Audio Technica ATH-S700BT Instruction Booklet
Manuel d'utilisateur
Instruction booklet
Libretto di istruzioni
ATH-S700BT
ATH-S700BT
Casque sans l
ATH-S700BT
Wireless headphones
ATH-S700BT
Auriculares inalámbricos
CAUTIONS
English
Please read these cautions before using your headphones.
To ensure safety, observe all cautions while using this equipment.
Thank you for purchasing these wireless stereo headphones.
Please keep this manual handy so they are always available for reference.
2
For customers in the USA
FCC Notice
Warning
This device complies with Part 15 of theFCC Rules. Operation is subject to thefollowing two
conditions: (1)This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Caution
You are cautioned that any changes or modifications not expressly approved in this manual could void
your authority to operate this equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
− Reorient or relocate the receiving antenna.
− Increase the separation between the equipment and receiver.
− Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
− Consult the dealer or an experienced radio/TV technician for help.
For customers in Canada
IC statement
This device complies with INDUSTRY CANADA R.S.S. 210, en conformité avec IC: RSS-210/CNR210.
Operation is subject to the following conditions: (1) This device may not cause harmful interference
and (2) this device must accept any interference received, including interference which may cause
undesired operation.
CAN ICES-3 (B)/NMB-3(B)
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type
and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio
interference to other users, the antenna type and its gain should be so chosen that the equivalent
isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
●
If battery uid gets into eyes, do not rub them.
Rinse thoroughly with clean water such as tap water and consult a doctor immediately.
●
If battery uid leaks, do not touch uid with bare hands.
- If uid remains inside this product, it may cause malfunction. If battery uid leaks, please contact
our service center.
- If uid gets in your mouth, gargle thoroughly with clean water such as tap water and consult a
doctor immediately.
- If your skin or clothing comes in contact with uid, immediately wash the affected skin or clothing
with water. If you experience skin irritation, consult a doctor.
●
Never heat, disassemble or modify the battery, nor dispose of it in a re.
Failure to observe this caution could cause leakage, generation of heat or explosion.
CAUTIONS
English
Caution for rechargeable battery
●
Do not use the headphones within 22 cm of where a cardiac pacemaker is installed.
Pacemakers may be affected by radio waves of the headphones.
●
Do not use the headphones near medical equipment.
Radio waves may affect cardiac pacemakers and medical electronic equipment. Do not use the
product inside medical facilities.
●
Do not use the headphones in aircrafts.
Radio waves may affect electronic equipment and cause accidents due to malfunction.
●
Do not use the headphones near automatic control devices such as automatic doors and re
alarms.
Radio waves may affect electronic equipment and cause accidents due to malfunction.
●
Do not disassemble, modify or attempt to repair the headphones.
●
Do not subject the headphones to strong impact.
●
Do not expose this apparatus to drips or splashes, and do not handle with wet hands to avoid
electric shock or malfunction.
●
Disconnect this product from the computer if you encounter any malfunction like noise, smoke,
smell, heat or damage with the product. In such case, contact your local Audio-Technica dealer
or service center.
●
This apparatus should be located close enough to the AC outlet so that you can easily grasp the
power cable plug at any time.
●
Do not expose this apparatus to drips or splashes.
●
Do not cover with a cloth.
●
Follow applicable laws regarding mobile phone and headphone use if using headphones while
driving.
●
Do not use the headphones in places where the inability to hear ambient sound presents a
serious risk (such as at railroad crossings, train stations, and construction sites).
●
To prevent damage to your hearing, do not raise the volume too high. Listening to loud sound
for an extended period may cause temporary or permanent hearing loss.
●
Discontinue use if skin irritation results from direct contact with the product.
●
Be careful to avoid pinching yourself between the housing and yoke of the product.
3
●
If battery uid gets into eyes, do not rub them.
Rinse thoroughly with clean water such as tap water and consult a doctor immediately.
●
If battery uid leaks, do not touch uid with bare hands.
- If uid remains inside this product, it may cause malfunction. If battery uid leaks, please contact
our service center.
- If uid gets in your mouth, gargle thoroughly with clean water such as tap water and consult a
doctor immediately.
- If your skin or clothing comes in contact with uid, immediately wash the affected skin or clothing
with water. If you experience skin irritation, consult a doctor.
●
Never heat, disassemble or modify the battery, nor dispose of it in a re.
Failure to observe this caution could cause leakage, generation of heat or explosion.
