Avago Technologies SAS 9201-16i User Manual

Quick Installation Guide
LSI® SAS 9201-16i PCI Express® to 6Gb/s SAS Host Bus Adapter

To install the LSI® SAS 9201-16i HBA, follow these steps:

1. Unpack the HBA, and inspect it for damage. Unpack the HBA in a static-free environment.
Remove the HBA from the antistatic bag, and carefully inspect the device for damage. If you notice
any damage, contact LSI or your reseller support representative.

ATTENTION: To avoid the risk of data loss, make a backup of your data before changing your

system configuration.

2. Prepare the computer. Turn off the computer, and remove the power cord from the rear of
the power supply.

CAUTION: Disconnect the computer from the power supply and from any networks to which

Thank you for purchasing the
LSI SAS 9201-16i Host Bus Adapter
(HBA). Please take a few minutes to
read this quick installation guide
before you install the HBA.

For more information about any
topic covered in this guide, refer to
the documents listed with your
product at the following link:

http://go.lsi.com/hbas

3. Remove the cover from the chassis.

4. Insert the HBA in an available PCIe® slot. Locate an empty PCIe slot. Remove the blank

bracket panel on the back of the computer that aligns with the empty PCIe slot. Save this bracket
screw, if applicable.
Align the HBA to a PCIe slot. Press down gently, but firmly, to seat the HBA correctly in the slot. The
following figure shows how to insert the HBA in a PCIe slot.

you will install the HBA, or you risk damaging the system or experiencing
electrical shock.

After navigating to your product, select
Software Downloads to locate necessary
device drivers.

ATTENTION: Perform all installation work

at an electrostatic discharge
(ESD)-safe workstation that
meets the requirements of
EIA-625.

Handling Electrostatic Discharge
Sensitive Devices. You must

perform all actions in
accordance to the latest
revision of the IPC-A-610 ESD­recommended practices.

Requirements for

NOTE: The shape, size, and locations of the components on your HBA and its bracket might vary

from this illustration. The HBA requires a x8 PCIe slot.

5. Secure the HBA bracket to the system’s chassis. Install the bracket screw, if applicable, or
engage the system retention mechanism to secure the HBA to the system’s chassis.

47212-01A

6. Connect SAS cables between the HBA and the SAS backplane that contains any other
SATA or SAS devices. The LSISAS9201-16i has four internal x4 mini-SAS connectors, each

connecting to four 6Gb/s SAS ports. Use the appropriate cable to connect the HBA to SAS or SATA
storage devices.
For connection to internal drives or backplanes, use an internal cable with a standard mini-SAS
connector (SFF-8087) on the controller side of the cable. The other end of the cable may fan out
into four SAS-style cables for direct connection to SAS or SATA disk drives. The previous figure
shows the connector locations on the LSISAS9201-16i and the use of a controller-based, fan-out
cable to connect to drives that require a SAS-style signal connector.

7. Replace the cover and any power cords, and power up the system. Replace the chassis’s
cover, reconnect any power cords, and reconnect any network cables. Turn on the power.

The hardware installation of your LSI 6Gb/s SAS HBA is complete. The next procedure is to install
the appropriate operating system drivers.

DRIVER INSTALLATION

All driver installation instructions are available at http://go.lsi.com/hbas. Select 6Gb/s SAS HBAs >
Product Name > Software Downloads.

TECHNICAL SUPPORT

For assistance installing, configuring, or
running the LSI SAS 9201-16i HBA, contact LSI
Technical Support:

E-mail: [e-mail]

Web Site: www.lsi.com/support/

WARRANTY NOTICE

1. The warranty does not cover the return

of parts damaged by changing the bracket.

2. The warranty does not cover ESD
damage to the HBA. HBAs returned without a
bracket mounted on the board will be
returned without return merchandise
authorization (RMA) processing.

Avago Technologies, the A logo, LSI, and Storage by LSI are trademarks of Avago Technologies in the United States and/or other countries. All
other brand and product names may be trademarks of their respective companies.

Corporate Headquarters Email Website
San Jose, CA [e-mail] www.lsi.com

Document Number: 47212-01A
Copyright © 2014 Avago Technologies
All Rights Reserved. October 2014.