AU Infobar C01 Basic Manual

Preface

Thank you for purchasing the INFOBAR C01.
Before using your INFOBAR C01, be sure to read the Basic Manual
(this PDF manual) to ensure correct usage.
After you have finished reading this manual, store this PDF manual
and the printed manuals (Accessories) in safe places so you can
retrieve them whenever you need them. If the printed manuals
(Accessories) are lost, please contact an au shop or Customer
Service Center.

■ Downloading Manuals

You can download the Basic Manual (this manual) and the Instruction
Manual (Accessory) (Japanese) or full Instruction Manual (Japanese)
in PDF format from the au homepage.

http://www.au.kddi.com/torisetsu/index.html

• To display the Basic Manual (this manual), the Instruction Manual
(Accessory) (Japanese) or full Instruction Manual (Japanese) in PDF
format on the INFOBAR C01, purchase the full version of Documents
To Go or install an application which allows you to display PDF files.

For Learning Operations of the INFOBAR C01

■ Instruction Manual (Accessory)

This manual describes basic operations of major functions of the
INFOBAR C01.
For detailed descriptions on various functions, refer to the Instruction
Manual application (Japanese) available on the INFOBAR C01 or full
Instruction Manual (Japanese) available on the au homepage.

■ Instruction Manual Application

You can use the Instruction Manual application (Japanese)
pre-installed in the INFOBAR C01 with which you can check detailed
operation methods on this au phone terminal.
Also, you can activate intended functions from an explanation screen
depending on the functions.
On the iida Home, tap Instruction Manual

• To use the application for the first time, you need to download and
install it by following on-screen instructions.

ii

Safety Precautions

Be sure to read the Safety Precautions “安全上のご注意” in the
Instruction Manual (Japanese) to ensure proper usage of the
INFOBAR C01.
For troubleshooting, check the symptom of your INFOBAR C01 in
auお客さまサポート(au Customer Support) on the au homepage.

http://www.kddi.com/customer/service/au/trouble/kosho/
index.html

Before Using an au Phone

• You cannot receive or make calls in a location where the signal

cannot be received, even within the service area. Calling may not be
available in a location where the signal is weak. If you move to a
location where the signal is weak during a call, the call may be
interrupted.

• The au phone is a digital cell phone and can maintain a high call

quality until the signal weakness reaches its limit. Therefore, once
the limit has been reached, the call may be disconnected suddenly.

• Note that the au phone uses signals which may be intercepted by a

third party. (However, the CDMA/GSM system enables highly
confidential call communications.)

• The au phone is a wireless station which is compliant with the Radio

Act, and may be subject to inspections regulated by the Radio Act.

• When you insert the au IC-Card, the product number information of

your au phone is sent to KDDI CORPORATION for the security and
operation status notification of the au phone.

• Always be considerate of others around you when using your au

phone in public places.

• For a child’s use, read the Basic Manual and give your child

instructions on proper use.

• The INFOBAR C01 is a cell phone compatible with the international

roaming service. Each network service which is described in the
Basic Manual varies depending on the area or service. For details,
refer to Global Passport Owner’s Guide (Japanese).

1

Cell Phone Etiquette Accessories

Warranty

(Japanese)

INFOBAR C01

microSD memory card

(2 GB) (Sample)

• This is inserted in the

INFOBAR C01 at the time of
purchase.

Cell phones always emit weak radio waves when power is on. Use cell

Introduction

phones in an enjoyable and safe manner without forgetting to be
considerate of others around you.

■ Use of cell phones is not allowed in some places.

• Using a cell phone while driving a car/motorcycle is dangerous and
is prohibited by law. Also, using a cell phone while riding a bicycle
may be punished by law.

• Using a cell phone in an aircraft is prohibited.

■ Be considerate of where you use the cell phone and

how loudly you talk.

Do not make calls in theaters, museums, libraries, and other similar
places. Turn power off or turn on Manner mode so as not to disturb
others around you by ring tones.

• Do not use the cell phone on a street where you might interrupt the
flow of pedestrians.

• Move to areas where you will not inconvenience others on trains or in
hotel lobbies.

• Refrain from talking in a loud voice.

• Obtain the permission of other people before you take their photos

with the cell phone’s camera.

■ Be considerate of people around you.

• Some people close to you in crowded places such as packed trains
may be using a cardiac pacemaker. Turn the cell phone off in such
places.

• Abide by the rules of hospitals and other medical institutions where
it is forbidden to use or carry cell phones.

2

Check whether all the contents are included.

Battery pack
(SHX12UAA)

SHARP microUSB-3.5φ

conversion cable 01

(SHX11QVA)

● Instruction Manual (Japanese)

● Safety Precautions (Japanese)

● Notice Sheet (Japanese)

● Setting Guide (Japanese)

● JIBUN BANK・au Insurance Service Guide (Japanese)

● Global Passport Owner’s Guide (Japanese)

The following items are not included.

• AC adapter

• Earphone

• microUSB cable

• Purchase a specified charger (sold separately).

• The illustrations in this manual may look different from the actual

product.

Illustrations and Descriptions in This Manual

■ Note on Key Illustrations

In this manual, the key illustrations are simplified as shown below.

■ Description of Operations for Selecting Item/Icon/

Key etc.

In this manual, operation steps are described as below.

Description Explanation

On the character entry
screen, [Change
input mode.
f while sleep mode is
set.

• Explanations of this manual are based on the case when the color of the

INFOBAR C01 is “NISHIKIGOI” as an example.

• Explanations of this manual are based on the case when the INFOBAR C01

is held vertically. If you hold it horizontally, menu items/icons/on-screen keys
etc. may be different.

• Explanations of this manual ar e based on touch panel operations when you

can operate with either touch panel or keys.

• Menu items, layers and icons described in this manual may be different

according to functions being used and conditions.

• In this manual, entering Lock No. is mentioned as one of the unlock

methods.

• “microSD™ memory card” and “microSDHC™ memory card” are

abbreviated as “microSD memory card” or “microSD”.

• “SHARP microUSB-3.5φ conversion cable 01” is abbreviated as
“microUSB-3.5φ conversion cable”.

Tap on the character entry
screen. Then tap Change input mode.

Press f while sleep mode is set.

Introduction

3

■ Note on Screenshots

The screenshots in this manual are simplified and may look different
from the actual screens. Also, part of the screen may be abbreviated.

Introduction

In this manual,
part of the screen
such as icons are
abbreviated.

4

Actual screen

In this manual

Security Code and PIN Code

Security Code and Passwords

You have to use each security code for using the INFOBAR C01.
You can use a security code and other passwords described below.
Take care not to forget your security code and passwords because
they are required for performing various operations and using
subscription services.

● Security Code

Usage

A Using the Answering Service (Voice Mail) and Call Transfer

Example

Initial

Setting

remotely from a fixed-line phone

B Making inquiries, applications, and changes while using

Customer Service Center voice guidance, and au homepage

The four-digit number you wrote on your subscription form

● Lock No.

Usage

Setting/Canceling Screen lock, Restrict address book, etc.

Example

Initial

1234

Setting

● PIN Code

Usage

Preventing unauthorized use of the au IC-Card by a third party

Example

Initial

1234

Setting

PIN Code

If the PIN code is incorrectly entered three times consecutively, the
PIN code will be locked. Use the PUK code to unlock the PIN code.

■ PIN Code

You can set the INFOBAR C01 to require PIN code entry every time
the power is turned on, to prevent unauthorized use of the au IC-Card
by a third party.

• At the time of purchase, the PIN code is not to be required to use

phone. On the iida Home, tap Settings [Location & security [Set up
UIM card lock [Mark Lock UIM card to set the PIN code to be
required.
The PIN code is also required when setting Lock UIM card.

• The initial setting of the PIN code is “1234”. On the iida Home, tap

Settings [Location & security [Set up UIM card lock [Change UIM
PIN to change the PIN code to a four- to eight- digit number.

■ PUK Code

Enter the PUK code when the PIN code is locked.

• PUK code is an eight-digit number given at the time of purchase,
and is printed on the back side of the plastic card where your au
IC-Card is attached.

• When you enter the PUK code, on the iida Home, tap Settings
[Location & security [Set up UIM card lock [Change UIM PIN to
set the new PIN code.

• If the PUK code is incorrectly entered ten times consecutively,
contact an au shop, PiPit or the Customer Service Center.

• When the PIN code is locked, the INFOBAR C01 may be restarted for the

security reasons.

• PIN code cannot be reset even if you carry out the operation (on the iida

Home, tap Settings [Privacy [Reset all).

<Back up notes on the memory contents of the INFOBAR C01>

● Please back up* notes on the important information whose contents are

saved on the INFOBAR C01 by yourself or are received/downloaded to the
INFOBAR C01 from external devices.
The memory contents of the INFOBAR C01 may be deleted or changed
because of unexpected elements such as static electricity and malfunction
or modifications, improper operations, etc.

* Methods for the b ackup

It is recommended that text information such as t he address book or downloaded
dictionaries be backed up in the microSD memory card . You can forward each data to
a PC by attaching one on mails.
However, some data such as data protected by copyright canno t be backed up even
with the above mentioned methods.

Introduction

5

Contents

Preface............................................................ ii

Contents

For Learning Operations of the

INFOBAR C01 ................................................ ii

Safety Precautions.......................................... ii

Before Using an au Phone.............................. 1

Introduction

Cell Phone Etiquette ...............................................2

Accessories.............................................................2

Illustrations and Descriptions in This Manual.......... 3

Security Code and PIN Code..................................4

Security Code and Passwords................................4

PIN Code.................................................................4

Getting Ready

Names and Functions of Parts................................8

Removing/Attaching the Battery Pack...................11

Removing the Battery Pack...................................11

Attaching the Battery Pack ...................................11

Using a Hand Strap...............................................12

Attaching a Hand Strap ........................................12

Removing a Hand Strap........................................13

Using au IC-Card ..................................................14

au IC-Card ............................................................14

Removing au IC-Card ...........................................15

Inserting au IC-Card .............................................15

Using microSD Memory Card ...............................16

microSD Memory Card .........................................16

Removing microSD Memory Card ........................17

Inserting microSD Memory Card ..........................17

Charging the Battery Pack ....................................18

Turning the Power On/Off .....................................20

Turning the Power On ...........................................20

6

Turning the Power Off........................................... 20

Restarting the INFOBAR C01 ............................... 20

Sleep Mode...........................................................20

Switching the Display Language to English.......... 21

Initial Setup ...........................................................21

Setting Up a Google Account ............................... 21

Setting au one-ID.................................................. 21

Learning the Basics

Operating the Touch Panel................................... 22

iida Home and widget Home.................................23

Using the iida Home ............................................. 24

Viewing the iida Home.......................................... 24

Using the Menu of the iida Home......................... 24

Adding/Editing Panels .......................................... 25

Moving Panels ......................................................25

Viewing the iida Home Editing Screen ................. 25

Using the widget Home.........................................26

Using the Menu of the widget Home.................... 26

Moving/Removing Widgets................................... 26

Application List......................................................27

Using the Status Bar............................................. 30

Indicators.............................................................. 30

Using Notification/Status Panel ............................32

Switching Orientation............................................ 33

Displaying Available Menu....................................33

Character Input (Hardware Keyboard).................. 34

Viewing the Character Entry Screen..................... 34

Switching Character Entry Modes ........................ 35

Entering Emoji/Symbol/Facemark......................... 35

Character Input (Software Keyboard)................... 36

Switching Software Keyboards............................. 36

Viewing the Character Entry Screen..................... 37

Switching Character Entry Modes ........................ 39

Entering Emoji/Symbol/Facemark......................... 39

Switching Input Software ...................................... 40

Phone

Making a Call ........................................................41

Making an International Call (au International Call

Service) .................................................................42

Answering a Call ...................................................43

Answering an Incoming Call .................................43

Putting the Call on Hold ........................................43

Answering with the Message of Answering Memo

..............................................................................43

Returning a Call (Outgoing History/Incoming

History) ..................................................................43

Turning On Manner Mode .....................................44

Turning On the Answering Memo..........................44

Playing a Message in Answering Memo................45

Address Book

Adding an Address Book Entry .............................46

Using an Address Book.........................................47

Viewing the Address Book Details Screen............47

Using Phone Number............................................48

Using Mail Address...............................................48

Mail

Using E-mail ..........................................................49

Sending E-mail Messages.....................................49

Receiving E-mail Messages ..................................50

Receiving Mail Message by Inquiring....................51

Reading Received E-mail Messages.....................51

Setting Mail Filters.................................................55

Using SMS (C-mail)...............................................57

Sending SMS (C-mail) Messages .........................57

Receiving SMS (C-mail) Messages.......................58

Reading Received SMS (C-mail) Messages .........59

Rejecting Spam SMS (C-mail) Messages .............61

Setting Account for PC-mail ..................................61

Sending PC-mail Messages ..................................63

Receiving PC-mail Messages................................63

Using Gmail...........................................................63

Sending Gmail.......................................................64

Receiving Gmail ....................................................64

Internet

Viewing Sites with Browser...................................65

Using Bookmarks/History ..................................... 65

Displaying a Site from Bookmarks/History ........... 65

Bookmarking a Web Page.................................... 66

Multimedia

Using the Camera................................................. 67

Cautions for Using the Camera ............................ 67

Taking Photos....................................................... 69

Recording Movies .................................................70

Using Photo ..........................................................71

Using Contents Manager......................................72

Displaying/Playing Data .......................................72

Using Menu in the Contents Screen..................... 73

1Seg

Cautions for Using 1Seg....................................... 74

TV antenna ...........................................................74

Initial Setup of 1Seg..............................................75

Watching 1Seg ..................................................... 75

Applications

Using au Disaster Countermeasure Application... 77

Using Android Market ...........................................79

Using au one Market.............................................79

Using GREE Market ............................................. 79

Using au Customer Support ................................. 79

au Customer Support ...........................................79

Using Anshin Security Pack .................................80

Using 3LM Security .............................................. 81

Using Remote Support ......................................... 81

Using VirusBuster Mobile for au........................... 81

Managing Applications..........................................82

Settings of INFOBAR C01

Checking Your Profile............................................83

Changing the Incoming Ring Tone........................83

Changing the Wallpaper........................................83

Initializing microSD Memory Card .........................84

Global Function

Using Global Passport CDMA/GSM......................85

GLOBAL PASSPORT.............................................85

For Overseas Use without Anxiety ........................86

Configuring the Overseas Settings .......................86

Making a Call at Your Travel Destination ..............87

Receiving a Call at Your Travel Destination..........88

Appendix/Index

Troubleshooting.....................................................89

Index......................................................................91

Contents

7

Names and Functions of Parts

■ Front

Getting Ready

A Earpiece (Receiver)

Emits voice of other party during a call, messages in Answering
memo, etc.

B Display
C e Menu key

Displays the option menu.

8

D # Home key

Use it to display the iida Home etc.

E Number key

Use it to enter characters, make a call, etc. You can activate an
application by holding down a number key if you use Quick Launch.
For details on Quick Launch, refer to “Using the Menu of the iida
Home”.

5: Disables sleep mode during sleep mode.
0 to 9: Switches the character each time you press the key,

and enter the character.

.: You can switch the entered character to the uppercase/

lowercase one, or for entering Hiragana/Katakana, add
dakuten/handakuten to the character. You can return the
determined characters to the undetermined state.

/: Displays the characters assigned to the same key in the

reverse rotation for entering characters. Inserts a line feed at
the cursor position before entering characters/after
determining characters.

F Proximity sensor/Light sensor

Proximity sensor prevents operating the touch panel incorrectly
during a call. Light sensor detects the ambient brightness and
adjusts the brightness of the display.

G Charging/Incoming indicator

Illuminates in red while charging.
Flashes according to the settings when receiving a call or mail
message.

H ^ Return key

Returns to the previous page.

I Mouthpiece (Microphone)

Transmits your voice to the other party during a call. It is also used
for recording sounds. Take care not to cover the microphone with
your fingers etc.

■ Left Side

J f Power key

Turns on/off the power, and sets/disables sleep mode.

K ud Volume up/down key

Adjusts the volume.
Hold d down on the iida Home/widget Home/unlock screen
to enable/disable Manner mode.

■ Bottom

L External connection jack cover
M External connection jack

Use it to connect the INFOBAR C01 to the microUSB-3.5φ
conversion cable, the common AC adapter 03 (sold separately),
the microUSB cable 01 (sold separately), SHARP microUSB-18-pin
(charger) conversion cable 01 (sold separately), the microUSB
stereo earphone conversion adapter 01 (sold separately), etc.

Getting Ready

9

■ Back

Getting Ready

N Internal antennas area

Do not cover the internal antennas area with your hand when you
call, use the Internet, Wi-Fi
information (only the upper part on the back of the cell phone is
responsible for Wi-Fi
paste stickers etc. around the internal antennas area. Otherwise,
the quality of calls/communications will deteriorate.

O Camera lens
P Infrared port

Sends and receives data via infrared communication.

10

®

or Bluetooth® function or retrieve GPS

®

, Bluetooth® and GPS functions). Also, do not

Q Speaker

Emits ring tones, alarm tones, etc.

R Battery pack cover
S FeliCa mark

Hold it over a reader/writer when using Osaifu-Keitai
Sends and receives data via IC communication.

T Strap eyelet

String the hole with the cord of a hand strap.

U Mobile light

Flashes in red while activating Camera.

■ Back (Inside the Battery Pack Cover)

®

.

V microSD memory card slot
W Battery pack
X Strap hook

Attach a hand strap. For details, refer to “Using a Hand Strap”.

Y Tray

Use it when inserting an au IC-card.

Removing/Attaching the Battery Pack

Removing the Battery Pack

When removing the battery pack, turn off the INFOBAR C01.

A Remove the battery pack cover on the back of the

INFOBAR C01.

Hook a fingertip (nail) on the concave portion of the external
connection jack cover with the center of the battery pack cover
pressed (A), and then remove the battery pack cover by pulling up in
the direction of the arrow (B).

Concave portion

B Remove the battery pack.

Remove the battery pack by pulling up the protruding edge in the
direction of the arrow.

Protruding edge

Battery pack

• When removing the battery pack cover, do not warp it too much.

• When removing the battery pack, always pull up the protruding edge of the

battery pack. Doing otherwise may result in damage to the INFOBAR C01 or
the battery contacts.

Attaching the Battery Pack

Use the specified battery pack for the INFOBAR C01 and attach it
properly.

A Align the contacts on the battery pack with those of

the INFOBAR C01 and then insert the battery pack

securely with the protruding edge facing up on the

battery pack.

Contacts on
INFOBAR C01

Getting Ready

11

B After attaching the battery pack cover, press the

periphery of the battery pack cover securely from

above, and make sure that it is closed properly.

Getting Ready

A Put the string of the hand strap through the strap

eyelet of the battery pack cover.

Hand strap

Battery pack cover

• Before attaching the battery pack, make sure that the au IC-Card is inserted

properly.

• Failure to follow the correct procedure when attaching the battery pack may

result in damage to the battery pack or the battery pack cover.

