Page 1
Setup Guide
Audioengine, Ltd.
support@audioengineusa.com
www.audioengineusa.com
© 2010 Audioengine Corp. All Rights Reserved.
Copyright Notice
Audioengine and Audioengine N22 are trademarks of Audioengine Ltd.
Premium Desktop Audio A
Page 2
Contents
Safety Instructions Page 1
Introduction Page 2
Features Page 2
What’s in the Box Page 3
Unpacking Page 3
Setup and Operation Page 4
Cleaning Page 8
Troubleshooting Page 8
Warranty Information Page 10
Contact Us Page 11
audioengine N22 setup guide audioengine N22 setup guide
Page 3
Basic Safety Instructions
Introduction
Read these instructions for all components before using this
•
product.
• Keep these instructions for future reference.
• Heed all warnings on the product and in the owner's guide.
• Follow all instructions.
• Do not use this apparatus near water or moisture. Do not use
this product near a bathtub, washbowl, kitchen sink, laundry
tub, in a wet basement, near a swimming pool, or anywhere
else that water or moisture are present.
• Clean only with a dry cloth and as directed by the
manufacturer. Unplug this product from the wall outlet
before cleaning.
• Do not block any ventilation openings. Install in accordance
with the manufacturer's instructions. To ensure reliable
operation of the product and to protect it from overheating,
put the product in a position and location that will not
interfere with its proper ventilation. For example, do not
place the product on a bed, sofa, or similar surface that may
block the ventilation openings. Do not put it in a built-in
system, such as a bookcase or a cabinet that may keep air
from owing through its ventilation openings.
• Do not install near any heat sources, such as radiators, heat
registers, stoves or other apparatus that produce heat.
• Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding-type plug has two
blades and a third grounding prong. The wider blade or third
prong are provided for your safety. If the provided plug does
not t in your outlet, consult an electrician for replacement of
the obsolete outlet.
• Protect the power cord from being walked on or pinched,
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
• Only use attachments or accessories specied by the
manufacturer.
• Use only with the cart, stand, tripod, bracket or table
specied by the manufacturer or sold with the apparatus.
When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
• Unplug this apparatus during lightning storms or when
unused for long periods of time to prevent damage to this
product.
• Refer all servicing to qualied service personnel.
• Servicing is required when the apparatus has been damaged
in any way such as power supply cord or plug is damaged,
liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
Do not attempt to service this product yourself. Opening or
removing covers may expose you to dangerous voltages or
other hazards. Please contact the manufacturer to be referred
to an authorized service center near you.
• To prevent risk of re or electric shock, avoid over loading
wall outlets, extension cords, or integral convenience
receptacles .
• Do not let objects or liquids enter the product as they may
touch dangerous voltage points or short out parts that could
result in a re or electric shock.
• See product enclosure bottom for safety related markings.
• Use Proper Power Sources. Plug the product into a proper
power source, as described in the operating instructions or as
marked on the product.
• Avoid power lines– Use extreme care when installing an
outside antenna system to keep from touching power lines or
circuits, as contact with them may be fatal. Do not install
external antennas near overhead power lines or other electric
light or power circuits, nor where an antenna can fall into
such circuits or power lines.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: This device
may not cause harmful interference and this device must accept
any interference received, including interference that may cause
undesired operation.
Welcome to the Audioengine family and congratulations on your purchase
of the Audioengine N22 Premium Desktop Audio Amplier! The Audioengine team is dedicated to bringing you the highest quality listening experience possible and the Audioengine N22 amplier was designed with the
same attention to detail and operational simplicity as other Audioengine
products. As with our other past eorts we thank our customers, distributors
and resellers for inspiring us to create another great Audioengine product.
Connect your iPod, computer, and speakers or headphones for a greatsounding personal stereo system with N22. Or plug in an optional Audioengine wireless audio adapter and use N22 to power your home theater rear
speakers.
Features
• Powerful but compact stereo audio amplier
• Cool-running 22 watts RMS per channel
• 2 inputs for iPod, iPhone, computer, TV, etc.
• High-performance headphone amplier
• Variable preamp output
• Gold-plated speaker connectors
Power
Indicator
• High-quality analog volume control
• Detachable power cord
• Power-saving idle mode
Volume/
Power
• Hand-nished MDF wood cabinet
• Integrated vertical stand
CAUTION
RISK OF ELECTRICAL SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK.)
