Autostart AS-1795 Quick Guide

Ü·¿¹²±-¬·½- Š Ð¿®µ·²¹ Ô·¹¸¬ Ú´¿-¸ Ì¿¾´»

Flashes Description

3 slow flashes… …after a failed start attempt The module did not detect a tach signal.

5 Slow Start attempt failed because no tach signal has been programmed.

5 Fast Tach signal programmed.

6 A remote start was attempted while a tach-before-crank signal was detected before cranking. 8 Unit reset see “Resetting the Module” (p.Error! Bookmark not defined.)

10 A ground (-) signal was detected on the hood pin input wire.

1 pause

5 flashes [During the transmitter programming procedure]

1 – pause – 2

seconds….

ON continuously

ON 2 seconds ON 4 seconds Locking or unlocking a door (with Door pulses configured to 4 sec.)

ON 20 seconds The hood pin has been flashed and you are now in the programming centre.

Constant flashes

up to 25 sec.

Doors locked, starter kill armed. Run time has expired.

TRUNK button pressed.

Start signal received by the module.

Cold weather mode cancelled. Remote start attempt cancelled by remote. Doors unlocked, starter kill disarmed. Exiting ignition valet Exiting remote valet Power-up reset Entering cold weather mode. Entering ignition valet. Entering remote valet. Entering extended run time.

+12 V detected on the brake input wire either while cranking or during run time. Entering multi-speed tach programming.

Transmitter has been programmed.

There was a remote start attempt while the vehicle was in valet mode. Failed start: vehicle’s low battery voltage.

…followed by 1 flash Exiting cold weather mode ON SOLID for 3 …followed by 3 flashes Entering cold weather mode

Idle mode: Idle mode is engaged Run time: The vehicle has been remote started and is in run time.

While the brake pedal is pressed.

The hood has been opened and a ground (-) signal has been detected on the hood pin input wire.

Panic mode was triggered.

Confirms that cold weather mode is engaged

У Я Т Л Я Ф МОЯТНУЧННЧСТ ОЫУСМЫ НМЯОМЫО

ЯНупйзл

Ï«·½µ ×²-¬¿´´¿¬·±² Ù«·¼»

Ì¿¾´» ±º Ý±²¬»²¬-

Ш±© ¬± Ъ´¿-¸ ¬¸» Ш±±¼ Р·²тттттттттттттттттттттттп М®¿²-³·¬¬»® Р®±¹®¿³³·²¹ Р®±½»¼«®»тттттп Ы²¬»®·²¹ Р®±¹®¿³³·²¹ С°¬·±²-тттттттттттттттп Р®±¹®¿³³·²¹ С°¬·±²-тттттттттттттттттттттттттттттто М¿½¸ Р®±¹®¿³³·²¹тттттттттттттттттттттттттттттттттттн Ш±®² Ш±²µ М·³·²¹тттттттттттттттттттттттттттттттттттттн О»-»¬¬·²¹ ¬¸» У±¼«´»ттттттттттттттттттттттттттттттттн Н«°°´»³»²¬¿®§ Ч²º±®³¿¬·±²тттттттттттттттттттттк

Ø±© ¬± Ú´¿-¸ ¬¸» Ø±±¼ Ð·²

THE INSTALLER … THE MODULE …

Press and hold the hood pin for 4 seconds. Release the hood pin. Parking Lights “ON” While the parking lights are on, press down the hood pin once more and release the hood pin immediately, before the parking lights turn off. You now have 20 seconds to select one of the sub-menus

Ì®¿²-³·¬¬»® Ð®±¹®¿³³·²¹ Ð®±½»¼«®»

1. Flash the hood pin (see above) -- the parking lights will stay on for up to 20 seconds.

2. Before the lights go out, turn the ignition key to the IGNITION ON (RUN) position and immediately to the OFF position.

3. Press and hold the LOCK button and keep it down until the parking lights flash 5 times quickly.

4. The transmitter has been stored in memory.

5. To exit: close the hood. To program a transmitter on the second vehicle for multi-car operation, you must press the TRUNK button (instead of LOCK

or UNLOCK) in step 3 of the transmitter programming procedure:

Û²¬»®·²¹ Ð®±¹®¿³³·²¹ Ñ°¬·±²-

1. Flash the hood pin switch (see on page 1) the parking lights will stay on for up to 20 seconds.

2. Before the lights go out, press and hold the brake pedal and then press one of the following buttons:

3. The parking lights will flash and the horn will honk (if programmed) once, twice or three times to confirm entry into a mode.

4. Release the brake pedal.

LOCK ..................................................to access mode 1;

UNLOCK..........................................to access mode 2 or;

TRUNK................................................to access mode 3.

Ъ·º¬¸ О»´¿§ С«¬°«¬ шо²¼ ЧЩТф ЯЭЭ ±® ЭОЯТХчттттттттттттттттттттттттттттттттттттттттттттттттттк М¿½¸ ¶«³°»® -»¬¬·²¹-ттттттттттттттттттттттттттттттк

М»-¬·²¹тттттттттттттттттттттттттттттттттттттттттттттттттттттттк Ь·¿¹²±-¬·½- Š Р¿®µ·²¹ Ф·¹¸¬ Ъ´¿-¸ М¿¾´»ттттттттттттттттттттттттттттттттттттттттттттттттттттттттттти

“ON” for 20 seconds

Ì± ±¾¬¿·² ¿ ½±°§ ±º ¬¸» ·²-¬¿´´ ¹«·¼»ô °´»¿-» ª·-·¬ ¬¸»

¸¬¬°æññ©©©ò¿«¬±-¬¿®¬ò½¿ ©»¾-·¬» ¿²¼ ½´·½µ ±² ¬¸»

u Ü±©²´±¿¼ e ¬¿¾ò

P. 8 ¸¬¬°æññ©©©ò¿«¬±-¬¿®¬ò½¿ Installation Guide

Ò±¬·½»

The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of the product, be that either damage to the vehicle itself or to the unit. This unit must be installed by a certified technician using all safety devices supplied. Please note that this guide has been written for properly trained Autostart technicians: a certain level of skills and knowledge is therefore assumed. Please review the installation guide carefully before beginning any work.

