Attwood PinPoint GPS User Manual

Increase Speed/

Jog Forward

(from an Anchor Position)

Heading Lock

Steer Left/

Jog Left

(from an Anchor position)

Anchor

1-8

Memory Bank

Prop ON/OFF

Cruise Control

Activates at 1.0 mph

Steer Right/ Jog Right

(from an Anchor Position)

Manual Mode

Exits any mode

Decrease Speed/ Jog Backwards

(from an Anchor Position)

Route Record

Required Calibrations and Settings* To ensure proper operation, it is necessary that the Pinpoint Wireless Remote be synced to the Motor and the Compass and Alignment Calibrations are completed. It is recommended that the calibrations be performed with the motor deployed in a  shing location.

Sync Remote to Motor: press ( ) and ( )

within 10 seconds of applying power

Compass Calibration: press ( ) +

Alignment Calibration: press ( ) +

 Manual /  GPS Features

Audio Mode 1: press ( ) +

Audio Mode 2: press ( ) +

1,1,1

1,1,2

Audio Mode 3: press ( ) +

*Refer to Owner’s Manual for detailed instructions

Route Playback

1,3,1 1,3,2 1,3,3

) buttons to stop recording and to store the Route

1-8

• Press and hold any of the numbered Memory

(

The trolling motor will emit a tune to conﬁ rm that the Route is stored.

To overwrite a stored route, use the same procedure as Storing a

new Route.

)

1-8

RECALLING A STORED ROUTE

• Press the Route Playback ( ) button

) button

1-8

)

1-8

• Press and release the desired numbered Memory (

button

The trolling motor will return you to the nearest point on the recalled

Route then navigate the longest leg of the route.

ROUTE TRAVEL AND COMPLETION

While travelling along a stored route, the direction of travel can be

reversed by recalling the stored route again.

Upon reaching the end of a stored route, the system will enter

Anchor mode

SETTING CRUISE CONTROL

• Press the Cruise Control ( ) button to set the

Cruise Control at 1.0 mph

Cruise Control can be activated while in Heading Lock or Route Playback.

ADJUSTING CRUISE CONTROL SPEED

• Cruise Control ( ) speed can be increased

or decreased in 0.1 mph increments by using the

Increase Speed ( ) button or Decrease

Speed ( ) button

EXITING CRUISE CONTROL

• Press the Cruise Control ( ) button to turn off

Cruise Control

STORING AN ANCHOR POSITION

• Press and hold any of the numbered Memory (

A stored Anchor position can be overwritten with a new Anchor position

by repeating the same procedure.

buttons for two seconds

MANUAL MODE OPERATION

After it is powered up, the trolling motor will operate in

Manual mode by default or if the GPS signal is lost while

operating in a GPS mode. To change from any function to

the Manual mode, press the Manual mode button ( ).

RECALLING A STORED ANCHOR POSITION

• Press and release the desired Memory (

If the desired stored Anchor Position is over a mile away from your

current location, the trolling motor will emit an error tone.

SPEED CONTROL

• To start the propeller, press the Propeller ( )

• To stop the propeller, press the Propeller ( ) button

EXITING ANCHOR POSITION

Increase Speed ( ) button

• To increase motor speed by one level, press the

Manual Mode ( ) button

• Press the Anchor ( ) button or press the

SETTING THE HEADING LOCK

Decrease Speed ( ) button

• To decrease speed by one level, press the

Holding the Increase Speed or Decrease Speed button will cause the

To lock in the trolling motor’s heading and navigate in a

straight line:

speed level to increase to the maximum speed level or decrease to the

minimum speed level.

• Steer the trolling motor in the desired direction

• Press the Heading Lock ( ) button

ADJUSTING HEADING LOCK

• To turn right, press the Steer Right ( ) button

STEERING

• To turn left, press the Steer Left ( ) button

The Heading can be adjusted using the Steer Left and Steer Right buttons.

The speed can be adjusted by using the Increase and Decrease Speed

buttons.

The available steering range allows the trolling motor to turn beyond

180° for operation in reverse

GPS MODE OPERATION

Manual Mode ( ) button

EXITING HEADING LOCK

• Press the Heading Lock ( ) button or the

RECORDING AND STORING A ROUTE

• Press the Route Record ( ) button and begin

navigating along your desired Route

You can use Heading Lock and Manual mode at any time while

recording a Route. Status LED will blink and unit will beep as waypoints

are recorded.

Status LED is solid when the motor has GPS  x.

Status LED blinks slowly when a GPS mode is active.

SETTING THE ANCHOR POSITION

• Press the Anchor ( ) button to lock current

GPS position

ADJUSTING THE ANCHOR POSITION (JOG)

While in Anchor, the Anchor position can be adjusted in

 ve foot increments (Jog), relative to boat orientation, in the

Forward ( ) or Backward ( )

direction selected:

• Press the Left arrow ( ), Right arrow ( ),