Avanti DGR24P3S Instruction manual

ATTENTION:

burner.

FOR YOUR SAFETY:

THIS UNIT HAS BEEN DESIGNED WITH A FLAME SENSOR SYSTEM THAT MONITORS THE COOKTOP BURNERS.

When using the cooktop, press the knob all the way in, turn to ignite the flame and hold for approximately 10 seconds to allow the system to heat to the appropriate temperature and allow the flow of gas to the selected



INSTRUCTION MANUAL

MANUAL DE INSTRUCCIONES

MANUEL D’INSTRUCTIONS



20” WIDE 24” WIDE Model Numbers / Nos. de Modelos: DGR20P3S DGR24P3S Nos de Modèle



GAS RANGE / COCINA DE GAS / FOURNEAU À GAZ

DGR20P3S DGR24P3S

BEFORE USE, PLEASE READ AND FOLLOW ALL SAFETY RULES AND OPERATING INSTRUCTIONS. AND SAVE FOR LOCAL GAS AND ELECTRICAL INSPECTOR’S USE.

Avanti Products has a policy of continuous improvement on its products and reserves the right to change materials and specifications without notice.

Avanti Products LLC

P.O. Box 520604 - Miami, Florida 33152

www.avantiproducts.com



Range Safety

TABLE OF CONTENTS

Important Safe guides

The Anti-tip Bracket

Help Us Help You …

Parts and Features

Before Using Your Gas Range

Important Precautions and Recommendations

How to use the top burners

How to use the Gas oven / Rotisserie (DGR24P3S - ONLY)

Oven light

Care and Maintenance

Troubleshooting Guide

Wiring Diagram

Service for Your Appliance

Your Avanti Products Warranty

Instrucciones en Español

Instructions en Français

Registration Information and Registration Card

7 - 8

10 - 13

14 - 15

15 - 19

20 - 23

24 - 25

27 - 47

48 - 73

Last



RANGE SAFETY

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

All safety messages will alert you what the potential hazard is, tell you how to reduce the chance of injury, and let you know what can happen if the instructions are not followed.

 This product must be installed by a licensed plumber or gas fitter.  When using ball-type gas shut-off valves, they shall be the T-handle type. 

A flexible gas connector, when used, must not exceed 3 feet in length.

Your safety and the safety of others are very important.

This is the Safety Alert Symbol. This symbol alerts you to potential hazards that can kill or injure you and others.

All safety messages will follow the Safety Alert Symbol and either the words “DANGER”, “WARNING” or “CAUTION”. These words mean:

Danger means that failure to heed this safety statement may result in severe personal injury or death.

Warning means that failure to heed this safety statement may result in extensive product damage, serious personal injury, or death.

Caution means that failure to heed this safety statement may result in minor or moderate personal injury, or property or equipment damage.

IN THE COMMONWEALTH OF MASSACHUSETTS

BEFORE YOU BEGIN!

Installation of this range must conform with all local codes, or in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1 / NFPA.54, latest edition. In Canada, installation code, CAN/CGA-B149.1 or the current Propane installation code, CAN/CGAB149.2, and with local codes where applicable.

BEFORE INSTALLATION

DO NOT use an air curtain or other overhead range hood, which operates by blowing a downward

airflow onto a range, in conjunction with a gas range unless the hood and range have been designed and tested and listed by an independent laboratory in accordance with the Standard for Domestic Gas Ranges, ANSI Z21.1• CSA 1.1 for combination use. The installation instructions for both the gas range and air curtain range hood shall include statements that the air curtain or overhead range hood is permitted to be used in conjunction with a gas range, and that both unit have been designed and tested in accordance with the Standard for Domestic Gas Ranges, ANSI Z21.1 • CSA 1.1 for combination use. Purchaser / Installer should review the installation instructions for each unit to ensure their range is acceptable for use with such ventilation system.

Installation in Manufacturered (Mobile) Homes:

The installation must conform with the Manufactured Home Construction and Safety standard, Title 24 CFR, Part 3280 [formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD (Part 280)} or, when such standard is not applicable, the Standard for Manufactured Home Installations, ANSI/NCSBCS A225.1, or with local codes where applicable.



IMPORTANT SAFE GUIDES

Before the appliance is used, it must be properly positioned and installed as described in this manual, so read the manual carefully. To reduce the risk of fire, electrical shock or injury when using the appliance, follow basic precaution, including the following:

  It is recommended that a separate circuit, serving only your appliance be provided. Use

receptacles that cannot be turned off by a switch or pull chain.