Using a Hand Strap

Attaching a Hand Strap

You can put a commercially available hand strap on the INFOBAR
C01.
Depending on how you put the hand strap, the battery pack cover
may come off, and that causes the strap to come off.
Put the hand strap on the INFOBAR C01 after removing the battery
pack cover.

12

Strap eyelet

B Put the string of the hand strap on the strap hook of

the INFOBAR C01 and pull the string lightly in the

direction of the arrow to secure it.

When you put the string, make sure that it is not twisted.

Strap hook

String of hand strap

Examples of wrong attachment

C Make sure that the hand strap does not come off and

attach the battery pack cover while pulling the hand

strap lightly.

Make sure that there is no space between the battery pack cover and
the INFOBAR C01.

Removing a Hand Strap

Remove the hand strap after removing the battery pack cover.

A Loosen the string of the hand strap as shown.

Getting Ready

• Do not put multiple hand straps on the strap ho ok.

• When you attach the battery pack cover, make sure that the hand strap

does not come off.

• The hand strap may come off when attachin g the battery pack cover with

the string not secured properly on step B. Also, be sure that there is no
space between the battery pack cover and the INFOBAR C01 when
attaching the battery pack cover.

• Do not swing the INFOBAR C01 with the hand strap. It may result in an

accident, such as injury, or malfunctio n or damage to the INFOBAR C01.
Also, do not use a damaged hand strap, such as when its string is
damaged.

Strap hook

String of hand
strap

B Push the string of the hand strap out in the direction

of the arrow with one side of the string held with a

finger.

Push the string of the hand strap out as the string passes through the
gap.

13

C Remove the hand strap by pulling it in the direction of

au IC-Card

IC (metal
surface) part

the arrow.

Getting Ready

• If you have trouble removing the hand strap, do not pull it forcefully. Remove

it using pointed objects.

Using au IC-Card

au IC-Card

An au IC-Card records your personal information
such as phone numbers.

• Confirm the correct direction when you insert the au IC-Card.

• Note that inserting or removing the au IC-Card forcibly may result in

malfunction or damage.

• Make sure to unplug microUSB plugs such as AC adapter 03 (sold

separately) from the INFOBAR C01 when inserting or removing the au
IC-Card.

■ When an au IC-Card is not inserted or an au IC-Card

other than yours is inserted

You cannot use the INFOBAR C01 with a card other than an au
IC-Card inserted.
If an au IC-Card is not inserted or an au IC-Card other than yours is
inserted and the INFOBAR C01 is turned on, the following operations
are unavailable. Also, / is not displayed.

*

• Making

/Receiving a call

• Sending/Receiving mail messages

• Checking Own phone number/Own mail address

• Setting up UIM card lock

* Making an e mergency call to 110 (Police), 119 (Fire and Ambulanc e) and 118 (Regional Coast

Guard) and making a call to 157 (Customer Service Center) are also unavailable.

■ Restriction Settings with PIN Code

You can set the INFOBAR C01 to restrict the use of the phone by
others through changing the PIN code or locking the UIM card in
order to protect your important private information while you are using
your au IC-Card. For details, refer to “PIN Code”.

14

Removing au IC-Card

Turn off the power and remove the battery pack before removing the
au IC-Card.

A Pull the tab of the tray in the direction of the arrow

and remove the au IC-Card.

Tab

B Attach the battery pack and battery pack cover.

Inserting au IC-Card

Turn off the power and remove the battery pack before inserting the
au IC-Card.

A Pull the tab of the tray in the direction of the arrow.

B Place the au IC-Card on the tray with the IC (metal

surface) side down and insert it securely.

Insert the au IC-Card according to the orientation of its cutout.

Cutout

C Attach the battery pack and battery pack cover.

• Inserting the tray not deeply enough may prevent the INFOBAR C01 from

functioning properly.

• When the tray comes off, insert the tray straightly.

Getting Ready

15

Using microSD Memory Card

microSD Memory Card

You can set microSD memory card (including microSDHC memory
card) to the INFOBAR C01, and save data. And also you can save
address book, mail messages, bookmarks, etc. in microSD memory
card.

Getting Ready

• The maximum file size available on a microSD memory card is 2 GB per file

when saving data to microSD memory card.

• A microSD memory card initialized on other devices may not be used on the

INFOBAR C01 properly. On the iida Home, tap Settings [microSD & phone

storage [Unmount microSD [OK [Erase microSD [Erase microSD
[Enter Lock No. [OK [Erase everything to initialize the microSD

memory card.

• For operations to play/display data in the microSD memory card, on the iida

Home, tap Contents Manager to use Contents Manager.

• Some files such as copyright protected data may not be played on the

INFOBAR C01 even if they are moved/copied from the PC etc. to a microSD
memory card successfully.

■ Handling Precautions

• Do not remove the battery pack and do not turn off the INFOBAR
C01 and other equipment while reading, writing, playing, saving or
moving/copying data. It may result in damage to data in the
INFOBAR C01 or microSD memory card or data loss.

• Do not drop or subject the INFOBAR C01 to vibration or impact with
a microSD memory card inserted. It may result in damage to
recorded data or data loss.

• Do not insert objects other than microSD memory card such as
liquid, metals or flammable items into the microSD memory card
slot. It may result in a fire, electric shock or malfunction.

• The following microSD memory cards have been confirmed for
operation based on the criteria by au. For operation confirmation
results of other microSD memory cards, contact each microSD
memory card manufacturer.

<microSD/microSDHCMemoryCard>

Manufacturer 2 GB 4 GB 8 GB 16 GB 32 GB
Toshiba
Panasonic
SanDisk
ADTEC
Buffalo
Sony

○ ○ ○ ○ ○
○ ○ ○ ○ ○
○ ○ ○ ○ ○
○ ○ ○ ○ −
○ ○ ○ ○ ○
○ ○ ○ ○ −

○: Confirmed operation

−: Unconfirmed operation or not for sale

As of November 2011

* 4 GB or more are for microSDHC memory card.
* Operation is co nfirmed for microSD memory cards that are sold as of Nove mber 2011. For

the latest information on operation confirmation, v isit the au homepage or contact the
Customer Service Center.

16

Removing microSD Memory Card

Turn off the power and remove the battery pack before removing the
microSD memory card.

A Remove slowly the microSD memory card in the

direction of the arrow.

Pull slowly the microSD memory card straight out.

Inserting microSD Memory Card

Turn off the power and remove the battery pack before inserting the
microSD memory card.

A Confirm the direction of the microSD memory card

and insert it slowly in the direction of the arrow.

microSD memory
card slot

Insert this card
with the
microSD logo
side up

Getting Ready

B Attach the battery pack and the battery pack cover.

• Do not touch the terminal part of microSD memory card.

• Do not remove the microSD memory card forcefully. It may result in damage

to the microSD memory card or the INFOBAR C01 or data loss.

• Application installed to microSD memory card cannot be used once you

removed microSD memory card.

• The microSD memory card may be warm after a long time use. It is normal.

B Attach the battery pack and the battery pack cover.

• Insert a microSD memory card with the right side up in the appropriate

direction.
Inserting a microSD memory card forcefully into the slot could result in
failure to remove the microSD memory card or damage to the microSD
memory card or the INFOBAR C01.

17

Charging the Battery Pack

The battery pack is not fully charged at the time of purchase. Charge
the battery pack when you use the INFOBAR C01 for the first time or
the battery level becomes low. Charging is finished when the red
charging/incoming indicator goes out.
The usage times are as follows.

Getting Ready

Continuous stand-by
time

Continuous talk time Approx. 370 min

* These times are b ased on the case when the INFOBAR C01 is used in Japan.

• The INFOBAR C01 and battery pack may become warm during charging

but this is not a malfunction.

• Charging the INFOBAR C01 while using the camera function etc. may

lengthen the charging time.

• If you perform various operations with a specified charger (sold separately)

connected to the INFOBAR C01, charging/battery level consumptions may
take place in a short time. Frequently charging the battery pack shortens its
service life.

• If the charging/incoming indicator of the INFOBAR C01 flashes in red,

check whether the battery pack is properly attached, an external device is
properly connected to the cell phone, etc. If the cell phone flashes even
after you have checked that, stop recharging the cell phone and please
contact an au shop or Customer Service Center.

• Properly close the external connection jack cover. Also, do not pull it

forcibly or twist it.

Approx. 350 hours (while Wi-Fi® and
Pedometer are not used)
Approx. 340 hours (while Wi-Fi
used and Pedometer is used)
Approx. 170 hours (while Wi-Fi
and Pedometer is not used)
Approx. 160 hours (while Wi-Fi
Pedometer are used)

®

is not

®

is used

®

and

• Each of the continuous talk time and continuous stand-by time is an

average usage time combining the time during which a cell phone is carried
around by a user and properly receives radio waves plus the time during
which a cell phone is stationary and properly receives radio waves.
According to usage conditions such as battery level status and
temperature, the signal strength in a place where the cell phone is used,
settings of functions, etc., the usage times may be reduced to less than half
under the following cases.

• A cell phone is frequently used in a place where (out of service area
indicator) appears on it.

• The Wi-Fi® function, Bluetooth® function, mail function, camera function,
1Seg function, location information, etc. is used.

• A cell phone is set not to enable the sleep mode because of an
application etc.

• Applications which remain activated in the background are used.

• If you stop charging while the charging/incoming indicator still illumi nates

during charging, the cell phone may be left not fully charged even if
appears on it. In such case, the average usage times shorten.

■ Charging the Battery Pack with the Specified AC

Adapter (sold separately)/DC Adapter (sold
separately)

The followings are the explanation of how to connect the common AC
adapter 03 (sold separately)/the common DC adapter 03 (sold
separately) to charge.
Charging time is as shown below.

Specified AC adapter
(sold separately)

Specified DC adapter
(sold separately)

Approx. 150 min

Approx. 200 min

18

A Open the external connection jack cover of the

INFOBAR C01.

External
connection jack

C Plug the common AC adapter 03 (sold separately)

power plug into a 100 V AC power outlet/Plug the

common DC adapter 03 (sold separately) plug into a

cigarette lighter socket.

Getting Ready

Check the
orientation

Common AC adapter 03 (sold separately)/
Common DC adapter 03 (sold separately)

B Insert the microUSB plug of the common AC adapter

03 (sold separately)/the common DC adapter 03 (sold

separately) to the external connection jack of the

INFOBAR C01.

Common AC
adapter 03
(sold separately)

Charging/Incoming indicator illuminates in red, and the battery icon
appears with superimposed. When charging is finished, the
charging/incoming indicator goes out.

Common DC
adapter 03
(sold separately)

D When charging is finished, pull the microUSB plug of

the common AC adapter 03 (sold separately)/common

DC adapter 03 (sold separately) straight out from the

external connection jack of the INFOBAR C01.

E Close the external connection jack cover of the

INFOBAR C01.

F Unplug the common AC adapter 03 (sold separately)

power plug from the power outlet/Unplug the

common DC adapter 03 (sold separately) plug from

the cigarette lighter socket.

• Although you can charge the INFOBAR C01 while the power is turned on,
charging time lengthens.

19

• If you charge the INFOBAR C01 when the battery has run out, the charging/

incoming indicator may not illuminate soon. However, charging is in
progress.

■ Charging with a PC

When you connect the INFOBAR C01 to a USB port of a PC through
which the INFOBAR C01 can be charged, the charging/incoming
indicator illuminates in red and charging starts. When charging is

Getting Ready

finished, the charging/incoming indicator goes out.

• If you use the microUSB cable to charge the INFOBAR C01, it may take the

INFOBAR C01 longer to be fully charged than if you use the specified AC
adapter (sold separately).

Turning the Power On/Off

Turning the Power On

A Hold down f for at least two seconds.

《Unlock screen》

Slide to to unlock.

20

Slide to the shortcut to start it.
If the incoming history/e-mail/SMS (C-mail) is registered as a shortcut,
the shortcut illuminates in red when a call is missed or a new e-mail/
SMS (C-mail) is received.

• The initial setting of the touch panel is executed while the logo is displayed

after the power is turned on. Do not touch the screen, otherwise touch panel
operations may not be performed properly.

Turning the Power Off

A Hold down f for at least two seconds.
B Power off [OK.

Restarting the INFOBAR C01

Turn off the INFOBAR C01 once and restart.

A Hold down f for at least two seconds.

B Reboot [OK.

Sleep Mode

If you press f or no operation is made for a while, the screen is
turned off temporarily, and then sleep mode is set.

■ Disabling Sleep Mode

A f/5 while sleep mode is set.

• In some applications in use, the screen which was displayed before sleep

mode is set may be displayed when sleep mode is disabled.

• Do not touch the screen when you disable sleep mode. Otherwise touch

panel operations may not be performed properly.

Switching the Display Language to English

言語とキーボード

auone-ID とは？

You can switch the display language for function names and other
items to English.

A On the iida Home, (Settings).

B (Language & keyboard).
C (Select language).

言語（Language）を選択

D English.

Initial Setup

After you purchase the INFOBAR C01, the initial setup screen is
displayed automatically when turning on the power or inserting
another’s au IC-Card.
For detailed operations on the initial setup, refer to the Setting Guide
(Japanese).

A Set Date & time [Next.
B Set Location [Next.

C Set Vivid display mode [Next.
D Set Other.

Set Wi-Fi settings, au one-ID setting, Lost device protection Settings, Google
account, Text font or Profile settings.

E Done.

F Yes/No.

If you tap No, the initial setup screen will not be displayed from the next
startup.

設定

• Alternatively, on the iida Home, tap Settings [Default settings to set up.

Setting Up a Google Account

If you set up a Google account, you can use online services provided
by Google.
When you activate an application which requires a Google account
before setting one up, the Google account adding screen is
displayed.

A On the Google account adding screen, Next.
B Create/Sign in.

If you have already had a Google account, tap Sign in, enter the user
name and password and tap Sign in.
If you have not had a Google account, tap Create and follow the
on-screen instructions to register one.

Setting au one-ID

A On the iida Home, au one-ID setting.

Alternatively, on the iida Home, tap Settings [au one-ID setting.

B OK.

The authentication starts.

C (Set/Save au one-ID).

auone-IDの設定・保存

Tap (What is au one-ID?) to activate the browser
and display the explanation of au one-ID.

D Follow the instructions of the screen and set an au

one-ID.

If you have already acquired an au one-ID, set the au one-ID you have.
If you have not acquired an au one-ID, register a new ID.

Getting Ready

21

Operating the Touch Panel

The display of the INFOBAR C01 is a touch panel. You can operate
the INFOBAR C01 by directly touching the screen.

■ Tap/Double-Tap

Tap: Gently touch a screen and then immediately release your finger.
Double-tap: Tap quickly twice on the same position.

• Select an item or icon displayed on the screen. Double-tap to
enlarge/reduce the screen.

Learning the Basics

■ Long-Touch

Keep touching an item, key, etc.

• Display context menu etc.

■ Slide

Gently touch a screen and then trace it to the desired direction.

• Scroll screen or switch pages. In addition, operate gauge and bar
when adjusting volume and brightness.

■ Flick

Touch a screen and then quickly flick your finger up, down, left or
right.

• Switch pages, enter characters by flick input, etc.

22

■ Pinch

Touch a screen with two of your fingers and then move them apart or
closer together.

• Enlarge/Reduce the screen.

iida Home and widget Home

Home consists of two screens which are the iida Home and widget
Home. You can paste applications, shortcuts, etc. on the iida Home
and you can paste widgets on the widget Home.
Flick the screen to the left/right to switch the iida Home and widget
Home.

Widget

Learning the Basics

■ Drag

Gently touch a screen and then trace it to the desired position.

• Move an icon on the screen to the desired position.

Flick to the left

Flick to the right

《widget Home》《iida Home》

23

Using the iida Home

Viewing the iida Home

Applications, shortcuts, etc. are displayed as panels section by
section. Select a panel to activate the application.

Learning the Basics

《iida Home》

A Status bar
B Application/Shortcut panel
C Section bar

Long-touch a section bar to display the section bar list. Drag it to
any section bar and release your finger to scroll the iida Home to
the selected section bar position.

D Bottom key

Operate with the same method as section bars.

E Quick search box
F Opening/Closing section key

Using the Menu of the iida Home

A On the iida Home, e.
B

Add/Edit Panel Refer to “Adding/Editing Panels”.
Theme Sets the theme of the iida Home.
Quick Launch Assigns applications to each number key.
Quick Search
Box
Scroll
Absorption
System Settings Performs the various settings for the

Quick Launch

• Hold down the number key on the iida Home/widget Home to quickly

activate the assigned application.

• Long-touch an assigned application [OK to disable the setting for Quick

Launch.

• 0, . and / are not available for Quick Launch. In advance, the

following functions are assigned to the keys.

0: Displays the quick search box.
.: You can use Call/Ans Memo.
/: The mobile light illuminates.

* The mobile l ight goes out when you hold down / on the iida Home/widget Home or

approximately 30 seconds have passed while the light illuminates.

Sets whether to display/hide the quick
search box.
Sets whether to adjust the stop position when
scrolling the iida Home.

INFOBAR C01.

24

Adding/Editing Panels

A On the iida Home, e [Add/Edit Panel.
B

Applications Displays the application list.

Alarm You can use Alarm.
Memo You can use Memo.
Photo You can use Photo.
World Clock You can use World Clock.
Bookmark Adds a shortcut to the bookmark.
Call/Ans Memo Adds a shortcut to Call/Ans Memo.
Contact Adds a shortcut to the selected contact that

Direct Dial Adds a shortcut that enables you to call to

Direct Message Adds a shortcut that enables you to create a

Directions &
Navigation

Energy save Adds a shortcut to Energy save.
Music playlist Adds a shortcut to the music play list.
One Seg Adds a shortcut to each menu of One Seg.
Settings Adds a shortcut to the various settings.

• If you change the size of a displayed panel, the displayed contents are

changed.

• Panels are added at the bottom of the iida Home.

• You can paste up to 240 panels on the iida Home.

• Tap Edit to set to display/hide panels.

• Select the application on which is

displayed to set the displayed size etc.

enables you to call, create a mail, etc. from
the iida Home.

the selected contact.

mail by using a selected contact as the
destination.

Adds a shortcut of the Google navigation to
the destination.

• When the number of installed applications exceeds the maximum number of

panels that can be pasted, the panels of the installed applications are
automatically set to be hidden.

Moving Panels

A

On the iida Home, long-touch a panel.

B Drag it to the position to move to and release your

finger.

Drag it to a section bar to display the section bar list. And then drag it
to any section bar and release your finger to move the panel to the
bottom of the selected section.

Viewing the iida Home Editing Screen

A Long-touch the iida Home.

The iida Home editing screen is displayed and you can set the
sections and panels.

《iida Home editing screen》

Learning the Basics

25

A Setting key

Tap it to display the setting items. You can hide panels or change
the size of the displayed panels.

B Section bar adding key

Drag it to the right edge of the screen and release your finger to
add a section bar.

