit or enter from the button number.
The current setting of that button is displayed.
4.
Press Program and either dial #14 or use the up or down arrow buttons to scroll the display to Voice
5. Mailbox Transfer and press Select.

The current setting of the button will now be set to Voice Mailbox Transfer.

6.
· Exit phone administration by pressing the PHONE button. Alternatively use the Back button to move to
another menu.
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 24
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 25
Call Handling: Transferring Calls
2.9 Conferencing Calls
The Conference feature allows you to conference other parties (including yourself) into a call. The system supports multiple conferences of up to 64 parties in total, including up to 2 external analog trunk in each conference.
To Create a Conference Call
While active on a call, press CONF. The first party is now on hold.
1.
When you hear dial tone, dial the telephone number of the second party.
2.
When the call is answered, press CONF again. The second party is added to the call the call. All parties hear a
3. single beep to indicate that they are in a conference call.
You can now speak to the first and second parties.
4.
Repeat step 2 to add more parties.
5.
To Hold a Conference Call
If you need to answer or make another call during a conference, you can hold in the same way as for normal calls. When you put a conference call on hold, the other parties can still talk to each other.
· ! WARNING
Only hold a conference that you know is taking place on your own telephone system. If you hold a conference that you have joined on another telephone system, that conference will hear hold music.
Press the HOLD button. The Green light next to the button will fast flash to show that the call is on hold.
1.
To re-join the conference call press the button next to the Green light. You will rejoin the conference.
2.
23
To Drop Other Parties from the Call
While in the conference, press Details.
1.
Scroll through the parties in the conference.
2.
When the party you want to drop is shown, press Drop.
3.
To Mute Other Parties
While in the conference, press Details.
1.
Scroll through the parties in the conference.
2.
When the party you want to drop is shown, press Drop.
3.
To Remove Yourself from a Conference Call
While in the conference call, press Drop twice.
1.
The remaining parties on the conference hear a double beep.
2.
The remaining parties on the conference can still talk to each other. When only one party remains on the call, the
3. call is disconnected.
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 25
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 26
2.10 Using Handsfree
The telephone has a speaker and microphone which you can control using the SPEAKER button.
· To make and answer calls handsfree, use the SPEAKER button in the same way as lifting or replacing the
handset. The button is lit while the phone is in handsfree mode.
· When you make or answer calls by first pressing an Intercom, Call Appearance or Line Appearance button, the
call is automatically connected either on the speaker or headset. Which is used is set by the phone's Default
Hands Audio Path setting.
· If already using the handset, you can switch to handsfree by pressing SPEAKER. You can then replace the
handset.
· If already connected to a call handsfree, lifting the handset will end the handsfree.
Note
Room acoustics and background noise can affect the proper operation of the speakerphone. To ensure that your speakerphone works effectively, follow these guidelines:
· Avoid placing your telephone in areas with high background noise caused by sources such as motor vehicles,
manufacturing equipment, loud voices, radios, printers, copiers, typewriters, other noisy office equipment or heater and air conditioning fans.
· Avoid talking before the other person is finished speaking. When you both talk at the same time, only one person’s
voice comes through.
· Do not use your speaker to make announcements over a loudspeaker paging system connected to your telephone
system.
· When talking, always face your telephone and stay within two feet of it.
· Place your telephone at least six inches (15 cm) away from the edge of your desk.
· If you have difficulty hearing the other party, try increasing the speaker volume. If you have background noise, try
turning off the microphone when the party at the other end is speaking and turning it on when you speak. If the difficulty persists, lift your handset to continue the conversation.
· In conference rooms, a separate speakerphone is recommended, since the built-in speaker on a system telephone
is designed for individual use.
61
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 26
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 27
Call Handling: Using Handsfree
2.11 Using a Headset
The telephone has a headset socket which you can control using the HEADSET button.
· To make and answer calls on the headset, use the HEADSET button in the same way as lifting or replacing the
handset. The button is lit while the phone is in headset mode.
· Remaining in Headset Mode If you use the DROP key to end a headset call, the phone will remain in headset mode. New calls will alert on the headset. You can use the Intercom, Call Appearance, Line Appearance and Drop buttons to make and answer calls while remaining in headset mode.
· If not already in headset mode, when you make or answer calls by first pressing an Intercom, Call Appearance or Line Appearance button, the call is automatically connected either on the speaker or headset. Which is used is set by the phone's Default Hands Audio Path setting.
· If already using the handset, you can switch to headset by pressing HEADSET. You can then replace the handset.
61
2.12 Joining Calls
Joining is adding yourself to a call in progress.
· You cannot:
· Join an internal call or a conference call at another extension.
· Join a call at any extension where the extension user has privacy enabled.
· Put a joined call on hold.
· You can:
· Tell when someone has joined your call when you hear a single beep.
· Use privacy to allow or prevent others from joining your calls.
· Join a call that is being answered by the voice messaging system. When you join the call, the voice messaging
system disconnects automatically so you can speak to the caller.
· Dial 68 <Line Number>to join a call on that line if a line is not assigned to a button on your extension.
To Join a Call
A steady red light next to a line button indicates that a call is in progress on that line.
If already on a call, end the call by pressing Drop or put it on hold by either pressing Hold or pressing the
1.
button which the call is on.
Press the line button next the the steady red light and lift the handset. Alternatively, press and Intercom or Call
2.
Appearance button and dial 68 followed by the two-digit line number.
You are now joined with the call. All parties on the call hear a single beep.
3.
23
To Switch Privacy On or Off
You can use the privacy feature to stop people joining your current call. You can either assign the function to a programmable button or you can dial Feature 07 to turn privacy on or off.
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 27
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 28
Page 29
Chapter 3.
Other Features
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 29
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 30