NO USER-SERVICABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED PERSONNEL
1
audioengine N22 setup guide
ATTENTION: POUR RÉDUIRE LE RISQUE DE DÉCHARGE
ÉLECTIQUE, NE RETIREZ PAS LE COUVERCLE (OU
L’ARRIÈRE.) IL NE SE TROUVE ÀL’INTÉRIEURAUCUNE
PIÉCE POUVANT ÊTRE RÉPARÉE PAR L’USAGER.
S’ADRESSER ÀUN REÉPARATEUR COMÉTENT.
AVIS
RISQUE DE CHOC ÉLECTRIQUE
NE PAS OUVRIR
• All cables included!
• Recommended speakers: Audioengine P4
audioengine N22 setup guide
Headphone
2
Page 4
What’s in the Box
• N22 amplier with integrated stand
• N22 power supply
• Detachable AC power cord
• ⁄" audio cable, 2 meters (~6.5 ft)
• RCA audio cable, 1 meters (~3.28 ft)
RCA Input
3.5 mm
Mini-jack Input
Variable
Preamp
Line Out
• Speaker wire (16AWG),
1.75 meters (~5.75 ft)
• Cloth amplier bag
• Cloth power supply bag
USB Power
Speaker
Connectors
• Cloth cable bag
• Setup Guide
Works With
• Audioengine P4 passive speakers
• Audioengine wireless audio adapters
• Desktop computers and laptops (Mac and PC)
• iPods and iPhones
Power
A
B
USB POWER
Made in China
L
LINE OUT
L
OUTPUT
OUTPUT
Setup and Operation
R
INPUTS
Step 1 - Placement
Set the N22 amplier on a solid surface and make sure there is plenty of
ventilation and space around the amplier top and bottom. The integrated
stand is not designed to be removed as the N22 uses a passive convection
R
POWER
system for heat dissipation. Keeping your N22 upright with the stand
attached is important for optimal ventilation and to keep your N22 running
cool.
L
R
CONFORMS TO
UL STD 60065
CERTIFIED TO
CSA STD
C22.2 No. 60065
Intertek
3056826
Step 2 - Connecting the Speaker Wire
The N22 is a stereo power amplier that will power one pair of passive
speakers between 4 and 8 ohms. To connect N22 to your speakers you will
need 2-conductor stranded speaker wire, which is included. The N22 uses
high quality, ve-way gold plated binding posts that will accept heavy
gauge bare wire, banana plugs, spade lugs, or pin terminators. If you use
your own speaker wire we recommend using at least 16 gauge wire and
using the same length of wire from the amplier to each speaker. It's also a
good idea to turn o your amplier before connecting power, audio sources
or speakers.
Preparing the Speaker Wire
• Headphones
• Rear channel surround speakers
• Any products with mini-jack or RCA audio outputs!
Unpacking
Your Audioengine N22 amplier was carefully tested and inspected before
packaging and shipping. After unpacking please check for any damage. It is
rare that any damage occurs during shipping, but if this does happen
contact the shipping company immediately. We recommend that you keep
the original carton and packing material.
3
audioengine N22 setup guide audioengine N22 setup guide
Separate the last 3” of each speaker wire conductor.
Strip ½” of insulation from the end of each wire.
Twist the exposed copper strands with your ngers 3 or 4 times so the
strands stay together.
Note: As you make your connections, be sure to connect the positive (+)
terminals on your amplier to the positive (+) terminals on your speakers.
Even if your wire does not have (+) or (-) markings, most 2-conductor
speaker wire has printing on one side to help you dierentiate between the
wire pairs.
4
Page 5
Using Bare Wire
Use your thumb and nger to unscrew the
binding post connectors on the back of each
speaker.
Insert each speaker wire into the holes on the
side of the binding post connectors, observing
proper polarity.
Retighten the binding posts with your ngers.
The stripped portion of the wire should be
secured rmly in each connector.
Make sure that none of the speaker wire strands
have come in contact with an adjoining terminal.
Repeat steps 1 and 5 to connect speaker wires to
the amplier.
Left SpeakerRight Speaker
L
R
A
INPUTS
B
LINE OUT
L
R
POWER
USB POWER
OUTPUT
L
OUTPUT
R
CONFORMS TO
UL STD 60065
CERTIFIED TO
CSA STD
C22.2 No. 60065
Intertek
3056826
Made in China
Speaker Connections
Step 3 – Connecting the Power Supply
Be sure that the volume/power switch on the front panel is in the OFF
position by rotating it counterclockwise until you hear a click.