C Section bar deleting key

Drag it to the left edge of the screen and release your finger to
delete a section bar.

Learning the Basics

D Add panel

Adds a panel.

• For details, refer to “Adding/Editing Panels”.

E Auto align

Panels are aligned automatically to fill the space of the iida Home.

• If you change the size of a displayed panel, the displayed contents are

changed.

• Tap the panel whose size can be changed to switch the size of the

displayed panel.

• Tap a section bar to edit the section title.

Using the widget Home

Using the Menu of the widget Home

A On the iida Home, flick the screen to the right [e.
B

Add Widgets

Manage apps Use “Manage applications”.
Wallpaper Sets by selecting a wallpaper from the data

Search Use the quick search box.
Notifications Displays the notification/status panel.
System Settings Performs the various settings for the

Wallpaper

• While a live wallpaper is set, the battery level is reduced faster than usual.

Adds a widget.

Wallpapers

Sets by selecting a wallpaper from the data
in the microSD memory card or the images
registered in advance.

in the microSD memory card or the images
registered in advance.

INFOBAR C01.

Moving/Removing Widgets

On the iida Home, flick the screen to the right

A

[long-touch a widget to move/remove.

■ When moving the widget

B Drag it to the position to move to and release your

finger.

26

■ When removing the widget

B Drag it to at the left edge of the screen and release

your finger.

• You can switch pages by dragging an icon to the top or bottom edge of the

screen.

Application List

Icon Name of icon Description

*

Edy｜au Pay monthly charge of Edy and au

*

Facebook Check This is an application in which you

*

GREE This is an official application from

*

LISMO Book Store Enjoy many e-books such as

*

LISMO WAVE Enjoy FM radio all over Japan,

*

Photo Air This app will backup your photos

*

picplz Pictures taken by a smartphone

at the same time.

© bitWallet,Inc.

can check the number of updated
items on the iida Home. The
functions that you can check are
information, message and friend.

au one GREE, a free social mobile
gaming network with more than 25
million users (※As of November,

2011).

comics, novels and photo albums.

music clips, and live channel etc.

that have taken with your
smartphone to your computer
automatically.

© KDDI / Powered by Eye-Fi

can easily be modified showing
taste like miniature or toy camera.

Icon Name of icon Description

*

Polaroid PoGo App You can take a picture with

Polaroid vintage color and variety
of frames.
It’s available with PoGo printer and
“Photo Air”.

*

Snapeee Edit images shot with a

Summit Global Japan K.K.

Smartphone using stamps and
frames and share them with other

*

Task Cleaner This is an application for saving

people.

battery consumption. You can cut
back on wasteful consumption of
electricity by using this. Also, you
can check each of the currently
running applications as a list and
freely terminate them or change

*

unlimited Use monthly paid music service

their operation conditions.

that enables you to listen to a

*

UNO FREE Play UNO and challenge yourself

lineup of over 1 million music.

with increasingly difficult games in
Tournament Mode, or compete
against friends online through Wi-Fi

*

じぶん銀行 (JIBUN
BANK)

connection.
You can check the statement of
your account balance, search for

nearest available ATMs, and so on
through the screen optimized for

*

スマホカバー
(Smartphone cover)

Smartphones.
Allows you to buy smartphone
covers originally designed by

popular fashion brands.

Learning the Basics

27

Icon Name of icon Description

*

ナビウォーク (Navi
Walk)

This is an application for
navigating you to the best suited
routes both for on foot and by

*

ファッション通販
(Internet Shopping
Site)

vehicle.
You can get the latest items of

famous fashion brands, jackets of
the IS series collaborated with the
brands, and many kind of items on

Learning the Basics

3LM Delete data in the INFOBAR C01

the internet shopping site.

and microSD memory card or lock
its operations in case of loss of
your INFOBAR C01.

Address Book Manage phone numbers or mail

addresses.

au one Market Allows you to install Android

applications recommended by au.

au one-ID Setting Set up an au one-ID.
au Wi-Fi接続ツール
(au Wi-Fi

Use Wi-Fi® easily in the spot where
au Wi-Fi SPOT is available.

connection tool)
auお客さまサポー
ト (au Customer

Support)

You can check the subscription
contents or monthly usage of your
au phones etc. with this
application. You can change your
rate plan, apply for optional
services and so on at au Customer
Support website.

au災害対策 (au
Disaster
Countermeasure)

This is an application in which you
can use Disaster Message Board
and Early warning mail
(earthquake early warnings and
disaster/evacuation information).

Browser Browse web sites on the Internet.

28

Icon Name of icon Description

Calculator Use calculator.
Calendar Save and manage schedules.
Camera Take photos (still images).
Camera Reader Switch Barcode reader, Business

card reader, Kanji/English
grabber, Text reader, Information
reader to use.

Clock Use World Clock, Alarm, Timer and

Stopwatch.

Compass Displays the compass and your

current location on the Google
Maps.

Contents Manager Displays and manage data on a

microSD memory card.

Dictionary Search for information in the

built-in dictionary of the INFOBAR
C01 or dictionaries on the Internet.

Documents To Go Displays Microsoft Office

documents.

Download Displays the list of data

downloaded from the browser and

manage them.
E-mail Use e-mail.
Energy save Save the battery by switching

modes.
Facebook Use Facebook.
Flash Player
Settings

Set the usage of the data storage

area and the network bandwidth

on devices.
Font Manager Change the fonts displayed on the

screen.

Icon Name of icon Description

Friends Note “au one Friends Note” can manage

Native Address Book of your
phone and multiple social
networking services in just one

application.
GLOBAL
PASSPORT PLUS

Check whether the connected

carrier applies to Overseas

Double-Teigaku or confirm the

method of making international

calls and the call fees.
Gmail Use Gmail.
Google Search Search for information in the

INFOBAR C01 or on web sites.
GREE_MARKET

(GREE Market)

This application allows you to

browse games and other content

provided by au one GREE.

You do not need a GREE account

*

Instruction Manual Check the contents written in the

in order to use this application.

full Instruction Manual (Japanese).

You can search explanations of a

function that you want to use by

using the table of contents, index

and search engine.
Latitude Google Maps to check the location

of your friends.
LISMO Player Plays music or checks information

about the playing music.
maker appli Use various services such as

downloading and viewing

applications.
Maps Use Google Maps.
Market Use Android Market.
Memo Register and check memos.

Icon Name of icon Description

Movie Edit Clip movies recorded with

INFOBAR C01 in the specified
range and save.

Navigation Search for routes to the destination

on Google Maps.
News & Weather Displays news and weather.
Notepad Create memos.
One Seg Watch 1Seg.
Osaifu-Keitai Use Osaifu-Keitai®.
PC-mail Use PC-mail.
Pedometer Use pedometer.
Phone Make a call and use outgoing

history/incoming history.
Photo Display images in the microSD

card as a list and edit them.
Picture Sort images and movies by

people, event and location and use

them.
Places Search for facilities around your

current location and display them

on the Google Maps.
RSS Check updated information on the

registered RSS.
Send and Receive
by Infrared

Send and receive data via infrared

communication.
Settings Check settings or information.
Skype Makes a call or exchanges instant

messages (chat).
Smart Familink Play data released by DLNA

compatible devices on the

INFOBAR C01 using Wi-Fi
SMS(C-mail) Use SMS(C-mail).
Talk Use Google Talk.

Learning the Basics

®

.

29

Icon Name of icon Description

TwiCheck Use Twitter.
Twitter Use Twitter.
VideoCamera Record movies.
Voice Recorder Record a voice.
Voice Search Enter a keyword for Google search

with your voice.
Weather Displays weather.
YouTube Use YouTube.

Learning the Basics

ウイルスバスター

(VirusBuster)

Blocks improper applications and

sites in order to protect young

people.
テレビ．Gガイド
(TV. G-Guide)

View TV program table or search

programs. Functions using 1Seg or

remote timer recording can be

*

ニュースEX (News
EX)
リモートサポート
(Remote Support)

used.

Check latest news, weather,

fortune-telling, etc.

Call for technical supports on the

phone operations by sharing the

screen that you are watching with

au operators.
安心アプリ制限

(Restrict
Applications)

* Requires download and installation to use.

• When you use functions of applications, call fees may apply depending on

the function.
If you have not subscribed to IS NET, au.NET charges (525 yen including
tax for the used month) and communication charges apply.

• Icon designs may be changed without prior notice.

Restrict inappropriate applications,

®

Wi-Fi

communication, etc. for

children.

Using the Status Bar

Indicators

The notification indicators to notify you of a missed call, a new mail
message or a running operation are displayed on the left side of the
status bar, while the status indicators to show the status of the
INFOBAR C01 are on the right side.

■ Examples of notification indicator

Indicator Description

Missed call
E-mail information

: New mail message

: E-mail message failed to be sent
New mail message (SMS (C-mail))
New mail message (PC-mail)
New mail message (Gmail)
Alarm terminated

• Appears when the alarm is terminated without the

operation for terminating the alarm.
Schedule notification of the calendar
1Seg information

: Watching information, Recording reservation

information : Recording information
Playing music
USB debug connecting
Dialing, Calling, During an incoming call
Putting a call on hold

30

Indicator Description

Answering memo
Skype™｜au status

: Signed in : New event
Space available less than approx. 10 %
Bluetooth® file receiving request
USB connecting

: Card reader mode : Fast transfer mode

: USB connecting (in Card reader mode

connecting)

Data upload, File sending

: Uploading data, Sending file, Finished sending

file, Failed to send file : Finished uploading data

: Waiting to upload data

• The Uploading data indicator and Sending file

indicator are displayed as animations.
Downloading, Finished downloading, Installing data or
application, Receiving, Finished receiving file, Failed to
receive file

• The Downloading indicator and Receiving file indicator

are displayed as animations.
Finished installing
Connected, Unconnected to VPN
Update available
Major Update (OS Update) available
Indicators collected
Energy saving setting

: Waza-ari mode : Emergency mode

• When multiple notifications of the same type exist, the number of them is

displayed on the lower right of some indicators.

■ Examples of status indicator

Indicator Description

Time
Alarm set

~ Battery level

~ : Battery level display : No battery
: Battery level unknown

• While charging, the battery icon appears with
superimposed. The charge indicator other than is
displayed as an animation.

Offline mode set
Signal strength (Receiving electric field)

: Level 4 : Level 3 : Level 2
: Level 1 : Level 0 : Out of service area

3G data communication status

: Waiting : Receiving : Sending
: Sending and Receiving

CDMA 1X data communication status

: Waiting : Receiving : Sending
: Sending and Receiving

GSM data communication status

: Waiting : Receiving : Sending

: Sending and Receiving
In roaming (CDMA)
Signal strength in roaming (GSM)

: Level 4 : Level 3 : Level 2 : Level 1

: Level 0
Character type

: Kanji : Half-width alphabet

: Half-width numeric : Half-width Katakana

: Full-width alphabet : Full-width numeric

: Full-width Katakana : Character code
Manner mode status

: Standard manner mode : Drive manner mode

: Silent manner mode

Learning the Basics

*

*

*

*

*

31

Indicator Description

During a call using hands-free
Microphone set to “mute” during a call
Home Network status

: Suspending (Yellow): Preparing
(Blue): Running

Wi-Fi® signal strength

*

: Level 4 : Level 3 : Level 2
: Level 1 : Level 0

Learning the Basics

Bluetooth® in use

: Waiting : Connecting

GPS in use

• The GPS information positioning indicator is displayed
as an animation.

Data synchronizing
Answering memo set

: No Answering memo
: Answering memo (one to nine entries)
: Answering memo (ten entries)

Osaifu-Keitai® function locked

* Displayed i n green when you login using your Google account.

Using Notification/Status Panel

In the notification/status panel, you can check the details on
notification indicators and status indicators or activate an application
corresponding to the indicator.
You can also set Manner mode, VeilView, etc.

32

A Tap the status bar.

《Notification/Status panel》

A Power control

You can set Wi-Fi
brightness of screen.
You can save power by switching the settings frequently when
you do not use functions.

B Notification area

You can check the status of the INFOBAR C01 and contents of
notifications. You can tap to activate a corresponding
application depending on the information.

C VeilView

You can set VeilView.

D Auto-rotate

You can set the automatic rotation of the display.

E Time

Displays the current time. You can tap to set the alarm.

F Clear

You can clear all the notifications by tapping the key.

®

, Bluetooth®, GPS, auto-sync, and

G Manner mode

You can set Manner mode.

H Running Apps

Displays the running applications list screen.

I microSD Settings

You can set the microSD memory card and phone space.

J Close bar

You can hide the notification/status panel by tapping the tab.

Displaying Available Menu

■ Option Menu

The option menu is displayed by tapping e on the screen where the
menu is available.

Example: In the inbox screen

Switching Orientation

Portrait and landscape display are switched according to the
orientation of the INFOBAR C01.

Example: When rotating the INFOBAR C01 from Portrait (Landscape)

display to the left (right).

《Landscape display》《Portrait display》

• Operate the INFOBAR C01 in the upright position. The screen display may

not be changed if the INFOBAR C01 is laid in parallel to the ground.

• On the iida Home, tap Settings [Display settings [Auto-rotate screen to set

whether to switch portrait display and landscape display.

• In some applications such as Video Camera, the screen display may not be

switched regardless of the orientation or setting of the INFOBAR C01.

Option menu

More

• When the number of available o ption menus exceeds the number that can

be displayed on the screen as icon, More is displayed. Option menus that
cannot be displayed as icon are collected into More, and tap More to
display them.

• Even on the same screen, the number of items collected into More differs

depending on the setting and condition since the number of option menus
displayed differs depending on the setting and condition.

• In this manual, operation to tap More is not described for tables listing

option menu.

Learning the Basics

33

■ Context Menu

The context menu is displayed by long-touching an item or a display
where the menu is available.

Example: In the character entry screen (Notepad)

Learning the Basics

Character Input (Hardware Keyboard)

Viewing the Character Entry Screen

Context menu

A Character entry area
B Prediction candidates list/Relational prediction candidates list/

Normal conversion candidates list

If the word prediction function is enabled, the prediction
candidates list is displayed when characters are entered. If the
relational prediction function is enabled, the relational prediction
candidates list is displayed when an entry is selected from the
prediction candidates list.
Enter characters and tap to display the normal conversion
candidates list.

• You can enlarge the candidates list area by tapping . Tap
to return it to the original display.

34

《Character entry screen》

C Cursor key/Phrase reduction key/Phrase extension key

/ : Moves the cursor to the left and right. Change the

range of the characters for character input and
conversion.

/ : Sets how many characters put together are

recognized as a phrase.

D Emoji, Symbol and Facemark key/Symbol and Facemark key/

Normal conversion key/Prediction key/Half-width space key

: Displays the emoji/symbol/facemark list.
: Displays the symbol/facemark list.
: Displays the normal conversion candidates list.
: Displays the prediction candidates list.
: Enters a half-width space.

E OK key/Complete key

: Determines the entering characters.
: Completes the character entry and close the character

entry screen.

F Kana, Alphanumeric key/Character entry mode key

: Displays katakana, alphabet, number and predicted date

and time assigned to the entered key as conversion
candidates.

When you switch the character types, the display changes as follows.

: Kanji
: Half-width alphabet
: Half-width numeric
: Half-width Katakana
: Full-width alphabet
: Full-width numeric
: Full-width Katakana
: Character code

G Delete key

Deletes the selected character or the character on the left of the
cursor. When the cursor is at the beginning, the character on the
right of the cursor is deleted.

• While the prediction candidates list/relational prediction candidates list/

normal conversion candidates list is not displayed, tap ^ to hide the
keyboard.

Switching Character Entry Modes

A On the character entry screen, long-touch the

character entry mode key [Change input mode.

B Select the character type.

• The character type is switched in order of “Half-width alphabet”

[“Half-width numeric” [“Kanji” each time you tap the character entry
mode key.

• Some character modes cannot be used depending on the screen or the

application.

Entering Emoji/Symbol/Facemark

A On the character entry screen, / .

《Emoji/Symbol/Facemark list screen》

Learning the Basics

35

A Character switch tab

Switches the emoji/symbol/facemark.

B Emoji/Symbol/Facemark list

Displays the emoji/symbol/facemark list screen for each
category.

• Long-touch a facemark to edit it. However, facemarks in
History cannot be edited.

C Close key

Learning the Basics

Returns to the character entry screen.

D Delete key

Deletes the selected character or the character on the left of
the cursor. When the cursor is at the beginning, the character
on the right of the cursor is deleted.

E Character entry mode switch key/Edit key

: Displays emojis converted automatically when sent to

a cell phone of other carrier.
: Displays normal emojis.
: Displays full-width symbols.
: Displays half-width symbols.

B Select an emoji/a symbol/facemark.

Press .// to display the previous/next category or page.

• There are some lists that cannot be displayed and some emojis/symbols/

facemarks that cannot be entered depending on the screen you operate.

Character Input (Software Keyboard)

Switching Software Keyboards

Tap the character entry field while INFOBAR C01 is displayed
horizontally to display the software keyboard and enter characters by
tapping keys on the screen.
To display the software keyboard while INFOBAR C01 is displayed
vertically, on the character entry screen, long-touch the character
entry mode key [Change settings [Display/Layout settings [enable
Always show keyboard.
The following software keyboards are available for the INFOBAR C01.

QWERTY You can enter a displayed character by tapping the

character entry key. Use romaji for entry.

12Key You can enter a character, changing characters by

repeatedly tapping the character entry key.

A On the character entry screen, [Change input UI

[Set 12 keyboard/Set QWERTY keyboard [OK.

■ Flick input

When the software keyboard is “12 Key”, you can enter a desired
character by flicking the key up, down, left or right without tapping the
key repeatedly.
By tapping a key, the candidates that can be entered by flick input are
displayed. By flicking the key in the direction of a desired character
being displayed, the character is entered in the character entry area.
For example, you can enter “A” by only tapping , and you can
enter “B” by flicking left.

36

Keep touching

Flick left

Viewing the Character Entry Screen

Learning the Basics

《Character entry screen (QWERTY)》

《Character entry screen (12 Key)》

A Character entry area
B Prediction candidates list/Relational prediction candidates list/

Normal conversion candidates list

If the word prediction function is enabled, the prediction
candidates list is displayed when characters are entered. If the
relational prediction function is enabled, the relational prediction
candidates list is displayed when an entry is selected from the
prediction candidates list.
Enter characters and tap to display the normal conversion
candidates list.

37

• You can enlarge the candidates list area by tapping . Tap
to return it to the original display.

C Software keyboard

You can enter a character assigned to each key.

D Shift key

You can switch uppercase characters entry and lowercase
characters entry. The display changes as follows each time you
tap it.

Learning the Basics

: Lowercase character entry
: Uppercase character entry

: Uppercase character entry lock
You can switch the symbols to enter by tapping the key in numeric
entry.

E Character entry mode key

When you switch the character types, the display changes as
follows.