 Never clean appliance parts with flammable fluids. These fumes can create a fire hazard or

explosion. And do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. The fumes can create a fire hazard or explosion.

 Before proceeding with cleaning and maintenance operations, make sure the power line of the

unit is disconnected.

 Unplug the appliance or disconnect power before cleaning or servicing. Failure to do so can result

in electrical shock or death.

 Do not attempt to repair or replace any part of your appliance unless it is specifically

recommended in this manual. All other servicing should be referred to a qualified technician.

WARNING: If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or death.

 This appliance shall not be used for space heating. The surface unit should not be operated

without cookware. This information is based on safety considerations.

 All openings in the wall behind the appliance and in the floor under the appliance shall be sealed.  Keep appliance area clear and free from combustible materials, gasoline, and other flammable

vapors.

 Do not obstruct the flow of ventilation air.  Disconnect the electrical supply to the appliance before servicing.  When removing appliance for cleaning and/or service:

 Disconnect AC power supply.  Carefully remove the range by pulling outward.

CAUTION: Range is heavy. Use care in handling.

 The misuse of oven door (e.g. stepping, sitting, or leaning on them) can result in potential hazards

and /or injuries.

 When installing or removing the range for service, a rolling life jack should be used. Do not push

against any of the edges of the range in an attempt to slide it into or out of the installation. Pushing or pulling a range (rather than using a lift jack) also increases the possibility of bending the leg spindles or the internal coupling connectors.

 It is important for the appliance to be leveled in order to work properly. You may need to make

several adjustments to level it.

 Never allow children to operate, play with or crawl inside the appliance.  Electrical Grounding Instructions - The appliance must be installed and grounded by a qualified

technician in accordance with the National Electrical Code ANSI/NFPA No. 70 (Latest Edition) and local electrical code requirements.



Replacement Parts – Only authorized replacement parts may be used in performing service on the range. Replacement parts are available from factory authorized parts distributors. Contact the nearest Avanti service center in your area.



THE ANTI-TIP BRACKET

The range will not tip during normal use. However, the range can tip if you apply too much force or weight to the open door without the anti-tip bracket fastened down properly.

To reduce the risk of tipping the appliance, the appliance must be secured by properly installed anti-tip devices packed with the appliance.

Range Foot Anti-tip Bracket

WARNING

 ALL RANGES CAN TIP

 INJURY TO PERSON COULD RESULT

 INSTALL ANTI-TIP DEVICE PACKED

WITH RANGE

 SEE INSTALLATION INSTRUCTIONS

Making sure the anti-tip bracket is installed:

 Slide range forward.  Look for the anti-tip bracket securely

attached to floor.

 Slide range back so rear range foot is

under anti-tip bracket.



HELP US HELP YOU...

Read this guide carefully.

It is intended to help you operate and maintain your new Gas Range properly.

Keep it handy to answer your questions. If you don't understand something or you need more assistance, please call:

Avanti Customer Service 800-220-5570

Keep proof of original purchase date (such as your sales slip) with this guide to establish the warranty period.

IF YOU NEED SERVICE

We're proud of our service and want you to be pleased. If for some reason you are not happy with the service you receive, here are some steps to follow for further assistance. FIRST, contact the people who serviced your Gas Range. Explain why you are not pleased. In most cases, this will solve the problem.



Write down the model and serial numbers.

You'll find them on a plate located on the front bottom wall of the Gas Range.

Please write these numbers here:

Date of Purchase

Model Number

Serial Number

Use these numbers in any correspondence or service calls concerning your Gas Range.

If you received a damaged Gas Range, immediately contact the dealer (or builder) that sold you the Gas Range.

Save time and money. Before you call for service, check the Troubleshooting Guide. It lists causes of minor operating problems that you can correct yourself.