CAUTIONS
PRECAUTIONS
English
●
Be sure to read the operation manual for the
Bluetooth
device before use.
●
Audio-Technica will not be liable in any way for any loss of data in the unlikely event that such
losses should occur while using this product.
●
On public transport systems or in other public places, keep the volume low so as not to disturb
other people.
●
Please minimize the volume on your audio device before connecting the headphones in order to
avoid hearing damage from sudden exposure to excessive volume.
●
When using this product in a dry environment, you may feel a tingling sensation in your ears. This
is caused by static electricity accumulated on your body, not by a headphone malfunction.
●
Do not store the headphones under direct sunlight, near heating devices or in a hot, humid or
dusty place. Do not allow the headphones to get wet.
●
When this product is used for a long time, the headphones may become discolored due to
ultraviolet light (especially direct sunlight) or wear.
●
The cable may become caught or severed if product is placed in a bag or pocket without adequate
protection. Always store the product in the included pouch.
●
Connect/disconnect the cable by holding the plug. Pulling directly on the cable can result in a
broken wire and the risk of electric shock. Be sure to disconnect the USB cable from the
headphones and store it in the attached pouch.
●
Reception on the headphones is available only through the mobile telephone network.
Please note that performance of other types of phone reception (phones using other wireless
applications) cannot be guaranteed.
●
If you use the headphones close to an electronic device or transmitter (such as a mobile phone), a
noise may be generated in the headphones. In this case, keep headphones away from the
electronic device or transmitter.
●
If you use the headphones near a TV or radio antenna, noise may be generated in the television or
radio. In this case, keep headphones away from the TV or radio antenna.
4
●
Do not attempt to pierce with a nail, hit with a hammer or step on the battery.
Failure to observe this caution could cause generation of heat, damage or ignition.
●
Do not drop the battery or subject it to strong impact.
Failure to observe this caution could cause leakage, generation of heat or explosion.
●
Do not use, leave or store the battery in the following places:
■
Area exposed to direct sunlight or high temperatures and humidity
■
Inside of a car under the blazing sun
■
Near heat sources such as heat registers
Failure to observe this caution could cause leakage, generation of heat, explosion or performance
degradation.
●
Do not get the battery wet.
Failure to observe this caution could cause generation of heat, explosion or ignition.
●
Charge only with the included (specied) USB cable.
Failure to observe this caution could cause malfunction or re.
●
After using the device, be sure to switch it off.
Leakage often occurs due to battery drain that results from a failure to switch off device.
PRECAUTIONS
Cleaning
English
●
For long-time storage, keep the headphones in a well-ventilated place without high temperatures and
humidity.
●
The earpads deteriorate over time due to use or storage. For information about replacing headband pads
or other parts, or for information about other serviceable parts, contact your Audio-Technica dealer or
service center.
Get into the habit of regularly cleaning your headphones to ensure that they will last for a long time.
Do not use alcohol, paint thinners or other solvents for cleaning purposes.
●
Cleaning the headphones/remote control with microphone.
Wipe the main unit with a dry cloth.
●
About cables.
Wipe your cables with a dry cloth after use if there is sweat or other dirt present. Using an unclean cable
continuously will deteriorate and harden the cable, resulting in headphone malfunction.
●
About plugs on cables.
Wipe your plug with a dry cloth if dirty. Using the plug without cleaning it can cause sound skipping or
distortion.
●
Cleaning the earpads and headband.
To clean, wipe with a dry cloth. Earpads and headband may fade if sweat or water dries on them. If the
earpads and headband get wet, we recommend wiping them with a dry cloth and allowing them to dry in
the shade.
●
To protect the built-in rechargeable battery, charge it at least once every half year.
If you leave it too long, you will have less rechargeable battery life or the battery may not recharge
at all.
●
Do not use cords and cables other than the supplied one. Doing so can result in malfunction.
Simultaneous use with other devices
Failure, such as the interruption of sound, may be caused by radio wave interference from devices that use
the same frequency band (2.4GHz) as the headphones, including
Bluetooth
-enabled devices, devices
using wireless LAN, digital cordless phones and microwaves. Similarly, because radio waves of the
headphones may affect these devices, take the following precautions:
-
Install the devices using the same frequency band (2.4GHz) away from the headphones.
- Do not use the product in hospitals, trains and aircrafts.
Instructions for Use
Any device which is connected to the headphones needs to meet the
Bluetooth
standards established by
Bluetooth SIG and be certied.
Even if the device meets the
Bluetooth
standards, it might not connect to the headphones or the operation
method and behavior may differ depending on the device's characteristics and specication.