: Kanji
: Half-width alphabet
: Half-width numeric
: Half-width Katakana
: Full-width alphabet
: Full-width numeric
: Full-width Katakana

: Character code

• Long-touch the character entry mode key to switch keyboards.

“12Key” at the bottom of the character entry mode key is a
keyboard to be switched when you long-touch the key. While
using the 12Key keyboard, “QWERTY” appears.

F Multiple key

The display is changed depending on the application or entering
item. You can switch the entry filed or display the menu etc. by
tapping the key.

38

G Delete key

Deletes the selected character or the character on the left of the
cursor. When the cursor is at the beginning, the character on the
right of the cursor is deleted.

H Emoji, Symbol and Facemark key/Kana and Alphanumeric key

: Displays the emoji/symbol/facemark list.

: Displays katakana, alphabet, number and predicted date

and time assigned to the entered key as conversion
candidates.
･ Tap to return to the previous screen.

I Setting key

The iWnn IME menu is displayed.

J Space key/Normal conversion key

: Enters a space.
: Displays the normal conversion candidates list.

K Cursor key

Moves the cursor to the left and right. Change the range of the
characters for character input and conversion.

L OK key/Line feed key

: Determines the entering characters.
: Inserts a line feed at the cursor position.

• If you long-touch OK key/Line feed key, the character entry
finishes and the character entry screen is closed.

• The display is changed depending on the application or entering
item.

M Reverse toggle key/Undo key

: Displays the characters assigned to the same key in the

reverse rotation.

: You can cancel the last operation such as returning the

determined characters to the undetermined state by
tapping the key.

N Settings key/Space key/Normal conversion key

: Displays iWnn IME menu.
: Enters a space.

･ Appears in alphabet and katakana entry.

: Displays the normal conversion candidates list.

O Space key/Uppercase/Lowercase characters switch key

• While the prediction candidates list/relational prediction candidates list/

: Enters a space.
: You can switch the entered alphabet to the uppercase/

lowercase one.

: You can switch the entered character to the uppercase/

lowercase one, add dakuten/handakuten to the
character, etc.

normal conversion candidates list is not displayed, tap ^ to hide the
keyboard.

Switching Character Entry Modes

A On the character entry screen,

[Change input mode.

B Select the character type.

• The character type is switched in order of “Half-width alphabet”

[“Half-width numeric” [“Kanji” each time you tap the character entry
mode key.

• Some character modes cannot be used depending on the screen or the

application.

Entering Emoji/Symbol/Facemark

A On the character entry screen, .

Learning the Basics

《Emoji/Symbol/Facemark list screen》

A Character switch tab

Switches the emoji/symbol/facemark.

B Emoji/Symbol/Facemark list

Displays the emoji/symbol/facemark list screen for each
category.

• Long-touch a facemark to edit it. However, facemarks in
History cannot be edited.

C Close key

Returns to the character entry screen.

D Page switch key

Displays the previous/next categories or pages.

E Character entry mode switch key

:Displays emojis converted automatically when sent

to a cell phone of other carrier.
:Displays normal emojis.
:Displays full-width symbols.
:Displays half-width symbols.

39

F Delete key

Deletes the selected character or the character on the left of
the cursor. When the cursor is at the beginning, the character
on the right of the cursor is deleted.

B Select an emoji/a symbol/facemark.

• There are some lists that cannot be displayed and some emojis/symbols/

facemarks that cannot be entered depending on the screen you operate.

Switching Input Software

Learning the Basics

A On the character entry screen, long-touch the

character entry screen [Input method.

B Select an input software.

• When using an installed application, enable it in Language & keyboard in

advance. Refer to “Using Android Market” to install an application.

40

Making a Call

A On the iida Home, Phone.

《Phone number entry screen》

A Phone number entry field

Enter numbers of up to 32-digit.

B Address book key

Make a call by selecting a contact information from the
address book. Or you can register the entered phone number
to the address book.

C Call key

Make a call. Also, if there is an outgoing history, the latest
outgoing history is entered by tapping when the phone
number has not been entered.

D Screen switching tab

Switches the phone number entry screen/incoming history list
screen/outgoing history list screen.

E Delete key

Deletes a single-digit on the left side of the cursor. If you
long-touch it, all the numbers on the left side of the cursor are
deleted and all the numbers are deleted when there is no
number on the left side of the cursor.

B Enter a phone number.

When calling to a fixed-line phone, enter the phone number starting
with the area code even if you are in the same area.

C Call [Talk.

Press u or d during a call to adjust the other party’s voice.

D End call.

• Also, you can make a call by entering the phone number on the iida Home/

widget Home.

• If you cover the screen while dialing/calling, it may be turned off depending

on the orientation of the INFOBAR C01.

• The call fees when calling with “1401” will be subtracted from the balance

registered by purchasing the au prepaid card.

• You can play the answering/voice mail saved by the Answering Service by

holding 1 down without entering the phone number on the phone
number entry screen.

• Note that even if you cover the mouthpiece, the sound can be conveyed to

the other party.

• Even if, on the iida Home, tap Settings [Wireless & networks [Mark Offline

mode, you can call to the emergency number (110, 119, 118) and the

Customer Service Center (157).

• If you want to return to the calling screen after activating another application

during a call, execute the following operations.

• Tap # to return to the iida Home, activate Phone and tap Return to call in

progress.

• Tap the status bar and tap Current call.

Phone

41

Dial services available from au phones

• The following dial services are available.

• Call with fixed-line phones all over Japan

• Call with cell phones, PHS, and car phones all over Japan

• 010 (au international call service: Subscription is unnecessary)

• 171 (Disaster emergency message dial)

• 177 (Weather forecast: The area code is necessary)

• 117 (Time signal)

• 104 (Directory assistance)

• 115 (Sending telegram)

• 110 (Emergency call to Police)

• 119 (Emergency call to Fir e and Ambulance)

• 118 (Emergency call to Regional Coast Guard)

• 157 (Customer Service Center)

Phone

• Maritime telephone

* The numbers are e mergency call numbers. The INFOBAR C01 notifies yo ur present

location to the emergency call destination with a signal from a base station when you
call to the agency that received the emergency ca ll.

• The following NTT services are unavailable.

• Collect call

• Message service

• Dial Q2

• 116 (NTT business information)

*

*

*

Making an International Call (au International Call Service)

Available without any additional application from the INFOBAR C01.

Example: To call 212-123-XXXX in the USA from the INFOBAR C01

A On the iida Home, Phone.

B Enter the international access code “001010” or

“010”.

Hold 0 down to enter “+” and “001010” is automatically added
when calling.

42

C Enter the country code of America “1”.

D Enter the area code “212”.

If the area code starts with “0”, dial it without including the “0” (There
are some exceptions such as fixed-line phones in some countries or
regions including Italy and Moscow).

E Enter the phone number of the other party “123XXXX”

[Call.

• The monthly limit fee is set for the au International Call Service. The au

International Call Service is unavailable from when the limit fee is confirmed
to be exceeded until the end of the same month.

• Even if you cannot use the service by exceeding the limit fee, you can use

from the first day of the next month. Also, you can use the domestic call as
usual while the service is stopped.

• The international call fee is charged together with other monthly fees from

au.

• If you do not wish to use the service, you can set not to use the au

International Call Service.
For au International Call Service:
From au phones 157 (area code not required) (toll free)
From fixed-line phones 0077-7-111 (toll free)
Open 9:00 to 20:00 (everyday)

Answering a Call

Answering an Incoming Call

A Slide to the right during an incoming call.

When you get an incoming call while the backlight illuminates (except
for when the unlock screen is displayed), tap Answer.

B Talk [End call.

Putting the Call on Hold

A Slide to the left during an incoming call.

When you get an incoming call while the backlight illuminates (except
when the unlock screen is displayed), tap Answer Holding.
The call is put on hold. The other party will hear voice guidance
indicating that the call is put on hold.

B Answer while the call is put on hold.

The hold state is released.

• The call fee is charged on the other party who has made a call to you while

the call is put on hold as well.

• If you disable the hold state once, you cannot put the call on hold again.

• You can put the call on hold only when Area settings is set to Japan.

Answering with the Message of Answering
Memo

You can answer a call with the message of the Answering memo and
record the other party’s message.

A e [Absence Memo during an incoming call.

Tap e while recording an Answering memo [Rcv. ON/Rcv. OFF to
turn on/off the other party’s voice.

Returning a Call (Outgoing History/ Incoming History)

A On the iida Home, Phone

[Outgoing History/Incoming History.

《Outgoing history list screen》

A Called/Received date and time
B Contents of the phone number/name/reason of user unset call/

network service

C Image (Face) registered in address book
D Make a call icon

Tap to make a call.

E Group icon

The histories are collected in a group when the outgoing
histories/incoming histories from the same party are
continued. Tap a group icon to switch displaying/hiding of the
history in the group.

《Incoming history list screen》

Phone

43

F Talk time
G Incoming call status icon

: Normal incoming call
: Missed call
: Missed call (One-ring call*)
: Rejecting call

H Calling time

* The missed call cut off in approximately 3 seconds is considered as one-ring call. Note

that it may make customers call back to connect to malicious paid programs.

B Select the entry to call back.

The outgoing history/incoming history detail screen is displayed.

Phone

C Call.

You can tap Mail to create an SMS (C-mail).

• The INFOBAR C01 can store up to 100 entries in each of the outgoing and

incoming histories. If the history exceeds 100 entries, the exceeded entries
are automatically deleted from the oldest one. The number of the saved
entries may be reduced depending on the amount of free space.

Turning On Manner Mode

Set not to disturb others around you in public places.

A On the iida Home, Settings [Sound settings

[Manner mode.

B Select Manner mode.

The ring tone/receiving tone/operation sound does not sound when the
Manner mode is set. Also, the vibrator when an incoming call or a mail
message is received does not operate when Drive manner mode or
Silent manner mode is set.
The answering message is fixed to Drive, the answering time is fixed to

3secs and the Answering memo is fixed to ON when the Drive manner
mode is set.

44

• The use of cell phones while driving a car/motorcycle is dangerous and is

prohibited by law. Set Manner mode to Drive manner mode while driving or
riding.

• Hold down f for at least two seconds [Manner mode or hold down

d on the unlock screen/iida Home/widget Home to enable/disable

Manner mode.

• Even in Manner mode, a shutter sound, recording start/end tone of the

camera or recording start/end tone of th e voice recorder are operated.

• When playing the data in Contents Manager or checking the function setting

by playing the data in Manner mode, the data is played on mute.
Depending on the function, you can adjust the volume by pressing u/
d while playing the data.

Turning On the Answering Memo

When you cannot answer calls, this function automatically plays a
message and allows callers to record messages.

A On the iida Home, Settings [Call settings

[Call/Ans Memo [Answering memo setting.

• The INFOBAR C01 can record a maximum of ten messages of up to

approximately 60 seconds per message. When ten messages have already
been recorded, the messages that are already played but not protected are
deleted from the oldest one. When all of them have not been played or are
protected, the Answering memo does not answer the call.

Playing a Message in Answering Memo

A On the iida Home, Settings [Call settings

[Call/Ans Memo [Answering Memo List.

《Answering memo list screen》

A Icons to indicate the playing status of the Answering memo

: Answering memo which has not been played (red)
: Answering memo which has already been played (green)

Icon of the protected Answering memo has .

B Other party’s name/phone number/reason of user unset call
C Date and time when the Answering memo is recorded

B Select the Answering memo to play.

The Answering memo is played.

Stop Stop playing the Answering memo.
On/Off Protect/Unprotect the Answering memo not

to be automatically deleted.

Delete Delete the Answering memo being played.

Speaker on/
Speaker off

• When multiple Answering memos are recorded, tap / while

playing a message to play the previous/next Answering memo.

The Answering memo can be heard on the
speaker/earpiece.

Phone

45

Adding an Address Book Entry

A On the iida Home, Address Book [e

[Add new entry.

If you have set an account, select the destination to register a contact
to.

B

(Face) Register the image of the face.

(Whole body) Register the image of the whole body.
Family name Register the family name.
Given name Register the given name.
Read last Register “reading” of the family name.

Address Book

Read first Register “reading” of the given name.

Phone number Register the phone number.
Mail Register the mail address.
mixi Register the information of a person

Twitter Register the information of a person who you

Chat Register the chat address.
Group setting Set the group.
Birthday Register the birthday.
Nickname Register the nickname.
Postal Register the address.
GPS Register the GPS information.
Organization Register the company/part/post.
Website Register the URL.
Memo Register the memo.
Event Register the date.
Internet call Register the address for the internet calling.

46

• The “reading” is automatically entered
when the family name is entered.

• The “reading” is automatically entered
when the given name is entered.

registered in the friend list of mixi.

follow on Twitter.

Ring Set Set the sound, the lamp and the vibration

when an incoming call is received.

Save [Yes.

C

• Tap to display the entry items which are not displayed.

• Tap / to add/delete the item.

• If the phone number is for a fixed-line phone, enter the phone number

starting with the area code.

• If you save multiple phone numbers/mail addresses, tap to change it to

so that you can set the phone number/mail address for usual use.

• Depending on an item, you can change its type. Tap the icon displayed on

the left of the item and select a type. By tapping Custom when you change
the type, you can save the entered string as a type.

• For the chat address type, set the application which is activated when the

operation (on the address book details screen, tap ) is executed.

• If you save the name in the following characters, it is displayed in order of

given name, and family name on the address book.

• Half-width alphabet only or half-width alphabet and half-width numeric for
given name and family name

• Half-width alphabet only or half-width alphabet and half-width numeric for
family name/Kanji only or Kanji and half-width alphanumeric for given
name

• To register GPS information, enable Use wireless networks/Use GPS satellites in

advance. On the iida Home, tap Settings [Location & security [Check Use
wireless networks/Use GPS satellites to enable it.

• If the other party’s phone number is not notified, Ring Set is not enabled.

Using an Address Book

Viewing the Address Book Details Screen

A On the iida Home, Address Book

[Select a contact information.

Tap image (face) on the address book list screen (newly arrived
order).

《Address book details screen》

A Name

Tap to display the icon of the available applications.

B Image (Whole body)
C Registered contents

Slide upward to check or use all the registered contents.

D Speech bubble

Displays messages such as incoming calls and mixi from the
contact. If you tap, you can use the message pack.

E Action icons

Tap to retrieve the following functions.

: Call to the selected phone number.
: Create an SMS (C-mail) message using the selected

phone number as an address.

: Create a mail message using the selected mail address

as an address.

: The application set in the chat address type starts and

start a chat with the selected chat address.
When a corresponding application has not been
installed, you have not signed in your account, etc., the
application may not start.

: The Google map starts based on the selected address/

GPS information.

: Displays the mail creation screen on which the GPS

information is entered in the message.
: Displays the site of the selected URL.
: Call to the address for the selected internet calling.

F Picture field

You can register the people category of pictures and display
the data.
Long-touch the picture field [tap Yes to cancel the
registration.

Address Book

47

Using Phone Number

A On the iida Home, Address Book

[Select a contact information.

■ When calling/sending to a phone number

B Select the phone number.

C

Call Call to the selected phone number.
Edit and call Displays the phone number entry screen with

Create mail Create an SMS (C-mail) message using the

Call added

Address Book

special number

■ When setting a phone number

the selected phone number entered.

selected phone number as an address.
Add the specific number to the selected

phone number.

B Long-touch the phone number.
C

Set main phone
number
Create shortcut Create a shortcut to call to the selected

Set the phone number for usual use.

phone number or to activate SMS (C-mail)
message using the selected phone number
as an address.

Using Mail Address

A

On the iida Home, Address Book
[Select a contact information.

■ When sending a mail message to a mail address

B Select the mail address.

■ When setting a mail address

B Long-touch the mail address.
C

Set main mail
address
Create shortcut Create a shortcut to activate mail message

Set the mail address for usual use.

using the selected mail address as an
address.

48

Using E-mail

E-mail ([email protected]) is a service that enables you to exchange
e-mails with other cell phones and with PCs that support e-mail. In
addition to text messages, you can also send data such as photos
and movies by e-mail.

• Initial settings must be done in advance to use e-mail. For details,
refer to Setting Guide (Japanese).

• Subscription to IS NET is required to use e-mail. Those who did not
subscribe to the service at the time of the purchase can contact an
au shop or Customer Service Center for the service.

• E-mail can be used overseas, too. For details, refer to Global Passport

Owner’s Guide (Japanese).

• The packet communication charge for sending and receiving e-mail varies

according to the amount of data sent and received. For using overseas,
high charges can be incurred. For details, refer to the au comprehensive
catalogue or au homepage.

• Sending and receiving e-mails may take some time if attached data are

included in them or depending on radio wave status of the area where the
phone is used.

Sending E-mail Messages

A On the iida Home, E-mail [Create new.

The sending mail creation screen is displayed.

《Sending mail creation screen》

B .

You can also enter an address directly by tapping the address entry
field.

C

Address
book
Address
group

Enter an e-mail address in the address book as
the destination.
Enter the e-mail addresses of contacts
registered in a group in the address book as the
destination.

• If the e-mail addresses of contacts registered
in a group exceed the limit of the destination,
the e-mail addresses of up to the limit are
entered.

• Tap Add group by Friends Note to create a
group.

Mail

49

Receive
history

Enter an e-mail address as the destination by
selecting one included in the list of entries from
the mail receive history.

• Tap e [Delete [Select an e-mail
address [Delete [Delete to delete the
history.

Send history Enter an e-mail address as the destination by

selecting one included in the list of entries from
the mail send history.

• Tap e [Delete [Select an e-mail
address [Delete [Delete to delete the
history.

Profile Enter an e-mail address as the destination by

selecting one registered in the profile.

Paste Paste a copied e-mail address.

D Tap the subject entry field [Enter the subject.

Mail

Up to 50 full-width/100 half-width characters can be entered in the
subject entry field.

E Tap the message entry field [Enter the message

[Done.

Up to approximately 5,000 full-width/10,000 half-width characters can
be entered in the message entry field.

F Send [Send.

• The decoration animation is not supported.

• You cannot enter half-width katakana and half-width symbols (−(long
vowel)゛(dakuten)゜(handakuten)、。・「」) in the subject/message entry field.

• You can send a maximum of 1,000 e-mails per day, which is the total

number of e-mails with all the destinations combined.

• You can send an e-mail to a maximum of 30 different destinations at the
same time (including To/Cc/Bcc. Up to 64 half-width characters per
message).

50

• If you send pictograms of au version to cell phones of other carriers, those

pictograms will be converted to other carriers’ version before they are
received by the other party.

* Some pictograms will n ot be converted.

• Part of pictograms sent to cell phones of different models, PCs, etc. may not

be displayed properly on the receiving side.

• You can save the e-mail in process of composition into “Unsent” by tapping

Save on the sending mail creation screen.

Receiving E-mail Messages

A An e-mail message is received.

After an e-mail message is received, appears on the status bar,
and the e-mail ring tone sounds.

• The e-mail address, name and subject are displayed on the status
bar. If the name of the sender has been set for the received e-mail,
the set name is displayed. If the e-mail address of the sender has
already been registered in the address book, the name registered in
the address book takes priority.