NEXT, if you are still not pleased, write all the details, including your telephone number, and

send it to:

Customer Service Avanti Products 10880 NW 30 Street Miami, FL 33172



PARTS & FEATURES

Model: DGR20P3S Model: DGR24P3S



1 Backsplash / Oven Vent



2 Cast Iron Pan Supports 2 Cast Iron Pan Supports



3 Sealed Burners (Total 4) 3 Sealed Burners (Total 4)



4 Control Panel with Digital Clock 4 Control Panel with Digital Clock



5 Oven Door with Handle 5 Oven Door with Handle



6 Storage Drawer with Handle 6 Storage Drawer with Handle



1 Backsplash / Oven Vent



Digital Clock / Timer

DGR20P3S



1 

CONTROL PANEL

Front Left Burner Control Knob

2 Rear Left Burner Control Knob 3 Oven Temperature Control Knob

4 Digital Timer and Clock 5 Lamp / Rotisserie Control Knob 6 Front Right Burner Control Knob 7 Rear Right Burner Control Knob

1 

Front Left Burner Control Knob

2 Rear Left Burner Control Knob 3 Oven Temperature Control Knob

4 Digital Timer and Clock 5 Lamp / Rotisserie Control Knob 6 Front Right Burner Control Knob 7 Rear Right Burner Control Knob

   

MODEL # DGR20P3S

  

MODEL # DGR24P3S



DGR24P3S



COOKTOP

BTU/hr Ratings



20” 24” 1 Auxiliary 2500 2500 2 Right Semi-rapid 4300 4300 3 Left Semi-rapid 4300 4300 4 Rapid 8000 8000

Note:

-The electric gas-lighting device is incorporated into the knobs.

CAUTION: If the burner is accidentally extinguished, turn the gas off at the control knob and wait at least 1 minute before attempting to relight.

CAUTION: Gas appliances produce heat and humidity in the environment in which they are installed. Ensure that the cooking area is well ventilated following national/local codes.

Digital Kitchen Timer

When you first plug in the range or power has returned after 10 hours you will see 12:00 in the display and hear an alarm tone. CLOCK: (APPLIES TO BOTH MODELS)

To set the clock, press the SET button once, the hour will flash.

Model #: DGR20P3S

Digital Display Up (+) Button Down (-) Button Set Button

Back Light ON/OFF Button

Model #: DGR24P3S

Digital Display Up (+) Button Down (-) Button Set Button

Back Light ON/OFF Button

Adjust the hour by pressing the UP or DOWN buttons, when done, press the SET button and repeat the steps for the minutes. To confirm the setting simply wait approximately 5 seconds and the set time will show in the LED display.

COOK TIMER: (APPLIES TO BOTH MODELS).

Press and hold the SET button for approximately 3 seconds. The display will show 00:00. Press the UP or DOWN buttons to choose the desired cook time (1 – 99 minutes, default is 00 minutes). After 5 seconds, the setting will be confirmed and the countdown will begin. The display will return to the CLOCK display mode, to see the countdown press the SET button 3 times. Once the selected time has elapsed, the alarm will sound 15 times or until a button is pressed.

OVEN LIGHT: (Model DGR20P3S – ONLY).

To turn the oven light ON or OFF simply press the OVEN LIGHT / BACKLIGHT BUTTON.

BACKLIGHT: (Knob Indicator Lights – Model DGR20P3S).

To turn the indicator lights behind the control panel knobs ON or OFF press and hold the OVEN LIGHT / BACK LIGHT button for approximately 3 seconds

BACKLIGHT: (Knob Indicator Lights – Model DGR24P3S).

To turn the indicator lights behind the control panel knobs ON or OFF press the OVEN LIGHT / BACK LIGHT button.

Note: Line drawing above may vary from your actual unit.



BEFORE USING YOUR GAS RANGE

WARNING!!

HAVE THIS RANGE INSTALLED BY A QUALIFIED INSTALLER. Improper installation, adjustment, alteration, services, or maintenance can cause injury or property damage. Consult a qualified installer, service agency, or the gas supplier.



Before Using Your Gas Range

√Remove the exterior and interior packing.

√Remove the protective film on steel and aluminum parts √Check to be sure you have all of the parts listed below

● 1 Backsplash

● LP Gas Conversion Packet(injectors for LP gas, 6pcs)

● 1 Anti-tip bracket

● 2 Pan supports

● 2 Oven racks

● 4 Caps and bases in the burner assembly

● 1 Broiler Grid

● 1 Broiler Tray

● 1 Regulator(Pre-installed)

● 5 Screws for Backsplash

● 1 Instruction Manual

● 1 Installation Manual

● 1 Turnspit Kit(DGR24P3S -ONLY)

√ Clean the interior surface with lukewarm water using a soft cloth √ Have the installer show you the location of the range’s gas shut-off valve and how to shut it

off if necessary. √ Have your range installed and properly grounded by a qualified installer in accordance with the installation instructions. √ Do not attempt to repair or replace any part of your range unless it is specifically recommended in this manual. √ Be sure your range is correctly adjusted by a qualified service technician or installer for the type of gas (natural or LP) that is being used. √ Do not remove permanently affixed labels, warnings, or plates from the product. This may void the warranty. √ The installer should leave these instructions with the consumer who should retain for local inspector’s use and for future reference. √ Please observe all local and national codes and ordinances.



