AT&T TL71208, TL71108, TL72108 User Manual

User’s manual

TL70008

5.8 GHz expansion handset for use with AT&T models TL71108/TL71208/TL71308/ TL72108/TL72208/TL72308/ TL72408/TL78108/TL78208/ TL78308/TL78408

Congratulations

on your purchase

of this AT&T product.

Please read this user’s manual for the information

necessary to install your new AT&T product.

For complete instructions, please refer to the manual

provided with your TL72108/TL72208/TL72308/TL72408/TL78108/

TL78208/TL78308/TL78408

service or product information, please visit our

website at www.telephones.att.com

or call 1 (800) 222-3111.

In Canada, dial 1 (866) 288-4268.

Model #: TL70008 Type: 5.8 GHz expansion handset

Serial #:

(found on the bottom of the charger)

Purchase date: Place of purchase:

TL71108/TL71208/TL71308/

telephone. For customer

Save your sales receipt and original packaging in case it is necessary to return your telephone for warranty service.

© 2008 Advanced American Telephones. All rights reserved. AT&T and the AT&T logo are trademarks of AT&T Intellectual Property II, L.P. d/b/a AT&T Intellectual Property licensed to Advanced American Telephones. Printed in China.

Parts checklist

Save your sales receipt and original packaging in case it is necessary to ship your telephone for warranty service.

Your telephone package includes the following items.

User’s manual

TL70008

5.8 GHz expansion handset for use with AT&T models TL71108/TL71208/TL71308/ TL72108/TL72208/TL72308/ TL72408/TL78108/TL78208/ TL78308/TL78408

User's manual

Battery for cordless handset

Belt clip for cordless handset

Cordless handset

Battery compartment cover

Charger for cordless handset

Power adapter

User’s manual

TL70008

5.8 GHz expansion handset for use with AT&T models TL71108/TL71208/TL71308/ TL72108/TL72208/TL72308/ TL72408/TL78108/TL78208/ TL783080/TL78408

Table of contents

Getting started

Quick reference guide ........... 1

Installation preparation ........ 3

Charger installation ................ 4

Battery installation &

charging ................................. 5

Adding and registering

handsets ...................................... 7

Replacing a handset ............... 9

Belt clip & optional

headset .......................................11

Appendix

Troubleshooting ......................12

Maintenance .............................22

Important safety

information .........................23

FCC Part 68 and ACTA ........27

FCC Part 15...............................30

Limited warranty ....................32

Technical specifications ......36

Getting started

Quick reference guide

CHARGE

On when the handset is charging in the telephone base or charger.

CID

Press to display caller ID information.

PHONE/FLASH

Press to make or answer a call. During a call, press to receive an incoming call if call waiting is activated.

Press or to scroll up or down while in menus. While entering names or numbers, press or to move the cursor to the left or right.

MENU/SELECT

Press to enter the menu. While in the menu, press to select an item or save an entry or setting.

REDIAL/PAUSE

Press to view redial memory. While entering numbers, press and hold to insert a dialing pause.

MUTE/REMOVE

During a call, press to mute microphone. While reviewing the caller ID history, press to delete an individual entry, or press and hold to clear the caller ID history. While predialing, press to delete digits.

SPEAKER

Press to turn on the handset speakerphone. Press again to resume normal handset use.

DIR

Press to display directory entries.

VOLUME

Press on the side of the handset to adjust listening volume. Each press of the button increases or decreases the volume.

OFF/CLEAR

During a call, press to hang up. While using menus, press to cancel an operation, back up to the previous menu, or exit the menu display.

INT

Press to begin an intercom conversation or to transfer a call.

Getting started

Quick reference guide

Feature menu

The > symbol shows a highlighted menu item.

<DIRECTORY

CALL LOG

Feature menu

DIRECTORY CALL LOG RINGER VOLUME RINGER TONE KEY TONE LANGUAGE CLR VOICE MAIL

Using menus

Press or to scroll through menu items. Press MENU/SELECT to select or modify a

highlighted item.

Press OFF/CLEAR to cancel an operation, back up to the previous menu, or exit the menu display.

For complete instructions, please refer to the manual provided with your TL71108/TL71208/TL71308/TL72108/TL72208/ TL72308/TL72408/TL78108/TL78208/TL78308/TL78408 telephone. If you are unable to find your manual, you may visit

www.telephones.att.com to read and/or download the

manual.

Getting started

Installation preparation

You must install and charge the battery before using the telephone.

Your product may be shipped with a protective sticker covering the handset display - remove it before use.

For customer service or product information, visit our website at

STOP!

See pages 5-6

for easy instructions.

www.telephones.att.com or call 1 (800) 222-3111. In

Canada, dial 1 (866) 288-4268.

Avoid placing the telephone base too close to:

• Communication devices such as: television sets, VCRs, or other cordless telephones.

• Excessive heat sources.

• Noise sources such as a window with traffic outside, motors, microwave ovens, refrigerators, or fluorescent lighting.

• Excessive dust sources such as a workshop or garage.

• Excessive moisture.

• Extremely low temperature.

• Mechanical vibration or shock such as on top of the washing machine or work bench.

