Audi OBD2 User Manual

Page 1

Audi OBD2 connector pinout

Pin Number Description 1 IGN; Switched to +12V when the ignition is on 2 SAE J1850 Bus + (VPW / PWM) 3 Manufacturer Discretionary 4 Chassis Ground 5 Signal Ground 6 CAN High (ISO 15765-4 and SAE J2284) 7 ISO 9141-2 / ISO 14230-4 K Line 8 Manufacturer Discretionary 9 Manufacturer Discretionary 10 SAE J1850 Bus - (PWM-only) 11 Manufacturer Discretionary 12 Manufacturer Discretionary 13 Manufacturer Discretionary 14 CAN Low (ISO 15765-4 and SAE J2284) 15 ISO 9141-2 / ISO 14230-4 L Line (Optional) 16 Vehicle Battery Power: Type "A" 12V/4A, Type "B" 24V/2A
[ECU PINOUTS ALL BRANDS]
Page 2

Acura OBD2 connector pinout

Pin Number Description 1 Manufacturer Discretionary 2 SAE J1850 Bus + (VPW / PWM) 3 Manufacturer Discretionary 4 Chassis Ground 5 Signal Ground 6 CAN High (ISO 15765-4 and SAE J2284) 7 ISO 9141-2 / ISO 14230-4 K Line 8 Manufacturer Discretionary 9 SCS (Service Check System) - diagnostic codes 10 SAE J1850 Bus - (PWM-only) 11 Manufacturer Discretionary 12 Programming out 13 Input/Output for VTM-4 and immobilizer control 14 CAN Low (ISO 15765-4 and SAE J2284) 15 ISO 9141-2 / ISO 14230-4 L Line (Optional) 16 Vehicle Battery Power: Type "A" 12V/4A, Type "B" 24V/2A
[ECU PINOUTS ALL BRANDS]
Page 3

BMW OBD2 connector pinout

Pin Number
1 Switched +12V Ignition Signal 2 Unused (or unknown) 3 Ethernet RX+ 4 Chassis Ground 5 Signal Ground 6 CAN High (ISO 15765-4 and SAE J2284) (500Kbps) 7 ISO 9141-2 / ISO 14230-4 K Line (10.4Kbps)
8 9 TD (Tachometer Display) Signal / Engine RPM Signal
10 Unused (or unknown) 11 Ethernet RX­12 Ethernet TX+ 13 Ethernet TX­14 CAN Low (ISO 15765-4 and SAE J2284) (500Kbps) 15 ISO 9141-2 / ISO 14230-4 L Line (10.4Kbps) (Optional) 16 Vehicle Battery Power: Type "A" 12V/4A, Type "B" 24V/2A
Description
Secondary K Line for Body/Chassis/Infotainment Modules Ethernet Enable (via 510 Ohm, 0.6 Watt resistor to battery voltage)
[ECU PINOUTS ALL BRANDS]
Page 4

Chrysler OBD2 connector pinout

Pin Number Description 1 Unused (or unknown) 2 SAE J1850 VPW Bus + (10.4Kbps) 3 CCD Bus + 4 Chassis Ground 5 Signal Ground
6
7
8 Unused (or unknown) 9 SCI B Trans (RX) (SAE J2610) (7812.5bps, 62.5Kbps, 125.0Kbps) 10 Unused (or unknown) 11 CCD Bus ­12 SCI B Engine (RX) (SAE J2610) (7812.5bps, 62.5Kbps, 125.0Kbps) 13 Unused (or unknown)
14
• CAN High (ISO 15765-4 and SAE J2284) (500Kbps)
• SCI A Engine (RX) (SAE J2610) (7812.5bps, 62.5Kbps, 125.0Kbps)
• ISO 9141-2 / ISO 14230-4 K Line (10.4Kbps)
• SCI A Engine (TX) (SAE J2610) (7812.5bps, 62.5Kbps, 125.0Kbps)
• SCI A Trans (TX) (SAE J2610) (7812.5bps, 62.5Kbps, 125.0Kbps)
• SCI B Engine (TX) (SAE J2610) (7812.5bps, 62.5Kbps, 125.0Kbps)
• CAN Low (ISO 15765-4 and SAE J2284) (500Kbps)
• SCI A Trans (RX) (SAE J2610) (7812.5bps, 62.5Kbps, 125.0Kbps)
[ECU PINOUTS ALL BRANDS]
Page 5
15 16 Vehicle Battery Power: Type "A" 12V/4A, Type "B" 24V/2A
• ISO 9141-2 / ISO 14230-4 L Line (10.4Kbps) (Optional)
• SCI B Trans (TX) (SAE J2610) (7812.5bps, 62.5Kbps, 125.0Kbps)

