Product Specification
) Preliminary Specification
AU OPTRONICS CORPORATION
( V
( ) Final Specification
u
Mod
le 17.0”
Model Name G170EG01 V1
SXGA Color TFT-LCD
G170EG01 V1
Customer Date
Approved by
Checked &
Approved by
Debbie Chiu 2011
Prepared by
Jimmy Tsai
2011
Date
/04/06
/04/06
Note: This Specification is subject to change without
ce.
noti
document version 0.4
Desktop Display Business Group /
AU Optronics corporation
1/26
Product Specification
AU OPTRONICS CORPORATION
G170EG01 V1
Contents
1. Handling Precautions ..................................................................................................................
4
2. General Description.....................................................................................................................5
2.1 Display Characteristics ..........................................................................................................5
2.2 Optical Characteristics ........................................................................................................... 6
3. Functional Block Diagram.........................................................................................................10
4. Absolute Maximum Ratings...................................................................................................... 11
4.1 TFT LCD Module.................................................................................................................. 11
4.2 Backlight Unit ....................................................................................................................... 11
4.3 Absolute Ratings of Environment ........................................................................................ 11
5. Electrical characteristics ..........................................................................................................12
5.1 TFT LCD Module.................................................................................................................. 12
5.2 Backlight Unit ....................................................................................................................... 14
6. Signal Characteristic .................................................................................................................15
6.1 Pixel Format Image..............................................................................................................15
6.2 The Input Data Format.........................................................................................................15
6.3 Signal Description ................................................................................................................ 16
6.4 Timing Characteristics.......................................................................................................... 18
6.5 Power ON/OFF Sequence...................................................................................................20
7. Connector & Pin Assignment ...................................................................................................22
7.1 TFT LCD Module.................................................................................................................. 22
7.2 Backlight Unit ....................................................................................................................... 23
8. Reliability Test............................................................................................................................24
9. Label and Packaging .................................................................................................................25
9.1 Shipping Label (on the rear side of TFT-LCD display)........................................................25
9.2 Carton Package ...................................................................................................................25
10. Mechanical Characteristics ....................................................................................................26
document version 0.4
2/26
Product Specification
AU OPTRONICS CORPORATION
G170EG01 V1
ecord of Revision
R
Version and Date
0.1 2011/01/12 All First Edition for Customer All
0.2 2011/01/14 5
24
0.3 2011/01/24 11
26
Page
Old description New
Thickness= 15.8 mm Thickness= 18.0 mm
350
Description Remark
0.4 2011/04/06 5, 6
5
11
Optical ResponseTime= 5 ms Optical ResponseTime= 30 ms
This module does not contain an
inverter card for backlight.
This module embbededs an LED
driver on it.
document version 0.4
3/26
. Handling Precautions
1
Product Specification
AU OPTRONICS CORPORATION
G170EG01 V1
1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input connector.
3)
Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth when
handling.
7) Do not open or modify the Module Assembly.
8) Do not press the reflector sheet at the back of the module to any directions.
9) In case if a Module has to be put back into the packing container slot after once it was taken out
from the container, do not press the center of the LED light bar edge. Instead, press at the far ends
of the LED light bar edge softly. Otherwise the TFT Module may be damaged.
10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the
Interface Connector of the TFT Module.
11) After installation of the TFT Module into an enclosure, do not twist nor bend the TFT Module even
momentary. At designing the enclosure, it should be taken into consideration that no
bending/twisting forces are applied to the TFT Module from outside. Otherwise the TFT Module
may be damaged.
12) Small amount of materials having no flammability grade is used in the LCD module. The LCD module
should be supplied by power complied with requirements of Limited Power Source (IEC60950 or
UL1950), or be applied exemption.
document version 0.4
4/26
Product Specification
AU OPTRONICS CORPORATION
G170EG01 V1
2. General Description
LCD
This specification applies to the 17 inch Color TFTThe display supports the SXGA+ (1280(H) x 1024(V)) screen format and 16.7M colors (RGB 6-bits+Hi-FRC
data).All input signals are 2 Channel LVDS interface compatible.
This module embbededs an LED driver on it.
Module G170EG01 V1.