IMPORTANT PRECAUTIONS AND RECOMMENDATIONS

This appliance is designed and manufactured solely for the cooking of domestic (household) food and is not suitable for any non-domestic application and therefore CANNOT be used in a commercial environment.

The appliance guarantee will be void if the appliance is used within a non-domestic environment i.e. a semi commercial, commercial or communal environment.

Read the instructions carefully before installing and using the appliance. CAUTION: this appliance must only be installed in a permanently ventilated room in

complianc e with the applic able regulati o n s.

It is advised to follow these instructions:

√

Clean the interior of the oven with a clean cloth soaked in water and detergent (neutral, then dry

carefully).

√

Furnish the interior of the oven by inserting the shelves and tray.

√

Turn the oven on to the maximum temperature to eliminate any possible traces of grease from

the oven burner. The same operation should be followed for the broiler burner.

** NOTE ** This appliance can be used with LP gas and NG gas. It is shipped from the factory adjusted for use with NG (Natural Gas). Conversion orifices are included. Follow the instruction packaged with the orifices for gas conversion.

Natural Gas Orifices

uxiliary

Burner:

0.8 1.0 1.0



SemiRapid Burner:

Rapid Burner:

1.4



Broil Burner:



Oven Burner:

1.24/1.3 1.24/1.4



LPG Orifices

uxiliary

Burner:

SemiRapid Burner:

Rapid Burner:

Broil Burner:

Oven Burner:

0.53 0.68 0.68 0.9 0.8 0.8(0.82)

TTENTION:

YOUR PRODUCT IS PRE-INSTALLED WITH NATURAL GAS INJECTORS AND REGULATOR.

IF YOU ARE USING LP GAS PLEASE REFER TO INSTALLATION INSTRUCTIONS INCLUDED WITH THE CONVERSION KIT.



IMPORTANT PRECAUTIONS AND RECOMMENDATIONS

√ After having unpacked the appliance, check to ensure that it is not damaged and that

the oven door closes correctly. In case of doubt, do not use it and consult your supplier or a professionally qualified technician.

√ Packing elements (i.e. plastic bags, polystyrene foam, nails, packing straps, etc.)

should not be left around within easy reach of children, as these may cause serious injuries.

√ The packaging material is recyclable and is marked with the recycling symbol

√ Do not attempt to modify the technical characteristics of the appliance as this may

cause danger to users.

√ Do not carry out cleaning or maintenance operations on the appliance without having

previously disconnected it from the electric power supply.

√ If you should decide not to use this appliance any longer (or decide to substitute an

older model), before disposing of it, it is recommended that it be made inoperative in an appropriate manner in accordance to health and environmental protection regulations, ensuring in particular that all potentially hazardous parts be made harmless, especially in relation to children who could play with unused appliances.

√ Remove the door before disposal to prevent entrapment..

√ After use, ensure that the knobs are in OFF position.

√ Do not allow children or other unqualified people to use the appliance without your

supervision.

√ During and after use of the range, certain parts will become very hot. Do not touch hot

parts.

√ Keep children away from the range when it is in use

√ Fire risk! Do not store flammable material in the oven or in the bottom drawer.

√ Make sure that electrical cables connecting other appliances in the proximity of the

range cannot come into contact with the hob or become entrapped in the oven door.

√ Do not line the oven walls top and bottom with aluminium foil. Do not place shelves,

pans, baking trays, broil tray or other cooking utensils on the base of the oven chamber.

√ The manufacturer declines all liability for injury to persons or damage to property

caused by incorrect or improper use of the appliance.

√ To avoid any possible hazard, the appliance must be installed by qualified personnel

only. Any repairs by unqualified persons may result in electric shock or short circuit. In order to avoid possible injuries to your body or to the appliance, do not attempt any repairs by yourself. Such work should be carried out by qualified service personnel only.