Ford OBD2 connector pinout

Pin Number
1
2 SAE J1850 PWM (Ford SCP) Bus + (41.6Kbps)
3
4 Chassis Ground 5 Signal Ground 6 CAN High (ISO 15765-4 and SAE J2284) (500Kbps) 7 ISO 9141-2 / ISO 14230-4 K Line (10.4Kbps)
8
9 Battery Power (Switched) (vehicle battery power available via the ignition
Description
• Infotainment CAN High
• Ignition Control (activates low current switching device to power ignition current)
• DCL +
• Medium-Speed CAN High (125Kbps, 250Kbps)
• UBP Network #1 (9600bps)
• Infotainment CAN Low
• Trigger Signal (multiple module trigger input controlled through the communication link to initiate / terminate an event)
[ECU PINOUTS ALL BRANDS]
Page 6
switch or ignition control [Pin 1])
10 SAE J1850 PWM (Ford SCP) Bus - (41.6Kbps)
• DCL -
11
12 Flash EEPROM 13 14 CAN Low (ISO 15765-4 and SAE J2284) (500Kbps)
15 Unused by Ford 16 Vehicle Battery Power: Type "A" 12V/4A, Type "B" 24V/2A
• Medium-Speed CAN Low (125Kbps, 250Kbps)
• UBP Network #2 (9600bps)
• FEPS — ECU Programming Voltage
• Flash EEPROM

GM OBD2 connector pinout

Pin Number Description 1 2 SAE J1850 VPW Bus + (10.4Kbps)
3 Object Detection CAN Bus + 4 Chassis Ground 5 Signal Ground 6 CAN High (ISO 15765-4 and SAE J2284) (500Kbps) 7 ISO 9141-2 / ISO 14230-4 K Line (10.4Kbps)
• Single-Wire CAN (SAE J2411 / GMW3089) (33.3Kbps)
• GM UART / ALDL (SAE J2740) (8192 bit/s)
[ECU PINOUTS ALL BRANDS]
Page 7
8 Manufacturer Discretionary 9 GM UART / ALDL (SAE J2740) (8192 bit/s) 10 Unused (or unknown) 11 Object Detection CAN Bus ­12 Chassis High-Speed CAN Bus + (500Kbps) 13 Chassis High-Speed CAN Bus - (500Kbps) 14 CAN Low (ISO 15765-4 and SAE J2284) (500Kbps) 15 ISO 9141-2 / ISO 14230-4 L Line (10.4Kbps) (Optional) 16 Vehicle Battery Power: Type "A" 12V/4A, Type "B" 24V/2A

Honda OBD2 connector pinout

Pin Number Description 1 Manufacturer Discretionary 2 SAE J1850 Bus + (VPW / PWM) 3 Manufacturer Discretionary 4 Chassis Ground 5 Signal Ground 6 CAN High (ISO 15765-4 and SAE J2284) 7 ISO 9141-2 / ISO 14230-4 K Line 8 Manufacturer Discretionary 9 SCS (Service Check System) - diagnostic codes
[ECU PINOUTS ALL BRANDS]
Page 8
10 SAE J1850 Bus - (PWM-only) 11 Manufacturer Discretionary 12 Programming out 13 Input/Output for VTM-4 and immobilizer control 14 CAN Low (ISO 15765-4 and SAE J2284) 15 ISO 9141-2 / ISO 14230-4 L Line (Optional) 16 Vehicle Battery Power: Type "A" 12V/4A, Type "B" 24V/2A

