Avaya 10-Watt User Manual

Telephone Paging Amplifier 10-Watt Model
Installation and Use Manual
© 2002 Bogen Communications, Inc. All rights reserved. 54-2021-01R2 0208 LU10WAMP: PEC Code: 5328-010
COM Code: 408186062
Select Code: 701-000-108
Notice
Every effort was made to ensure that the information in this guide was complete and accurate at the time of printing. However, information is subject to change.
Important Safety Information
Always follow these basic safety precautions when installing and using the unit:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the product.
3. DO NOT place the product in a separate enclosure or cabinet, unless proper ventilation is provided.
4. Never spill liquid on the product. Doing so may result in serious damage to the components.
5. Repair or service must be performed by a factory authorized repair facility.
6. The product is provided with a UL-CSA approved, 3-wire ground type plug.This is a safety feature. DO NOT defeat the safety purpose of the grounding type plug. DO NOT staple or otherwise attach the AC power supply cord to building surfaces.
7. DO NOT use the product near water or in a wet or damp place (such as a wet basement).
8. DO NOT use extension cords.The product must be installed within 6 feet of a grounded outlet receptacle.
9. DO NOT install telephone wiring during a lightning storm.
10. DO NOT install telephone jacks in a wet location unless the jack is specifically designed for wet locations.
11. Never touch uninsulated wires or terminals, unless the line has been disconnected at the paging or controller interface.
12. Use caution when installing or modifying paging or control lines.
Support Information
Paging systems integrated with small phone systems such as Merlin Legend and Partner are supported by the National Service Assistance Center (NSAC). The main number for the NSAC is 800-628-2888. Paging systems integrated with large switches such as the DEFINITY G3 are supported by the Technical Service Center (TSC). The main number for the TSC is 800-242-2121.
Domestic and International Approvals
UL and CSA Listed.
© 2002 Bogen Communications, Inc. All Rights Reserved. Printed in Korea.
Page 2 of 8
Contents
Page
INTRODUCTION..........................................................................................................................4
PACKAGE CONTENTS..............................................................................................................4
INSTALLATION..............................................................................................................................5
Mounting ............................................................................................................................5
WIRING CONNECTIONS........................................................................................................5
Input Wiring......................................................................................................................5
TEL Input and Control Pair ............................................................................................................5
Tel Input to Universal Coupler ......................................................................................................6
Music Input..........................................................................................................................................6
Night Bell Connection ......................................................................................................................6
Output Wiring ................................................................................................................7
Speaker Connection ..........................................................................................................................7
OPERATION ....................................................................................................................................8
Indicator ............................................................................................................................8
Controls ..............................................................................................................................8
Page Volume ........................................................................................................................................8
Music Volume ......................................................................................................................................8
Night Bell..............................................................................................................................................8
Lo-Cut Switch ......................................................................................................................................8
Tone ......................................................................................................................................................8
Page 3 of 8
Introduction
This document describes the Avaya 10-watt Telephone Paging Amplifier.This is a full­featured, wall-mounted amplifier that provides inputs for dry loop 600-ohm telephone page signal and background music source. A set of control inputs allow an external contact closure to mute background music and open the telephone page channel. Background music mute level during page is adjustable and the music slowly fades back in after the page is completed. An automatic level control system limits the output level of the telephone page channel so that differences in the volume of the paging party's voice will be less noticeable. A tone control is provided for optimizing tonal balance for the specific installation. This amplifier includes a built-in night bell that can be triggered by an external contact closure. The night bell mutes the background music, but not pages.
Package Contents
* Telephone Paging Amplifier unit * 2 mounting screws * Installation and Use Manual
Before You Start Review the contents of the box.Read through this entire manual to understand how
to install and operate this product.
NOTE: Use minimum 22 AWG shielded, twisted pair wire for your speaker runs.
Telephone Paging Amplifier
Page 4 of 8
Figure 1: Telephone Paging Amplifier
Installation
The amplifier is designed for wall mount applications. The 10-watt amplifier weighs 4 lb.
NO
TE: The amplifier will produce heat during operation which will rise and may
cause problems for temperature-sensitive equipment mounted above it. Mount the amplifier near the top of the backboard so that no other equipment will be above it. If this is not possible, then allow at least 12" between the top of the amplifier and the bottom of any equipment positioned above it. Also allow at least 4" between the bottom of the amplifier and any equipment below it to allow for adequate air circulation. In addition, because the unit itself gets hot, avoid touching it during operation.
Wall Mounting To wall mount this unit, use the two 5/8” pan head screws with nylon washers
provided.The screws should protrude approximately ¼" from the surface of the backboard. Lift the amplifier and place it over the two screws using the keyhole slots in the flanges at the sides of the amplifier. The screws should engage the keyhole slots. Once in the keyhole slots, tighten the screws to secure the amplifier.
Mounting
Page 5 of 8
Wiring Connections
IMPORTANT: Before making any connections or wiring changes to the amplifier or any equipment connected to the amplifier, make sure that the amplifier is NOT plugged into an AC outlet.
NO
TE: The amplifier does not have a power switch, so it must be unplugged in
order to turn the power off.
All signal input and control wiring is made to the terminal strip on the front of the unit.
