Microphone Table
ATS SERIES
ATS SERIES
OVERVIEW
The ATS1, ATS1LX and ATS1LP are the industry’s only programmable, shock absorbent
table stands with an LED indicator that does not require external power supplies,
eliminating the added expense and complication associated with installation and
wiring. The LED indicator and audio switching circuitry operate on the same phantom
power source supplied to the microphone. The result is simplified installation and
reliable operation. The base has programmable functions that are changed with a
simple, intuitive dip switch which can be set to operate in Toggle On, Toggle Off,
Momentary Talk and Momentary Mute modes. Also supplied within the base is a Low
Cut Filter offering additional protection from bass frequencies that may cause rumble
or hum. The ATS1LX and ATS1LP can be further programmed to operate seamlessly
with automated teleconferencing and switch systems in external logic control mode.
Stand Accessory
The ATS is manufactured with a precision die cast zinc alloy base, durable black E-coat
finish, LED indicators and a noise free mechanical switch.
MODEL VARIATIONS
ATS10 - Table stand with latching on/off switch
ATS 1 - Heavy-duty shock absorbent table stand with 3 XLR connector,
programmable switch (on/off, talk/mute) and choice of two connector versions:
. ATS1LP - 5-pin terminal connector located inside the base
. ATS1LX - 5-pin XLR output connector located at the back of the base
OPTIONAL ACCESSORIES
ADX Series - ADX12, ADX18
MG Series - MG12HC, MG15HC, MG18HC
MGN Series - MGN6, MGN12, MGN29
MicroPod - MicroPod6, MicroPod6HC, MicroPod12, MicroPod12HC, MicroPod18,
MicroPod18HC, MicroPod6S, MicroPod6WS
FEATURES
. Heavy duty die cast base provides stability
. Shock mount design limits touch noise and
vibration
. Four programmable talk-mute functions
. Local remote control function settings
. Seamless integration with automated mixers
(ATS1LX & ATS1LP)
. Designed, assembled & tested in the USA
. 1 year warranty
APPLICATIONS
. Podium
. Lectern
. Video conferences
. Classrooms
. Courtrooms
ATS WITH OPTIONAL MIC
. Boardrooms
CLOSE UP
3-PIN XLRm OUTPUT
BOTTOM
SPECIFICATIONS
Mic Input Connector
Base Output Connector
Switch
Off (mute) attenuation
Power Requirements
Finish
Length
Width
Height
Weight
Closure I/O voltage
LED input
Closure through current
On resistance
1/O leakage current
ATS10 ATS1 ATS1LP ATS1LX
3-pin XLRf
3-pin XLRm 3-pin XLRm 5-pin Terminal Block 5-pin XLRm
Latching on/off
11-52 V phantom DC
2mA typical
- - 5 to 30 V on pin 5
- - LED ON when 0 - 0.4 V DC is on pin 5
- - 200 mA
- - >10 ohms
- - 1uA
Programmable on/off,
talk/mute
45dB minimum
36-52 V phantom DC
2mA typical
160 mm / 6.9 in
124 mm / 5.9 in
Programmable with remote capabilities
36-52 V phantom DC 2mA typical
Matte Black
45 mm / 1.8 in
1.4 kg / 3 lbs
LED OFF when 5 - 30 V DC is on pin 5
ATS SERIES
TTL
Compatible
DIMENSIONS (mm)
SWITCH SETTINGS
Setting Dip Switches
Low Cut Filter Switch
OPERATION
Connecting the Gooseneck Microphone - Align the connector of the microphone to the
XLR pins on top of the base. Gently push down until the connectors “click” into place.
Important: The microphones will require phantom power to operate. This may be supplied
to the microphone from either the mixing console or a phantom power supply.
Setting Dip Switch - Low Cut Filter: Inside the base, locate the switch on the PCB labeled
“Low Cut Filter.” The filter provides protection from bass frequencies that may cause rumble,
hum, or vibration by eliminating frequencies <100 Hz. To engage, push the dip switch to the
“on” position.
Removing the Microphone - Press the release tab on the top of the base to remove the
microphone.
Connecting Audio and Logic - Use a balanced microphone cable and connect into the
back side of the ATS base until it “clicks” into place. To disconnect, press the tab on the
microphone cable XLRf connector and remove from base.
SWITCH SETTINGS
(Logic) External Control
Momentary Mode
Push to Mute
Off
E = External Control
The top dip switch is set to the left
allowing the button to be controlled
remotely by the DSP module.
Local Control
Toggle Mode
Push to Talk
On
L = Local Control
The top dip switch is set to the right
allowing the button to be activated
manually by the user at the base.
PRODUCT REGISTRATION: Please register your product online at www.audixusa.com/docs_12/about/product_registration.shtml.
SERVICE AND WARRANTY:
workmanship, Audix will repair or replace said product at no charge with proof of purchase. Audix does not pay or reimburse shipping costs for warranty repairs or returns. The warranty excludes
any causes other than manufacturing defects, such as normal wear, abuse, environmental damage, shipping damage or failure to use or maintain the product per the supplied instructions. No
Implied Warranties: All implied warranties, including but not limited to implied warranties of merchantability and fitness for a particular purpose are hereby excluded. The liability of Audix, if any,
for damages relating to allegedly defective products shall be limited to the actual price paid by Dealer for such products and shall in no event include incidental or consequential damages of
any kind. Should your microphone fail in any way, please contact the Audix Service department at 503.682.6933. A Return Authorization is required before returning any product. OTHER THAN
THIS WARRANTY, AUDIX MAKES NO WARRANTIES, EXPRESS OR IMPLIED, WITH RESPECT TO THE PRODUCTS, THE USE OF THE PRODUCTS, THE PERFORMANCE OF THE PRODUCTS. AUDIX SHALL
NOT BE LIABLE FOR SPECIAL INCIDENTAL, CONSEQUENTIAL, INDIRECT OR SIMILAR DAMAGES ARISING FROM OR BASED ON THE SALE, USE, STORAGE OR DISPOSAL OF THE PRODUCTS, AUDIX’S
SERVICE WORK, BREACH OF WARRANTY, BREACH OF CONTRACT. NEGLIGENCE, OR ANY OTHER THEORY OF LIABILITY, EVEN IF AUDIX HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
ALL SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.
These product is under warranty for a period of 1 year to be free of defects in material and workmanship. In the event of a product failure due to materials or
www.audixusa.com
Audix Corporation 9400 SW Barber St. Wilsonville, OR 97070
503.682.6933 Fax: 503.682.7114
ver 3.0 10-15
Loading...