3. Other Features
· Back soon
· Do not disturb
· Out to lunch
· Away from desk
· Please Call
· At lunch until
· Don't disturb until
· With cust.til
· Back tomorrow
· On Vacation
· At home
· Be right back
· On Holiday until
· Meeting until
· With visitors until
3.1 Absent Text Messages
The absent text message feature assists internal callers by displaying a message on their telephone. When another extension calls your extension, your active absent text message appears on the caller's display.
To set and clear an absent text message you need to assign the feature to a programmable button with lights. The button can then be used to activate, select and deactivate the message.
To Create an Absent Message Button
Press the Admin soft key on the display.
1.
· During a call, press the PHONE button to display the Admin soft key option. If you access phone
administration during a call, only the SPEAKER, MUTE and HEADSET buttons still affect the connected call.
Use the up or down arrow buttons to scroll to Telephone Programming. Press Select.
2.
Press the programmable button you want to change. Alternatively:
3.
· Use the up or down arrows to scroll to Button Programming. Press Select.
· At the Button: prompt press the button to edit or enter from the button number.
The current setting of that button is displayed.
4.
Press Program and either dial #28 or use the up or down arrow buttons to scroll the display to Absent
5.
Message and press Select.
The current setting of the button will now be set to Absent Message.
6.
· Exit phone administration by pressing the PHONE button. Alternatively use the Back button to move to another menu.
To Activate an Absent Text Message
Press the absent text message button. The first absent text message is displayed.
1.
Scroll through the default messages by pressing the button beneath the word Next until the required message is
2.
displayed.
Press the button beneath the word Activ to select the message shown on the display.
3.
To add additional text or edit the existing text, press More and then Edit.
4.
To complete the process press the absent text message button again.
5.
To Deactivate the Absent Text Message
Press the absent text message button.
1.
Press the button beneath the word Dactiv.
2.
To complete the process press the absent text message button again.
3.
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 30
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 31
Other Features: Absent Text Messages
3.2 Forwarding Calls
All external, internal and transferred calls directed to your extension can be diverted to a different internal extension number. You can enter the destination extension telephone number and select when calls are redirected using a programmed button.
Before you can automatically forward calls you need to assign the feature to a button with lights. The button can then be used to turn call forwarding on and off as required.
· Selected users may also be able to do remote call forwarding where they forward their calls to an external number. If that is the case, consult your system administrator, you can use your personal speed dials as the forwarding destination.
· You receive a slow interrupted intercom dialling tone when call forwarding is active.
To Manually Set Forwarding
Press FEATURE 11.
1.
Enter the number to which you want to forward calls.
2.
· Exit phone administration by pressing the PHONE button. Alternatively use the Back button to move to another menu.
To Manually Cancel Forwarding
Press FEATURE 11.
1.
Enter you own extension number as the destination.
2.
· Exit phone administration by pressing the PHONE button. Alternatively use the Back button to move to another menu.
20
To Create a Call Forwarding Button
Press the Admin soft key on the display.
1.
· During a call, press the PHONE button to display the Admin soft key option. If you access phone
administration during a call, only the SPEAKER, MUTE and HEADSET buttons still affect the connected call.
Use the up or down arrow buttons to scroll to Telephone Programming. Press Select.
2.
Press the programmable button you want to change. Alternatively:
3.
· Use the up or down arrows to scroll to Button Programming. Press Select.
· At the Button: prompt press the button to edit or enter from the button number.
The current setting of that button is displayed.
4.
Press Program and either dial #11 or use the up or down arrow buttons to scroll the display to Call
5.
Forwarding and press Select.
At the Call Coverage Orig: prompt enter the extension number for which the button is being programmed.
6.
At the Call Coverage Dest: prompt enter the destination extension number for the call coverage calls.
7.
· To forward to an external number, enter the personal speed dial (80 to 99) that contains the required external number.
The current setting of the button will now be set to Call Forward O <covered extension> D <destination
8. extension>.
· Exit phone administration by pressing the PHONE button. Alternatively use the Back button to move to
another menu.
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 31
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 32
3.3 Call Coverage
Call coverage is used to redirect all intercom, transferred, DID and outside calls on lines assigned to you to another extension. When call coverage is in use, covered calls are routed to the covering extension after a specified number of rings set by the system administrator.
· Group calls, forwarded calls, transfer-return calls and calls to doorphone alert extensions are not covered.
· A single extension can cover multiple extensions, however an extension can have only one covering extension.
· If you activate call coverage at your extension, for calls on a line appearance button, you still can intercept a call
rerouted to coverage by pressing the button.
· You can program call coverage on a programmable button. Use a button with lights if you want a visual indication
when your calls are being covered. When the button indicator is on, your calls are being covered; when off, call coverage is not active.
· If both call coverage and do not disturb are on, covered calls go immediately to the covering extension without
ringing the covered extension. Similarly, if call coverage is on and a call begins to ring, you can turn on Do Not
Disturb to send that call immediately for coverage.
· If an extension has call coverage and VMS Cover active, calls ring at the covering extension.
· If an extension has call coverage active without voice mail coverage, covered calls ring at the covering extension
for the specified number of call coverage rings. Outside and intercom calls continue to ring at the covering extension until the call is answered or the caller hangs up.
· For transferred calls, if the covering extension does not answer, the call goes to the transfer return extension after
the specified number of Transfer Return Rings (if VMS cover is not active).
· Call forwarding override call coverage. If an extension has call coverage and call forwarding active, calls are routed
to the call forwarding destination extension.
36
41
· If the covering extension does not answer, the call is routed to the voice mailbox of the covered extension after the specified number of VMS Cover Rings. If the covering extension has Do Not Disturb active, the call is routed immediately to voicemail.
36
To Send Calls to Coverage
Press FEATURE 20.
1.
Dial the extension number of the covering extension.
2.