Hyundai OBD2 connector pinout

Pin Number Description 1 Gearbox diagnostic 2 ABS diagnostic, BUS+ Line 3 Manufacturer Discretionary 4 Chassis Ground 5 Signal Ground 6 CAN High (ISO 15765-4 and SAE J2284), ABS/ASR diagnostic 7 Engine and gearbox diagnostic ISO 9141-2 / ISO 14230-4 K Line 8 ABS diagnostic 9 Cruise-control diagnostic 10 SAE J1850 Bus - (PWM-only) 11 Manufacturer Discretionary
[ECU PINOUTS ALL BRANDS]
Page 9
12 Airbag diagnostic 13 Manufacturer Discretionary 14 CAN Low (ISO 15765-4 and SAE J2284) VSS (vehicle speed) 15 ISO 9141-2 / ISO 14230-4 L Line (Optional) 16 Vehicle Battery Power: Type "A" 12V/4A, Type "B" 24V/2A

Infinity OBD2 connector pinout

Pin Number Description 1 CHECK 2 SAE J1850 Bus + (VPW / PWM) 3 Manufacturer Discretionary 4 Chassis Ground 5 Signal Ground 6 CAN High (ISO 15765-4 and SAE J2284) 7 ISO 9141-2 / ISO 14230-4 K Line 8 Ignition ON 9 ABS 10 SAE J1850 Bus - (PWM-only) 11 Adjust Switch 12 SCI TX 13 SCI RX
[ECU PINOUTS ALL BRANDS]
Page 10
14 CAN Low (ISO 15765-4 and SAE J2284) 15 ISO 9141-2 / ISO 14230-4 L Line (Optional) 16 Vehicle Battery Power: Type "A" 12V/4A, Type "B" 24V/2A

KIA OBD2 connector pinout

Pin Number Description 1 Gearbox diagnostic 2 ABS diagnostic, BUS+ Line 3 Manufacturer Discretionary 4 Chassis Ground 5 Signal Ground 6 CAN High (ISO 15765-4 and SAE J2284), ABS/ASR diagnostic 7 Engine and gearbox diagnostic ISO 9141-2 / ISO 14230-4 K Line 8 ABS diagnostic 9 Cruise-control diagnostic 10 SAE J1850 Bus - (PWM-only) 11 Manufacturer Discretionary 12 Airbag diagnostic 13 Manufacturer Discretionary 14 CAN Low (ISO 15765-4 and SAE J2284) VSS (vehicle speed) 15 ISO 9141-2 / ISO 14230-4 L Line (Optional)
[ECU PINOUTS ALL BRANDS]
Page 11
16 Vehicle Battery Power: Type "A" 12V/4A, Type "B" 24V/2A

Lexus OBD2 connector pinout

Pin Number Description 1 Manufacturer Discretionary 2 SAE J1850 Bus + (VPW / PWM) 3 Manufacturer Discretionary 4 Chassis Ground 5 Signal Ground 6 CAN High (ISO 15765-4 and SAE J2284) 7 ISO 9141-2 / ISO 14230-4 K Line 8 Manufacturer Discretionary 9 Tachometer ECM 10 SAE J1850 Bus - (PWM-only) 11 Manufacturer Discretionary 12 Brake Actuator Assembly
13 14 CAN Low (ISO 15765-4 and SAE J2284)
15 ISO 9141-2 / ISO 14230-4 L Line (Optional) 16 Vehicle Battery Power: Type "A" 12V/4A, Type "B" 24V/2A
Timing check - ignition advance angle adjustment or ABS slow codes out
[ECU PINOUTS ALL BRANDS]
Page 12