《Reception complete screen》

B Tap the status bar.

C E-mail.

The e-mail top screen is displayed.

D Tap Inbox or a folder [Select the received e-mail.

The received mail message screen is displayed.

• E-mail messages will be received in the background even during operations

of e-mail or other functions. appears on the status bar, and the e-mail
ring tone sounds. On the iida Home, tap E-mail [e [E-mail settings
[Receive/display settings [Uncheck Auto-receive. After that, e-mail
messages will not be received in the background.

• When Auto-receive is disabled or the e-mail reception fails, the e-mail ring

tone sounds and is displayed. On the iida Home, tap E-mail [Mail
check to receive the e-mail.

• Packet communication charges may apply even if e-mail messages are not

properly received depending on the reception status and data received.

• The maximum data capacity of a message that can be received is

approximately 5,000 full-width/10,000 half-width characters (approximately
10 KB). If the number of the characters exceeds the capacity, a notice to
inform you that the exceeded characters have not been received will be
displayed.

• Some contents of the received e-mail message will not be properly

displayed.

Receiving Mail Message by Inquiring

If you set the cell phone not to receive mail messages automatically
(on the iida Home, tap E-mail [e [E-mail settings [Receive/
display settings [Uncheck Auto-receive) or the e-mail reception fails,
you can receive the mail messages by inquiring them.

A On the iida Home, E-mail [Mail check.

Check whether new e-mail messages have been received.

Reading Received E-mail Messages

Received e-mail messages are saved in “Inbox”. Sent e-mail
messages are saved in “Outbox”. If the received e-mail messages
and sent e-mail messages match a condition for sorting mail
messages, they are saved in the set folders. E-mail messages saved
without being sent and failed to be sent are saved in “Unsent”.

A On the iida Home, E-mail.

Mail

《E-mail top screen》

A Folder

The created folder is displayed.

B Inbox

When there are new mails, the number of the mails appears in
red, and it changes to blue after you check the mails.

C Outbox

51

D Unsent

When there are unsent e-mails, the number of the e-mails
appears in blue (it changes to red when there are e-mails
failed to be sent).

E Template
F Create new folder
G Action bar

B Select a box/folder.

■ Inbox

■ Outbox

Mail

《Mail list screen (two line display)》

52

《Mail list screen (message

preview display)》

《Mail list screen (two line display)》

■ Unsent

《Mail list screen (two line display)》

《Mail list screen (message

preview display)》

《Mail list screen (message

preview display)》

■ Folder

《Mail list screen (two line display)》

《Mail list screen (message

preview display)》

A : Unopened e-mail

: E-mail with its message not received

: E-mail with its message not received because there is no mail

on the server/E-mail failed to be sent/E-mail failed to be
forwarded because there is no original mail (received mail) on
the server

B Subject
C Name or e-mail address of the destination/sender

If the e-mail address is registered in the address book, the name
registered in the address book is displayed.
If the name of the sender is set for the received e-mail, the set
name is displayed.

• If an e-mail address has already been registered in the address
book, the name registered in the address book takes priority.

If the e-mail address is not registered in the address book and the
name of the sender is not set for the received e-mail, the e-mail
address is displayed.

D : E-mail which has been replied/E-mail for replying

: E-mail which has been forwarded/E-mail for forwarding

: E-mail which has been replied and forwarded

E Two line display/Message preview display switching key

Appears only on the portrait display. Message preview display is
always applied for the landscape display.

F Attached data exist
G Protected e-mail
H Flags exist
I Action bar
J Message preview
K Receiving/Sending switching slider

Switches and displays the received mail list and sent mail list in the
folder.

C Select an e-mail.

《Received mail message screen》 《Sent mail message screen》

Mail

53

《Unsent mail message screen》

A Name or e-mail address of the sender
B / / : Name or e-mail address of the destination

Mail

• is displayed when there are multiple destinations. Tap it to
display all e-mail addresses.

C : E-mail with its message not received

: E-mail with its message not received because there is no mail

on the server/E-mail failed to be sent/E-mail failed to be
forwarded because there is no original mail (received mail) on
the server

D : E-mail which has been replied/E-mail for replying

: E-mail which has been forwarded/E-mail for forwarding

: E-mail which has been replied and forwarded

E Subject
F : Attached data which has been received/Attached data which

has been sent/Unsent attached data

: Attached data which has not been received

• is displayed when there are multiple attached data. Tap it to
display all attached data.

54

G Message
H Displays next e-mail/previous e-mail

• Alternatively, flick the message display area to the left/right to
display the next e-mail/previous e-mail.

I Attached data exist
J Flags exist
K Protected e-mail
L Action bar

Reply: Create an e-mail for replying.
Forward: Create an e-mail for forwarding.
Protect/Unprotect: Protect/Unprotect the e-mail.
Flag/Unflag: Flag/Unflag the e-mail.
Resend: Send the same e-mail as you have sent again.
Edit copy: Copy and edit the e-mail.
Edit: Edit the e-mail.

• E-mails which have not reached the other party because their destinations

are not identified are saved in “Outbox”.

• On the e-mail top screen, tap e [au one mail [au one mail Top to use

au one mail.

• If the capacity of “Inbox” is exceeded, the oldest opened mail will be

deleted automatically. However, unopened e-mails, protected e-mails and
e-mails with its message not received will not be deleted.

• If all the mails in “Inbox” are unopened and the capacity of “Inbox” is

exceeded, you cannot receive a new mail.

• If the capacity of “Outbox” or “Unsent” is exceeded, the oldest sent mail will

be deleted automatically. If there are no sent mails which can be deleted, a
mail is deleted in order of e-mails failed to be forwarded with no original mail
on the server, e-mails failed to be sent and unsent e-mails.

Setting Mail Filters

登録

Mail filters have functions to receive and reject specific e-mail
messages and to reject e-mail messages spoofing cell phones or PHSs.

※Th e function of the mail filters is to be expanded. The details of the expanded function and time

for the function expansion are to be released on the au homepage.

A On the iida Home, E-mail [e [E-mail settings

[Other settings [OK.

■ Setting the mail filter as recommended

B (See Recommended Settings)

オススメの設定はこちら

[ (Register).

Set the mail filter that enables to reject spoofing or auto-forwarded mail
messages, and to receive mail messages from cell phones, PHSs or
PCs.

■ Setting details of the mail filter

B (Mail Filter)

迷惑メールフィルター

[Tap the security code entry field
[Enter your security code
[ (Send).

送信

The mail filter screen is displayed.

C

カンタン設定

(Simple Settings)

詳細設定

(Advanced
Settings)

1.「携帯」「PHS」「PC」メールを受信

(1. Receive Mail Messages from Cell
Phone, PHS or PC)

Reject spoofing or auto-forwarded mail
messages, and receive mail messages
from cell phones, PHSs or PCs.

2.「携帯」「PHS」メールのみを受信

(2. Receive only Mail Messages from Cell
Phone or PHS)

Reject mail messages from PCs, spoofing
mail messages or auto-forwarded mail
messages, and receive mail messages
from cell phones or PHSs.

一括指定受信

(Collective Receive Setting)

Receive or reject all mail messages from
the Internet or cell phones.

なりすまし規制

(Spoof Restriction)

Reject mail messages sent with an alleged
sender address. You can set the following
levels; 高 (High), 中 (Medium), 低 (Low).

指定拒否リスト設定

(Reject Mail Address List Setting)

Reject mail messages from certain e-mail
addresses, domains or parts of addresses
to the left of “@” that are contained in the
specified address list.

Mail

55

Mail

詳細設定

(Advanced
Settings)

設定確認／設定
解除

(Check Settings/
Release
Settings)

指定受信リスト設定

(Allowed Address List Setting)

Prioritize reception of mail messages from
certain e-mail addresses, domains or parts
of addresses to the left of “@” that are
contained in the specified address list.

• To block e-mail messages from
addresses other than the specified ones,
unmark all items in
(Collective Receive Setting).

一括指定受信

指定受信リスト設定（なりすまし・転送メー
ル許可）

(Allowed Address List Setting (Spoofing or
Forwarded Mail Messages))

Avoid the mail block due to

なりすまし規制

setting, and receive auto-forwarded mail

(Spoof Restriction)

messages.

HTMLメール規制
(HTML Mail Restriction)

Reject e-mail messages in HTML format.

URLリンク規制
(URL Link Restriction)

Reject e-mail messages that include a URL.

拒否通知メール返信設定

(Block Mail Notification Setting)

Set whether to send a receiver error
(address unknown) mail message to the

sender of the rejected e-mail message.
Check the setting status of the mail filters
and release all the settings at one time.

PC設定用ワンタ
イムパスワード
発行

(Issue One Time

Issue a one time password to set the mail
filter on your PC.

Password for PC
Setting)

設定にあたって

(Notes on Setting

Display the explanation for setting mail
filters.

Mail Filter)

• If the security code is incorrectly entered three times consecutively during a

single day, the mail filter setting operation will be disabled until the next day.

• Note that you cannot receive e-mail messages once rejected by mail filters.

Be careful when you set mail filters.

• Mail filters functions apply to new e-mail messages in order of the

followings.
指定受信リスト設定（なりすまし・転送メール許可） (Allowed Address List
Setting (Spoofing or Forwarded Mail Messages)) ＞なりすまし規制 (Spoof
Restriction) ＞指定拒否リスト設定 (Reject Mail Address List Setting) ＞指定
受信リスト設定 (Allowed Address List Setting) ＞HTMLメール規制 (HTML
Mail Restriction) ＞URLリンク規制 (URL Link Restriction)＞一括指定受信
(Collective Receive Setting)

• 指定受信リスト設定（なりすまし・転送メール許可） (Allowed Address List

Setting (Spoofing or Forwarded Mail Messages)) is a function to prevent
auto-forwarded e-mail messages from being rejected because of the setting
of なりすまし規制 (Spoof Restriction). E-mail messages whose mail
addresses are included in To (destination) or Cc (Carbon Copy) can be
received without being restricted by registering an address of the automatic
forwarding setting source to 指定受信リスト設定（なりすまし・転送メール許
可） (Allowed Address List Setting (Spoofing or Forwarded Mail Messages)).

* Note that this func tion does not apply to the e-mail messages (includ ing some e-mail

magazines) whose mail address is included only in Bcc (Blind Carbon Copy).

• 拒否通知メール返信設定 (Block Mail Notification Setting) is automatically

返信する

set to (Reply) first time you set the mail filters. Also, spoofing
e-mail messages will not be replied to even if (Reply) is set.

返信する

56

• If you set URLリンク規制 (URL Link Restriction), you may not receive e-mail

messages whose message entry field includes a URL such as e-mail
magazines and information providing e-mail messages, or member
subscriptions to some cell phone sites etc. may not be available.

• If you set HTMLメール規制 (HTML Mail Restriction), e-mail messages in the

HTML format may not be received when they are among other e-mail
messages sent from e-mail magazines or PCs. Also, decorated e-mail
messages from cell phones and PHSs can be received even if HTMLメール

規制 (HTML Mail Restriction) is set.

• なりすまし規制 (Spoof Restriction) function judges whether received e-mail

messages are definitely from no other domains and restricts any e-mail
message whose domains it considers may be spoofing messages domains.
This function is limited to the occasions where the providers, e-mail
distributing companies, etc. controlling the domains written on the header of
the received e-mail messages are setting the domain authentication (SPF
record). For details on the setting conditions of the domain authentication,
contact the respective provider, e-mail distributing company, etc.

* While e-ma il messages received by a PC etc. are being forwarded, the transmissions

may be blocked after those messages are judged not to be from p roper domains. In that
case, register an address of the automatic forwarding so urce to 指定受信リスト設定（な
りすまし・転送メール許可） (Allowed Address List Setting (Spoofing or Forwarded Mail
Messages)).

■ Setting Mail Filters Using a PC

Mail filters can also be set using your PC. Access PCからメールフィ
ルター設定 (Mail Filter Settings From PC) (in Japanese only) inside the

screen of 迷惑メールでお困りの方へ (For Customers Bothered By
Unwanted Spam) (in Japanese only) on the au homepage and set the
mail filter after entering a one time password for PC setting.
You can check the one time password for PC setting by accessing PC
設定用ワンタイムパスワード発行 (Issue One Time Password for PC
Setting) in the mail filter screen.
Connect to the mail filter setting from a PC within 15 minutes after
issuance of the one time password for PC setting. When 15 minutes
have passed after that, the one time password for PC setting will
become invalid.

Using SMS (C-mail)

SMS (C-mail) is a service that uses phone numbers as the destination
to exchange messages between cell phones.

Sending SMS (C-mail) Messages

You can send a message consisting of kanji/hiragana/katakana/
alphanumeric/symbols/pictograms/facemarks. When sending is
completed, you will be noticed whether the mail is received by the
other party.

A On the iida Home, SMS(C-mail) [Create new.

The sending mail creation screen is displayed.

Mail

《Sending mail creation screen》

B .

You can also enter a phone number as the destination directly by
tapping the destination entry field.

57

C

Address
book

Enter a phone number in the address book as
the destination.

Send history Enter a phone number as the destination by

selecting one included in the list of entries from

the send history.
Receive
history

Enter a phone number as the destination by

selecting one included in the list of entries from

the receive history.

Tap the message entry field [Enter the message.

D

Up to 70 full-width/140 half-width characters can be entered in the
message entry field.

E Send.

After you send a mail, a message indicating that the mail is received
by the other party or the mail is stored is displayed. The sent mail is
saved in “Outbox”.

Mail

• On the sending mail creation screen, tap Save. After that, the mail message

is saved in “Outbox” without being sent.

• SMSs (C-mails) will be kept (stored) in the SMS (C-mail) center for up to 72

hours. SMSs (C-mails) kept in the SMS (C-mail) center beyond that period
will automatically be deleted. Also, there is no limit for the number of SMSs
(C-mails) kept.

• SMSs (C-mails) may not be kept in the SMS (C-mail) center depending on

usage of the receiving users or types of the cell phones of the sending
users.

• SMSs (C-mails) stored in the SMS (C-mail) center will be sent in the

following conditions.

• Immediately after an SMS (C-mail) is stored: All the SMSs (C-mails) stored
in the SMS (C-mail) center will be sent every time a new SMS (C-mail) is
stored in the SMS (C-mail) center.

• Via the retry function: An SMS (C-mail) will be sent via the retry function
which keeps sending one repeatedly for a maximum of 72 hours if the
SMS (C-mail) failed to be sent immediately after the SMS (C-mail) is
stored due to such reasons as the cell phone of the other party is out of
reach of radio waves and the power is turned off.

58

• When a call is ended: If an SMS (C-mail) failed to be sent immediately
after an SMS (C-mail) is stored, all the SMS (C-mail) stored in the SMS
(C-mail) center will be sent after the user ends a call with the INFOBAR
C01.

• The caller ID will be notified when an SMS (C-mail) is sent regardless of the

setting (on the iida Home, tap Settings [Call settings [Uncheck Send caller
ID).

• Part of pictograms sent to cell phones of different models may not be

displayed properly.

• Even when an SMS (C-mail) is successfully sent, Failed to send may appear

infrequently in a location where the signal is weak etc.

Receiving SMS (C-mail) Messages

A An SMS (C-mail) is received.

After an SMS (C-mail) is received, appears on the status bar, and
the mail ring tone sounds.

《Reception complete screen》

B Tap the status bar.

C Select the phone number or the name.

The received mail list screen is displayed.
If there are multiple unopened SMSs (C-mails), New message
(Xmessages) is displayed.

D Select the received SMS (C-mail).

The received mail message screen is displayed.

• Receiving SMS (C-mail) is free.

• In a received SMS (C-mail), you can check the phone number of the other

party who sent the SMS (C-mail).

• Depending on the received mail, some contents may not be displayed

properly.

Reading Received SMS (C-mail) Messages

Received SMS (C-mail) messages are saved in “Inbox”. Sent SMS
(C-mail) messages and SMS (C-mail) messages saved without being
sent are saved in “Outbox”.

A On the iida Home, SMS(C-mail).

• If there are unopened mails in “Inbox”, the total number of the mails
is displayed on the right side.

• If there are unsent mails or mails failed to be sent in “Outbox”, the
total number of the mails is displayed on the right side.

B Inbox/Outbox.

《Received mail list screen》

《SMS (C-mail) menu screen》

Mail

《Sent mail list screen》

59

A Keyword entry field
B : Unopened SMS (C-mail)

: SMS (C-mail) which has been replied

: SMS (C-mail) which has been checked for being received

: Unsent SMS (C-mail)

: SMS (C-mail) failed to be sent

C Message preview
D Name or phone number of the destination/sender

When the phone number is registered in the address book, the
name registered in the address book is displayed.

E Number of unopened mails/Number of mails in Inbox
F Protected SMS (C-mail)
G Number of mails unsent or failed to be sent/Number of mails in

Outbox

C Select an SMS (C-mail).

Mail

《Received mail message screen》 《Sent mail message screen》

A Phone number or name and phone number of the destination/

sender

If the phone number is registered in the address book, the name
registered in the address book is displayed.

B : SMS (C-mail) which has been replied

: SMS (C-mail) which has been checked for being received

: Unsent SMS (C-mail)

: SMS (C-mail) failed to be sent

C Message

Flick the message display area to the left/right to display the next
mail/previous mail.

D Protected SMS (C-mail)
E Action bar

• If the number of received mails exceeds its limit (1,000 mails), the oldest

mail will be deleted automatically in order of opened mails and unopened
mails. In that case, protected mails are the exception for the automatic
deletion. If the internal memory of the INFOBAR C01 is insufficient, the
automatic deletion will be performed even if the limit is not exceeded.

• If the number of sent mails exceeds its limit (1,000 mails), the oldest mail will

be deleted automatically in order of sent mails, mails failed to be sent and
unsent mails. In that case, protected mails are the exception for the
automatic deletion.

60

Rejecting Spam SMS (C-mail) Messages

auoneメールヘルプ

A On the iida Home, SMS(C-mail) [Inbox/Outbox [e

[Settings [SMS filter.

B

Reject
specified
Phone No.

Rejection
list

Reject
unknown
senders

Set whether to reject SMSs (C-mails) received
from the specified numbers.

Register phone numbers on Rejection list.

• Tap to select the entry method and register
phone numbers.

• Up to ten phone numbers can be registered.

• To delete the registered phone number, tap

Delete [Select a phone number to be deleted
[Delete [Yes.

• Even when you reject receiving by receiving
filter, the sender is supposed to send the mail
message correctly, and the charge applies.

Set whether to block SMS (C-mail) from any
phone number not saved in the address book.

Setting Account for PC-mail

You can use PC-mail by setting an account of au one mail etc.

• To use au one mail in PC-mail, acquiring au one mail account,
enabling IMAP setting, setting mail password are required in
advance. On the iida Home, tap au one for iida [
(Support Information) [ (au one mail help)
and set after confirming the contents of the help.
When you activate PC-mail for the first time, you need to register an
account. When the registration finishes, you can use the PC-mail.