2.1 Display Characteristics
The following items are characteristics summary on the
Items Unit Specifications
table under 25
condition:
Screen Diagonal [mm]
432 (17.0”)
Active Area [mm] 337.920(H) × 270.336(V)
Pixels H x V 1280 × 3(RGB) × 1024
Pixel Pitch [mm] 0.264(per one triad) × 0.264
Pixel Arrangement R.G.B. Vertical Stripe
Display Mode Normally White
White Luminance [cd/m2] 350
Contrast Ratio 1000 : 1 (Typ)
Optical ResponseTime [msec] 30 (Typ)
Nominal Input Voltage VDD [Volt] +5.0 (Typ)
Power Consumption
(VDD line + LED line)
[Watt]
22 W (Typ.)
(with LED driver, all black pattern)
Weight [Grams] 1800 Typ.
Physical Size (H x V x D) [mm] 358.5(H) x 296.5(V) Typ. x 18.0(D) Max.
Electrical Interface Dual Channel LVDS
Surface Treatment Anti-glare type, Hardness 3H
Support Color 16.7M colors (RGB 6-bits +Hi-FRC data)
Temperature Range
Operating
Storage (Non-Operating)
[oC]
[oC]
-30 to +85
-30 to +85
RoHS Compliance RoHS Compliance
document version 0.4
5/26
Product Specification
AU OPTRONICS CORPORATION
.2 Optical Characteristics
2
The optical characteristics are measured under stable conditions at 25
Item Unit Conditions Min. Typ. Max. Note
G170EG01 V1
(R
T
oom
empera
)
t
re
u
:
Viewing Angle [degree]
Horizontal (Right)
CR = 10
(Left)
Vertical (Up)
CR = 10
(Down)
Horizon (Right)
CR = 5
Vertical
(Left)
(Up)
CR = 5 (Down)
70
70
70
70
75
75
75
75
85
85
80
80
85
85
85
85
Luminance Uniformity [%] 9 Points 75 80
Rising - 20 25
Optical Response Time [msec]
Falling - 10 15
Rising + Falling - 30 40
Red x TBD TBD TBD
Red y TBD TBD TBD
Green x TBD TBD TBD
-
1
-
-
- 2, 3
4, 6
Color / Chromaticity
Green y TBD TBD TBD
Coordinates
(CIE 1931)
Blue x TBD TBD TBD
Blue y TBD TBD TBD
White x 0.283 0.313 0.343
White y 0.299 0.329 0.359
White Luminance
(At LED= 110mA)
[cd/m2 ]
280 350 -
Contrast Ratio 600 1000
Cross Talk (At 75Hz) [%] - -
Flicker [dB] - -
Optical Equipment: BM-5A, BM-7, PR880, or equivalent
document version 0.4
6/26
4
4
- 4
1.5 5
-20
7
Product Specification
Minimum
Luminance
of 9 points
=
Max
imum
Luminance
of 9 points
50 %
90 %
90 %
50 %
10 %
10 %
G170EG01 V1
AU OPTRONICS CORPORATION
ote 1: Definition of viewing angle
N
Vi
i
e
ngang
w
l
i
h
t
e
s
f
emeas
remen
u
t
t
o
con
ras
i
t
ra
10
t
o
h
tt
a
escreencen
,
t
er
o
,
180°h
era
v
i
l
d
t
or
on
a
z
an
180° vertical range (off-normal viewing angles). The 180° viewing angle range is broken down as follows;
90° (θ) horizontal left and right and 90° (Φ) vertical, high (up) and low (down). The measurement direction is
typically perpendicular to the display surface with the screen rotated about its center to develop the desired
measurement viewing angle.
Note 2: 9 points position
Note 3: The
minimum test point luminance
document version 0.4
luminance uniformity of 9 points is defined by dividing the maximum luminance values by the
δ
W9
7/26
TFT-LCD Module
LCD Panel
ote 4: Measurement method
N
Product Specification
AU OPTRONICS CORPORATION
G170EG01 V1
The LCD module should be stabilized at given temperature for 30 minutes to avoid abrupt temperature
change during measuring. In order to stabilize the luminance, the measurement should be executed after
lighting Backlight for 30 minutes in a stable, windless and dark room.
Photo detector
Field=2°
50 cm
Note 5: Definition of Cross Talk (CT)
CT = | YB – YA | / YA × 100 (%)
Where
YA = Luminance of measured location without gray level 0 pattern (cd/m2)
YB = Luminance of measured location with gray level 0 pattern (cd/m2)
Center of the screen
document version 0.4
8/26
Loading...