To Remove Call Coverage
Press FEATURE 20.
1.
Dial your own extension number.
2.
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 32
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 33
Other Features: Call Coverage
To Create a Call Coverage Button
Press the Admin soft key on the display.
1.
· During a call, press the PHONE button to display the Admin soft key option. If you access phone
administration during a call, only the SPEAKER, MUTE and HEADSET buttons still affect the connected call.
Use the up or down arrow buttons to scroll to Telephone Programming. Press Select.
2.
Press the programmable button you want to change. Alternatively:
3.
· Use the up or down arrows to scroll to Button Programming. Press Select.
· At the Button: prompt press the button to edit or enter from the button number.
The current setting of that button is displayed.
4.
Press Program and either dial #20 or use the up or down arrow buttons to scroll the display to Call
5. Coverage and press Select.
At the Call Coverage Orig: prompt enter the extension number for which the button is being programmed.
6.
At the Call Coverage Dest: prompt enter the destination extension number for the call coverage calls.
7.
The current setting of the button will now be set to Call Coverage O <covered extension> D <destination
8. extension>.
· Exit phone administration by pressing the PHONE button. Alternatively use the Back button to move to
another menu.
To Use a Call Coverage Button
Press the programmed button. When on, if programmed on a button with a light, the light will be on.
1.
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 33
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 34
3.4 Locking Your Extension
You can use the lock feature to prevent unauthorized people from making outside calls from your extension while you are away from the extension. The user of the first extension on the system can unlock extensions without needing to know the code used to lock the phone. They can do this using FEATURE 22.
To Lock Your Extension
Press FEATURE 21.
1.
Dial a four digit code using the 0 to 9 numbers .
2.
Redial the four digit code.
3.
To Unlock Your Extension
Press FEATURE 21.
1.
Dial the four digit code you used to lock the extension.
2.
To Create a Station Lock Button
Press the Admin soft key on the display.
1.
· During a call, press the PHONE button to display the Admin soft key option. If you access phone
administration during a call, only the SPEAKER, MUTE and HEADSET buttons still affect the connected call.
Use the up or down arrow buttons to scroll to Telephone Programming. Press Select.
2.
Press the programmable button you want to change. Alternatively:
3.
· Use the up or down arrows to scroll to Button Programming. Press Select.
· At the Button: prompt press the button to edit or enter from the button number.
The current setting of that button is displayed.
4.
Press Program and either dial #21 or use the up or down arrow buttons to scroll the display to Station Lock
5. and press Select.
· The first two extensions on the system can also assign the function Station Unlock to a button for use to unlock other extensions.
· Exit phone administration by pressing the PHONE button. Alternatively use the Back button to move to another menu.
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 34
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 35
Other Features: Locking Your Extension
3.5 Account Codes
An account code is typically used to identify a department, project, or client for charge-back or tracking purposes. An account code can be either forced or optional. When an extension is set up with the forced account code feature, the user must enter an account code before they can dial outside calls
To Manually Enter an Account Code
After lifting the handset (or while already active on an outside call), press FEATURE and dial 12.
1.
Enter an account code by dialing the account code using the telephone's dial pad.
2.
Press Done.
3.
Continue with the call.
4.
To Use an Account Code Button
After lifting the handset or while already active on an outside call, press the Account Code Entry button.
1.
Enter an account code using the telephone's dial pad. Press the Account Code Entry button again or press the
2.
Done button.
Continue with the call.
3.
To Create an Account Code Entry Button
Press the Admin soft key on the display.
1.
· During a call, press the PHONE button to display the Admin soft key option. If you access phone
administration during a call, only the SPEAKER, MUTE and HEADSET buttons still affect the connected call.
Use the up or down arrow buttons to scroll to Telephone Programming. Press Select.
2.
Press the programmable button you want to change. Alternatively:
3.
· Use the up or down arrows to scroll to Button Programming. Press Select.
· At the Button: prompt press the button to edit or enter from the button number.
The current setting of that button is displayed.
4.
Press Program and either dial #12 or use the up or down arrow buttons to scroll the display to Account
5.
Code Entry and press Select.
The current setting of the button will now be set to Account Code Entry.
6.
· Exit phone administration by pressing the PHONE button. Alternatively use the Back button to move to another menu.
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 35
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 36
3.6 Do Not Disturb
Use this feature to be able to press a programmed button to prevent incoming calls for the extension from ringing (lights may still flash). You can still use the extension to make calls and to answer calls using line appearance buttons.
·
· Use Do Not Disturb when you do not want the auto attendant or the voice messaging system to transfer calls to
you.
· If you are assigned to a hunt group and you leave your desk, use Do Not Disturb so that calls to the hunt group will skip your extension and ring immediately at the next available extension in the group.
· Unanswered calls that are transferred from an extension with Do Not Disturb active, ring at that extension if they transfer return.
· If you have VMS Cover turned on, enabling Do Not Disturb will send all your calls immediately to your voicemail mailbox.
· If you have Call Coverage turned on, enabling Do Not Disturb will send all your calls immediately to the covering extension.
· An N is shown on your phone's idle display when you have Do Not Disturb enabled. If you go off-hook, you will hear interrupted dial tone.
To Manually Switch Do Not Disturb On/Off
Dial FEATURE 01. An N is shown on your phone's idle display when you have do not disturb enabled.
1.
To Create a Do Not Disturb Button
When Do Not Disturb feature is on, the button's light is lit.
Press the Admin soft key on the display.
1.
41
32
· During a call, press the PHONE button to display the Admin soft key option. If you access phone
administration during a call, only the SPEAKER, MUTE and HEADSET buttons still affect the connected call.
Use the up or down arrow buttons to scroll to Telephone Programming. Press Select.
2.
Press the programmable button you want to change. Alternatively:
3.
· Use the up or down arrows to scroll to Button Programming. Press Select.
· At the Button: prompt press the button to edit or enter from the button number.
The current setting of that button is displayed.
4.
Press Program and either dial #01 or use the up or down arrow buttons to scroll the display to Do Not
5.
Disturb and press Select.

