Model APS-410
Owner’s Manual
4 Button Remote Security System
with Dual Stage Shock Sensor
IMPORTANT !
system is equipped with selectable manual override circuitry. It is possible that you will need to
manually override your security system if the transmitter becomes lost, or inoperative due to
battery failure. Reading the sections on "MANUALLY OVERRIDING YOUR SYSTEM" is
necessary to fully understand the procedure required to enable your vehicle in such situations.
In addition, the chart on the last page of this manual has a section for the particular features and
options installed in your vehicle as well as the override method selected.
override is pre-selected from the factory,
Code" operation. Confirm the override mode selected on the last page of this manual and
familiarize yourself with the selection on it's operation.
FEATURES :
w 2 Four Button Programmable RF Transmitters (capable of accepting 4 transmitters)
w Four Channel Receiver
w Anti Code Grabbing Technology
w Selectable Manual Override Mode
w Remote Panic in all modes
w Protected Valet
w User Programmable Manual Override Code
w 7 Function LED (Light Emitting Diode) - Arm / Disarm / Zone 1, 2, 3 / Valet / Arming
w Intrusion Alert with Memory
w Audible Arm / Disarm / Defective Zone / Tamper Confirmation
w Instant Siren Activation
w Starter Disable (Optional relay required)
w Additional Engine Immobilizer Output (optional relay required)
w True Last Door Arming (hardwire only)
w Defective Zone By-Pass
w Hardwire or Voltage Sense Selectable
w Active or Passive Arming Selectable
w Programmable Auto Lock On / Off
w Programmable Auto Unlock On / Off
w Programmable Door Lock Pulse Duration 1 Second / 3.5 Seconds /1 Sec L/ Dbl. U/L
w Programmable Active or Passive Door Locks
w User Programmable Permanent Chirp Delete
w On Command RF Chirp Delete from Transmitter
w 6 Tone Multi-Tone Siren
w RF Inhibit with ignition on
w Parking Light Flasher
w Plug In Dual Stage Shock Sensor
OPTIONS :
w Starter Disable
w Remote Trunk Release (must have electronic trunk release)
w Remote Keyless Entry (must have power door locks)
w Multiple Vehicle Capable
w Remote Starter
w Remote Power Window Roll Up
w Remote Garage Door Interface
w Two Step Unlock Configurable
In order to provide the highest possible level of security to your vehicle, this
however, the system can be configured for "Custom
Valet Switch manual
YOUR “ANTI CODE GRABBING” TRANSMITTERS
The transmitters included with your new security system use the most advanced
and secure form of radio frequency transmission available on any current
automotive security system. Some of today’s sophisticated auto thieves use a
device known as a code grabber, which will receive and store the signal from your
keychain transmitter, and re transmit at a later time to disarm your system.
Your anti code grabbing transmitters will change their signal every time the button
is pressed, so when a thief grabs the retransmits your signal, the alarm system
will not
respond.
If your transmitter button is pressed more than fifty times while it is out of range of
the vehicle (children playing with your keys), the transmitter will not operate when
you return to the vehicle, and will need to be re aligned to the receiver. To do this,
simply press the lock button two times within a one second time period. The
system will now respond to that transmitter each time a button is pressed.
NOTE: Your system has the option of using a siren, the vehicle horn, or both for the
sounding device. Where the siren is referenced below, the horn or both may in
fact chirp or beep.
ARMING THE SYSTEM - ACTIVE
1. Turn off the engine, exit the vehicle, and close all doors, hood lid, and trunk lid.
2. Press and release the Lock button on the keychain transmitter.
þ Red dash mounted LED begins to flash slowly.
þ Parking Lights flash one time.
þ Siren sounds one chirp.
If the siren sounds 3 chirps, then you have left a door, trunk, or
hood ajar. Simply close the opened entry point to provide full
protection. If the siren did not sound when arming, then the chirps
have been turned off, and you should refer to the section titled
‘’ELIMINATING THE ARM / DISARM CHIRPS’ ’ in this manual.
o Doors Lock - Optional
SILENT ARMING - ACTIVE
1. Turn off the engine, exit the vehicle, and close all doors, hood lid, and trunk lid.
2. Press and hold the lock button on the keychain transmitter for 2 seconds.
þ Red dash mounted LED begins to flash slowly.
þ Parking Lights flash one time.
þ Siren will not sound.
If the siren sounds 3 chirps, then you have left a door, trunk, or
hood lid ajar. Simply close the opened entry point to provide full
protection.
o Doors Lock - Optional
ARMING THE SYSTEM - P ASSIVE ( AUTOMA TIC )
1. Turn off the engine, exit the vehicle, and close and lock all doors, hood lid, and
trunk lid.
Page 2
þ Red dash mounted LED begins to flash rapidly, indicating 30 second
passive arming has begun.
2. Opening any protected entry point during the 30 second passive arming cycle
will immediately suspend automatic arming, and the 30 second passive
arming cycle will restart when all doors are closed. At the end of the passive
arming cycle;
þ Red dash mounted LED begins to flash slowly.
þ Parking Lights flash one time.
þ Siren sounds one chirp
If the siren did not sound when arming, then the chirps have
been turned off, and you should refer to the section titled
“ELIMINATING THE ARM / DISARM CHIRPS“ in this manual.
o Doors Lock - Optional
Door locking during passive arming is a selectable feature.
The alarm can be programmed to allow the doors to lock only
when arming using the keychain transmitter, and they will not
automatically lock during passive arming.
PROTECTION WHILE THE SYSTEM IS ARMED
þ Opening any protected door, hood, or trunk lid will cause the alarm to
immediately sound. The alarm will continue to sound for 30 seconds, then
stop and continue to monitor all protected entry points. If the thief left a door
opened, the alarm will sound for six 30 second cycles, remain armed and
ignore that triggered zone.
þ Whenever the system is armed, the red dash mounted LED indicator will
slowly flash. This serves as a visual deterrent to the potential thief. The
LED is a very low current bulb, and will not cause the vehicle’s battery to
drain, even when left unattended for extended periods.
þ Whenever the system is triggered, the vehicle’s parking lights will flash for
the full 30 second alarm cycle, attracting visual attention to the vehicle.
o Optional - Whenever the system is armed, the vehicle’s starting circuit will
be bypassed. If the thief should choose to ignore the siren, the vehicle can
not be started.
þ Any mild impact to the vehicle’s glass will cause the alarm to sound a short
series of warning tones.
þ Any strong impact to the vehicle’s glass will cause the alarm to trigger for
the full 30 second alarm cycle.
DISARMING THE SYSTEM
1. As you approach the vehicle, press and release the Unlock button on the
keychain transmitter.
þ Red dash mounted LED turns off.
If passive arming was selected during the installation, then the
Page 3