サポート情報

A On the iida Home, PC-mail.
B Tap the address entry field [Enter a mail address.

C Tap the password entry field [Enter the password.

■ When setting a mail server automatically

D Next.

Set manually when the mail server of the mail account you use is not
automatically set.

E Tap the account name entry field

[Enter an account name.

F Tap your name entry field [Enter your name

[Done.

■ When setting a mail server manually

D Manual setup.

Confirm the setting of the receiving mail server and sending mail
server by contacting the provider you use in advance.

Mail

61

E Select an account type.

When setting by POP3 server, the PC-mail saved in the INFOBAR C01
terminal may be deleted depending on the provider you use. When
using the mail server supporting IMAP (Gmail, au one mail, etc.), set
by IMAP server.

F

User name/
Domain¥Username

Password Enter the password.
POP3 server/IMAP
server/Server
Port Enter the port number.
Security type Set when necessary.
Delete email from server Set whether to remain the received

IMAP path prefix Enter when necessary.
Use secure connection

Mail

(SSL)
Accept all SSL
certificates

Next.

G
H

SMTP server Enter the server information.
Port Enter the port number.
Security type Set when necessary.
Require sign-in. Set when necessary.

* Besides the ab ove mentioned items, the user information entry fiel d and password entry

field are displayed.

Enter the user information.

Enter the server information.

PC-mail in the server.

Set whether to use the SSL when
receiving PC-mails.
Set whether to accept all the SSL
certificates.

Enter the User name and Password
when enabling the setting.

I Next.

J

Inbox checking
frequency

Send email from this
account by default.

Notify me when email
arrives.

Next.

K

Set the interval to confirm to the
server whether a new PC-mail is
received.
Set to the priority account when
composing a PC-mail if multiple mail
accounts are set.

Set whether to display to the status
bar that a PC-mail is received.

L Tap the account name entry field

[Enter an account name.

M Tap your name entry field [Enter your name

[Done.

• When the account type is “Exchange”, entering “¥UsernameDomain” in the

“Domain¥Username” area is required depending on the provider. Contact
the administrator of the server for details.

62

Sending PC-mail Messages

A On the iida Home, PC-mail [e

[Compose.

E Send.

If you tap Save as draft, PC-mail is saved to draft without sending it.
If you tap Discard, PC-mail in process of composition is discarded.

Receiving PC-mail Messages

A PC-mail is received.

If PC-mail is received, appears on the status bar, and the mail ring
tone sounds.

B Tap the status bar.
C Select PC-mail information.

D Select the received PC-mail.

《PC-mail composition screen》

A Destination entry field
B Subject entry field
C Message entry field

B Tap the destination entry field

[Enter the destination.

If you enter a name or a mail address in the destination entry field, the
address book is automatically searched and the destination
candidates are displayed. Select one of them to set it as the
destination. After setting the destination, you can enter and add the
destination in a row.

C Tap the subject entry field [Enter the subject.
D Tap the message entry field [Enter the message.

Using Gmail

Gmail is a mail service provided by Google. You can send and receive
Gmail with the INFOBAR C01.

• Google account is required to use Gmail. For details on Google
account, refer to “Setting Up a Google Account”.

• On the iida Home, tap Settings [Accounts & sync to synchronize
Gmail saved in the server with one saved in the INFOBAR C01.

• For using Gmail, refer to Google homepage.

Mail

63

A On the iida Home, Gmail.

《Inbox tray screen》

A Tray/Label name, Number of unopened mail messages

Mail

Tap to display trays/labels as a list.

B Mail message
C Account name

Tap to display accounts as a list.

D Label

Displayed on a mail message for which a label is set.

E Attached file icon

Displayed on a mail message with files attached.

F Check box

Tap to make it marked and to display the menu.
Mark a mail message which you intend to make marked and
select the menu.

G Star icon

Tap to enable/disable the setting of starring a message.

Sending Gmail

A On the iida Home, Gmail [e [Compose.
B Tap the destination entry field

[Enter the destination.

C Tap the subject entry field [Enter the subject.
D Tap the message entry field [Enter the message.
E .

Receiving Gmail

A Gmail is received.

When Gmail is received, appears on the status bar, and the mail
ring tone sounds.

B Tap the status bar.
C Select mail information.

D Select the received mail.

The received mail message screen is displayed.

■ Replying/Forwarding Gmail

A On the received mail message screen,

[Reply/Reply all/Forward.

64

Viewing Sites with Browser

A On the iida Home, Browser.

The browser screen is displayed.
On the iida Home, tap au one for iida to display iida homepage for
Android all the time.

• When browsing a web page with a large amount of data, the application

may be terminated automatically.

Filtering function

• The filtering function blocks inappropriate web pages for young people.

On the iida Home, tap Settings [Wireless & networks [Filtering settings
[Yes [Enter a password [OK [Enter a password again [OK.

• The filtering function is not compatible with the application communication
and the Wi-Fi® connection. It is recommended to use the filtering function
of “ウイルスバスター (VirusBuster)” and “安心アプリ制限 (Restrict
Applications)”.

• The password used when enabling the filtering function is necessary
when disabling the setting. Be sure to keep the password.

• Even if you enable the filtering function, you can display the sites that you
displayed them while disabling the filtering function and caches remain.

Using Bookmarks/History

Displaying a Site from Bookmarks/History

A On the iida Home, Browser [ .

《Bookmarks/History screen》

A Bookmarks/History list

Displays the list of the bookmarks/history.

B “Bookmarks” tab

Displays the registered bookmarks.

C “Most visited” tab

Displays the viewing history of the site from the most
frequently viewed one.

D “History” tab

Displays the viewing history of the site.

B Select a bookmark/history.

• On the history screen, tap / to bookmark/delete the selected history.

Internet

65

Bookmarking a Web Page

Bookmark the displayed site.

A On the iida Home, Browser

[ [Add.

B OK.

• On the iida Home, tap Browser [ [Long-touch a bookmark [Delete

bookmark to delete the bookmark. Likewise, on the iida Home, tap Browser

[ [Most visited/History [Long-touch a most visited site/history
[Delete from bookmarks to delete the bookmark.

Internet

66

Using the Camera

INFOBAR C01 has a CMOS camera with approximately 8.04 effective
megapixels for shooting photos and recording movies.

• All the photos and movies shot/recorded are saved in a microSD
memory card. Insert a microSD memory card before using the
camera.

• The mobile light flashes in red while each camera mode is activated.

Cautions for Using the Camera

• If the camera lens is exposed to direct sunlight for a long time, the
internal color filter may discolor and it causes discoloration of shot
images.

• The quality of images may deteriorate when shot or saved after the
INFOBAR C01 has been left in a warm location for a long time.

• Although the camera is made of high-precision parts, some pixels
look constantly dark or bright. Further, blue, red, white dots, etc.
appear in images especially when shooting images in a very dark
place.

• Fingerprints, fats, etc. on the lens may cause the images to blur.
Wipe the lens with a soft cloth such as cloths for cleaning glasses
before shooting images. The lens may be damaged if you wipe it
strongly.

• Make sure that your fingers, hair, the straps of the INFOBAR C01,
etc. do not obscure the camera lens when shooting images. If the
straps interrupt you when shooting images, hold the straps with your
hand.

• Be careful of camera shakes. Hold the INFOBAR C01 tight or use
the self-timer function since such shakes may cause the images to
blur.
Be careful of camera shakes especially in a place without enough
light such as inside of a room.
Also, images may blur when the subject of the images moves.

• Before shooting images, make sure that the subject is completely
displayed. If you shoot images while moving the camera, the images
may blur.

• Indoor fluorescent lighting may cause flickers (too fine to be seen
with human’s naked eyes) to be detected and light fringes may be
displayed. This is not a malfunction.

• When shooting indoors, the display may become yellow. On the iida
Home, tap Camera [ [White Balance [Fluorescent/Tungsten
to solve this problem.

• When shooting images under incandescent lamps etc., the display
may become red. On the iida Home, tap Camera [ [White
Balance [Tungsten to solve this problem.

• Make sure that the microphone is not covered by your fingers etc.
when recording movies. Also, the quality of its sounds may
deteriorate depending on the voice volume and surrounding
environment during the recording.

• The color and brightness of the subject of images shot with the
INFOBAR C01 may differ from the actual color and brightness.
Because of the characteristics of the lens, some part of the images
may appear dark or light depending on the subject and light ray
while shooting. Also, note that some part of the subject in the images
may be distorted due to the usage of wide-angle lens.

• Purple lines and bars may be displayed on images while recording
strong light or shiny subject. This is not a malfunction.

Multimedia

67

• When you subject the camera to strong impacts when shooting
images, the images may be out of focus. In such case, reactivate
the camera.

• The following subjects may cause images to be out of focus.

･ Subjects with few contrasts such as solid color walls
･ Backlit subjects
･ Subjects reflecting light brightly such as shiny objects
･ Subjects with horizontal repetitive patterns such as blind
･ In the case when there are many subjects located at different

distances from the camera

･ Subjects in dark places
･ Subjects which move quickly

• Do not position the mobile light close to your eyes. Do not look at the
mobile light directly while it is on. Do not point on the mobile light
toward the eyes of others. It may harm eyesight.

• The tone for locking AF and the shutter tone sounds, even if you set
Manner mode. The tone for starting and stopping movies also
sounds. You cannot change the tone volume.

• While the camera is operating, such as activating the camera, you
may hear small sound made from the operation of the inner parts.

Multimedia

This is not a malfunction.

• The INFOBAR C01 may be warm after displaying the photo monitor
screen or recording movies repeatedly for a long time. Be careful of
touching for a long time, which may result in a low temperature burn.
Also you may not be able to use the camera when the temperature
of the INFOBAR C01 is increased.

• When shooting images of strong light sources such as the sun or a
lamp, the images may appear dark or distorted.

• When shooting images of moving subjects or changing the place
from light place to dark place, the display may whiten or darken for a
moment. Also, the display may be distorted etc. for a moment.

68

• When shooting images in a dark place, noises may increase and
shot photos may become rough etc.

• Note that if the self-timer shooting is set and the INFOBAR C01 is left
on an unstable place, it may fall due to the vibration etc. activated
when an incoming call is received etc.

• It may take time to display the brightness and color properly right
after displaying the preview screen, switching the camera mode,
changing the camera settings, etc.

• When the battery level is (approximately 10 %) or lower, Camera
cannot be activated.

• You may not be able to use the camera when the battery level is low
or when using the camera in a cold place such as outdoors in
winter.

• If you use the INFOBAR C01 camera in a wrongful manner, you may
be subject to punishment according to laws or ordinances/nuisance
prevention ordinance etc.

• You cannot use VeilView while using the camera.

• You may not be able to use the camera when using other

applications.

Taking Photos

A On the iida Home, Camera.

A confirmation screen asking whether to attach location informations to
data shot appears. Check the content and follow the instructions on
the screen.

《Photo monitor screen》

A Shake reducing icon

On the iida Home, tap Camera [ [Shake Reducing
[ON. After that, the icon is displayed.

B Automatic current location adding icon

On the iida Home, tap Camera [ [Save Settings
[Location info [Automatic added [ON. After that, the icon

is displayed.

C Miniature setting/Blog mode setting key

• On the iida Home, tap Camera [ [Switch camera
[Miniaturize Cam

*

[ [Miniaturize Set to change the

pattern of the blurring. Also, you can change the setting
each time you tap the miniature setting key.

• On the iida Home, tap Camera [ [Blog mode sets
[Blog mode ON/OFF [ON [ [Blog mode sets
[Upload settings to set the upload destination.

* After selec ting Miniaturize Cam, you can edit shot images to make them look like they

are miniatures by blurring some parts of them.

D AF mark

On the iida Home, tap Camera [Tap the focus setting key
[Face AF to detect and focus on a person’s face.

E Zoom bar

Zoom in/out the subject.
Slide your finger to the left/right to display and set the bar.

F Video camera switching key
G Various setting key

Change the various settings.

H Self-timer key

Set the self-timer. Shoot images if the set time has passed
after is tapped.

• The mobile light flashes while counting down.

• Tap ^ to stop a countdown.

I Focus setting key

Set the type of the AF and design of the AF mark.

J Picture size switching key

Set the picture size.

K Scene setting key

Set the scene setting.

L Remaining number of images for shooting
M Brightness adjusting bar

Adjust the brightness.
Slide your finger up/down to display and set the bar.

Multimedia

69

N Previously shot data

Displays the thumbnail of previously shot data. Tap the
thumbnail to confirm the data.

O Shoot

B .

On the iida Home, tap Camera [ [Save Settings [Auto Save
[ON to automatically save the shot image. When the setting is set to

OFF, the photo preview screen is displayed.

• Tap Save to save the shot image.

• Tap Cancel to delete the shot image and return to the photo monitor

screen.
When Blog mode sets is set to ON, Auto Save is set to OFF and the photo
preview screen is displayed.

• Tap Upload to upload the shot image to photo services or SNS on the

Internet, etc.

• Tap Edit to edit the shot image.

• If you operate nothing for approximately three minutes, Camera is

terminated.

• If the mobile light is set to ON, the mobile light is turned on and it is

automatically turned off after approximately three minutes.

• While activating Camera, press 5 to display the operation guide.

Multimedia

AF lock

• By tapping the section on which you want to set the focus in the photo

monitor screen, you can hold it in the state that it focuses on the tapped
section. When the focusing is locked, the AF mark is displayed and focus
lock tone sounds. If the focusing is failed, the AF mark is displayed in red. If
you tap the screen while the focusing is locked, the focusing is unlocked.

• On the iida Home, tap Camera [Tap the focus setting key [Chase Focus

[ON. After that, the AF mark chases the subject even if the subject is

moving.

• On the iida Home, tap Camera [Tap the focus setting key [Infinity Fixed.

After that, you cannot use the AF lock.

• You can take a photo by tapping the AF mark.

Recording Movies

A On the iida Home, Video Camera.

《Movie monitor screen》

A Scene setting key

Set the appropriate scene setting.

B Picture size switching key

Set the picture size.

C Focus setting key

Set the type of the AF.

D Self-timer key

Set the self-timer. Start recording if the set time has passed
after is tapped.

• The mobile light flashes while counting down.

• Tap ^ to stop a countdown.

E Various setting key

Change the various settings.

F Mobile light ON/OFF
G Amount of the time left for recording

70

H Previously recorded data

Displays the thumbnail of previously recorded data. Tap the
thumbnail to confirm the data.

I Record/Stop

J Camera switching key

K Recording time

L Zoom bar

Zoom in/out the subject.
Slide your finger to the left/right to display and set the bar.

M Brightness adjusting bar

Adjust the brightness.
Slide your finger up/down to display and set the bar.

B .

Recording starts.

C .

On the iida Home, tap Video Camera [ [Auto Save [ON to

automatically save the recorded data. When the setting is set to OFF,

the movie preview screen is displayed.

• Tap to play the recorded data.

• Tap Save to save the recorded data.

• Tap Cancel [Yes to delete the recorded data and return to the

movie monitor screen.

• If the battery level becomes (approximately 10 %) or lower while

recording, recording is stopped and saved automatically.

• When you get an incoming call while recording, the recording is stopped

and saved, and then the incoming call screen is displayed. If Auto Save is set
to OFF, the recording is stopped, and then the incoming call screen is
displayed. After the incoming call or the call, the movie preview screen is
displayed.

• If you operate nothing for approximately three minutes, Video Camera is

terminated.

• If the mobile light is set to ON, the mobile light is turned on and it is

automatically turned off after approximately three minutes.

• While activating Video Camera, press 5 to display the operation guide.

Using Photo

In the Photo, you can display the images saved in the microSD
memory card as a list, edit the images, etc.

A On the iida Home, Photo.

The album selection screen is displayed.
Camera is activated by tapping .

B Select an album.

The thumbnail display screen is displayed.
Tap to return to the album selection screen.
Tap to switch the date display and the thumbnail display of the
images.
Slide to the left/right to slide the thumbnails.

C Select an image.

The one image display screen is displayed.
If you tap an image, you can hide/show the informations except for the
image informations.

Multimedia

71

Using Contents Manager

Displaying/Playing Data

You can categorize and list, display/play, check, and manage data on
a microSD memory card, using Contents Manager.

A On the iida Home, Contents Manager.

Multimedia

A Title area

B Contents display area

C Category

《Contents display screen (grid display)》

Displays a selected category name or save location.

Displays a list of the data.

Photo: Displays photos shot by the built-in camera, decorated
pictograms and other images.
Movie: Displays data recorded by the built-in video camera
and other movies.

Music: Displays voice data recorded by the built-in voice
recorder, music and sounds.
TV/SD-Video: Displays recorded data of 1Seg or recorded
data such as data cooperated with recorders.
Doc.: Displays Office and text data.
Others: Displays other data.

D Searching icon

Set the search criteria.

E Thumbnail

Displays thumbnails of the data. If the thumbnail is not
available, displays an icon for data type.

F File name

Displays title name if the data contains title information.
Displays the program name if the data is recorded TV
program.

B Select data.

An application corresponding to the data type is activated and the
data is displayed/played.
Regardless of displaying/playing the data from the contents screen, if
there are multiple applications to display/play, the application
selection screen may be displayed. Select an application to display/
play the data.

• Some data displayed in Contents Manager cannot be displayed/played.

• You cannot play data on which is displayed.

72

Using Menu in the Contents Screen

A On the iida Home, Contents Manager.
B e.
C

Delete
selected
List Players Display types of applications related to file

Switch grid/list Switch grid display and list display of the

Sort Sort saved data.
Slideshow Display the taken pictures by slideshow.
microSD/

phone space
App setting Retrieval condition setting

Delete data.

format.

• If you long-touch a file format, you can
change the application related to the file
format.

contents display area.

Display the space of the microSD memory
card and the INFOBAR C01.

Set the search range under various search
criteria and whether to save the search
criteria.

Initialize settings

Reset the settings to default.

Update Information

Update the information of the microSD
memory card.

Slideshow
settings

Slideshow interval

Set the interval of the slideshow.

Slideshow transition

Set the operation of the slideshow.

Repeat setting

Set whether to repeat the slideshow display.

Shuffle setting

Set whether to display the slideshow in
random order.

Multimedia

73

Cautions for Using 1Seg TV antenna

■ Cautions for Using 1Seg

• No communication charges apply for using 1Seg. However, when
you use an additional service using communication on a data
broadcast etc., packet communication charges apply.

• 1Seg is only for the terrestrial digital TV broadcasting in Japan. You
cannot watch 1Seg overseas due to the differences in the system
and frequency of the broadcasting. Also, you cannot watch BS and
110 degree CS digital broadcasting.

• The INFOBAR C01 may be warm while watching 1Seg. Be careful of
touching for a long time, which may result in a low temperature burn.

• Do not use 1Seg while driving a car, motorcycle and bicycle or
walking. It prevents you from hearing the ambient sounds, and you
are distracted by the video images and sounds. It may cause a
traffic accident.