The current setting of the button will now be set to Do Not Disturb.

6.
· Exit phone administration by pressing the PHONE button. Alternatively use the Back button to move to another menu.
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 36
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 37
Other Features: Do Not Disturb
3.6.1 Do Not Disturb Exceptions
You can create a set of up to 20 numbers, calls from which are able to still ring you even when you have do not disturb switched on. You can include wildcards in the number in order to create an exception for a range of numbers.
Press the Admin soft key on the display.
1.
· During a call, press the PHONE button to display the Admin soft key option. If you access phone
administration during a call, only the SPEAKER, MUTE and HEADSET buttons still affect the connected call.
Use the up or down arrow buttons to scroll to Telephone Programming. Press Select.
2.
Use the up or down arrow buttons to scroll the display to DND Exceptions. When shown, press Select.
3.
The current entries are displayed. Use the up or down arrow buttons to scroll through the list of numbers.
4.
· To delete the currently displayed number press Delete.
· To add a new number start dialing or press Add. Dial the number and click Save.
· To add a wildcard, press the button for the highlighted row and select Dial X (single digit wildcard) or Dial
N (multiple digits wildcard) and then press Back.
· Exit phone administration by pressing the PHONE button. Alternatively use the Back button to move to another menu.
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 37
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 38
Page 39
Chapter 4.
Using Voicemail
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 39
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 40
4. Using Voicemail
The telephone system includes embedded voicemail and each extension on the system has a voicemail mailbox by default. The message lamp on your phone is lit when you have new messages in your mailbox.
Except for special cases, for example the extensions connected to the fax machine and loudspeaker, the mailboxes are used when the extension has calls it does not answer within a set time (by default 15 seconds though this can be adjusted for each extension by the system administrator).
Your system administrator can also configure other methods of access including access to your mailbox from other phones.
· Embedded Voicemail User Guide The embedded voicemail system can operate two different ways, each of which uses different key presses once you have logged in to a mailbox. The modes are Intuity emulation mailbox mode and IP Office mailbox mode. Your system administrator will inform you which mode your system is using and provide the appropriate embedded voicemail user guide for that mode.
Accessing Your Mailbox
Press an idle intercom or call appearance button and dial 777.
1.
· To access your mailbox from another extension, dial 778 and enter your own extension number when asked which mailbox you want to access.
If your mailbox has an access code set, you will be prompted to enter it. Enter your access code and press #.
2.
You will hear a prompt telling you how many messages you have. If you have any new messages the voicemail
3. system will start playing your new messages.
IMPORTANT
Once a new message has been listened to, it is marked as 'old' and is automatically deleted after 24 hours. If you do not want the message deleted, you must mark it as 'saved' by pressing 5 while listening to the message.
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 40
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 41
Using Voicemail:
4.1 Voicemail Coverage On/Off
Calls to your extension can be rerouted to your voicemail mailbox if you do not answer the call within a set number of rings, the default being 3 rings. This is called VMS Cover. The number of rings used for your extension is set by your system administrator.
· If an extension has Call Coverage and VMS Cover active, a covered calls ring at the covered extension for the
specified number of Call Coverage Rings. It will then start ringing the covering extension. If the covering extension does not answer, the call is routed to the voice mailbox of the extension that activated Call Coverage after the specified number of VMS Cover Rings. The count of VMS cover rings starts when the covered extension initially begins to ring. If the covering extension has Do Not Disturb active, the call is routed immediately to the voice mailbox of the extension that activated Call Coverage.
· Users with VMS Cover turned on can activate Do Not Disturb to send ringing calls immediately to their voice
mailbox.
· Note that when your voicemail cover is off, you can still access the messages in your mailbox and other users can
still use forwarding to send messages to your mailbox.
To create a VMS cover button
Press the Admin soft key on the display.
1.
· During a call, press the PHONE button to display the Admin soft key option. If you access phone
administration during a call, only the SPEAKER, MUTE and HEADSET buttons still affect the connected call.
Use the up or down arrow buttons to scroll to Telephone Programming. Press Select.
2.
Press the programmable button you want to change. Alternatively:
3.
· Use the up or down arrows to scroll to Button Programming. Press Select.
· At the Button: prompt press the button to edit or enter from the button number.
The current setting of that button is displayed.
4.
Press Program and either dial #15 or use the up or down arrow buttons to scroll the display to VMS Cover
3. and press Select.
The current setting of the button will now be set to VMS Cover.
4.
32
36
36
· Exit phone administration by pressing the PHONE button. Alternatively use the Back button to move to
another menu.
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 41
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 42
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 42
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 43
Chapter 5.
Contacts
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 43
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 44
5. Contacts
The contacts directory contains system directory number, systems users and hunt groups and your own personal contacts.
This menu is accessed by pressing the key. It is used to display names and numbers that you can then use for making calls.
The directory includes names stored for use by all users, names stored for use by just you and the name and numbers of all the other users and groups on the phone system.
5.1 Viewing Contacts Details
Access the contacts directory:
1.

Press the CONTACTS key. The directory menu is displayed.

a.
Use the left and right arrow keys to select which type of directory entries you want displayed.
b.
· All All directory entries.
· Personal Your personal speed dials.
· External The system speed dials.
· Users The names and numbers of other users on the telephone system.
· Groups The names and numbers of hunt groups on the telephone system.
Either press the List soft key to display all the directory entries or start dialing the name to display only
c.
matching entries.
Use the up and down arrow keys to scroll through the matching entries. To return to the start to match a
d.
different directory selection, press the Clear soft key.
When the required entry is displayed, press Details to display the name and number.
2.
Use the up and down arrow key to switch between the name and the number.
3.
The range of soft keys available will depend on the type of directory entry:
4.
· Call
· Back
· More
· Edit
· Delete
45
Make a call to the stored number.
Go back to the directory listing.
If the contact is one of your personal directory entries, the More soft key will be present to allow you to access the options below. It is also present for external directory entries if you are a system administrator (either of t he first two extensions on the system).
45
Edit the name and number.
46
Delete the name and number.
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 44
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 45
Contacts: Viewing Contacts Details
5.2 Make a Call from the Directory
You can use any directory contacts to make a call. You can also use the directory in almost any telephone function where you need to select the number for a destination, for example during transfers.
· On a key mode system, to call an internal number, you need to press an Intercom button before selecting the number from the directory.
Access the contacts directory:
1.
Press the CONTACTS key. The directory menu is displayed.
a.
Use the left and right arrow keys to select which type of directory entries you want displayed.
b.
· All All directory entries.
· Personal Your personal speed dials.
· External The system speed dials.
· Users The names and numbers of other users on the telephone system.
· Groups The names and numbers of hunt groups on the telephone system.
Either press the List soft key to display all the directory entries or start dialing the name to display only
c.
matching entries.
Use the up and down arrow keys to scroll through the matching entries. To return to the start to match a
d.
different directory selection, press the Clear soft key.
When the required entry is displayed, press Call.
2.
Continue as for a normally dialed call.
3.
5.3 Editing a Contact
You can edit the contacts in your own personal directory.
Access your personal directory contacts:
1.
Press the CONTACTS key. The directory menu is displayed.
a.
Use the left and right arrow keys to select your Personal directory. The first two extensions on the system
b.
can also add, edit and delete entries from the External directory.
Either press the List soft key to display all the directory entries or start dialing the name to display only
c.
matching entries.
Use the up and down arrow keys to scroll through the matching entries. To return to the start to match a
d.
different directory selection, press the Clear soft key.
Locate the required entry.
2.
Press the Details soft key.
3.
Press the More soft key and then the Edit soft key.
4.
· The menu now allows editing of the name and number.
· Use the up and down arrow keys to switch between number and name entry.
· When the name has been entered as required, press the OK soft key.
· When the number has been entered as required, press the Save soft key.
· To exit without making any changes, press the Cancel soft key.
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 45
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 46
5.4 Adding a New Contact
So long as the telephone system capacity has not been reached, you can add up to 100 personal directory entries.
Access your personal directory contacts:
1.
Press the CONTACTS key. The directory menu is displayed.
a.
Use the left and right arrow keys to select your Personal directory. The first two extensions on the system
b.
can also add, edit and delete entries from the External directory.
Press the New soft key.
2.
· The menu now allows editing of the name and number.
· Use the up and down arrow keys to switch between number and name entry.
· When the name has been entered as required, press the OK soft key.
· When the number has been entered as required, press the Save soft key.
· To exit without making any changes, press the Cancel soft key.
5.4.1 Add a Contact from the Call Log
You can add a name and number shown in your call log to your personal speed dials. You can only do this if there is space in your allowed 20 personal speed dials.
Access the call log.
1.
Press the CALL LOG or HISTORY button.
a.
The display will change to show your call log records. The caller's name is shown if known, otherwise the
b.
number.
Use the up and down arrow keys to scroll through the records.
c.
Press the Details soft key. The individual details of the currently selected call record are displayed.
2.
Press the +Contact soft key.
3.
Use the up and down arrow keys to switch between the name and number details for the new contact.
4.
Using the telephone keypad and the Bksp soft key you can edit the name and the number. When editing the
5. number, use the Pause soft key to enter a comma (,) for a 1 second pause in the number dialing.
When the name and number are set as required, press the Save soft key. To return without saving the name and
6. number, press the Cancel soft key.
5.5 Deleting a Contact
You can delete a personal speed dial from your contacts.
Access your personal directory contacts:
1.
Press the CONTACTS key. The directory menu is displayed.
a.
Use the left and right arrow keys to select your Personal directory. The first two extensions on the system
b.
can also add, edit and delete entries from the External directory.
Either press the List soft key to display all the directory entries or start dialing the name to display only
c.
matching entries.
Use the up and down arrow keys to scroll through the matching entries. To return to the start to match a
d.
different directory selection, press the Clear soft key.
Locate the required entry.
2.
Press the Details soft key.
3.
Press the More soft key and then the Delete soft key.
4.
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 46
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 47
Chapter 6.
Call Log
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 47
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 48
6. Call Log