√ Danger of burns! The oven and cooking accessories may become very hot during

operation. Make sure children are kept out of reach and warn them accordingly. To avoid burns use kitchen clothes and gloves when handling hot parts or utensils.

√ Stand away from the range when opening oven door. Hot air or steam which escapes

can cause burns to hands, face, and/or eyes.

√ Never clean the oven with a high-pressure steam cleaning device, as it may provoke

a short circuit.

√ This appliance is intended for use in your household. Never use the appliance for any

other purpose!





IMPORTANT PRECAUTIONS AND RECOMMENDATIONS FOR USE OF ELECTRICAL APPLIANCES

Use of any electrical appliance implies the necessity to follow a series of fundamental rules. In particular:

✓ Never touch the appliance with wet hands or feet; ✓ Do not operate the appliance barefooted; ✓ Do not allow children or disabled people to use the appliance without your supervision.

The manufacturer cannot be held responsible for any damages caused by improper, incorrect or unreasonable use of the appliance



GENERAL INFORMATION

WARNING!!

1. This appliance shall not be used for space heating. This information is based on safety

considerations.

2. AlI openings in the wall behind the appliance and in the floor under the appliance shall be

sealed.

3. Keep appliance area clear and free from combustible materials, gasoline, and other

flammable vapors.

4. Do not obstruct the flow of combustion and ventilation air.

5. Disconnect the electrical supply to the appliance before servicing.

6. When removing appliance for cleaning and/or service; A. Shut off gas at main supply.

B. Disconnect AC power supply. C. Disconnect gas line to the inlet pipe. D. Carefully remove the range by pulling outward.

CAUTION: Range is heavy; use care in handling.

7. The misuse of oven door (e.g. stepping, sitting, or leaning on them) can result in potential

hazards and/or injuries.

8. When installing or removing the range for service, a rolling lift jack should be used. Do not

push against any of the edges of the range in an attempt to slide it into or out of the installation. Pushing or pulling a range (rather than using a lift jack) also increases the possibility of bending the leg spindles or the internal coupling connectors.

** WHAT TO DO IF YOU SMELL GAS **

•

Do not try to light any appliance.

•

Do not touch any electrical switch.

•

Do not use any phone in your building.

•

Immediately call your gas supplier from a neighbor’s phone Follow the gas supplier instructions.

•

If you cannot reach your gas supplier, call the fire department.



WARNING!!



ELECTRICAL GROUNDING INSTRUCTIONS

FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PROPERLY GROUNDED.

This appliance is equipped with a three-prong grounding plug for your protection against shock hazard and should be plugged directly into a properly grounded socket. Do not cut or remove the grounding prong from the plug.



The gas range must be installed with all electrical connections in accordance with state and local codes. A standard electrical supply (115 V AC only, 60 Hz), properly grounded in accordance with the National Electrical Code and local codes and ordinances is required.

Do not under any circumstances cut or remove the third (gro un d) pro ng fr o m the power plug. Electrical installation should comply with national and local codes.



REPLACEMENT PARTS

Only authorized replacement parts may be used in performing service on the range. Replacement parts are available from factory authorized parts distributors. Contact the nearest AVANTI parts distributor in your area.

CARBON MONOXIDE WARNING:

Carbon Monoxide is a possible danger when using any gas powered appliance.

All gas appliances MUST be installed by a licensed professional who is familiar with the Carbon Monoxide levels appropriate for each appliance.

The American Gas Association publishes CO emissions for appliances and heating equipment through the ANSI Std. Z21.1

The EPA reports that a maximum CO (Carbon Monoxide) level of 9 PPM over a 24 hour period is the residential interior ambient level standard.

( A properly ventilated home will have a normal CO level of less than 5 PPM.)

NON-VENTED GAS COOKING APPLIANCES: In a residential application are normally used for a short period of time. The CO generated during the operation will disperse to the air in the home and be purged to the outside through the normal air exchange.



HOW TO USE THE TOP BURNERS



Control Knobs.

Each of the control knobs for the range is equipped with a ring of dual color LED status indicator lights

BLUE: When the knobs are in the OFF position the indicator lights will be in a bright blue color.

RED: When the knobs are in turned to an ON position the indicator lights will be in a bright red to indicate which burner is in use, the oven / broiler has been turned on or the function selector knob has been turned to activate the rotisserie or to turn on the oven light.