Mazda OBD2 connector pinout

Pin Number
1 Manufacturer Discretionary 2 SAE J1850 Bus + (VPW / PWM)
3 4 Chassis Ground
5 Signal Ground 6 CAN High (ISO 15765-4 and SAE J2284) 7 ISO 9141-2 / ISO 14230-4 K Line 8 Manufacturer Discretionary 9 Manufacturer Discretionary 10 SAE J1850 Bus - (PWM-only)
11 12 Manufacturer Discretionary
13 Manufacturer Discretionary 14 CAN Low (ISO 15765-4 and SAE J2284) 15 ISO 9141-2 / ISO 14230-4 L Line (Optional)
Description
Low speed (125Kb) CAN bus. This bus is used for some IC, RFA and other units.
Low speed (125Kb) CAN bus. This bus is used for some IC, RFA and other units.
[ECU PINOUTS ALL BRANDS]
Page 13
16 Vehicle Battery Power: Type "A" 12V/4A, Type "B" 24V/2A

Mercedes Benz OBD2 connector pinout

Pin Number
1 2 SAE J1850 Bus + (VPW / PWM)
3 TD engine rotation speed 4 Chassis Ground 5 Signal Ground 6 CAN High (ISO 15765-4 and SAE J2284)
7 8 Manufacturer Discretionary
9 ABS, ASR, ESP, ETS, BAS diagnostic 10 SAE J1850 Bus - (PWM-only) 11 Gearbox and other transmission components (EGS, ETC, FTC) 12 All activity modules (AAM), Radio (RD), ICS… 13 AB diagnostic - safety systems 14 CAN Low (ISO 15765-4 and SAE J2284)
Description Ignition control (EZS), air-conditioner (KLA), PTS, safety systems
(Airbag, SRS, AB) and some other
ISO 9141-2 / ISO 14230-4 K Line Engine control diagnostic (ME/MSM/CDI)
[ECU PINOUTS ALL BRANDS]
Page 14
15 16 Vehicle Battery Power: Type "A" 12V/4A, Type "B" 24V/2A
ISO 9141-2 / ISO 14230-4 L Line (Optional) IC, KI, TAU, LWR diagnostic

Mitsubishi OBD2 connector pinout

Pin Number
1 Diagnostic control 2 SAE J1850 Bus + (VPW / PWM) 3 SWS communication line 4 Chassis Ground 5 Signal Ground 6 CAN High (ISO 15765-4 and SAE J2284)
7 8 Manufacturer Discretionary
9 ETACS 10 SAE J1850 Bus - (PWM-only) 11 ECU optimisation control 12 Manufacturer Discretionary 13 Manufacturer Discretionary
Description
ISO 9141-2 / ISO 14230-4 K Line MPI, CVT, SRS airbags and immobilizer
[ECU PINOUTS ALL BRANDS]
Page 15
14 CAN Low (ISO 15765-4 and SAE J2284) 15 ISO 9141-2 / ISO 14230-4 L Line (Optional) 16 Vehicle Battery Power: Type "A" 12V/4A, Type "B" 24V/2A

Nissan OBD2 connector pinout

Pin Number Description 1 CHECK 2 SAE J1850 Bus + (VPW / PWM) 3 Manufacturer Discretionary 4 Chassis Ground 5 Signal Ground 6 CAN High (ISO 15765-4 and SAE J2284) 7 ISO 9141-2 / ISO 14230-4 K Line 8 Ignition ON 9 ABS 10 SAE J1850 Bus - (PWM-only) 11 Adjust Switch 12 SCI TX 13 SCI RX 14 CAN Low (ISO 15765-4 and SAE J2284) 15 ISO 9141-2 / ISO 14230-4 L Line (Optional)
[ECU PINOUTS ALL BRANDS]
Page 16
16 Vehicle Battery Power: Type "A" 12V/4A, Type "B" 24V/2A

Renault OBD2 connector pinout

Pin Number
1 Manufacturer Discretionary 2 SAE J1850 Bus + (VPW / PWM) 3 Manufacturer Discretionary 4 Chassis Ground 5 Signal Ground 6 CAN High (ISO 15765-4 and SAE J2284) 7 ISO 9141-2 / ISO 14230-4 K Line 8 Manufacturer Discretionary 9 Manufacturer Discretionary 10 SAE J1850 Bus - (PWM-only) 11 Manufacturer Discretionary
12
13 14 CAN Low (ISO 15765-4 and SAE J2284)
Description
LS CAN Bus used for low speed CAN bus, also called as multimedia CAN bus LS CAN Bus used for low speed CAN bus, also called as multimedia CAN bus
[ECU PINOUTS ALL BRANDS]
Page 17
15 ISO 9141-2 / ISO 14230-4 L Line (Optional) 16 Vehicle Battery Power: Type "A" 12V/4A, Type "B" 24V/2A