This menu is accessed by pressing the CALL LOG or HISTORY key.

· Making a Call
· Viewing Call Details
· Deleting a Record
· Deleting All Records
· Add a Record to Your Contacts
6.1 Using the Call Log
Access the call log.
1.
Press the CALL LOG or HISTORY button.
a.
The display will change to show your call log records. The caller's name is shown if known, otherwise the
b.
number.
Use the up and down arrow keys to scroll through the records.
c.
Pressing OK will make a call to the number stored with the currently displayed record.
2.
You can use the functions listed at the bottom of the display by pressing the soft key below the function name.
3.
· Call Make a call to the number stored in the currently displayed call log record.
· Details Display more details about the current call log record. You can then also add the caller details to your personal
directory if required.
· More Switch between the different sets of available soft key functions.
· Delete Deletes the current displayed record.
· Del All Delete all the call log records, not just the current types of records being shown.
To exit the call log, press the PHONE/EXIT button.
4.
48
49
50
50
50
48
49
50
50
50
6.2 Making a Call from the Call Log
You can use the call log to make calls to the number included in the currently selected call record.
Access the call log.
1.
Press the CALL LOG or HISTORY button.
a.
The display will change to show your call log records. The caller's name is shown if known, otherwise the
b.
number.
Use the up and down arrow keys to scroll through the records.
c.
Press the Call soft key or OK to call the number displayed in the call record.
2.
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 48
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 49
Call Log: Making a Call from the Call Log
6.3 Viewing Call Details
You can view additional details about the currently shown call.
Access the call log.
1.
Press the CALL LOG or HISTORY button.
a.
The display will change to show your call log records. The caller's name is shown if known, otherwise the
b.
number.
Use the up and down arrow keys to scroll through the records.
c.
Press the Details soft key. The individual details of the currently selected call record are displayed.
2.
Use the up and down arrow keys to scroll through the details. The possible values are:
3.
· Time The time of the call.
· Ring Time For missed calls, the duration of ringing is included in the call details.
· Duration The length of the call.
· Name The name of the caller if known.
· Number The number of the caller if available.
· Reason The type of call record, ie. Answered, Outgoing or Missed. For missed calls, the reason may be indicated, for example:
· Missed: Lost - Indicates a call where the caller hung up before they could be answered.
· Missed: Voicemail - Indicates a call where the caller was redirected to voicemail.
· Count
How many time a call of the same type, name and number has occurred. Only the details of the most recent call are kept in your call log. However, the count will indicate if the caller has rung or has been rung several times.
While you are in the details of a call record, the soft key functions available are:
4.
· Call Call the number shown in the call record. You can also do this by pressing the OK button.
· +Contact Add the name and number to your personal directory. You can edit the details before they are added.
· Back Go back to the normal call screen to select another call record.
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 49
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 50
6.4 Deleting a Record
You can delete the currently displayed call record.
Access the call log.
1.
Press the CALL LOG or HISTORY button.
a.
The display will change to show your call log records. The caller's name is shown if known, otherwise the
b.
number.
Use the up and down arrow keys to scroll through the records.
c.
Press the More soft key.
2.
Press the Delete soft key to delete the currently displayed call log record.
3.
6.5 Deleting All Records
You can delete all call records from your call log.
Access the call log.
1.
Press the CALL LOG or HISTORY button.
a.
The display will change to show your call log records. The caller's name is shown if known, otherwise the
b.
number.
Use the up and down arrow keys to scroll through the records.
c.
Press the More soft key.
2.
Press the Del All soft key to delete all your call log records.
3.
6.6 Adding a Record to Your Contacts
You can add a name and number shown in your call log to your personal speed dials. You can only do this if there is space in your allowed 20 personal speed dials.
Access the call log.
1.
Press the CALL LOG or HISTORY button.
a.
The display will change to show your call log records. The caller's name is shown if known, otherwise the
b.
number.
Use the up and down arrow keys to scroll through the records.
c.
Press the Details soft key. The individual details of the currently selected call record are displayed.
2.
Press the +Contact soft key.
3.
Use the up and down arrow keys to switch between the name and number details for the new contact.
4.
Using the telephone keypad and the Bksp soft key you can edit the name and the number. When editing the
5. number, use the Pause soft key to enter a comma (,) for a 1 second pause in the number dialing.
When the name and number are set as required, press the Save soft key. To return without saving the name and
6. number, press the Cancel soft key.
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 50
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 51
Chapter 7.
Button Programming
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 51
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 52
7. Button Programming
1
1.,@2abc23def34ghi45jkl56mno6
7
pqrs7
8
tuv8
9
wxyz9**0Space 0##
You can assign functions to the programmable buttons on your phone. However, you cannot override any Intercom, Call Appearance or Line Appearance buttons assigned by the system and your system maintainer.
7.1 Programming a Button
Use the following process to set or change the function of a button.
· You cannot override any Intercom, Call Appearance or Line Appearance buttons assigned by the system and your system maintainer.
· Some functions are unique, ie. if already assigned to a button, assigning the function to another button will automatically clear the setting from the existing button.
Press the Admin soft key on the display.
1.
· During a call, press the PHONE button to display the Admin soft key option. If you access phone
administration during a call, only the SPEAKER, MUTE and HEADSET buttons still affect the connected call.
Use the up or down arrow buttons to scroll to Telephone Programming. Press Select.
2.
Press the programmable button you want to change. Alternatively:
3.