GAS BURNERS

Gas flow to the burners is adjusted by turning the knobs which control the valves. Turning the knob so that the indicator line points to the symbols printed on the panel achieves the following functions:

When knob is rotated to the maximum position it will permit the rapid boiling of liquids, whereas the minimum position allows the simmer warming of food or maintaining boiling conditions of liquids.



Toreducethegasflowtominimum,rotatetheknobfurthercounter‐clockwisetopointtheMINposition. Otherintermediateoperatingadjustmentscanbe achievedbypositioningtheindicatorbetweentheMAX andMINpositions,andneverbetweentheMAXandOFFpositions.

Whentherangeisnotbeingused,setthegasknobstotheirOFFpositionsandalsoclosethegasshut‐off valveplacedonthemaingassupplyline.



LIGHTING GAS BURN E R S

In order to light the burner, you must:

– Push the knob all the way in, turn the knob in a counterclockwise direction up to the MAX

position (maximum rate) to ignite, and hold the knob until the flame has been lit and allow the system to heat to the appropriate temperature and allow the flow of gas (approximately 10 seconds). The sparks produced by the internal igniter will light the designated burner.

In the event that the local gas supply conditions make it difficult to light the burner in the MAX position, try again with the knob in MIN position.

– Adjust the gas valve to the desired position.

To re-light the burner, return the knob to the OFF position and repeat the operations for lighting.

Caution! The range becomes very hot during operation. Keep children well out of reach.

ATTENTION:FORYOURSAFETY: 

THISUNITHASBEENDESIGNEDWITHAFLAME SENSORSYSTEMTHATMONITORSTHECOOKTOP BURNERS.



Whenusingthecooktop,presstheknoballtheway in,turntoignitetheflameandholdfor approximately10secondstoallowthesystemto heattotheappropriatetemperatureandallowthe flowofgastotheselectedburner.





CHOICE OF BURNER

DIAMETERS OF PANS WHICH MAY BE USED ON THE TOP BURNERS

BURNER MINIMUM MAXIMUM

Auxiliary 4" 23/32 (12 cm) 5" 1/2 (14 cm)

Semirapid 6" 19/64 (16 cm) 9" 7/16 (24 cm)

Rapid 9" 7/16 (24 cm) 10" 15/64 (26 cm)

Do not use pans with concave or convex bases

The symbols printed on the panel above the gas knobs indicate the correspondence between the knob and the burner. The most suitable burner is to be chosen according to the diameter and volume capacity of the container to be warmed. It is important that the diameter of the pots or pans suitably match the heating potential of the burners in order not to jeopardize the efficiency of the burners, bringing about a waste of gas fuel. A small diameter pot or pan placed on a large burner does not necessarily mean that boiling conditions are reached quicker.

High – Altitude effects on burners: The surface burners used on this unit range from 2,500 BTU to 8,000 BTU on natural gas installation under 2,000 feet above sea level. Burner strength is derated by 4% per 1000 feet.

HOW TO USE THE GAS OVEN



GENERAL FEATURES

The gas oven is provided with two burners:

Oven burner, mounted on the lower part of the oven: Broil burner, mounted on the upper part of the oven:



USING THE OVEN FOR THE FIRST TIME

It is advised to follow these instructions –

Insert shelves and broiler grid and tray

–

Turn the oven on to the maximum temperature position (500F) to eliminate possible traces of grease from the oven burner. The same operation should be followed for the broiler burner (knob on position BROIL)

Unplug the power cord, let the oven cool down, then clean the interior of the oven with cloth soaked in water and detergent (neutral) then dry carefully.



OVEN BURNER

Carries out normal “oven cooking”. The gas flow to the burner is regulated by a thermostat which allows to maintain the desired oven temperature. The control of the temperature is assured by a thermostatic probe positioned inside the oven. The probe must be always kept in its housing, in a clean condition, as an incorrect position or a dirty probe may cause an alteration in the control of the temperature.

GAS OVEN SETTING

Number printed on the knob

Temperature

in °F

300

149

350

177

400

204

450

232

500

260

Corresponding temperature

in °C

OVEN THERMOSTAT

The numbers printed on the control panel indicate the increasing oven temperature value ( °F). To regulate the temperature, set the chosen number onto the control knob indicator.