5
Part names and functions
English
Battery jack
●With the cap open (left-side housing)
*The cap cannot be fully removed.
Reset
button
Microphone
Earpads
Cap
Slider
Multifunction button
Headband
Yoke
Swivel
Housing
Use to make calls
on the
headphones
Close the cap when not
using any of the jacks.
Connect the attached USB
charging cable to charge.
Headphone jack
Connect the included cord for
smartphones to use the play-through
function.
Turns up the volume.
Use for a variety of operations such as turning the
power on and off, playing music and answering calls.
Volume button (+)
Displays the operating status of the
headphones.
Indicator
Turns down the volume.
Volume button (−)
6
LEFT/ R IGHT
How to Connect
How to Charge
English
Computer
USB port
USB charging cable (included)
Micro USB terminal
Type A
Battery
jack
1
Connect the included USB cable (the micro USB
terminal side) to the headphone battery jack.
Flashes blue twice: Charging just started
Lit red: Charging
Off: Charging complete
2
Connect the USB cable (the Type A side) to the computer and start charging.
3
During charging, the indicator turns on/ashes as follows:
Fully charge the battery when using for the rst time.
When the rechargeable battery power runs low, you will hear a short beep and the indicator will
ash red. When you hear the beep, charge the battery.
It takes about 3 hours to charge the battery fully. (It varies depending on service conditions.)
* The headphones cannot be used during charging because
Bluetooth
is disconnected.
To connect the headphones to a
Bluetooth
device, the headphones need to pair (register) with the
device. Once they are paired, you don't need to pair them again.
However, you will need to pair again in the following cases:
・
If the headphones are deleted from the
Bluetooth
device connection history,
・
If the headphones are sent out for repair,
・
If the headphones are paired with 9 devices or more.
(The headphones can be paired with up to 8 devices. When you pair with a new device after pairing
with 8 devices, pairing information for the device with the oldest connection date will be overwritten
by information for the new device.)
About Pairing
* The included USB cable is specically designed to charge the headphones.
Data cannot be transferred to and from computer.
7
How to Connect
English
ATH-S700BT
Device
ON
* Read the user manual for the
Bluetooth
device.
* Place the
Bluetooth
device within 1 meter of the headphones to perform pairing correctly.
* Wear the headphones to conrm pairing by listening for sound.
How to Perform Pairing
1
Starting with the headphones turned off, press and
hold the Multifunction button for about 4 seconds,
and then release when the indicator ashes red and
blue.
3
When the headphones are searched for,
"ATH-S700BT" will display on the Bluetooth device.
Select "ATH-S700BT" and register the device to be
connected.
Some devices may ask for passkey*.
In this case, enter "0000".
4
When the headphones ring, the pairing has
performed normally and been successfully
completed.
* The passkey is also called passcode, PIN code, PIN number
or password.
* For more information on how to use the
Bluetooth
device, read the operation manual for the
device.
2
Pairing process will begin and the Bluetooth device will search for the headphones.
Press and
hold
8
Short beep
♪
Beep sound
♪
Select
How to Use
About Indicator Display
English
Waiting to be
connected
Remaining battery
level low
Remaining
battery level
The indicator of the headphones displays the following operating status by ashing or turning on.
Operating status
Searching for device
Pairing
Connect
Charge
A2DP/AVRCP link or
HFP/HSP link is connected
Full charge
Charging error
LED display patterns
Flashing
Lit
Flashing
Off
Charging
BlueRed
ON : Press and hold the Multifunction button (for about 2
seconds) to turn on the power.
The headphones are capable of making
Bluetooth
connections, playing music and receiving
incoming calls. Please use the headphones in accordance with applications. Please note
that we cannot guarantee the operation of applications of the
Bluetooth
device.
OFF : When the power is on, press and hold the Multifunction
button (for about 2 seconds) to shut off the power.
Power supply
Long press
9
Beep sound
(Indicator: blue/blue/red)
♪
Beep sound
(Indicator: red/red)
♪
How to Use
English
Place the headphones on your head so that the
“LEFT”side is on your left ear and “RIGHT” side is
on your right ear, and adjust them so that the
earpads cover your ears completely.
How to Wear
1
To connect for the rst time, refer to “How to Connect” and pair the headphones with a
Bluetooth device and connect.
Once pairing has been performed, turn on the headphones and turn on the Bluetooth
connection of the Bluetooth device.