· Use the up or down arrows to scroll to Button Programming. Press Select.

· At the Button: prompt press the button to edit or enter from the button number.
The current setting of that button is displayed.
4.
· To remove the function, press Clear.
· To change the function, press Program.
· Use the up and down arrow buttons to scroll through the menu options and select the required button
function .
You can add a text label to buttons which have a feature assigned. The label will replace the default label shown
5. otherwise.
Press Label.
a.
Enter a label for the button using the controls and when complete press Save.
b.
54
· Enter a character by pressing the indicated button until that character is displayed. Accented versions of the characters are also shown. If you pause more than 1 second after press a button, the cursor will move onto the next space.
· The first character and the first character after a space are automatically capitalized.
· Use the left and right arrows keys to move the cursor. Press Bksp to delete the character before the
cursor.
· Exit phone administration by pressing the PHONE button. Alternatively use the Back button to move to another menu.
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 52
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 53
Button Programming: Programming a Button
1
1.,@2abc23def34ghi45jkl56mno6
7
pqrs7
8
tuv8
9
wxyz9**0Space 0##
7.2 Changing a Button Label
The default text label shown for a button depends on the function assigned to that button. You can override this by applying your own text label.
Press the Admin soft key on the display.
1.
· During a call, press the PHONE button to display the Admin soft key option. If you access phone
administration during a call, only the SPEAKER, MUTE and HEADSET buttons still affect the connected call.
Use the up or down arrow buttons to scroll to Telephone Programming. Press Select.
2.
Press the programmable button you want to change. Alternatively:
3.
· Use the up or down arrows to scroll to Button Programming. Press Select.
· At the Button: prompt press the button to edit or enter from the button number.
The current setting of that button is displayed.
4.
Press Label.
a.
Change the label for the button using the controls and when complete press Save.
b.
· Enter a character by pressing the indicated button until that character is displayed. Accented versions of the characters are also shown. If you pause more than 1 second after press a button, the cursor will move onto the next space.
· The first character and the first character after a space are automatically capitalized.
· Use the left and right arrows keys to move the cursor. Press Bksp to delete the character before the
cursor.
· Exit phone administration by pressing the PHONE button. Alternatively use the Back button to move to another menu.
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 53
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 54
7.3 Button Functions
Function
Description
Absent Message
This function allows you to set or clear an absent message for display on you phone. When set, the absent message is also displayed on other extensions when they call the user.
Account Code Entry
This function allows you to enter an account code prior to making a call or during a call.
Active Line Pickup
This function allows you to answer a call on a particular line. It can be used if the call is ringing, held or already answered by another extension.
Auto Dial Intercom
This function allows you to make a call to another specified extension. The button lamp will also indicate when that other extension is in use.
Auto Dial Other
This function allows you to make a call using a number stored with the button. The number can be an internal number, an external number, an account code or any other number. The button can then be used when a number of that type needs to be dialed.
Call Coverage
This function allows you to switch call coverage on or off. When on, any calls to you that ring unanswered also start ringing at your call coverage extension.
Caller ID Log
This function allows you to view the phone system's call log of all caller IDs of calls received by the system. To use this you must be one of the three extensions configured for call ID logging by your system administrator.
Call Forwarding
This function allows you to redirect all your calls to another number. If the system administrator has configured your for Remote Call Forwarding, you can forward calls externally by specifying a personal speed dial as the destination.
Call Pickup
This function allows you to pickup a call alerting at a specified extension. Separate buttons can be created for each extension for which call pickup is required.
Call Screening
This function allows you to switch call screening on or off. When on, if your phone is idle, when a call rings it and then goes to voicemail you will hear the caller through the phone's handsfree speaker. You can choose to ignore the call (press Ignore on the display) or to answer it (press
Answer on the display). This button function can only be set by your system administrator.
Caller ID Inspect
This function allows you to see the caller ID of a call on another line without interrupting the current call to which you are connected.
Caller ID Name
This function allows you to swap the display of caller ID name and number information on the phone.
Calling Group
This function allows you to call or page the calling group represented by the button.
Conference Drop
This function allows you to select and drop a call from a conference.
Contact Closure
This function you to operate the system's contact closure 1 or 2 connection. To use this you must be a member of the system's contact closure group.
Do Not Disturb
This function allows you to switch do not disturb on or off.
Hot Dial
This function allows you to dial a stored number without first going off hook or pressing the
SPEAKER button.
Hunt Group
This function allows you to call or page the hunt group represented by the button.
Idle Line Pickup
This function allows the user to seize a line if that line is idle. This allows the user to access line for which they do not have a line appearance button on their extension.
Last Number Redial
This function allows you to redial the last external number dialed.
Message Alert Notification
This function allows you to see the current state of other user's message waiting lamps. It is used in conjunction with other users for which you have Auto Dial - Intercom buttons.
Night Service
A night service button is used to switch night service on/off. It can only be used on the first extension in the system.
Pickup Group
This function allows you to answer a call being presented to any extension that is a member of the pickup group (1 to 4) configured for the button.
You can assign the following functions to programmable buttons on your phone.
52
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 54
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 55
Button Programming: Button Functions
Privacy
This function allows you to turn privacy on or off. When on, other extensions are not able to bridge into your calls.
Recall
This function allows you to send a recall or hook flash signal.
Saved Number Redial
This function allows you to save the number dialed during a call and to redial that number when idle. This can be used when the number dialed does not answer.
Station Lock
This function allows you to lock and unlock your extension from being used to make calls. When selected, you are prompted to enter a four digit code after which the extension is locked. If the extension is already locked, use of this function prompts for reentry of the four digit code to unlock the extension.
Station Unlock
This function can only be used by the first two extensions in the system. It allows the user to unlock any extension without needing to know the code that was used to lock that extension.
VMS Cover
This function allows the you to switch use of voicemail coverage for your extension on or off.
Voice Mailbox Transfer
This function allows you to transfer your current call to another extension's mailbox. Your current call is put on hold and you enter the target extension number to indicate the mailbox required.
Wake Up Service
A Wake Up Service button can be assigned for the first extension on the system. Using this button, the extension user can set wake up calls within the next 24-hours period for any other extension.
Function Status Indication
For some functions, for example those that can be on or off, the icon or LED in the programmable button will indicate the current status of the function.
To activate and deactivate one of the following features using a programmable feature button,press the button and follow the onscreen prompts. During feature activation and deactivation, the status LED on the associated programmable feature button does not reflect the current state of the feature. However, upon exiting the feature activation/deactivation screen, the new state of the feature is shown by the programmable button's status LED.
· Absent Message
· Account Code Entry
· Call Log
· Wake Up Service Button
· Station Lock
· Station Unlock
· Night Service (when a system password has been administered)
· Caller ID Inspect
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 55
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 56
Page 57
Chapter 8.
Phone Settings
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 57
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 58
8. Phone Settings
1
1.,@2abc23def34ghi45jkl56mno6
7
pqrs7
8
tuv8
9
wxyz9**0Space 0##
8.1 Naming Your Extension
You can assign a name to your extension, up to 20 characters long. The name is then displayed on the phone and also on other extensions when you make or receive calls.
To change your extension name
Press the Admin soft key on the display.
1.
· During a call, press the PHONE button to display the Admin soft key option. If you access phone
administration during a call, only the SPEAKER, MUTE and HEADSET buttons still affect the connected call.
Use the up or down arrow buttons to scroll to Telephone Programming. Press Select.
2.
Use the up or down arrow buttons to scroll the display to Extension Name. When displayed, press Select.
3.
The current setting is displayed. To remove the current name, press Clear.
4.
To enter a new name, press Enter and dial the characters using the dial pad buttons. When finished press OK.
5.
· Enter a character by pressing the indicated button until that character is displayed. Accented versions of the characters are also shown. If you pause more than 1 second after press a button, the cursor will move onto the next space.
· The first character and the first character after a space are automatically capitalized.
· Use the left and right arrows keys to move the cursor. Press Bksp to delete the character before the
cursor.
· Do not use punctuation characters such as #, ?, /, -, _ and , in the name. Start the name with an alphabetic character. Note that the name is case sensitive and must be unique. Non-English languages do not offer accented characters.
· Exit phone administration by pressing the PHONE button. Alternatively use the Back button to move to another menu.
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 58
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 59
Phone Settings: Naming Your Extension
8.2 Visual Alerting
The message waiting lamp at the top-right corner of the phone can also be used to indicate when you have a call alerting your phone. The lamp is flashed to indicate a call waiting to be answered.
Press the MENU button.
1.
Use the up and down arrow keys to locate the option Call Settings.... Press the Select soft key.
2.

