Autostart AS-3472TW-FM User Manual

TWO-WAY 6-BUTTON LCD AUTOMATIC/MANUAL

TRANSMISSION REMOTE STARTER

AS-3472TW-FM

User Guide

FCC USER NOTICE (U.S.A.):

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user's authority to operate the equipment.

It is the responsibility of the vehicle operator to ensure their vehicle is parked in a safe and responsible manner.

1. a) Manual transmission responsibility to ensure that the gearshift lever is in the NEUTRAL position and the parking brake is engaged in order to avoid accidents upon remote starting.

b) Automatic transmission

responsibility to ensure that the gearshift lever is in “Park” in order to avoid accidents upon remote starting. (Note: Make sure that the automatic vehicle cannot start in "Drive".)

2. It is the user's responsibility to ensure that the remote starter is disabled or put into valet mode before servicing.

WARNING

: When leaving the vehicle, it is the user’s

DOC: 1.00 - AS-3472TW-FM - - July 3, 2008 - - MO - Made in China

Table of Contents

Introduction ............................................................ 2

Using the Transmitter ............................................ 3

LCD Remote Functions ...................................... 3

Vehicle Presets....................................................... 7

Heater & Heated Seat......................................... 7

Windshield Wipers, Radio & Headlights ............. 7

Arming the Starter Kill ........................................... 7

Remote-Starting Your Vehicle .............................. 8

Setting Your Vehicle Into Ready Mode............... 8

Remote-starting .................................................. 9

Driving Off ........................................................... 9

Remote Starter Features ....................................... 9

Idle Mode ............................................................ 9

Valet Mode........................................................ 10

Panic Mode ....................................................... 11

Quick Lockout

Cold Weather Mode .......................................... 11

The Starter Kill and the Anti-grind Feature....... 12

Extended Run Time .......................................... 12

Advanced Features: Installation-programmable

Options.................................................................. 12

Passive or Active Arming of the Starter Kill...... 13

OEM-Style Alarm .............................................. 13

Remote Door Locks .......................................... 13

Priority Door Access ......................................... 13

Ignition-Controlled Door Locks......................... 13

................................................ 11

Ignition Relock .................................................. 13

Secure Lock ...................................................... 13

Remote Trunk Release..................................... 13

Safe Start .......................................................... 14

Installer-programmable Valet Mode ................. 14

“Home Valet

Turbo Mode....................................................... 14

Engine Run Time .............................................. 15

How to Access to Runtime Status (Indication

purpose only) ...............................................15

Temperature Request (If ACC-Temp-101

installed)............................................................ 15

Constant While Pressed ................................... 15

Horn Chirp Timing............................................. 15

Multi-car Operation ........................................... 15

LCD Transmitter Operation and Confirmations

(Second Car Control)........................................... 16

Basic Operations............................................... 16

Start/Stop While in Safe Start Mode................. 16

Missing a Start or a Stop Confirmation ............. 17

Multi-Level Features (default state) ................... 17

Accessing the Multi-Level Features and Other

Transmitter Functions ....................................... 18

Troubleshooting Transmitting Range................ 19

LIMITED LIFETIME WARRANTY ......................... 20

” Mode ..................................14

Introduction

This is a state-of-the-art remote car starter system. The system is packed with advanced features such as priority access to the driver’s door (commodity features) and the Safe Start children safety feature. With many advanced functions, this product will satisfy any one of your expectations from high-end commodity and security systems, without neglecting any standard feature commonly offered by entry-level starters.

P. 2 User Guide

Using the Transmitter

Your remote starter is equipped with a 5-button multi-channel remote control. It can operate two independent vehicles equipped with identical remote starters (see Multi-car operation section, later in this Guide, for second-car transmitter functions).

LCD Remote Functions

The transmitter offers several command-confirmation and timer features. This section explains some of the key functions available. The next section gives a summary of the button combinations used to access the functions.

Note: If you wish to exit a function while still in the process of accessing it, simply stop and wait at least 5 seconds: the transmitter will return to its normal state.

The functions of the transmitter are as follows:

LOCK Button:

Locks all Doors and arms the Starter Kill

AUX (if programmed):

• AUX 2 output

• Stop

• Temperature request

• Panic

• CWM

TRUNK Button:

Activates the Trunk output (AUX 3)

F button Functionality: (By default)

button

1x Level 1 L – 01 Enables backlight 2x Level 2 L – 02 Enables backlight 3x Level 3 L – 03 Enables backlight 4x Enters programming mode MENU Enables backlight

Note: The order of LEVELS and MENU can be re-arranged in the menu option FBPRO.

Backlight:

Press and hold the

Backlight

ON for 3 seconds. If the button is pressed down for more than 5 seconds, the

backlight will stay

button quickly (for less than 1 second): the backlight will turn ON 3 seconds.

the

Function Button (F): . Turns On the backlight . For accessing Multi-level functions and Menu

UNLOCK Button:

Unlocks all Doors and disarms the Starter Kill

START/STOP Button:

Starts or Stops the engine (Normal functions)

Press

Less than 3 seconds

button (for more than 3 seconds and less than 5 seconds), to turn the

ON until the button is released. A quick way to access the backlight is to press

LCD display

Press

more than 3 seconds

User Guide P. 3

Button

Press for < 1 second Backlight ON for 3 sec.

Press for > 3 seconds and < 5 seconds Backlight ON for 3 sec.

Press for > 5 seconds

Backlight will stay

Backlight

ON until button is released.

Selecting and adjusting Menu options:

 When in

 Press  Press

 Press

MENU, press button to enter the menu.

button to move up in the menu or button to move down in the menu.

button to select the option you would like to adjust.

button to increase the value, activate or deactivate a function or toggle through the

selection.

