AT&T TL76008 User Manual
User’s manual
TL76008
5.8 GHz expansion handset
for use with AT&T model
TL76108
Congratulations
on your purchase
of this AT&T product.
Please read this user’s manual for the information
necessary to install your new AT&T product.
For complete instructions, please refer to the manual
provided with your TL
service or product information, please visit our website
at www.telephones.att.com
or call 1 (800) 222-3111.
In Canada, dial 1 (866) 288-4268.
Model #: TL76008
Type: 5.8 GHz expansion handset
Serial #:
(found on the bottom of the charger)
Purchase date:
Place of purchase:
76108
telephone. For customer
Save your sales receipt and original packaging in case it is necessary
to return your telephone for warranty service.
© 2008 Advanced American Telephones. All rights reserved.
AT&T and the AT&T logo are trademarks of AT&T Intellectual Property II, L.P. d/b/a
AT&T Intellectual Property licensed to Advanced American Telephones.
Printed in China.
Parts checklist
BATTERY PACK
89-1324-00-00
MODEL 102
Save your sales receipt and original packaging in case it is
necessary to ship your telephone for warranty service.
Your telephone package contains the following items.
User’s manual
TL76008
5.8 GHz expansion handset for use
with AT&T model TL76108
User's manual
Battery for cordless
handset
Cordless handset
Battery
compartment
cover
Charger for cordless
handset with power
adapter installed
Belt clip for
cordless handset
User’s manual
TL76008
5.8 GHz expansion handset
for use with AT&T model
TL76108
Table of contents
Getting started
Quick reference guide ...............2
Installation preparation .............4
Charger installation .....................5
Battery installation &
charging ......................................6
Adding & registering
handsets .....................................8
Replacing a handset ................10
Belt clip & optional
headset .................................... 12
Appendix A,
Maintenance .......................... 13
Appendix B, Important
safety information .............. 14
Appendix C, FCC Part 68
and ACTA ................................ 18
Appendix D,
FCC Part 15 ............................21
Appendix E, Limited
warranty ...................................23
Appendix F, Technical
specifications ........................ 27
Appendix G,
Troubleshooting ................... 28
1
Getting started
Quick reference guide
New message
indicator
Flashes when there is
a new message in the
mailbox.
Softkeys
Press to select an item
displayed above the key.
LINE1/FLASH,
LINE2/FLASH
Press LINE1/FLASH
to make or answer a
call on line 1. During a
call, press to receive an
incoming call on line 1 if
call waiting is activated.
Press LINE2/FLASH to
make or answer a call
on line 2. During a call,
press to receive an
incoming call on line 2 if
call waiting is activated.
SPEAKER
Press to turn on the
handset speakerphone.
Press again to resume
normal handset use.
OFF/CLEAR
During a call, press to
hang up.
While using menus, press
to cancel an operation,
back up to the previous
menu, or exit the menu
display.
/X-FER/INTERCOM
Press to begin an
intercom conversation or
to transfer a call.
/VOLUME
Press to adjust listening
volume when on a call.
2
Getting started
Quick reference guide
Feature menu
Caller ID
HANDSET I
MENU CID
RDL
Feature menu
DIRECTORY
MAILBOXES
SETUP HANDSET
REGISTER
Redial
SETUP HANDSET
RINGERS
LOW BATT TONE
KEYPAD TONE
CONTRAST
RENAME
For complete instructions, please refer to the user’s manual. If
you are unable to find your manual, please visit
www.telephones.att.com to read and/or download the
manual.
3
Getting started
Installation preparation
You must install and
charge the battery
before using the
telephone.
Your product may be shipped with a protective sticker covering the
handset display - remove it before use.
For customer service or product information, visit our website at
STOP!
www.telephones.att.com or call 1 (800) 222-3111. In
Canada, dial 1 (866) 288-4268.
Avoid placing the telephone base too close to:
• Communication devices such as: television sets, VCRs, or other
cordless telephones.
• Excessive heat sources.
• Noise sources such as a window with traffic outside, motors,
microwave ovens, refrigerators, or fluorescent lighting.
• Excessive dust sources such as a workshop or garage.
• Excessive moisture.
• Extremely low temperature.
• Mechanical vibration or shock such as on top of the washing
machine or work bench.
See pages 6-7
for easy instructions.
4
Getting started
Charger installation
Plug the power
adapter into an
electrical outlet not
controlled by a wall
switch.
IMPORTANT INFORMATION
Use only the power adapter(s) supplied with this product. To order a
1.
replacement power adapter, visit our website at
www.telephones.att.com, or call 1 (800) 222-3111.
In Canada, dial 1 (866) 288-4268.