• Be careful not to watch 1Seg for a long time at a loud volume. It may
harm your hearing.

■ Behavior by Battery Level

If the battery level becomes (approximately 10 %) or lower while
activating 1Seg, it is terminated automatically. If the battery level
becomes so while recording TV programs, the recorded content is

1Seg

saved and 1Seg ends.

The TV antenna is not built in the INFOBAR C01. When you activate
1Seg and set the watching area or when you watch/record 1Seg,
connect the microUSB-3.5φ conversion cable for the TV antenna.
Keep the microUSB-3.5φ conversion cable as straight as possible to
use. And use the INFOBAR C01 in the direction of the good reception
on 1Seg.
Also, Fully charge the battery pack before you watch/record 1Seg
because the microUSB-3.5φ conversion cable and charging devices
cannot be used at the same time.

A Open the external connection jack cover of the

B Connect the microUSB-3.5φ conversion cable to the

INFOBAR C01.

External
connection jack

INFOBAR C01.

Check the
orientation

microUSB-3.5φ conversion cable

74

C After watching, pull out the microUSB-3.5φ

conversion cable from the INFOBAR C01 straight.

D Close the external connection jack cover of the

INFOBAR C01.

• When an earphone is not connected, sounds come out from the speaker
while the microUSB-3.5φ conversion cable is connected.

Initial Setup of 1Seg

Set the watching area when you activate 1Seg for the first time. After
you have finished setting it, you can watch 1Seg.

A On the iida Home, One Seg.

The confirmation screen for the microUSB-3.5φ conversion cable is
displayed. Tap Yes to display the confirmation screen to select whether
to perform the channel settings.

B Yes.

C Select a region.
D Select a prefecture.
E Select a locality.

Searching for local channels begins.

F OK.

• On the iida Home, tap One Seg [One Seg TV [e [Channel setting
[Switch area to change the area.

Watching 1Seg

A On the iida Home, One Seg [One Seg TV.

《1Seg screen》

A Program information

Tap to display the program name.

B Video image

Tap to show/hide the program information and operation key.
Double-tap to switch screen sizes.
Long-touch to display the channel list.
Slide/Flick to the left/right to switch channels.

C Operation key

/ : Switches channels or searches for a channel by

long-touch.

D Subtitle
E Data broadcast

1Seg

75

F 1Seg operation panel/Data broadcast operation panel

/ : Starts/Stops recording.
: Displays the channel list.
: Displays the data broadcast operation panel.
/ : Switches channels or searches for a channel by

long-touch.

: Displays the program guide.
/ : Moves the cursor.
: Selects an item.
: Returns to the previous screen.
: Displays the 1Seg operation panel.

G Signal strength
H Data broadcast lock indicator

Indicates that the data broadcast lock content is displayed on
a data broadcast.

I SSL indicator

Indicates that the page protected by the advanced security is
displayed on a data broadcast.

J Multiple services indicator

Indicates that another service (program) is broadcast in a
channel being received.

K Language

1Seg

• When you activate 1Seg or switch channels, it may take time to get the

video image or data broadcast data due to the characteristics of the digital
broadcasting.

• The video image or sound may be interrupted depending on the signal

strength.

• Camera is not available while activating 1Seg.

■ Operations While Displaying Channel List

• Select the broadcast station name: Switches to the selected
broadcast station.

• Long-touch the broadcast station [Channel overwrite registration
[Yes: Assigns the broadcast station being watched to the selected

remote control number.

• Long-touch the broadcast station [Delete channel [Yes: Deletes
the broadcast station from the selected remote control number.

• Long-touch the unset remote control number: Assigns the broadcast
station being watched to the selected remote control number.

76

Using au Disaster Countermeasure Application

au Disaster Countermeasure is an application in which you can use
Disaster Message Board and Early warning mail (earthquake early
warnings and disaster/evacuation information).

A On the iida Home, (au Disaster

Countermeasure).

The au disaster countermeasure menu is displayed.

《au disaster countermeasure menu》

au災害対策

■ Using Disaster Message Board

Disaster Message Board is a service to enable customers in disaster
areas to register their safety information via IS NET when large-scale
disasters, such as an earthquake whose Japan seismic scale is
approximately 6-lower or more, occur. The registered safety
information can be checked by customers using au phones, and also
from other carriers’ mobile phones, PC, etc.
For details, refer to “Disaster Message Board Service” on au
homepage.

A From the au disaster countermeasure menu,

災害用伝言板

Follow the instructions on the screen for registration/confirmation.

• To register the safety information, an e-mail address (~ezweb.ne.jp) is

required. Set the mail address in advance.

• It is unavailable while connecting via Wi-Fi®.

• The notification mail function of safety information will be provided from the

spring of 2012.

■ Using Early Warning Mail

Early warning mail is a service to collectively deliver earthquake early
warnings and disaster/evacuation information to au phones in the
specified areas.

* From the spring of 2012, we will start providing “Disaster/evacuation information” as early

warning mail. You will be notified on the au homep age for details.

At the time of purchase, receiving setting of early warning mail
(earthquake early warnings and disaster/evacuation information) is set
to (Receive).

受信する

When you receive an earthquake early warning, secure your safety
and act composedly according to the surrounding situations.

(Disaster Message Board).

Applications

77

A From the au disaster countermeasure menu,

受信する

受信しない

受信する

受信しない

緊急速報メール

The inbox is displayed.
Select a mail you want to check to check the details of the mail.

削除 (Delete) Delete received mails.
設定 (Settings) 緊急地震速報 (Earthquake Early Warning) (At

Applications

(Early warning mail).

the top)

Set whether to receive earthquake early
warnings.

• Tap (Receive)/ (Not

receive) [OK.

災害・避難情報 (Disaster/Evacuation
information) (At the top)

Set whether to receive disaster/evacuation
information.

• Tap (Receive)/ (Not

receive) [OK.

音量 (Volume)

Set the volume of the receiving sound for
earthquake early warnings.

バイブ (Vibrator)

Set whether to activate the vibrator when
receiving earthquake early warnings.

マナー時の鳴動 (Linkage to Manner mode)

Set whether to notify you with Manner mode
settings applied while Manner mode is set.

緊急地震速報 (Earthquake Early Warning) (At
the bottom)

Check the operations of the receiving sound
and vibrator.

災害・避難情報 (Disaster/Evacuation
information) (At the bottom)

Check the operations of the receiving sound
and vibrator.

• When you receive an early warning mail, the dedicated alarm tone rings.

The alarm tone cannot be changed.

• Earthquake early warning is to show the areas where a strong shaking

(Japan seismic scale 4 or more) is expected when an earthquake whose
maximum Japan seismic scale is predicted of 5-lower or more has been
detected.

• This service detects an earthquake (P-wave, preliminary tremors) near the

seismic center immediately after the earthquake occurs and automatically
calculates its location, scale and predicted strength of the shaking. After
that, you will be notified of the earthquake as soon as possible within a few
seconds to dozens of seconds before a strong shaking from the earthquake
(S-wave, principal shock) occurs.

• In the vicinity of the seismic center, a strong shaking may reach you before

an earthquake early warning.

• Disaster/Evacuation information is to notify information related to the safety

of citizens, such as evacuation advisories, evacuation orders or various
alarms delivered by the national government or the local governments.

• This service is available only in Japan (Not available overseas).

• Early warning mail is free of both information charges and communication

charges.

• As for this service, au shall not be liable for any damage incurred on the

users resulted from failure or delay of information delivery due to
communication disturbance or system failure, contents of the information or
other problems that are not supposed to be blamed on our company.

• For details on earthquake early warnings provided by the Japan

Meteorological Agency, refer to the Japan Meteorological Agency
homepage.

http://www.jma.go.jp/

• Early warning mails cannot be received while the power is turned off or

during a call.

• Early warning mails may not be received during communication such as

while sending and receiving SMSs (C-mails)/e-mails and while using the
browser or when you are in a place where the signal cannot be received or
the signal is weak, even within the service area.

• Early warning mails which failed to be received will not be able to be

received again.

78

同意

同意する

• The earthquake early warning distribution system provided by this service is

different from that provided by TV, radio and other communication media
and thus the arriving time of earthquake early warnings may be different
among those media.

• Information intended for the areas of other than your present location may

be received.

Using Android Market

You can download and install various applications such as useful
tools or games from Android Market offered by Google.

• Google account is required to use Android Market. For details on
Google account, refer to the “Setting Up a Google Account”.

• For details, on the Android Market screen, tap e [Help to refer
to Android Market Help.

A On the iida Home, Market.

The Android Market screen is displayed.
When you activate Android Market for the first time, the terms of
service are displayed, so tap Accept after confirming the contents.

Using au one Market

You can install Android-based applications recommended by au.

• au one-ID is required to use some functions. For the method of
setting an au one-ID, refer to “Setting au one-ID”.

A On the iida Home, au one Market.

The au one Market screen is displayed.
When you activate au one Market for the first time, the terms of service
and cautions for using au one Market are displayed, so tap
(Agree) [OK after confirming the contents.

• Follow the terms of service to use au one Market. Procedures on

downloading applications and making payment for fee-based applications
differ depending on the distributor of au one Market.

Using GREE Market

You can search for games and contents provided by au one GREE.
You can search them easily without login.

A On the iida Home, GREE_MARKET.

The GREE Market screen is displayed.
You can search for games etc. you want to use from the section on the
screen.

• To use games searched from GREE Market, registering as an au one GREE

member may be required.

Using au Customer Support

au Customer Support

You can check the subscription contents or monthly usage of your au
phone etc. easily and access au customer support site to change the
subscription of your price plan, option services, etc.

• For details, while activating au Customer Support application, tap

e [ (Help) to refer to the help information by au

ヘルプ

Customer Support.

A On the iida Home, au (au Customer

Support).

When you activate for the first time, the setting menu is displayed and
you can perform account setting and automatic updating setting. If you
want to use without setting up an account, tap

set).
Access the au customer support site (https://cs.kddi.com/) to
acquire a new support ID.
If the terms of service are displayed, tap (Agree) after
confirming the contents.

お客さまサポート

(Use without “Support ID”

Applications

79

B

確認する
(Confirm)
変更する
(Change)

サポート&サー

Check the subscription contents or monthly
usage of your au phone etc. easily.
Change the subscription contents of your au
phone.
Refer to “Using Anshin Security Pack”.

ビス (Support
& Service)
ウェブサイト
(Website)

• Tap MENU at the bottom of the screen to display the window for various

inquiries, the setting menu, etc. If MENU is not displayed, tap e.

Confirm the frequently asked questions,
access au customer support site, etc.

Using Anshin Security Pack

You can be supported for the security of the Android phone totally
using three types of applications, “3LM Security”, “Remote Support”
and “VirusBuster Mobile for au”.

• The Anshin Security Pack is a paid service.

Before using location search of Anshin Security Pack

• Note that au shall not be liable for any loss of the users caused by provided

GPS informations.

Precautions

• Even if you are within the service area, you may not be able to obtain the

accurate location information in a location where the signal from GPS
satellites and base stations is weak such as underground mall etc.

• The location information may not be notified if Use GPS satellites is disabled.

To enable it, on the iida Home, tap Settings [Location & security [Check

Applications

Use GPS satellites.

• You can search a terminal whose information of the subscribed au IC-Card

matches that of the au IC-Card which is inserted at the time when you use
the service for the first time.

80

■ 3LM Security

• If the INFOBAR C01 is stolen or lost, you can delete data on the
INFOBAR C01. Contact the Customer Service Center to delete the
data.

• If the INFOBAR C01 is stolen or lost, you can lock the INFOBAR C01
remotely. Also, you can unlock the INFOBAR C01 remotely.

• When activating “3LM Security”, the INFOBAR C01 is locked
remotely, etc., the location information of the INFOBAR C01 will be
sent to the server. Also, you can set the location information to be
always sent.

• The terminal information of INFOBAR C01 is sent to the server
periodically.

■ Remote Support

• When you contact us about the operations of the cell phone, the
operator will share the screen of your INFOBAR C01 with you, and
solve the problems directly by supporting your operations.

■ VirusBuster Mobile for au

• Countermeasure against improper applications: When you install
applications, scan the files and prevent installing improper
applications. Also, you can scan applications already installed
manually and delete the applications.

• WEB filter: Prevent young people from accessing inappropriate sites
such as gambling and dating sites.

• Countermeasure against dangers in WEB: Prevent you from
accessing improper sites such as sites which distribute virus and
improper applications and phishing sites.

• Blocking incoming calls/SMSs: Other than rejecting nuisance calls
and SMSs, you can also reject messages which contain specific
keywords.

※ TRENDMICRO, VirusBuster are trademarks of Trend Mic ro Inc.

Using 3LM Security

リモートサポート

ウイルスバスター

A On the iida Home, au (au Customer

Support) [ (Support &
Services) [ (Anshin Security
Pack) [3LM Security [For Consumer.

Alternatively, on the iida Home, tap 3LM [For Consumer.
When you activate 3LM Security for the first time, the terms of service
for 3LM Security are displayed, so tap I Accept [Activate after
confirming the contents.

サポート & サービス

お客さまサポート

安心セキュリティパック

B Select and set items.

Using Remote Support

A Contact the Customer Service Center.

B On the iida Home, au (au Customer

Support) [ (Support &
Services) [ (Anshin Security
Pack) [ (Remote Support).

Alternatively, on the iida Home, tap (Remote
Support).

C (Agree).

同意する

サポート & サービス

リモ ート サ ポ ート

お客さまサポート

安心セキュリティパック

D Follow the instructions from the operator.

Using VirusBuster Mobile for au

A On the iida Home, au (au Customer

Support) [ (Support &
Services) [ (Anshin Security
Pack) [ for au

(VirusBuster Mobile for au).

Alternatively, on the iida Home, tap (VirusBuster).
When you activate VirusBuster Mobile for au for the first time, the
license agreement for VirusBuster Mobile for au is displayed, so tap

同意する

set up a Google account, a message asking you to set up a Google
account appears. Follow the screen to set up one.

サポート & サービス

ウイルスバスター モバイル

(Agree) after confirming the contents. Also, if you have not

お客さまサポート

安心セキュリティパック

B Select an item.
C Follow the instructions on the screen.

• WEB filter is enabled when you use Android standard browser connected

via IS NET or Wi-Fi®.

Applications

81

Managing Applications

You can delete data, clear cache or stop installed applications
forcefully.

A On the iida Home, Settings [Applications

[Manage applications.

The installed applications list is displayed.

B Select an application.

The detailed application information is displayed.

C Select the operation to perform.

Follow the on-screen instructions to perform it.

• When you select an application installed from Android Market etc., Uninstall

is displayed. Tap it to remove the application.

Applications

82

Checking Your Profile

A On the iida Home, Settings [Profile.

《Profile screen》

■ Using Menu in the Profile Screen

A On the profile screen, e.

B

Edit Edit your profile.
Send by
Infrared
Send by
Bluetooth
Send by IC Send your profile using IC communication.
Attach to Mail Create a mail message using your profile as

Send Setting Set the items to send.

Send your profile using infrared
communication.
Send your profile using Bluetooth®.

an attached data.

• You cannot disable Name and Own phone
number.

• If au IC-Card is not inserted or different au IC-Card is inserted, auIC

Card(UIM) error. Please insert card appears when checking your profile. Tap
OK to display the profile screen. However, information such as Own phone

number or ICCID is not displayed. Also, some operations, such as attaching
the profile to mail, may not be carried out. Insert your au IC-Card and turn
on power again.

Changing the Incoming Ring Tone

You can select and set data for the incoming ring tone.

A On the iida Home, Settings [Sound settings [Melody.
B Select the data.

Changing the Wallpaper

You can select and set an image to display as the wallpaper.

A On the iida Home, Settings [Display settings

[Wallpaper.

B Select the application.
C Select the data [Save/Set wallpaper.

Settings of INFOBAR C01

83

Initializing microSD Memory Card

When initializing a microSD memory card, all data (including
applications) saved on the microSD memory card are deleted.

A

On the iida Home,

[

microSD & phone storage [

Settings

Unmount microSD [OK.

B Erase microSD [Erase microSD [Enter Lock No.

[OK [Erase everything.

• Initialize a microSD memory card while charging or with the battery fully

charged.

• To have the microSD memory card recognized after having unmounted it,

tap Mount microSD.

• Do not unmount the microSD memory card while saving data on it since it

may result in damage to data on the microSD memory card or data loss.

Settings of INFOBAR C01

84

Using Global Passport CDMA/GSM

GLOBAL PASSPORT

Global Passport is the international roaming service which allows the
INFOBAR C01 used in Japan to be available overseas as it is.
You can use the INFOBAR C01 via either GSM network or CDMA
network according to your travel destination.

• You can make a call via GSM network or CDMA network around the
globe with your usual phone number.

• Because International call charges are billed together with call
charges in Japan without any additional application or daily/monthly
call charges, you can pay simply. For details of the countries where
Global Passport GSM/Global Passport CDMA is available, call
charges, the contents of the service, etc., refer to the Global
Passport Owner’s Guide (Japanese) or check them on the au
homepage or at Customer Service Center.

• GSM is an acronym of Global System for Mobile Communications. This is

one of the wireless communication systems applied to digital cell phones
and widely used around the globe such as in Europe, America, Asia,
Oceania and Africa. GSM does not support CDMA, PDC, etc. applied in
Japan.

• The international roaming service is a service which enables voice calls etc.

with your phone or phone number of au used in Japan via cell phones
carrier’s networks overseas.

■ When Using Overseas

When you use Global Passport GSM/Global Passport CDMA
overseas, perform the settings for overseas use.

A You can use the service via au network in Japan.
B Set Area settings of the INFOBAR C01.

C You can make a call via GSM/CDMA network around

the globe with your usual phone number.

D Set Area settings to Japan when you have returned to

Japan.

• If you newly subscribe for the INFOBAR C01, you can use it overseas from

two days after the first use in Japan.

• When you travel overseas, confirm “Phone number for inquiries when

overseas” described on the au homepage and keep a separate memo of it
before traveling. If the INFOBAR C01 or an au IC-Card is stolen or lost,
please contact for inquiries immediately to suspend phone service.

• Those who subscribed exclusively for the prepaid service cannot use

Global Passport GSM/Global Passport CDMA.

• If an au IC-Card is stolen or lost, the card may be inserted into another

mobile phone (including GSM mobile phone for overseas use) by a third
party. So, it is recommended to set the PIN code to protect from improper
use by a third party. For details on the PIN code, refer to “PIN Code”.

Global Function

85

For Overseas Use without Anxiety

The overseas network condition is available on the au homepage.
Make sure to check the condition before leaving Japan.

http://www.au.kddi.com/service/kokusai/tokomae/

■ When the INFOBAR C01 is Stolen or Lost

• If the INFOBAR C01 is stolen or lost while overseas, please contact
Customer Service Center immediately to suspend phone service.
Please be aware that any calling charges and packet
communication charges incurred after theft or loss of a phone are
the responsibility of the customer.