Subaru OBD2 connector pinout

Pin Number Description 1 Ground 2 SAE J1850 Bus + (VPW / PWM) 3 Manufacturer Discretionary 4 Chassis Ground 5 Signal Ground 6 CAN High (ISO 15765-4 and SAE J2284) 7 ISO 9141-2 / ISO 14230-4 K Line 8 Manufacturer Discretionary 9 SSM (Subaru Select Monitor) timing pulse 10 SAE J1850 Bus - (PWM-only) 11 SSM (Subaru Select Monitor) timing pulse 12 SSM to ECM signal 13 ECM to SSM signal 14 CAN Low (ISO 15765-4 and SAE J2284) 15 ISO 9141-2 / ISO 14230-4 L Line (Optional) 16 Vehicle Battery Power: Type "A" 12V/4A, Type "B" 24V/2A
[ECU PINOUTS ALL BRANDS]
Page 18

Toyota OBD2 connector pinout

Pin Number Description 1 Manufacturer Discretionary 2 SAE J1850 Bus + (VPW / PWM) 3 Manufacturer Discretionary 4 Chassis Ground 5 Signal Ground 6 CAN High (ISO 15765-4 and SAE J2284) 7 ISO 9141-2 / ISO 14230-4 K Line 8 Manufacturer Discretionary 9 Tachometer ECM 10 SAE J1850 Bus - (PWM-only) 11 Manufacturer Discretionary 12 Brake Actuator Assembly
13 14 CAN Low (ISO 15765-4 and SAE J2284)
15 ISO 9141-2 / ISO 14230-4 L Line (Optional) 16 Vehicle Battery Power: Type "A" 12V/4A, Type "B" 24V/2A
Timing check - ignition advance angle adjustment or ABS slow codes out
[ECU PINOUTS ALL BRANDS]
Page 19

Volkswagen OBD2 connector pinout

Pin Number Description 1 IGN; Switched to +12V when the ignition is on 2 SAE J1850 Bus + (VPW / PWM) 3 Manufacturer Discretionary 4 Chassis Ground 5 Signal Ground 6 CAN High (ISO 15765-4 and SAE J2284) 7 ISO 9141-2 / ISO 14230-4 K Line 8 Manufacturer Discretionary 9 Manufacturer Discretionary 10 SAE J1850 Bus - (PWM-only) 11 Manufacturer Discretionary 12 Manufacturer Discretionary 13 Manufacturer Discretionary 14 CAN Low (ISO 15765-4 and SAE J2284) 15 ISO 9141-2 / ISO 14230-4 L Line (Optional) 16 Vehicle Battery Power: Type "A" 12V/4A, Type "B" 24V/2A
[ECU PINOUTS ALL BRANDS]
Page 20

Volvo OBD2 connector pinout

Pin Number Description 1 Manufacturer Discretionary 2 SAE J1850 Bus + (VPW / PWM) 3 Low speed CAN - high 4 Chassis Ground 5 Signal Ground 6 CAN High (ISO 15765-4 and SAE J2284) High speed CAN 7 ISO 9141-2 / ISO 14230-4 K Line ABS, DSA, TCU AW, IMMOB, ECC 8 Manufacturer Discretionary 9 Manufacturer Discretionary 10 SAE J1850 Bus - (PWM-only) 11 ECU, Fenix 5.1 (Volvo S40 and some others), Low speed CAN - low 12 Manufacturer Discretionary 13 Cruise-control 14 CAN Low (ISO 15765-4 and SAE J2284) 15 ISO 9141-2 / ISO 14230-4 L Line Motor 16 Vehicle Battery Power: Type "A" 12V/4A, Type "B" 24V/2A
[ECU PINOUTS ALL BRANDS]
Loading...