Audio-Technica ATM510 Datasheet

ATM510

Cardioid Dynamic Handheld Microphone

Features

• Natural, full-range vocal reproduction

• Superior anti-shock engineering ensures low handling noise and quiet performance

• Hi-ENERGY® neodymium magnet for improved output and transient response

• Excellent off-axis rejection for minimum feedback

• Cardioid polar pattern reduces pickup of sounds from the sides and rear, improving isolation of desired sound source

• Multi-stage windscreen effectively controls popping, distortion from sibilant sounds and wind noise

• Rugged all-metal design and construction for years of trouble free use

• Corrosion-resistant contacts from gold-plated XLRM-type connector

• Quiet-Flex™ stand clamp provides silent, exible microphone positioning

Description

The ATM510 is a dynamic microphone with a cardioid polar pattern. It is designed specically for close-up vocal use in professional live-sound applications.

The cardioid polar pattern of the microphone is more sensitive to sound originating directly in front of the element, making it useful for controlling feedback, reducing pickup of unwanted sounds and providing isolation between performers.

The output of the microphone is a 3-pin XLRM-type connector.

The microphone is enclosed in a rugged housing. Its multi-stage windscreen effectively controls popping, distortion from sibilant sounds and wind noise. The included AT8470 Quiet-Flex™ stand clamp permits mounting on any microphone stand with 5/8"-27 threads. A soft protective pouch is also included.

Operation and Maintenance

Output is low impedance (Lo-Z) balanced. The signal appears across Pins 2 and 3; Pin 1 is ground (shield). Output phase is “Pin 2 hot”— positive acoustic pressure produces positive voltage at Pin 2.

To avoid phase cancellation and poor sound, all mic cables must be wired consistently: Pin 1-to-Pin 1, etc. For a high-impedance (Hi-Z) mic input, connect a Lo-Z balanced cable to a Hi-Z matching transformer at the equipment input.

artist series live sound microphones

When using the microphone in settings with a stage monitor speaker, the speaker should be located 180° off axis (at the rear of the microphone). This placement, in conjunction with the microphone’s uniform cardioid pickup pattern, will virtually eliminate the possibility of undesired audio feedback.

Take care to keep foreign particles from entering the windscreen. An accumulation of iron or steel lings on the diaphragm, and/or foreign material in the windscreen’s mesh surface, can degrade performance.

Architect’s and Engineer’s Specications

The microphone shall be a moving coil dynamic designed for handheld or stand use. It shall have a cardioid polar pattern with a uniform 120° angle of acceptance and a frequency response of 90 Hz to 16,000 Hz. Nominal open-circuit output voltage shall be 1.7 mV at 1V, 1 Pascal. Output shall be low impedance balanced (300 ohms).

The output of the microphone shall be a 3-pin XLRM-type connector.

The microphone shall be 170.0 mm (6.69") long and have a head diameter of 53.7 mm (2.11"). Weight shall be 258 grams (9.1 oz). The microphone shall include a stand clamp and a soft protective pouch.

The Audio-Technica ATM510 is specied.

Specications

Element

Polar pattern

Frequency response

Open circuit sensitivity

Impedance

Weight

Dimensions

Output connector

Audio-Technica case style

Accessories furnished

In the inter est of standards devel opment, A.T.U.S.

offers full details on its test me thods to other industr y

1 Pascal = 1 0 dynes/cm

Specication s are subject to chang e without notice.

professional s on request.

= 10 microb ars = 94 dB SPL

frequency response: 90 –16,000 Hz

100

12" or more on axis

330˚

200

Frequency in Hertz

0˚

180˚

500

30˚

150˚

60˚

120˚

10k

90˚

LEGEND

200 Hz

1 kHz 5 kHz 8 kHz

LEGEND

polar pattern

300˚

270˚

240˚

210˚

SCALE IS 5 DECIBELS PER DIVISION

Dynamic Cardioid 90-16,000 Hz –55 dB (1.7 mV) re 1V at 1 Pa 300 ohms 258 g (9.1 oz)

170.0 mm (6.69") long,

53.7 mm (2.11") maximum diameter Integral 3-pin XLRM-type T6 AT8470 Quiet-Flex™ stand clamp for

/8"-27 threaded stands; 5/8"-27 to 3/8"-16

threaded adapter; soft protective pouch

10 dB

Response in dB

20k