2
Play and enjoy music according to the operation manual of the Bluetooth device
connected. The following operations are available on the headphones:
Listening to Music
Slider
Play/Pause Plays or pauses music
Short press
Forward Forwards to the next track.
2 consecutive
short presses
Rewind Returns to the previous track.
3 consecutive
short presses
Fast-forward
The currently playing track is fastforwarded while the button is held down.
Short press,
long press (2nd
press is a long press)
Fast-rewind
The currently playing track is rewound
while the button is held down.
2 consecutive
short presses,
long press (3rd
press is a long press)
Multifunction button
Volume Up
You will hear a beep when the volume
reaches its maximum.
+
button
Volume Down
You will hear a beep when the volume
reaches its minimum.
*Audioisnotmutedevenifitisreducedto
theminimumvolume.
-
button
Volume button
10
How to Use
English
Taking a Call
When you hear the ringtone, briey press the Multifunction button and take the call.
Taking a call
During the call, briey press the Multifunction button to end the call.
Ending a call
During an incoming call, press and hold the Multifunction button (for about 2 seconds) to reject the
incoming call.
Blocking communications
Every time you press and hold the Multifunction button (for about 2 seconds*) during a call, you will
toggle between accessing the call via the mobile phone and accessing it via the headphones.
* When you hear the sound of a short beep, release the button.
Switching a call between the headphones and mobile phone
During the call, you can turn the volume up or down by pressing the Volume button (+/−).
Changing call volume
If telephone function is incorporated in the Bluetooth device, you can make a call using the
headphones.
When the Bluetooth device receives a call, you will hear the
headphones ring.
When you get a call while listening to music, the music will
stop.
When you end the call, the music will resume.
* There are some Bluetooth devices on which audio playback
cannot be restarted.
Multifunction
button
11
Other functions
English
Front Side Back
Press the control
button once.
Playback/pause for
music/movies or
Answering/ending calls
Adjust with the
volume control.
Adjusting volume
* Some smartphones do not support playback and
pause functionality for music/movie files.
* Volume of the connected device itself cannot be
adjusted.
* As the battery power of the playback device
decreases, volume may decrease. Playback will not
be muted, even on the lowest setting.
This product features the play-through function that allows it
to operate like portable headphones and play music from a
portable device even if the headphones are not charged.
Connect the straight plug on the included smartphone cable
to the headphones' headphone jack and connect the L-type
plug to the portable device.
■Using the remote controller with mic for smartphones
The headphones will automatically turn off after 10 minutes of not being connected to a device
with the power turned on.
Auto Power Off function
If this product does not work or other malfunctions occur, press
the reset button using a thin stick.
Once the headphones are reset, they will need to be paired
again with Bluetooth devices.
Reset function
Headphone
jack
Straight plug
Reset button
Control button Volume
control
Microphone
12
Play-through function
Troubleshooting
English
Charge the headphones.
Power is not supplied
Unable to pair
Bring the headphones and the
Bluetooth
device closer together – within the range of 1 meter.
Set proles for the
Bluetooth
device. For procedures on how to set, refer to the operation
manual for the
Bluetooth
device.
Turn on the power of the headphones and the
Bluetooth
device.
No sound comes out / a faint sound
Turn up the volume of the headphones and the
Bluetooth
device.
For the HFP/HSP connection, switch to the A2DP connection.
Switch the output of the
Bluetooth
device to the
Bluetooth
connection.
Pairing is available on version 2.1+EDR or later of the communication system of the Bluetooth
device.
13
Turn down the volume of the headphones and the
Bluetooth
device.
Sound flutters / noise is caused / sound is interrupted
Keep the microwave and other devices such as wireless LAN away from the headphones.
Keep TV, radio and devices with built-in tuners away from the headphones.
Turn off the equalizer settings of the
Bluetooth
device.
Remove obstacles between the headphones and the
Bluetooth
device and bring them closer
together.
Troubleshooting
English
For operation of the Bluetooth device, refer to the device's operation manual.
If the problem still remains, reset the headphones. For the procedure for resetting the device,
refer to "Reset function".
Securely connect the USB charging cable and charge.
The headphones cannot be charged
Turn on the power of the headphones and the
Bluetooth
device.
Turn up the volume of the headphones and the
Bluetooth
device.
For the A2DP connection, switch to the HFP/HSP connection.
Switch the voice output of the
Bluetooth
device to the
Bluetooth
connection.
Cannot hear the person on the other end /
voice of the person on the other end sounds too quiet
14
Loading...