The power adapters are intended to be correctly oriented in a vertical
2.
or floor mount position. The prongs are not designed to hold the
plug in place if it is plugged into a ceiling, under-the-table or cabinet
outlet.
5
Getting started
BATTERY PACK
89-1324-00-00
MODEL 102
BATTERY PACK
89-1324-00-00
MODEL 102
Handset battery installation & charging
Install the battery as shown below. After installing the battery,
you can make and receive short calls, but replace the handset
in the telephone base or charger when the handset is not being
used. For optimal performance, charge the handset battery for
at least 16 hours before use. When fully charged, the handset
battery provides up to approximately eight hours of talk time or
four days of standby time.
Press the tab and
slide the battery
compartment
cover downwards.
Insert the supplied
battery as indicated.
Insert the top (on
contacts and tab)
in first, then push
downwards on the
lower portion of the
battery.
6
Step 3Step 2Step 1
Align the cover flat
against the battery
compartment, then
slide it upwards
until it clicks into
place.
Getting started
Handset battery installation & charging
Step 4
Charge the handset by placing it facing the
front in the charger. The CHARGE light will be
on when the handset is charging.
IMPORTANT INFORMATION
Use only the battery supplied with this product. To order a replacement
or spare battery (AT&T model 102, part number 89-1324-00-00) or
equivalent, visit our website at www.telephones.att.com, or
call 1 (800) 222-3111. In Canada, dial 1 (866) 288-4268.
7
Getting started
Adding & registering handsets
Before using a new TL76008 handset, you must register it with
the TL76108 telephone base (purchased separately). The TL76108
telephone can accommodate up to eight cordless handsets.
The handset provided with your TL76108 is automatically
registered as handset 1. Additional handsets will be assigned
numbers in the order they are registered (handset 2, handset
3, and handset 4 etc.). You can register a maximum of eight
handsets.
When first purchased, all optional
NO BASE
SUBSCRIPTION
OK
ENTER BASE ID
################
OK
accessory handsets will show NO BASE
SUBSCRIPTION and ENTER BASE ID on the
screen alternatively. The new handset may
need to be charged for five minutes before
registering to the telephone base.
8
Getting started
Adding & registering handsets
To register a handset to your telephone
base
Make sure the handset battery is installed
and charged properly. You have to enter aYou have to enter a
BASE
RDL MENU CID
MENU softkey
DIRECTORY
MAILBOXES
SETUP BASE
DISPLAY BASE-ID
OK
ENTER BASE ID
################
OK
PLEASE
WAIT!!
T23 PD
15-digit telephone base ID to register the
handset to the telephone base.
To find the telephone base ID and
register the handset:
1. On the telephone base, press the MENU
softkey when in idle mode to enter the
feature menu. Press the or softkey
to scroll to the DISPLAY BASE-ID
then press the OK softkey. The telephone
base ID will be displayed.
2. On the handset, use the keypad buttons
to enter the telephone base ID and press
the OK softkey.
Press the softkey to move the cursor.
–
3.
The handset will first display PLEASE
WAIT!!, then T23 PD followed by
SEARCHING FOR BASE. The screen will
finally display HANDSET X when the
registration is successful.
menu,
SEARCHING
FOR BASE
MENU
NEW
HANDSET X
RDL MENU CID
NOTES:
1. If the registration is not successful, the display
will show NO BASE SUBSCRIPTION. Try the
registration process again.
2. If an incorrect base ID is entered, the base ID
will disappear and ENTER BASE ID will be
displayed.
9
Getting started
Replacing a handset
You may need to de-register your handsets if:
You have eight registered handsets and need to replace a
handset.
-OR-
You wish to change the designated handset numbers of your
registered handsets.
You must first de-register ALL the handsets, and then re-register
each handset you wish to use.
Please read carefully through all the instructions on this page
before beginning the de-registration process.
To de-register all handsets
You can de-register all handsets on the
BASE
MENU CID
RDL
MENU softkey
DIRECTORY
MAILBOXES
SETUP BASE
DISPLAY BASE-ID
KEYPAD TONE
CONTRAST
RENAME
DEREGISTER ALL
OK
SET
DO YOU REALLY
WANT TO
DEREGISTER ALL
HANDSETS?
YES
NO
telephone base only.
1. Press the MENU softkey when in idle
mode to enter the feature menu.
2.
Press the or softkey
SETUP BASE
menu, then press the OK
to scroll to the
softkey.
3. Press the or softkey to scroll to the
DEREGISTER ALL menu, then press the
SET softkey.
4. The screen will display DO YOU REALLY
WANT TO DEREGISTER ALL HANDSETS?.
Press the YES softkey to confirm or press
the NO softkey to return to the previous
screen.
10
Loading...