Use the up and down arrow keys to locate the option Visual Alerting.

3.
Use the left and right arrow keys or press the On/Off soft key to change the setting.
4.
When completed, press the Done soft key.
5.
Press the Exit soft key to exit the menus.
6.
8.3 Audible Alerting
The phone's audible ringer can be switched off. This only affects the ring and does not affect the visual alerting .
Press the MENU button.
1.
Use the up and down arrow keys to locate the option Call Settings....
2.
Press the Select soft key.
3.

Use the up and down arrow keys to locate the option Audible Alerting.

4.
Use the left and right arrow keys or press the On/Off soft key to change the setting.
5.
When completed, press the Done soft key.
6.
Press the Exit soft key to exit the menus.
7.
59
8.4 Ringer Sound
You can adjust the sound of the ring used by the phone.
Press the MENU button.
1.
Use the up and down arrow keys to locate Screen/Sounds or Screen & Sound Options. Press the Select
2.
soft key.
Use the up and down arrow keys to locate the option Personalized Ringing. Press the Select soft key.
3.
· Use the up and down arrow keys to scroll through the different available ring patterns.
· Press the Play soft key to repeat the currently display ring pattern.
· To make the currently displayed ring pattern the selected ring pattern for the phone press the Save soft key.
· To leave the menu without making any changes press the Cancel soft key.
When completed, press the Done soft key.
4.
Press the Exit soft key to exit the menus.
5.
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 59
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 60
8.5 Ringer Volume
When the phone is not on any calls, you can adjust the volume used for the ringer.
With the phone idle, use the up arrow and down arrow keys to change the volume.
1.
8.6 Display Brightness
Press the MENU button.
1.
Use the up and down arrow keys to locate Screen/Sounds or Screen & Sound Options. Press the Select
2.
soft key.
Use the up and down arrow keys to locate Brightness. Press the Select soft key.
3.
Use the up and down arrow keys to adjust the brightness as required.
4.
When completed, press the Done soft key.
5.
Press the Exit soft key to exit the menus.
6.
8.7 Display Contrast
Press the MENU button.
1.
Use the up and down arrow keys to locate Screen/Sounds or Screen & Sound Options. Press the Select
2.
soft key.
Use the up and down arrow keys to locate the option Contrast. Press the Select soft key.
3.
Use the left and right arrow keys to adjust the brightness as required.
4.
When completed, press the Done soft key.
5.
Press the Exit soft key to exit the menus.
6.
8.8 Display Language
The system administrator can configure which language your extension uses. Though the phone's menu you can change that setting.
IP Office Basic Edition - IP Office Basic Edition - Quick Mode supports a number of languages. The phone menu may display other languages also supported by the phone. If one of these other languages is selected, the languages displayed on the phone menu may be a mix of that language and English.
Press the MENU button.
1.
Use the up and down arrow keys to locate the option Advanced. Press the Select soft key.
2.
Use the up and down arrow keys to locate the option Language. Press the Select soft key.
3.
Use the up and down arrow keys scroll through the different languages available.
4.
To select the language currently displayed, press the Select soft key or OK.
5.
When completed, press the Done soft key.
6.
Press the Exit soft key to exit the menus.
7.
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 60
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 61
Phone Settings: Display Language
8.9 Error Tones
Press the MENU button.
1.
Use the up and down arrow keys to locate Screen/Sounds or Screen & Sound Options. Press the Select
2.
soft key.
Use the up and down arrow keys to locate the option Error Tone.
3.
Use the left and right arrow keys or press the On/Off soft key to change the setting.
4.
When completed, press the Done soft key.
5.
Press the Exit soft key to exit the menus.
6.
8.10 Button Clicks
While using the phone menus, the phone can provide a key press confirmation click sound. This can be turned off if it is annoying.
Press the MENU button.
1.
Use the up and down arrow keys to locate Screen/Sounds or Screen & Sound Options. Press the Select
2.
soft key.

Use the up and down arrow keys to locate the option Button Clicks.

