Studio Condenser
STUDIO CONDENSER MICROPHONE
CX-112
CX-112
OVERVIEW:
The CX-112, a large diaphragm condenser microphone with a
contemporary design and excellent performance characteristics, is an
exceptional tool for for professional audio production, project studios
and live stage performances. Delivering a smooth, uniform frequency
response from 20 Hz - 20 kHz, the CX-112 offers a rich, full bodied
sound delivered by its one-inch capsule.
The CX-112 is equipped with a bass roll-off lter to help eliminate
rumble and hum in the lower frequencies and a -10 dB pad to achieve
higher sound pressure levels without distortion.
A perfect candidate for a wide variety of acoustic instruments, the
CX-112 will handle vocals, string sections, guitar, ensembles, guitar
cabinets, ambient room miking and live stage.
The CX-112, which is designed with discreet low noise preamp circuitry,
operates on phantom power of 48-52 volts. Optimum results will be
achieved by using the CX-112 with a high quality mic preamplier and
premium quality microphone cable.
SUPPLIED ACCESSORIES:
Adjustable one piece metal clip (MC-112)
Foam-lined wood case (CASE-WOOD)
OPTIONAL ACCESSORIES:
WS-112 - External foam windscreen
APS-2 - Two-channel phantom power supply
PD-133 - Pop Diffuser
TRIPOD - Tripod Stand
SMT-CX112 - Isolation shockmount
MODEL VARIATIONS:
CX-112 MP - Matched stereo pair.
Allows for a wide variety of stereo miking techniques
FEATURES:
Gold-sputtered diaphragm
Low noise electronics
-10 dB pad and bass roll-off
Rich warm tones - ideal for digital recording
High power handling of 145 dB SPL
Adjustable metal clip allows for secure
positioning
APPLICATIONS:
Studio vocals, lead and backing
Voice over
Choir
Ambient room mic
Drum overheads
Orchestra
Bells, chimes, marimba, vibes
Acoustic instruments (piano, sax, strings,
guitar, flute)
Electric guitar cabs
CX-112 on SMT-CX112 MC112 PD133 with CX-112 APS-2
SPECIFICATIONS:
CX-112
Transducer Type Condenser
Capsule Technology 1.07”/27mm Gold Vapor Diaphragm
Frequency Range 20 Hz - 20 kHz (+/- 3 dB)
Polar Pattern Cardioid
Output Impedance 200 Ohms
Sensitivity 14 mV / Pa @ 1k
Noise Floor 18 dB (A weighted)
Signal to Noise Ratio 76 dB
Power Requirements 48-52 volts phantom
Maximum SPL ≥145 dB
Dynamic Range 127 dB
Cable/Connector 3 pin gold plated
male XLR connector
Polarity Positive pressure on diaphragm
produces positive voltage on pin 2
relative to pin 3 of output
XLR connector
Housing / Finish Brass /
Black satin
Weight 450 g / 16 ounces
Length 163 mm / 6.42 inches
ARCHITECTS AND ENGINEERS SPECIFICATIONS:
The microphone shall be of the condenser type with a cardioid polar pattern. The microphone shall operate
on 48-52 volts phantom power and the nominal output impedance shall be equal to 200 ohms at 1 kHz. The
microphone shall have a sensitivity of 14 mV / Pa and shall have a maximum SPL level of ≥145 dB with a THD
of 0.5% when the -10 dB pad is engaged. The microphone shall have a ne steel mesh grill and a brass body
50 mm in diameter and 163 mm in length. The microphone shall be the Audix CX-112.
OPERATION:
The CX-112 is a low impedance microphone and should be plugged into a “mic level” input on your console,
mixer, or recording device. The CX-112 requires phantom power and will NOT operate without phantom power
voltage (48 Volts recommended) which is available on most professional mic preamps and mixing devices. If
phantom power is not available on your equipment, you will have to procure a phantom power supply (such
as the Audix APS-2).
Avoid plugging or unplugging the microphone from a PA system unless the channel is muted or the volume of
the system turned down. Failure to do so may result in a loud “popping” noise which could seriously damage
the speakers in the PA system.
USER TIPS:
The correct side: Note that the front of the microphone element is on the same side as the printing. This side
of the microphone should be facing towards the sound source.
The Switches: The CX-112 is equipped with 2 slider switches that control the -10 dB pad and bass roll-off. They
are located directly above the Audix logo on the front of the mic.
-10 dB Pad: The -10 dB switch is located above the Audix logo and to the right. When the switch is all the way
to the left, (the 0 dB position), it is NOT engaged, and the mic is at its normal output level. The -10 dB pad allows
you to change the sensitivity (output level) of the microphone right at the capsule. This is much more effective
than padding the mic at the preamp stage at the console or mixing device. The net result is the ability to record
very high sound pressure levels before distortion.
Bass Roll-Off: This feature allows you to change the frequency response of the CX-112 and gently diminish
the bass response from 300 Hz and below. The bass roll-off (also referred to as “attenuation”) is the switch
on the left-hand side above the Audix logo. When the switch is all the way to the left (the “Flat” position), the
bass roll-off is NOT engaged. In some cases, you will want to roll-off or lter out the bass frequencies from
your recording or performance. These frequencies can be controlled by external EQ, however, the advantage
of having them on the microphone is it is much cleaner to control these frequencies at the capsule level. In the
case of live recording, the bass roll-off will help to eliminate unwanted boominess or rumble coming from other
instruments on the stage (for example, the bass and bass drum). In the case of a recording environment, it will
depend on the instrument or voice being recorded. The roll-off can help to eliminate plosives or popping from a
vocal or it may be utilized to clean up the excessive bass frequencies from certain instruments. In any case, it
is recommended to try “with” and “without” roll-off before making any nal decisions.
*Further miking techniques can be found on our website at www.audixusa.com
FREQUENCY / POLARS:
***All specications subject to change without notice.
SERVICE AND WARRANTY:
This microphone is under warranty for
a period of 3 years from any and all
manufacturing defects. Should your
microphone fail in any way, please
contact the Audix Service department
at 503-682-6933. A Return Authorization number is required before returning
any products.
CARE AND MAINTENANCE:
The CX-112 is manufactured to exacting
specs with roadworthy construction. However,
the capsule is highly sensitive and should be
handled with care. Avoid extreme temperatures
and be sure to store your microphone in the
pouch provided when not in use. Moisture of
any kind can adversely affect the sound and
performance of your microphone.
To register your
microphone, please visit
www.audixusa.com
DIMENSIONS (mm):
www.audixusa.com Call: 503-682-6933 Fax: 503-682-7114
Audix Corporation 9400 SW Barber Street, Wilsonville, OR 97070
Loading...