The position BROIL serves only to turn on the broil burner.

NOTE: When the range will not be used for long periods of time, set the gas knobs to their positions and also close the gas shut-off valve placed on the main gas supply line.

VERY IMPORTANT: The oven/broil shall be used always with the door closed.

WARNING!!

WARNING-VERY IMPORTANT NOTICE

Never obstruct the oven vent slots on the backsplash.

 Do not broil without using the broiling pan.  Important: Use always suitable protective gloves when inserting / removing the broiling pan,

shelves, pans on other cooking utensils from the oven.

 Attention: the range becomes very hot during operation  Attention: the oven door becomes very hot during operation  Keep Children away  Warning: The door is hot, make sure to use the handle



IGNITION OF THE OVEN BURNER

The thermostat allows the automatic control of the temperature.

The gas delivery to the oven burner is controlled by a two way thermostatic tap (oven and broil burners) with flame-failure device.

To light the oven burner operate as follows:

Open the oven door to its full extent.

WARNING: Risk of explosion! The oven door must be open during this operation.

Lightly press and turn the thermostat knob counter-clockwise to max position or 500ºF

Press the knob inward and hold to activate the electronic ignition. Note that you will hear a “clicking” noise. Hold the knob pressed inward until the oven burner is lit. Once the oven burner is lit, release the knob.

In case of power outage, you can manually light the burner by pressing the knob inward and immediately approach a lighted match to the opening “A” (see the diagram above).

Never continue this operation for more than 15 seconds. If the burner has still not ignited, wait for about 1 minute prior to repeating the ignition.

When using the range for the first time or after long period of non-usage, keep pressing the knob inward for approximately 10 – 15 seconds after the burner has lit to ensure the gas valve has been accurately primed.

Close the oven door slowly and adjust the burner accordingly to the desired temperature. If the flame extinguishes for any reason, the safety valve will automatically shut off the gas supply to the burner.

To re-light the burner, first turn the oven control knob to the OFFposition, wait for at least 1 minute and then repeat the lighting procedure.

Attention: the oven door becomes very hot during operation. Keep children away.



OVEN COOKING

Before introducing the food, preheat the oven to the desired temperature For a correct preheating operation, it is advisable to remove the tray from the oven and introduce it together with the food, when the oven has reached the desired temperature. Check the cooking time and turn off the oven 5 minutes before the theoretical time to recuperate the stored heat

IGNITION OF THE BROIL BURNER

The broil burner generates the infra-red rays for broiling. To light the broil burner operate as follow: To light the oven burner operate as follows:

Open the oven door to its full extent.

WARNING: Risk of explosion! The oven door must be open during this operation.

Lightly press and turn the thermostat knob clockwise to the broil position.

In case of power outage, you can manually light the burner by pressing the knob inward and immediately approach a lighted match to the area “A” (see the diagram above).

Never continue this operation for more than 15 seconds. If the burner has still not ignited, wait for about 1 minute prior to repeating the ignition.

Slowly close the oven door. If the flame extinguishes for any reason, the safety valve will automatically shut off the gas supply to the burner.

To re-light the burner, first turn the oven control knob to the position, wait for at least 1 minute and then repeat the lighting procedure.

Always broil with oven door closed. Attention: the oven door becomes very hot during operation. Keep children away.



BROILING

Very important: the broil burner must always be used with the oven door closed.

Position the oven rack on the second level from the top

-Turn on the broil burner, as explained in the preceding paragraphs and let the broil burner preheat

for about 5 minutes with the door closed.

-Place the food to be cooked above the broiling pan.

-Introduce the broiling pan in the oven. The broiling pan should be placed above the shelf and it should be centered with the broil burner.

ROTISSERIE (MODEL DGR24P3S – ONLY)

This range is equipped with an automatic rotisserie for roasting. The rotisserie feature allows for an even cooking and all-over browning of

the meat while preventing the meat from cooking in its rendered grease. The rotisserie will turn the meat allowing it to baste itself while roasting.

Be sure that you have received the rotisserie accessories included with your unit.

(1)

Rotisserie Spit – Rod

(2)

Rotisserie Forks

Always use the included broiling pan when using the rotisserie to catch the rendered grease and allow for easy access to the meat when putting in and removing the rotisserie spit – rod.

Your range offers two settings for the rotisserie function, rotisserie with the oven light on and with the light off.