3.
Use the left and right arrow keys or press the On/Off soft key to change the setting.
4.
When completed, press the Done soft key.
5.
Press the Exit soft key to exit the menus.
6.
8.11 Default Handsfree Audio Path
By default, when you make a call or answer a call without lifting the handset, the audio is played through the phone's speaker while you speak via the phone's microphone.
If you have a headset attached, you can change the phone's behavior so the audio is played through the headset by default rather than the speaker.
Press the MENU button.
1.
Use the up and down arrow keys to locate the option Call Settings.... Press the Select soft key.
2.
Use the up and down arrow keys to locate the option Audio Path.
3.
Use the left and right arrow keys or press the Change soft key to change the setting.
4.
When completed, press the Done soft key.
5.
Press the Exit soft key to exit the menus.
6.
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 61
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 62
8.12 The Admin Menu
The Admin option is used to access a series of menus for phone based administration.
Press the Admin soft key on the display.
1.
· During a call, press the PHONE button to display the Admin soft key option. If you access phone
administration during a call, only the SPEAKER, MUTE and HEADSET buttons still affect the connected call.
Use the up or down arrow buttons to scroll to Telephone Programming. Press Select.
2.
· For the first two extensions on the system, a range of options are selectable. The use of those options is covered by the IP Office Basic Edition - Quick Mode Phone Based Administration manual.
Use the up and down arrow buttons to scroll through the menu options.
3.
· Button Programming This menu allows you to assign functions to the programmable buttons on your phone. You cannot override any Intercom, Call Appearance or Line Appearance buttons assigned by the system and your system maintainer.
· DND Exceptions Set numbers with can still call you even when you have do not disturb on.
· Extension Name Set your extension name. This is shown on your phone and on others when they call you or are called by you.
· Personal Speed Dial Create and edit your personal speed dials.
· System Speed Dial This option is only shown on the first two extensions in the system. It allows those extension users to create and edit system speed dials for use by all users.
52
36
58
20
19
· Exit phone administration by pressing the PHONE button. Alternatively use the Back button to move to another menu.
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 62
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 63
Phone Settings: The Admin Menu
8.13 The A MENU
The MENU key is used to access a range of phone settings. These are mainly settings held by the phone, not the phone system.
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 63
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 64
8.14 A-Menu Auto Exit
The Show Phone Screen option only applies to the A-menu screens accessed when you press the key. If the option is on, if you receive a call while in the A-menu, the phone will automatically exit the menus and display the call details.
Press the MENU button.
1.
Use the up and down arrow keys to locate the option Call Settings.... Press the Select soft key.
2.
Use the up and down arrow keys to locate the option Show Phone Screen.
3.
Use the left and right arrow keys or press the On/Off soft key to change the setting.
4.
When completed, press the Done soft key.
5.
Press the Exit soft key to exit the menus.
6.
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 64
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 65
Index
A
Absent Text Message 30 Account Code 35 Add
Contact 46, 50 Alert Notification 54 All
Call Log 46, 48, 49, 50
Contacts 44, 45 Answer a Call 17 Answered 46, 48, 49, 50 At home 30 At lunch until 30 Audible Alerting 59 Audio Path 61 Auto Dial 21 Away from desk 30
B
Back soon 30 Back tomorrow 30 Be right back 30 Bridge 27 Button
Call Screening 54
Message Alert Notification 54
C
Call
Bridge 27
Coverage 32
Forward 31
from Call Log 48
from Contacts 45
Ignore 17
Join 27
Park 23
Pickup 17
To VM 17 CALL LOG 46, 48, 49, 50
Call from 48
Details 49
Menu 48 Call Screening 54 Call Settings
Audible alerting on/off 59
Audio Path 61
Visual alerting on/off 59 Call Transfer - Supervised 24 Call Transfer - Unsupervised 24 Callback 14 Caller
Details 49 Caller volume 22 Code
Account 35
Lock 34 Conference
Hold 25
Start 25 Contact
Add 46, 50
Edit 45, 46 CONTACTS 44, 45, 46
Make call 45
Index
Count 49 Coverage
Call 32 Voicemail 41
D
Details
Call Log 49
Directory
Add 46, 50 Edit 45, 46
Make call 45 Do Not Disturb 30, 36 Don't disturb until 30
E
Edit
Contact 45, 46 Exceptions 37 Extension
Name 58 External 44, 45
F
Forward 31
G
Group
Call log 48
Missed 48 Groups 44, 45
H
Handset volume 22 Handsfree 26 Hold
Conference 25 Hold a Call 23 Hunt group
Call log 48
Missed 48
I
Ignore 17
J
Joining a Call 27
L
Lamp 59 Lock 34
M
Make call
from Call Log 48
from Contacts 45 Meeting until 30 Menu
Call log 48
Contacts 44 Message Alert Notification 54 Message waiting lamp 59 Missed 46, 48, 49, 50 Missed calls
Hunt group calls 48 More 48
N
Name 58 New
Contact 46, 50 Notification 54
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 65
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 66
O
On holiday until 30 On vacation 30 Out to lunch 30 Outgoing 46, 48, 49, 50
P
Parking Calls 23 Persoanl Speed Dial 20 Personal 44, 45 Please call 30
R
Reason 49 Ring Again 14 Ring Back 14 Ring Time 49 Ringer
Audible alerting on/off 59
Ringer volume 22
S
Screening 54 Speaker volume 22 Speakerphone 26 Speed Dial
Personal 20
System 19 Supervised Call Transfer 24 System Speed Dial 19
T
To VM 17 Transfer
To Voicemail 24 Transfer a Call 24
U
Unlock 34 Unsupervised Call Transfer 24 Users 44, 45
V
Visual Alerting 59 Voicemail
Coverage 41
Transfer 24 Volume 22
W
Wake Up Service 54 With Cust. until 30 With visitors until. 30
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 66
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 67
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 67
- Issue 6b (23 November 2011)IP Office Basic Edition
Page 68
Performance figures and data quoted in this document are typical, and must be specifically confirmed in writing by Avaya before they become applicable to any
particular order or contract. The company reserves the right to make alterations
or amendments to the detailed specifications at its discretion. The publication of
information in this document does not imply freedom from patent or other
protective rights of Avaya or others.
All trademarks identified by the ® or ™ are registered trademarks or trademarks,
respectively, of Avaya Inc. All other trademarks are the property of their
respective owners.
This document contains proprietary information of Avaya and is not to be
disclosed or used except in accordance with applicable agreements.
© 2011 Avaya Inc. All rights reserved.
IP Office Basic Edition - Quick Mode 9500 Series Phone User Guide Page 68
- Issue 6b (23 November 2011)IP Office Basic Edition
Loading...