TEL Input and Control Pair The telephone input is a 600-ohm, dry loop, balanced input available at the T and R
terminals. It is controlled by a dry contact closure that is made between the control terminals labeled TEL CONT and GND. Shorting these terminals together will mute the background music input and open the Tel page channel (see Figure 2).
NO
TE: In instances where the amplifier is to be placed permanently in the Tel page
mode, a wire jumper must be installed between the TEL CONT and GND terminals.
Input Wiring
TEL
CONT
T
NIGHT BELL
R
TEL
GND
MUSIC
IN
BGM IN
PAGING TIMEVOX DELAYTONE VOL.
MIN MAXMIN MAXMIN MAX
Universal Paging Access Module
S5
S5
VOX ENABLE
VOX DISABLE
S3
S4
PREANNOUNCE TONE
S3 S4
CONFIRMATION TONE
48VDC PWR SUPPLY S1,S2
24VDC PWR SUPPLY S1,S2
ONOFFMODE
VOL
BGM
SWITCHES
MODE
(0.1A)
(TRUNK ACCESS ONLY)
POWER SUPPLY
CONTACT CLOSURE A
PAGING OUTPUT
EXT VOX ENABLE
PHONE SYSTEM
-24/48
+24/48
COM
N.O.
PR
PT
-M
+M
R
T
CONTACT CLOSURE B
N.O. COM
PAGE PORT
INPUT
Tel Input to Universal Coupler After properly connecting your Universal Coupler (909) to your Auxiliary Trunk
port, set your switches as follows: C1/C2 to C2; Rocker Switch 3 closed; and all others open. Coming out of the J2 Jack of the Coupler, connect the blue/white pair to the amplifier’s T and R terminals.
Music Input A pair of terminals are provided for the connection of a background music source.
Use a pair of wires (not included) to make this connection. This is a mono input and requires that the output of stereo sources be converted to mono by using a Y­adapter (not included). Use a LUWMT1A (COM Code: 405891680) to balance the music input, if necessary, to reduce hum/noise from a grounded music source.
Night Bell Connection An external contact closure activates the night bell function of the amplifier. When
using an external contact closure, connect the closure pair across the Night Bell terminal and GND. The night ringer follows the cadence of the activating signal.
CAUTION: Do not apply a high voltage (90-105V AC, 20-30Hz) ring signal to the Night Bell terminals. Use a dry contact closure only.
Figure 2: Wiring for TEL Input
Page 6 of 8
Telephone Paging Amplifier
+
_
+
_
70V25V
8
COM
TEL CONT
T
NIGHT BELL
L
U
AMPLIFIER
COMMERCIAL
538C
LISTED
0.5A
60 Hz
120 VAC
MADE IN KOREA
AND RATING
SAME TYPE
BREAKER WITH
REPLACE CIRCUIT
CAUTION:
VOL
NIGHT BELL
R
TEL
GND
MUSIC
IN
70V25V
8
COM
PUSH TO RESET CIRCUIT BREAKER
LO-CUT
PEAK
LEVEL
VOL
PAGE
MUSIC
VOL
TONE
E15903
Page 7 of 8
All output wiring connections are made to the terminal strip located on the left side of the LU10WAMP.
IMPORTANT: Before making any connections or wiring changes to the amplifier or any equipment connected to the amplifier, make sure that the amplifier is NOT plugged into an AC outlet.
NOTE: The amplifier does not have a power switch, so it must be unplugged in order to turn the power off.
Speaker Connection 70-volt speaker connections are made between the 70V and COM terminals on the
output terminal strip (see Figure 3). Use minimum 22 AWG shielded, twisted pair cable. Connect the shield of the cable to the terminal strip.
NO
TE: The amplifier output terminal strip also includes terminals for 8-ohm and
25V speaker connections. These are provided for special applications and are generally not used.
Figure 3: Speaker Connection, Output Wiring
Output Wiring
Enlarged view of Ouput Terminal Strip
to PBX ground
Page 8 of 8
Operation
IMPORTANT: Before plugging the amplifier into an AC outlet, turn all volume controls to their full counterclockwise positions and all other controls to their reference position.
PEAK LEVEL The PEAK LEVEL LED illuminates whenever the speaker output signal level
approaches its maximum level. This indicator is used when setting volume levels. Maximum output level is achieved when the PEAK LEVEL indicator flashes intermittently on loud peaks of the input signal. If the indicator illuminates steadily, the output signal volume is set too high and distortion is occurring. Decrease the volume control for the appropriate input until the indicator flashes only intermittently.
PAGE VOLUME This control adjusts the level of the telephone page output. A reference level setting
position is provided with this control. When set to this position, the output level of the page should be optimally loud without distortion. Further adjustment can be made using the PEAK LEVEL indicator, as described above.
MUSIC VOLUME This control adjusts the level of the background music output. No reference level
setting position is provided. The background music level should be set to an acceptable level without overdriving the system. When adjusting this level, use the PEAK LEVEL indicator, as described above.
NIGHT BELL This control adjusts the level of the night bell tone output. No reference level setting
position is provided. The night bell level should be set to the customer's satisfaction. When adjusting this level, the PEAK LEVEL indicator should be used to ensure that the amplifier signal is not distorted.
LO-CUT SWITCH Set the LO-CUT switch to the LO-CUT position for optimum speech reproduction
and to reduce unnecessary low frequencies.
TONE Use the TONE control to optimize the tonal balance of the amplifier output.
Indicator
Controls
Loading...