 Press

button to decrease the value, activate or deactivate a function or toggle through the

selection.

 Press button to move to the next sub-option or go back to the main menu.

Order Menu Option LCD display Function

1 Parking Menu PARK

Parking hour

Parking minute

2 Alarm Clock Menu ALARM

Alarm hour

Alarm minute

Toggle alarm

3 CWM Menu CWM Cold Weather Mode

Toggle CWM mode

4 VALET Menu VALET

Toggle valet mode

5 Time Start Menu TSTAR

Time start hour

Time start minute

Toggle time start

6 SECURE Menu SECUR Lock the transmitter keypad

Toggle lock remote

7 Backlight Color Menu COLOR

Backlight There are 8 different Blue lights is default

Toggle Parking

countdown

P 0:00

0 is flashing

P 0:30

30 is flashing

P -- ON

P – OFF

A 12:00

12 is flashing

A 12:00

00 is flashing.

A -- ON

A – OFF

OFF

T 12:00

12 is flashing.

T 12:00

00 is flashing

T -- ON

T – OFF

PRESF

when remote is locked.

Adjust parking hour(s)

(value from 0 to 2)

Adjust parking minute(s)

(value from 0 to 59)

Enable or disable parking countdown

There is a beep 5 min. before the

parking countdown reaches 0.

Adjust alarm hour(s)

(value from 0 to 12)

Adjust alarm minute(s)

(value from 0 to 59)

Enable or disable alarm

Adjust time start hour(s)

(value from 0 to 12)

Adjust time start minute(s)

(value from 0 to 59)

Enable or disable

Selecting PRESF will unlock the

transmitter keypad

P. 4 User Guide

8 LCD On Menu LCD

LCD on time

9 Clock Menu CLOCK

Clock hour

Clock minute

10 Temperature Menu TEMP

Temperature

11 Language Menu LANGU

Language

12 Side button Menu SBPRO Side Button Programming

Keypad lock time

14 Illumination Menu ILLUM

FB programming

Keypad Lock Time

Toggle Illumination

Mode

F Button Function

colors

OFF 01 OFF 15 OFF 30 OFF 60

12:00

12 is flashing.

12:00

00 is flashing.

CTEMP

FTEMP

ENG

FRAN

PANIC

STOP TEMP

AUX 2

CWM

KELOC

05 10 20

OFF

FBPRO F Button Programming

1 2 3 M 2 3 1 M 2 1 3 M 3 1 2 M M 1 2 3

1 min., 15 min., 30 min., 60 min. and

1 min. is default.

Adjust clock hour(s) (value from 0 to 12)

Adjust clock minute(s)

(value from 0 to 59)

Deg Celsius or Fahrenheit

Deg. Celsius is default

English is default

AUX 2 output, Stop, Temperature

request, Panic, CWM ( Cold weather

mode)

When SECURE is ON, Keypad will be locked automatically 5 sec./10 sec./20

sec. after the MENU operation ends.

ON – basic operation with backlight illumination; OFF – basic operation

without backlight illumination.

Parking Countdown: This version of the countdown feature is particularly useful for keeping track of parking meter time: the user may quickly set up the countdown using the 5 minutes before the Parking countdown reaches 0.

Parking Menu. The transmitter will beep once,

Alarm Clock:

The LCD remote control has a built-in alarm clock, which can be set up using the

. Once the programmed time is reached, the remote will beep 6 times every minute until a

button is pressed.

Alarm Clock

CWM menu:

When this feature is enabled, press

for 3 seconds to enter or exit Cold Weather mode. If

disabled, press then button to enter or exit Cold Weather mode.

User Guide P. 5

Valet menu:

When this feature is enabled, press

+ buttons simultaneously.

to enter Valet mode. When this feature is disabled, press

Time start menu:

This feature is used to remote start the car at a pre-programmed time. Once the pre-programmed time is reached, the remote will send a start command to the car module.

Secure Remote feature:

This feature is used to lock the keypad of the transmitter to avoid accidental button press. When the remote is locked and a button is pressed, the LCD displays “PRESF” for 1 second, then goes back to the clock. The transmitter keypad can also be locked as follows:

• Press to go to Menu.

• Within 3 seconds, press .

• Press for about 1 second to unlock the transmitter keypad.

LCD ON menu:

If there is no activity within the programmed time, the LCD will turn off. This feature maximizes the lifetime of the battery.

Clock Menu: The Clock menu is used to set the current time on your remote control.

Side button Menu:

The side button can be programmed as one of the following buttons:

• Panic button;

• Stop button;

• Temperature request button;

• AUX 2 output button;

• or CWM.

F Button Function Menu: The order of

LEVELS and MENU can be re-arranged using the F Button Function Menu.

Button Operation:

Button LCD Beep(s)

Lock button Lock icon + LOCK 1 beep

Unlock button Unlock icon + ULOCK 2 beeps

Trunk button TRUNK text for 1s 1 beep

Start button START text for 1s 1 beep

Engine running

Run time +

icon + Blue backlight for 3s

Engine stop Red backlight on for 3s 2 beeps Unlock+Start button Valet icon if pressed more than 3s 1 beep Lock+Unlock button 1 beep

Trunk+Lock button

(2nd car operation)

Trunk+Unlock button

(2nd car operation) Trunk+Start button (2nd car operation)

L --01 → Lock button

L --01 → Unlock button

Lock icon + LOCK 1 beep

Unlock icon + ULOCK 2 beeps

START text for 1s 1 beep

1 beep

3 beeps

P. 6 User Guide

+ 14 hidden pages