É¿®²·²¹

This Remote Car Starter is designed for vehicles with a manual Transmission only. Before installing the Unit, test that the OEM Door Switch contacts of the vehicle work well, and that the Parking Brake system operates properly.

DOC.1.02 – January 9, 2007 DL Lp Manufactured in Canada by Autostart

After selecting the function, press one of the corresponding buttons to select the option.

LOCK for Option 1; UNLOCK for Option 2; TRUNK for Option 3; START for Option 4.

Ð®±¹®¿³³·²¹ Ñ°¬·±²-

MODE 1 * indicates default setting

FUNCTION 1 – Ignition-controlled door locks

OPTION 1* Ignition lock disabled

OPTION 2 Ignition lock enabled OPTION 3 Ignition unlock only OPTION 4 Ignition lock only

FUNCTION 2 – Secure Lock

OPTION 1* Secure Lock disabled

OPTION 2 Secure Lock enabled in standard mode OPTION 3 Secure Lock enabled in smart mode

FUNCTION 3 – Passive or Active Arming

OPTION 1* Passive arming (60 sec.)

OPTION 2 Active arming OPTION 3 Passive arming (3 min.)

FUNCTION 4 – Door lock pulse timing

OPTION 1* 7/10-sec. lock/unlock pulses

OPTION 2 4-sec. Lock/Unlock pulses OPTION 3 7/10-sec. Lock pulse and two ¼-sec. Unlock pulses OPTION 4 1/10-sec. Lock/Unlock pulses

FUNCTION 5 – LED flashing

OPTION 1* Enabled (without starter kill will flash only when ignition is OFF)

OPTION 2 Disabled OPTION 3 Enabled (with starter kill will flash when the starter kill engages. This option should be selected ONLY if the starter kill is installed.)

MODE 2 * indicates default setting

FUNCTION 1 – Safe Start.

OPTION 1 Safe start enabled OPTION 2* Safe start disabled

OPTION 3 “Swap Start” – enhanced safe start mode with extended safety: To start the engine: press the LOCK and UNLOCK buttons simultaneously To trigger AUX 2: press the START button

FUNCTION 2 – Engine Run Time

OPTION 1 Run Time = 3 minutes in gas mode / 8 minutes dieselmode

OPTION 2* Run Time = 15 minutes in gas mode / 20 minutes diesel mode

OPTION 3 Run Time = 25 minutes in gas mode / 30 minutes dieselmode

FUNCTION 3 – Idle Mode / Turbo Mode

OPTION 1 Idle Mode enabled / Turbo mode enabled OPTION 2* Idle Mode enabled / Turbo mode disabled

FUNCTION 4 – Engine type and cold weather mode

OPTION 1 Diesel mode with 20-minute run time in cold weather mode (30 sec. delay)

OPTION 2* Gas mode with 3-minute run time in cold weather mode

OPTION 3 Diesel mode with 8-minute run time in cold weather mode (18 sec delay) OPTION 4 Diesel mode with 8-minute run time in cold weather mode (7 sec delay)

FUNCTION 5 – Ignition Valet

OPTION 1 Ignition valet disabled

OPTION 2* Ignition valet enabled

Hood switch shutdown. With the vehicle running under the remote car starter, open the hood; the vehicle

should shut down. If it does not shut down, check the hood pin-switch and its connector. Brake shutdown circuit. With the vehicle running under the remote car starter, press and release the brake

pedal. The engine should shut down immediately. If the engine continues to run, check the brake switch connection.

Door locks and trunk testing. Make sure each of these options respond to the transmitter (if installed). Starter kill option. Sit inside the vehicle with all doors closed. Arm the vehicle, then try to start the engine with

the key. They engine should not start. If the engine starts, rewire the starter kill to reach proper operation. Valet mode. Make sure the remote car starter is able to properly enter and exit valet mode. When setting the

remote car starter into valet mode, pressing the lock button will lock the doors without activating the starter kill. (Refer to the user guide for further information on valet mode.)

Idle mode. Make sure the vehicle properly enters and exits idle mode. Most comebacks are the result of misunderstandings about how a product works or performs. Take the

time to properly explain all functions and features to the customers before they leave the premises. Doing this will save time and money.

MODE 3 * indicates default setting

FUNCTION 1 – Home Valet

OPTION 1 Home Valet enabled

OPTION 2* Home Valet disabled

FUNCTION 2 – AUX 2 Programming

OPTION 1 Constant output while the LOCK and UNLOCK buttons are pressed. In Safe Start Mode: activate AUX 2 by pressing the START button.

OPTION 2* Toggle ON/OFF (with 30-second timeout)

OPTION 3 Horn confirmation when lock. OPTION 4 Priority Door Access

+ 2 hidden pages