AudioLab 8200AP Schematic
8200AP
VERSION HISTORY
Rev
V01
Date Update Content
July 12, 2012
First Version
8200AP
CONTENT
8200AP
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Introduction
Specification
Assembly Sketch
Schematic Diagram
Wiring Diagram
Silkscreen of Top/Bottom
Maintenance Alignment Procedure
Assembly Parts List
Electronic Parts List
Product Version Deviation
1
2
3-4
5-19
20
21-25
26
27-28
29-34
35-36
INTRODUCTION
No part of this document may be reproduced or transmitted in any form or by any means,electronic or
mechanical, for any purpose, without the express written permission of International Audio Group
Limited (IAG)
This manual is for the exclusive use of IAG, its approved distributors and approved UK service agents.
No part of this manual shall be transferred to any other party without the express written permission of
IAG.
It is the responsibility of the user to ensure that all the information contained in this manual is current.
Notification for new issues of this manual and minor updates will be given via the IAG web-site or on
request.
This manual has been prepared with the greatest care, it is intended for information only and no liability
shall be accepted for errors or changes to specification.
For further service information, parts lists and updates, please contact our web-site at
www.international audio group.com .
C
2012 International Audio Group Limited. All rights reserved.
8200AP
1
8200AP-Speci ficatio n and Featu res-P1/ 1
Digital Inputs
Frequency Response 20Hz–20kHz (±0.2dB), 5Hz–75kHz (±3dB)
THD+N
less than 0.002%
(1)
Signal to Noise > 103dB
Dynamic Range > 103dB
Analogue Inputs (DSP)
Input Sensitivity
0dBu (775mV) , Max 3.5V
(2)
Frequency Response 20Hz–20kHz (±0.2dB), 5Hz–24kHz (±3dB)
THD+N
less than 0.003%
(3)
Signal to Noise
> 98dB
(3)
Dynamic Range
> 100dB
(4)
Analogue Inputs (Direct)
Input Sensitivity
0dBu (775mV) , Max 3.5V
(2)
Frequency Response 20Hz–20kHz (±0.2dB), 5Hz–100kHz (±3dB)
THD+N
less than 0.001%
(3)
Signal to Noise > 110dB
Dynamic Range > 110dB
7.1-channel Bypass Inputs
Input Sensitivity
0dBu (775mV) , Max 3.5V
(2)
Frequency Response 20Hz–20kHz (±0.2dB), 5Hz– 100kHz (±3dB)
THD+N
less than 0.001%
(3)
Signal to Noise > 110dB
Dynamic Range > 110dB
Analogue Outputs
Output Level 0dBu (775mV), Max 3.5V
Volume Control -90dB to +15dB in 1dB steps
Channel Balance Better than ± 0.1dB
Video Outputs
HDMI HDMI 1.4a, Max res. 1080p/60Hz, 36bit Deep Colour, 3D pass through
OSD 1.5Vp-p, 75 ohm, PAL or NTSC
Power Supply
Mains Voltage 230VAC +/- 10%
Power consumption 15W, (< 2W in Standby)
Weight
5.0 Kg (Net)
6.8Kg (Gross)
(note 4) Vin = 2.5V
rms
@ 1KHz, BW = 20Hz - 20KHz
(note) All Voltage levels are in Volts rms. unless otherwise stated.
(note 1) 0dBFS @ 1KHz, 16bit, Fs=44.1KHz, BW = 20Hz - 20KHz
(note 2) Input to Output has a gain of 1 (0dB) when Volume control is set to 0dB
(note 3) Vin = 2V
rms
@ 1KHz, BW = 20Hz - 20KHz
SPECIFICATION
8200AP
2
ASSEMBLY SKETCH
8200AP-Produ ct Explod ed Drawin g-P1/1
11
8
7
5
3
1
8200AP
3
ASSEMBLY SKETCH
8200AP-Packi ng Explod ed Drawin g-P1/1
4
3
5
2
1
8200AP
4
SCHEMATIC DIAGRAM
8200AP-Main Bo ard-P1/ 8
8200AP
5
SCHEMATIC DIAGRAM
8200AP-Main Bo ard-P2/ 8
8200AP
6
SCHEMATIC DIAGRAM
8200AP-Main Bo ard-P3/ 8
8200AP
7
SCHEMATIC DIAGRAM
8200AP-Main Bo ard-P4/ 8
8200AP
8
SCHEMATIC DIAGRAM
8200AP-Main Bo ard-P5/ 8
8200AP
9
Loading...