• If the au IC-Card inserted into the INFOBAR C01 is stolen or lost, the
card may be inserted into another mobile phone (including GSM
mobile phone for overseas use) by a third party. So, it is
recommended to set the PIN code to protect from improper use by a
third party.

■ Using the INFOBAR C01 Properly by Knowing

about Calling and Communication Services
Overseas

• Calling charges differ depending on the country/region.

• Discount services do not apply to calling charges incurred while

Global Function

overseas.

• Calling charges are also incurred when receiving calls overseas.

• Depending on the country/region, calling charges may be incurred

from the time that you tap Call.

Configuring the Overseas Settings

■ Obtaining the PRL (Roaming Area Information)

To use the INFOBAR C01 overseas, you are required to change to the
telecommunications carrier’s networks that you connect to at your
travel destination.
The PRL (roaming area information) contains information on roaming
areas of overseas partner providers who have signed an international
roaming contract with KDDI (au).
You need to set the PRL when using the INFOBAR C01 in the CDMA
network areas. Please obtain the latest PRL before traveling.

A On the iida Home, Settings [Wireless & networks

[Mobile networks [Roaming settings [PRL settings
[Update PRL version.

The PRL is obtained. Download the PRL data by following the
on-screen instructions.

• When you download the PRL data, packet communication charges apply.

• Be aware that service may be unavailable in some areas if you do not

update the PRL.

■ Setting the Area

You can set the area where you use the INFOBAR C01.

A On the iida Home, Settings [Wireless & networks

[Mobile networks [Roaming settings [Area settings.

B

Japan Set for using within Japan.
Overseas(Auto) Set (automatically set via CDMA network/

Overseas(CDMA) Set for using CDMA network overseas.
Overseas(GSM) Set for using GSM network overseas.

GSM network) for using overseas.

86

• The country selection screen may be displayed if Area settings is set to other

than Japan. Select the travel country.

■ Setting the Network

You can search and connect to the available networks when the
international roaming begins or a network being used is out of service
area.

A On the iida Home, Settings [Wireless & networks

[Mobile networks [Roaming settings
[Network operators.

The available networks are searched and displayed.

B Select the network to use.

When you tap Search networks, the available networks are searched.
When you tap Select automatically, the optimized network is
automatically set.

• This service is available only while the GSM network is used.

■ Setting the Data Roaming

You can use the packet communication during roaming.

A On the iida Home, Settings [Wireless & networks

[Mobile networks [Data roaming.

Tap OK to enable the data roaming.

• To enable the data roaming, set Area settings to other than Japan in advance.

• If you have not subscribed to IS NET, au.NET charges (525 yen including

tax for the used month) and communi cation charges apply.

Making a Call at Your Travel Destination

■ Making a Call to Another Country (Including Japan)

from Your Travel Destination

You can make a call to Japan or another country from your travel
destination.

Example: To call “212-123-XXXX” in the USA from South Korea

A On the iida Home, Phone.
B Enter “002” as the international access code for

South Korea.

Hold 0 down to enter “+” and the international access code of your
travel destination is automatically added when calling.

C Enter “1” as the country code for the USA.
D Enter “212” as the area code.

If the area code starts with “0”, dial it without including the “0” (There
are some exceptions such as fixed-line phones in some countries or
regions including Italy and Moscow).

E Enter “123XXXX” as the other party’s phone number

[Call.

• If the person you are dialing is using Global Passport, enter the country

code “81” (Japan) regardless of his/her travel destination.

Global Function

87

■ Making a Call within the Same Country While

Overseas

You can call to general fixed-line phones or mobile phones with the
same method as when calling in Japan.

A On the iida Home, Phone.
B Enter a phone number.

When you use GSM network, enter area code + other party’s phone
number.
When you use CDMA network, the method for making calls varies
depending on where you are calling as the following table.

U.S. Mainland, Hawaii, Saipan

New Zealand, South Korea, China, Hong
Kong, Macau, Thailand, Taiwan,
Indonesia, Vietnam, Israel, India,
Bermuda Islands, Bangladesh, Bahamas,
Venezuela
Mexico (Local call)

Global Function

Mexico (Toll call)

Travel destination Number

“1” + Area code +
Other party’s
phone number
Area code + Other
party’s phone
number

Other party’s
phone number
“01” + Area code +
Other party’s
phone number

C Call.

Receiving a Call at Your Travel Destination

You can receive calls with the same method as when receiving calls in
Japan.

• If you receive a call while overseas, the call is forwarded from Japan no

matter where the call is made from. Call charges to Japan are incurred by
the caller and receiving charges by the receiver.

■ Having Calls Made to Your Travel Destination from

Japan

People calling you can use the same method as when calling you from
Japan.

■ Having Calls Made to Your Travel Destination from

Countries Other Than Japan

International access code and “81” (Japan) have to be dialed
regardless of the travel destination since the call is made through
Japan.

Example: To have a call made to your au phone in Japan

“090-1234-XXXX” from the USA

A Enter “011” as the international access code for the

USA.

B Enter “81” as the country code for Japan.
C Omit the first “0” and enter “901234XXXX” as the

phone number of au phone [Call.

88

Troubleshooting

Trouble Detail
Cannot turn on the
power by pressing
f.

The power is turned
off automatically.
The power is turned
off while the wake-up
logo is displayed.
Cannot make calls. • Is the power turned on? (zP. 20)

Cannot receive calls. • Is the INFOBAR C01 within the service area or in a

(out of service
area indicator)
appears.

Display and charging/
incoming indicator
illuminate or flash, but
ring tone does not
sound.

• Is the battery pack charged? (z P.18)

• Is the battery pack attached properly? (zP. 11)

• Is the jack of the battery pack clean?

• Did you hold down f? (z P. 20)

• Is there enough power left in the battery pack?

(zP. 18)

• Is there enough power left in the battery pack?

(zP. 18)

• Is an au IC-Card inserted? (zP. 14)

• Did you enter the correct phone number? (Did you

enter the phone number starting wi th the area
code?) (zP.41)

• Did you tap Call after entering a phone number?

(zP. 41)

• Did you set the correct setting in Area settings?

(zP. 86)

location where the signal is strong? (zP. 31)

• Is the power turned on? (zP. 20)

• Is an au IC-Card inserted? (zP. 14)

• Did you set the correct setting in Area settings?

(zP. 86)

• Is the INFOBAR C01 within the service area or in a

location where the signal is strong? (zP. 31)

• Is your finger etc. off the area around the internal

antenna? (zP. 10)

• Did you set the correct setting in Area settings?

(zP. 86)

• Is the ring tone volume set to other than minimum?

• Is Manner mode disabled? (zP. 44)

Trouble Detail
Cannot charge the
battery pack.

Cannot operate key/
touch panel.
Cannot operate touch
panel as intended.
auIC card(UIM) error. is
displayed.
A message indicating
that charging is
necessary appears.
Calls are answered
automatically.
Battery usage time is
short.

When making a call, a
beeping sound is
heard from the
earpiece and a
connection cannot be
established.
Display is dark. • Is VeilView disabled? (z P.32)

• Are the charging devices connected properly?

(zP. 18)

• Is the battery pack attached properly? (zP.11)

• If you use Fast transfer mode, make sure the USB

driver is installed to the PC.
For the USB driver and install manual, refer to the
Support page in SH DASH (http://k-tai.sharp.co.jp/
support/).

• Is the power turned on? (zP. 20)

• Restart the INFOBAR C01. (zP. 20)

• Check the proper operation of touch panel. (z P. 22)

• Restart the INFOBAR C01. (zP. 20)

• Is an au IC-Card inserted? (zP. 14)

• Is a proper au IC-Card inserted? (zP. 14)

• The battery pack is almost empty. (zP. 18)

• Is Answering memo disabled? (zP.44)

• Is Manner mode disabled? (z P.44)

• Is the battery pack charged enough? (zP. 18)

• Make sure the battery does not approach the end of

its service life.

• Make sure the INFOBAR C01 is not left in the place
for a long period where (out of service area
indicator) appears. (zP. 31)

• Suspend the functions not being used. (zP. 32)

• Are you within the service area or in a location where

the signal is strong? (zP. 31)

• The wireless line is busy or the other party is on
another line. Try again later.

• Make sure the temperature of the INFOBAR C01 is
not high.
When the temperature is high, the backli ght of the
display automatically becomes dark to control heat
generation of the INFOBAR C01.

Appendix/Index

89

Trouble Detail
Cannot hear the other
party.

Cannot use the
microphone of
earphone/
microphone.
Cannot watch 1Seg,
images or sounds are
interrupted or noise
occurs.

Cannot operate the
respective address
book settings.
Images are not
displayed on web
page.
Cannot create a
PC-mail.
Cannot recognize a
microSD memory
card.
Cannot operate the
camera.

Appendix/Index

• Is the earpiece volume set to other than minimum?

(zP. 41)

• Make sure your ear is not covering the earpiece.
Put your ear on the earpiece.

• Is the plug of the connector or earphone properly
connected to the microUSB-3.5φconversion cable?
Insert the connector securely.

• Does the INFOBAR C01 receive an adequate digital
broadcasting signal? (zP. 74)

• Is the microUSB-3.5φconversion cable connected?
(zP. 74)

• Is the selected area for the area where you use the
INFOBAR C01?

• Is the other party’s phone number notified?
If there is no notification, the settings of the address
book are not enabled.

• Make sure the settings is not set to hide images.

• Did you Register a PC-mail account? (zP. 61)

• Is a microSD memory card inserted properly?

(zP. 17)

• Is the microSD memory card mounted? (zP. 84)

• Is there enough power left in the battery pack?

(zP. 18)

• Confirm for using the camera. (zP.67)

For more detailed information, visit auお客さまサポート (au Customer
Support) on the au homepage.

http://www.kddi.com/customer/service/au/trouble/kosho/
index.html

90

Numeric

3LM Security................................. 81

A

Absence Memo............................. 43

Accept all SSL certificates .......... 62

Accessories.................................... 2

Add

Add/Edit Panel............................ 25

Bookmarking a web page .......... 66

widget Home ..............................26

Add/Edit Panel.............................. 24

Address Book

Address Book............................. 46

E-mail messages ........................ 49

SMS (C-mail) messages............. 58

Address group.............................. 49

Advanced Settings....................... 55

Alarm.............................................25

Anshin Security Pack .................. 80

Answer Holding............................ 43

Answering an incoming call........ 43

Answering Memo List .................. 45

Answering memo setting ............ 44

App setting ................................... 73

Application list ............................. 27

Applications.................................. 25

Area settings ................................ 86

Attach to Mail................................ 83

Index

Attaching a hand strap.................12

Attaching the battery pack .......... 11

au Customer Support...................79

au Disaster Countermeasure.......77

au IC-Card .....................................14

au international call service ........42

au one Market ...............................79

au one-ID setting ..........................21

Available menu.............................33

B

Battery pack..................................11

Battery pack cover .......................10

Birthday .........................................46

Bookmark......................................25

Bookmarks....................................65

Browser .........................................65

C

Call.................................................48

Call added special number ..........48

Call/Ans Memo..............................25

Camera

Camera .......................................69

Using...........................................67

Camera lens ..................................10

Cautions for using 1Seg ..............74

Cautions for using the camera.... 67

Cell phone etiquette .......................2

Change.......................................... 80

Change input mode

Hardware keyboard.................... 35

Software keyboard ..................... 39

Character entry screen

Hardware keyboard.................... 34

Software keyboard ..................... 37

Character input (hardware

keyboard) .................................. 34

Character input (software

keyboard) .................................. 36

Charging

Battery pack ............................... 18

Charging with the AC adapter.... 18

Charging with the DC adapter ... 18

Charging indicator ......................... 8

Chat ............................................... 46

Check Settings/Release Settings

.................................................... 56

Compose

Gmail .......................................... 64

PC-mail messages ..................... 63

Confirm ......................................... 80

Contact.......................................... 25

Contents Manager........................ 72

Context menu ............................... 34

Create mail.................................... 48

Create new

E-mail messages ........................ 49

SMS (C-mail) messages............. 57

Create shortcut

Mail address............................... 48

Phone number............................ 48

D

Data roaming ................................87

Delete

Answering Memo List .................45

Early Warning Mail ......................78

Delete email from server.............. 62

Delete selected .............................73

Direct Dial......................................25

Direct Message .............................25

Directions & Navigation............... 25

Disabling sleep mode ..................20

Display.............................................8

Displaying a site from bookmarks

....................................................65

Displaying a site from history ..... 65

Displaying data............................. 72

Domain￥Username .....................62

Double-tap.....................................22

Drag ...............................................23

E

Early warning mail........................77

Earpiece ..........................................8

Edit.................................................83

Edit and call ..................................48

E-mail.............................................49

Emoji

Hardware keyboard ....................35

Software keyboard...................... 39

Energy save ..................................25

Erase microSD..............................84

Event..............................................46

External connection jack ...............9

Appendix/Index

91

External connection jack cover..... 9

F

Facemark

Hardware keyboard ....................35

Software keyboard...................... 39

Family name..................................46

FeliCa mark ...................................10

Flick ...............................................22

For overseas use without anxiety

....................................................86

Forward .........................................64

G

Given name ...................................46

GLOBAL PASSPORT....................85

Global Passport CDMA ................85

Global Passport GSM...................85

Gmail..............................................63

Google account ............................21

GPS................................................46

GREE_MARKET ............................79

Group setting ................................46

Appendix/Index

H

History ...........................................65

Home key.........................................8

I

iida Home ......................................23

Illustrations and descriptions .......3

92

IMAP path prefix........................... 62

IMAP server .................................. 62

Inbox checking frequency........... 62

Incoming History.......................... 43

Incoming indicator......................... 8

Infrared port.................................. 10

Initial setup

Initial setup ................................. 21

Initial setup of 1Seg.................... 75

Input method ................................ 40

Inserting au IC-Card..................... 15

Inserting microSD Memory Card

.................................................... 17

Internal antennas ......................... 10

Internet call................................... 46

Issue One Time Password for PC

Setting ....................................... 56

J

Japan............................................. 86

L

Light sensor ................................... 8

List Players................................... 73

Long-touch ................................... 22

M

Mail................................................ 46

Mail address ................................. 48

Mail check..................................... 51

Making a call to another country

from your travel destination.... 87

Making a call within the same

country while overseas ............88

Manage applications .................... 82

Manage apps.................................26

Manner mode ................................44

Market............................................ 79

Melody ...........................................83

Memo

Add/Edit Panel ............................25

Address Book .............................46

Menu in the contents screen ....... 73

Menu key.........................................8

Menu of the iida Home ................. 24

Menu of the widget Home............ 26

Microphone .....................................8

microSD memory card .................16

microSD memory card slot..........11

microSD/phone space.................. 73

mixi ................................................46

Mobile light ................................... 10

Mouthpiece .....................................8

Moving the panels ........................25

Moving widgets ............................26

Music playlist................................25

N

Names and functions of parts....... 8

Network operators........................87

Nickname ......................................46

Notes on Setting Mail Filter ......... 56

Notification indicator ...................30

Notification/Status panel .............32

Notifications..................................26

Notify me when email arrives. .....62

Number key .....................................8

O

Off...................................................45

On...................................................45

One Seg .........................................25

One Seg TV....................................75

Operating the touch panel ...........22

Option menu..................................33

Organization..................................46

Outgoing History ..........................43

Overseas(Auto).............................86

Overseas(CDMA) ..........................86

Overseas(GSM).............................86

P

Password.......................................62

Paste ..............................................50

PC-mail ..........................................61

Phone.............................................41

Phone number

Address Book..............................46

Phone number.............................48

Photo

Add/Edit Panel ............................25

Photo ...........................................71

PIN code ..........................................4

Pinch ..............................................23

Playing data...................................72

POP3 server ..................................62

Port.................................................62

Postal .............................................46

Power key ....................................... 9

Power off....................................... 20

PRL settings ................................. 86

Profile

E-mail messages ........................ 50

Profile.......................................... 83

Proximity sensor............................ 8

Q

Quick Launch ............................... 24

Quick Search Box ........................ 24

R

Read first....................................... 46

Read last ....................................... 46

Reading e-mail messages ........... 51

Reading SMS (C-mail) messages

....................................................59

Reboot........................................... 20

Receive history

E-mail messages ........................ 50

SMS (C-mail) messages............. 58

Receiver .......................................... 8

Receiving a call at your travel

destination................................. 88

Receiving calls from countries

other than Japan....................... 88

Receiving E-mail messages........ 50

Receiving Gmail ........................... 64

Receiving PC-mail........................ 63

Receiving SMS (C-mail) messages

....................................................58

Reject specified Phone No. ......... 61

Reject unknown senders .............61

Rejection list .................................61

Remote Support............................81

Removing a hand strap................13

Removing au IC-Card................... 15

Removing microSD memory card

....................................................17

Removing the battery pack..........11

Removing widgets........................26

Reply..............................................64

Reply all.........................................64

Require sign-in. ............................62

Return key.......................................8

Ring Set.........................................46

S

Scroll Absorption .........................24

Search............................................26

Security code ..................................4

Security type .................................62

Select language ............................21

Send by Bluetooth........................83

Send by IC.....................................83

Send by Infrared ...........................83

Send email from this account by

default. .......................................62

Send history

E-mail messages.........................50

SMS (C-mail) messages .............58

Send Setting..................................83

Server ............................................62

Set main mail address..................48

Set main phone number...............48

Setting mail filter.......................... 55

Settings

Add/Edit Panel............................ 25

Early warning mail ...................... 78

Simple Settings............................ 55

Sleep mode................................... 20

Slide .............................................. 22

Slideshow ..................................... 73

Slideshow settings ...................... 73

SMS (C-mail)................................. 57

SMS filter ...................................... 61

SMTP server ................................. 62

Sort................................................ 73

Speaker......................................... 10

Speaker off ................................... 45

Speaker on.................................... 45

Status bar ..................................... 30

Status indicator............................ 31

Stop ............................................... 45

Strap eyelet................................... 10

Strap hook .................................... 11

Support & Service........................ 80

Switch grid/list ............................. 73

Switching orientation .................. 33

Switching software keyboards ... 36

Symbol

Hardware keyboard.................... 35

Software keyboard ..................... 39

System Settings

Menu of the iida Home ............... 24

Menu of the widget Home .......... 26

T

Tap................................................. 22

Theme............................................24

Tray................................................ 11

Troubleshooting ...........................89

Turning the power on................... 20

TV antenna ....................................74

Twitter............................................46

U

Unmount microSD........................ 84

Use secure connection (SSL)...... 62

User name .....................................62

V

Video Camera ...............................70

Viewing the address book details

screen ........................................47

Viewing the iida Home .................24

Viewing the iida Home editing

screen ........................................25

VirusBuster Mobile for au............ 81

Volume up/down key......................9

W

Wallpaper

Wallpaper....................................83

widget Home...............................26

Website

Address Book .............................46

au Customer Support..................80

widget Home .................................23

World Clock ..................................25

Appendix/Index

93

January 2012 Edition