Audio-Technica AT-LP60XBT-USB User Manual

AT-LP60XBT-USB

User Manual

Automatic Wireless Turntable

AT-LP60XBT-USB

Introduction

Thank you for purchasing this Audio-Technica product.
Read through this user manual before using the product to ensure its correct use. Also, keep this manual for future reference.

This product can be used only in the countries where the product is sold. Make sure that the operating voltage and the plug of AC
adapter of the product are correct for the country you live in.

Package contents

Make sure that you have all the included items listed below before using this product.
If some items are missing or damaged, contact your local Audio-Technica dealer.

•

Turntable body

•

45 RPM adapter

•

Felt mat

•

RCA audio cable

•

Platter (with drive belt)

•

USB cable (approx. 1.9 m (6.2'))

(approx. 1.2 m (3.9'))

•

AC adapter (approx. 1.5 m (4.9'))

•

Quick start guide

•

Caution guide

After purchase, we suggest that you save all packaging materials for possible future storage, moving, or shipping.

1

Safety precautions

Although this product was designed to be used safely, failing
to use it correctly may result in an accident. To ensure safety,
observe all warnings and cautions while using the product.

Important information

Warning:

To prevent fire or shock hazard, do not expose this apparatus
to rain or moisture.

Caution:

•

Do not expose this apparatus to drips or splashes.

•

To avoid electric shock, do not open the cabinet.

•

Refer servicing to qualified personnel only.

•

Do not expose this apparatus to excessive heat such as
sunshine, fire or the like.

•

Do not subject this apparatus to strong impact.

•

This apparatus should be located close enough to the AC
outlet so that you can easily grasp the AC adapter at any time.

•

In case of emergency, disconnect the AC adapter quickly.

•

Do not place any objects filled with liquids, such as vases, on
this apparatus.

•

To prevent fire, do not place any naked flame sources (such
as lighted candles) on this apparatus.

•

Do not install this apparatus in a confined space such as a
bookcase or similar unit.

•

Install this apparatus only in the place where ventilation is good.

For customers in the USA

FCC Notice

Warning:

This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may
cause undesired operation.

Caution:

You are cautioned that any changes or modifications not
expressly approved in this manual could void your authority to
operate this equipment.

Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of
the following measures:

– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for

help.

RF Exposure Statement:

This transmitter must not be co-located or operated in
conjunction with any other antenna or transmitter used in other
systems. This device complies with FCC radiation exposure
limits set forth for an uncontrolled environment and meets the
FCC radio frequency (RF) Exposure Guidelines. This equipment
has very low levels of RF energy that it deemed to comply
without maximum permissive exposure evaluation (MPE). But it
is desirable that it should be installed and operated keeping the
radiator at least 20 cm or more away from person’s body.

Contact:

Responsible Company: Audio-Technica U.S., Inc.
Address: 1221 Commerce Drive, Stow, Ohio 44224, USA
Tel: [phone]

For customers in Canada

IC statement:

CAN ICES-3 (B)/NMB-3(B)

This device complies with INDUSTRY CANADA R.S.S. 247.
Operation is subject to the following conditions: (1) This
device may not cause harmful interference and (2) this device
must accept any interference received, including interference
which may cause undesired operation. Under Industry Canada
regulations, this radio transmitter may only operate using an
antenna of a type and maximum (or lesser) gain approved for
the transmitter by Industry Canada. To reduce potential radio
interference to other users, the antenna type and its gain
should be so chosen that the equivalent isotropically radiated
power (e.i.r.p.) is not more than that necessary for successful
communication. This equipment should be installed and
operated with minimum distance 20 cm between the radiator &
your body.

2

Notes on use

Turntable body

•

Do not set and use the product in locations that are
considerably hot or humid, dirty, or subject to extreme
vibrations.

•

The product should be positioned on a flat, level surface.

•

When closing the dust cover, close it completely. Do not open
the dust cover during playback.

•

Read the user manual for the Bluetooth receiver device.

Cartridge

•

Attach the provided protector to the cartridge when the
product is not in use.

•

Do not touch the stylus of the cartridge with your finger.

•

Do not allow the stylus to bump against the platter, felt mat,
or edge of the record.

3

Part names and functions

12

7

7

1

2

8

3

9

10

4

5
6

11

AT-LP60XBT-USB

13 14 1715 1816 20

45 RPM adapter (shown in receptacle)

1

Adapts 7" records with large center holes to fit center
spindle.

Platter

2

Spindle

3

Felt mat

4

Indicator LED

5

Displays the Bluetooth connection status by blinking/
lighting.

Wireless function button

6

Use to connect the product to a Bluetooth® device.

Dust cover hinge holders

7

Attachment points for dust cover hinges.

Tonearm

8

Tonearm rest

9

Headshell and cartridge

10

The cartridge (AT3600L) is attached to the headshell.

Size selector

11

Switch between 12" and 7", according to the size of the
record.

19

Dust cover

12

Platter speed button

13

Select the platter speed (33-1/3 or 45 RPM).

START button

14

Spins the platter and moves the tonearm.

STOP button

15

Returns the tonearm to its original position and stops the
platter.

Tonearm lift button

16

Lifts and lowers tonearm for manual selection.

Pre-amplifier selector switch

17

If using an amplifier with a PHONO input jack, set this
switch to the PHONO position. If connecting to the AUX
jack of an amplifier, set this switch to the LINE position.

Stereo output terminals

18

Connect the RCA audio cable.

USB output

19

Use this output to connect your turntable to the USB input
of your computer.

Power input jack

20

Connect the AC adapter.

4

Preparation for use

Installing the turntable

•

Mount the product on a level surface.

•

To avoid the effects of vibrations and acoustic pressure, do
not mount the product next to such items as speakers.

•

The product may pick up radio static if placed next to a radio.
Therefore, try to keep the product away from radios.

•

If the product is near equipment (cell phone, etc.) that emits
strong radio waves, noise may occur.

AT-LP60XBT-USB

AT-LP60XBT-USB

Installing/removing the dust cover

When removing the dust cover, slowly pull the dust cover out
from the dust cover hinge holders. When attaching the dust
cover, insert the hinges of the dust cover into the two dust
cover hinge holders on the back of the body.

2. Place the belt on the motor pulley (brass-colored).

•

Align one of the platter openings with the brass motor
pulley, and, while pulling both ends of the red ribbon that
comes attached to the belt, place the belt on the motor
pulley, as per the diagram. When doing this, be careful not
to twist the belt.

Red ribbon

Belt

Motor pulley
(brass-colored)

Straight Twisted

3. Remove the red ribbon from the belt.

Hinge

Assembling the product

This product requires some assembly before using it for the
first time.
Do not connect the AC adapter until assembly is complete.

1. Set the platter on the spindle.

•

Make certain that the platter is fully seated on the spindle.

Opening Platter

Motor pulley

(brass-colored)

4. Set the felt mat on the platter.

•

After setting the felt mat, put the 45 RPM adapter into the
space made for it on the upper left.

45 RPM adapter

Felt mat

AT-LP60XBT-USB

Spindle

AT-LP60XBT-USB

5