To use the rotisserie, preheat the oven to the desired temperature. Secure the meat to be cooked onto spit-rod using the rotisserie forks. Insert the rotisserie spit-rod into the rotating assembly and select the desired rotisserie function (light

on or light off). Be sure the baking / broiling tray is below the meat being cooked to avoid spills and to prevent

possible flare-up of the oven flame. ALWAYS TURN THE ROTISSERIE FUNCTION TO OFF BEFORE REMOVING THE ITEMS FROM

THE OVEN. CAUTION – USE HEAT RESISTANT GLOVES WHEN REMOVING THE ITEMS FROM THE OVEN.

OVEN LIGHT

The range is equipped with a light that illuminates the oven to enable visually controlling the food that is cooking.

This light is controlled by a knob on the control panel. Simply turn the knob to the position marked with the light bulb on the right to turn on the oven light.

Model DG24P3S ONLY - the knob also has two additional positions marked with a bulb and a rotisserie icon as well as a rotisserie icon without light; this is to give you the option of having the light on or off during cooking with the rotisserie.



CARE & MAINTENANCE

GENERAL RECOMMENDATION

Important: Before any operation of cleaning and maintenance disconnect the appliance from the electrical supply.

It is advisable to clean when the appliance is cold and especially for cleaning the enameled parts.、

Avoid leaving alkaline or acidic substances (lemon juice, vinegar, etc.) on the surfaces. Avoid using cleaning products with a chlorine or acidic base. The oven must always be cleaned after every use, using suitable products and keeping in mind that its operation for 30 minutes on the highest temperature eliminates most grime reducing it to ashes.

ENAMELED PARTS

All the enameled parts must be cleaned with a sponge and soapy water only or other non-abrasive products. Dry preferably with a chamois leather.

If acid substances such as lemon juice, tomato conserve, vinegar etc. are left on the enamel for a long time they will etch it, making it opaque.

STAINLESS STEEL ELEMENTS

Stainless steel parts must be rinsed with water and dried with a soft and clean cloth or with a chamois leather.

For difficult dirt, use a specific non-abrasive product available commercially or a little hot vinegar.

Note: regular use could cause discoloring around the burners, because of the high flame temperature.

INSIDE OF OVEN

This must be cleaned regularly. With the oven warm, wipe the inside walls with a cloth soaked in very hot soapy water or another suitable product.

GAS VALVES

In the event of operating faults in the gas valves, shut the main gas supply and call the Service Department.



Do not use steam jet cleaners because the humidity could infiltrate into the appliance making it dangerous.

BURNERS AND CAST-IRON GRIDS

✓ These parts can be removed and cleaned with appropriate products. ✓ After cleaning, the burners and their flame distributors must be well dried and correctly replaced. ✓ It is very important to check that the burner flame distributor and the cap has been correctly

positioned - failure to do so can cause serious problems.

✓ In appliances with electric ignition keep the electrode clean so that the sparks always strike. ✓ Note: To avoid damage to the electric ignition do not use it when the burners are not in

place.

CORRECT REPLACEMENT OF THE BURNERS

It is very important to check that the burner flame spreader “F” and the cap “C” have been correctly positioned. Failure to do so can cause serious problems.

In appliances with electric ignition, check that the electrode “S” is always clean to ensure trouble-free sparking.

The ignition plug must be cleaned very carefully.

OVEN RACK INSTALLATION AND REMOVAL

The oven racks are provided with a safety catch to prevent accidental extraction.

They must be inserted as shown.

To pull them out remove the rack in the reverse order.



REMOVABLE STORAGE DRAWER

① Lift the left small hook upward, at the same time, push the right small hook downward.(see the picture )

②Pull the drawer out.

③To replace the drawer, align the

drawer with the rails and push inward.

Do not store flammable material in the oven or in the bottom drawer.

REMOVING THE OVEN DOOR

To facilitate oven cleaning, it is possible to remove the door. Please follow the instructions carefully:

REMOVING THE OVEN DOOR

–

The oven door can easily be removed as follows:

–

Open the door to the full extends.

–

Lift the left and right hooks on the hinge.

–

Hold the door as shown in the figure.

–

Gently close the door and lift the door with two hands when the hooks touch the door.

–

Set the door on a soft flat surface.

–

To replace the door, repeat the above steps in reverse order.

hook



+ 53 hidden pages