Connect the cable with the round end from the power supply to the N22 rear
panel power connector. Note that this connector is “keyed” so line up the
arrow on the cable end with the arrow on the rear panel. Please do not use
excessive force on the connector and use only the power supply provided
with the amplier.
Connect the AC power cable from the power supply to a power outlet and
verify that the indicator light on the power supply is illuminated. We
recommend using a high-quality surge suppressor and/or AC line lter on all
electronics equipment.
Step 4 – Connecting Audio Sources
Using the appropriate audio cable (3.5" mini-jack and/or RCA cable),
connect your audio source (computer, iPod, etc.) to the N22 audio inputs.
One of each cable type is included with your amplier.
Step 5 – Operation
Turn on the N22 volume/power knob and set the volume control to an initial
setting of about 3 o’clock. The front panel power indicator will be
illuminated.
Turn on your audio input source and adjust the volume to your desired
listening level.
Note that both audio inputs on the N22 are active so two audio sources may
be connected to the amplier at the same time without the need for an
input switch. We recommend using the volume control on each audio
source to adjust the overall system volume.
5
audioengine N22 setup guide audioengine N22 setup guide
6
Page 6
Other Features
Headphone Out - For headphone enthusiasts the N22 includes a highperformance, low-noise headphone amplier which works well with all
types of headphones. Even if you don't connect speakers to your N22 the
headphone amplier will make your iPod or computer sound better
through headphones. Keep in mind that permanent hearing loss may
occur if earbuds or headphones are used at high volume so be sure to set
the volume to a safe level.
Cleaning
We don’t recommend using any solvents or cleaners on Audioengine
ampliers, cabinets, or speakers. Just wipe down with a soft, dry cloth.
Troubleshooting
Power supply indicator
is not illuminated
•Check to see that the AC power cord is securely connected to the power supply and to
an AC power outlet.
• Check that the AC power outlet is supplying power.
Line Out - The N22 includes a variable preamp output so you can connect
a subwoofer, external amplier, or Audioengine wireless adapter and
control the volume of the line-out from the front panel.
USB Power - The USB power port allows you to charge and power your
iPod, iPhone, Audioengine wireless adapters or any other USB powered
product through the USB connector on the rear panel. Note that this is for
power only, not USB audio or data transfer.
For a complete list of product features and specications go to:
www.audioengineusa.com
No Sound
Sound through
one speaker only
Lack of bass or
poor imaging
Sound Distorted
•Recheck speaker wire connections from the amplier to each speaker.
• Verify that the amplier and your source components are turned on.
•Check that the AC wall outlet is on and working.
•Check that the cable from the power supply is connected to the N22 and the power
supply indicator is lit.
•Check that the volume/power knob on the front panel is turned on and not set to
minimum volume.
•Check that your audio sources (iPod, computer, etc) are turned on and not set to
minimum volume.
•Check that the cables from your audio sources are working and are properly connected.
• Recheck all speaker wire connections on the speakers and the amplier.
•Check that the cables from your audio sources to the amplier are properly connected.
•If using a computer, verify that the audio output balance setting is centered.
•Check the polarity of the speaker wires on the amplier and both speakers.
•Check the EQ or sound settings on your audio source.
•Decrease the volume of the input audio source and increase the volume of the
amplier.
7
audioengine N22 setup guide audioengine N22 setup guide
8
Page 7
Hum
Adding a new component such as your N22 amplier can bring out hum or
buzz that may not have existed before. Your rst assumption may be that
something is wrong with the component but this is generally caused by a
“ground-loop” in your system. Consider these tips for possible solutions:
• First try moving all components to the same electrical circuit or AC
outlet.
• If the hum or buzz is still present, power o all gear and remove the
mini-jack and/or RCA audio cables to and from the N22 amplier.
• Turn the N22 back on and check for hum. If the noise is still audible try
plugging the N22 power cable into a dierent AC outlet.
• If the hum goes away while the audio cables are still disconnected, the
noise is likely coming from another component in your system. Connect
each component back one at a time and the one that causes the system
to hum is likely the culprit.
• A common ground-loop source is from cable TV or satellite cables. If the
hum or buzz persists after trying the previous tips, disconnect the
coaxial cable from your cable box, TV, or DVR and if the hum goes away
the cable is the cause. In this case you can get a ground-loop isolator
from your local electronics store. These are inexpensive and easy to
connect inline with your video cable.
• Sometimes something as simple as a portable heater or dehumidier
will add noise into your wall wiring that could be picked up by your
audio gear. A dimmer switch on a halogen lamp, a wireless internet
router, or wireless phone near the amplier, for example, could also all
be possible culprits.
The best overall solutions are to use an AC line lter, plug the unit into a
dierent AC circuit, or in the case of noise introduced by a wireless router,
for example, move it further away from your audio gear.
Warranty
Period
All Audioengine products have a 3-year Limited Warranty on parts and labor from date of purchase. Your
warranty is automatic so there is no need to register. This Limited Warranty applies only to Audioengine
products purchased in the Continental United States. For Limited Warranty coverage elsewhere please
contact your Audioengine dealer, reseller, or distributor.
What is covered
All defective parts or faulty workmanship.
What is not covered
The Audioengine Limited Warranty does not cover damage caused by accident, misuse, abuse, neglect,
excessive moisture, lightning, power surges, other acts of nature, unauthorized product modication or
repairs, or failure to follow the instructions outlined in the Setup Guide.
What we will do
We will repair or replace any defective parts, at our option, within a reasonable amount of time and free
of charge any time during the warranty period. After service, we will be responsible for shipping the
product back to you at our expense.
What we ask from you
You will be responsible for shipping or transportation charges directly to Audioengine or to an
authorized dealer. We recommend that you keep the original shipping materials, as it is important that
you package the product so that it will not be damaged during shipping. Audioengine cannot be
responsible for any damages incurred during shipping due to poor packing, so please pack well and
make sure to insure your shipment.
How to obtain Audioengine Warranty service
If you have any questions about your warranty coverage or you think you may need service, email the
Audioengine Authorized Service Center at: support@audioengineusa.com or call toll-free in the United
States at: (877) 853-4447. We will do everything we can to answer your questions and resolve any issues
as quickly as possible.
Exclusive Remedy
This Limited Warranty is fully transferable provided that the current owner furnishes the original proof of
purchase and that the serial number on the product is intact. THE MAXIMUM LIABILITY OF AUDIOENGINE
SHALL NOT EXCEED THE ACTUAL PURCHASE PRICE PAID BY YOU FOR THE PRODUCT. IN NO EVENT SHALL
AUDIOENGINE BE LIABLE FOR SPECIAL, INCIDENTAL, CONSEQUENTIAL OR INDIRECT DAMAGES.
Product Returns and Refunds
Your satisfaction is guaranteed! Should you have a problem or are not satised with any Audioengine
product, send us an email at: support@audioengineusa.com or call toll-free in the United States at:
(877) 853-4447.
9
audioengine N22 setup guide audioengine N22 setup guide
10
Page 8
Contact Us
If you have any questions or feel you may need service contact the reseller
where you purchased your product or feel free to email us directly at:
support@audioengineusa.com or call toll-free in the United States:
(877) 853-4447
About Audioengine
Audioengine designs and builds innovative audio products with all your
music in mind. Great sound, simple but elegant designs, high-quality
materials, and truly useful features are what Audioengine is all about. We
sincerely hope you get as much enjoyment from our products as we've had
creating them! For information about our other products go to:
www.audioengineusa.com
Information for Users on Disposal of Old Equipment
[European Union]
This symbol indicates that the electrical and electronic equipment
should not be disposed as general household waste at its end-of-life.
Instead, the product should be handed over to the applicable collection point for the recycling in accordance with your national legisla-
Attention:
This symbol is
only valid in the
European Union.
inappropriate waste handling of this product. For more information about collection point and recycling of this product, please contact your local municipal oce,
your household waste disposal service or the shop where you purchased the
product. Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.
tion. By disposing of this product correctly, you will help to conserve
natural resources and will help prevent potential negative eects on
the environment and human health that could otherwise be caused by
[Other Countries outside the European Union]
If you wish to dispose of this product, please do so in accordance with applicable
national legislation or other rules in your country for the treatment of old electrical
and electronic equipment.
11
audioengine N22 setup guide audioengine N22 setup guide
Loading...