Getting started

Charger installation

1. Plug the small end

of the smaller power adapter into the jack on the underside of the charger, then route the cord through the slot as shown.

2. Plug the large end

of the smaller power adapter into a power outlet not controlled by a wall switch.

IMPORTANT INFORMATION

Use only the power adapter supplied with this product. To order a

1. replacement power adapter, visit our website at

www.telephones.att.com, or call 1 (800) 222-3111.

In Canada dial 1 (866) 288-4268.

2. The power adapter is intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet.

Getting started

THIS SIDE UP

WARNING:DO NOT BURN OR

PUNCTURE BATTERIES

MADE IN CHINA

Battery Pack

BT5633/BT6823

3.6V 550mAh Ni-MH

THIS SIDE UP

WARNING:DO NOT BURN OR

PUNCTURE BATTERIES

MADE IN CHINA

Battery Pack

BT5633/BT6823

3.6V 550mAh Ni-MH

THIS SIDE UP

WARNING:DO NOT BURN OR

PUNCTURE BATTERIES

MADE IN CHINA

Battery Pack

BT5633/BT6823

3.6V 550mAh Ni-MH

THIS SIDE UP

WARNING:DO NOT BURN OR

PUNCTURE BATTERIES

MADE IN CHINA

Battery Pack

BT5633/BT6823

3.6V 550mAh Ni-MH

Battery installation & charging

Install the battery as shown below. After installing the battery, you can make and receive short calls, but replace the handset in the telephone base or additional charger when not in use. For optimal performance, charge the handset battery for at least 16 hours before use. When fully charged, the handset battery provides approximately five hours of talk time or three days of standby time.

If the battery is depleted, it may take approximately four minutes to charge the handset before it can resume screen display. The screen will continue to display LOW BATTERY until the battery has charged for approximately one hour.

Step 1

Plug the battery securely into the plug inside the handset battery compartment, matching the colorcoded label.

Step 2

Insert the supplied battery with the label THIS SIDE UP facing up as indicated.

Step 3

Align the cover flat against the battery compartment cover, then slide it upwards until it clicks into place.

Getting started

Battery installation & charging

Step 4

Charge the handset by placing the handset face up in the telephone base or in the additional charger. The CHARGE light will be on when charging.

IMPORTANT INFORMATION

Use only the battery supplied with this product. To order a replacement or spare battery (AT&T model 27910, part number 89-0099-00-00) or equivalent, visit our website at www.telephones.att.com, or call 1 (800) 222-3111. In Canada dial 1 (866) 288-4268.

Getting started

Adding and registering handsets

Before using a new TL70008 handset, you must register it with the TL71108/TL71208/TL71308/TL72108/TL72208/TL72308/TL71108/TL71208/TL71308/TL72108/TL72208/TL72308/ TL72408/TL78108/TL78208/TL78308/TL78408 telephone base (purchased separately). The TL71108/TL71208/TL71308/ TL72108/TL72208/TL72308/TL72408/TL78108/TL78208/ TL78308/TL78408 telephone can accommodate up to four cordless handsets.

• The handset provided with the TL71108/TL72108/TL78108 is automatically registered as handset 1. Additional handsets will be assigned numbers in the order they are registered (handset 2, handset 3, or handset 4). You can register a maximum of four handsets.

• The TL71208/TL72208/TL78208 has two handsets automatically registered as handset 1 and 2. You can register two additional handsets, which will be assigned numbers 3 and 4.

• The TL71308/TL72308/TL78308 has three handsets automatically registered as handset 1, 2 and 3. You can register one additional handset, which will be assigned number 4.

• The TL72408/TL78408 has four pre-registered handsets, so you cannot register any additional handsets to it.

Getting started

Adding and registering handsets

To register a handset to your telephone base

NOT REGISTERED

PRESS HNDST LOC

4 SEC ON BASE

PLEASE WAIT...

HANDSET X

REGISTERED

• When first purchased, all optional accessory

handsets show NOT REGISTERED on the screen. The new handset may need to be charged for five minutes before registering to the telephone base.

• Make sure your handset battery is properly installed and charged (pages 5-6).

• Place the unregistered handset into the telephone base. After a few seconds

HNDST LOC 4 SEC ON BASE

the screen.

• Press and hold HANDSET LOCATOR on the main telephone base until the IN USE light comes on (about four seconds), then release the button.

• The handset will show PLEASE WAIT... for a while.

• The handset will show HS X REGISTERED and will beep if the registration was successful.

PRESS

will be shown on

NOTE: If the registration is not successful, the display will show NOT REGISTERED. Reset the handset by lifting the handset out of the telephone base and then place the handset back in the telephone base. Now try the registration process again.

Getting started

Replacing a handset

You may need to de-register your handsets if:

You have the maximum number of registered handsets (four) and need to replace a handset.

-OR-

You wish to change the designated handset number of your registered handsets.

You must first de-register ALL the handsets, and then re-register ALL the handsets you wish to use.

Please read carefully through all the instructions on this page before beginning the de-registration process.

To de-register all handsets

1. Press and hold HANDSET LOCATOR on the telephone base

for about 10 seconds (until the IN USE light turns on and starts to flash), then release the HANDSET LOCATOR button.

2. Immediately press and release HANDSET LOCATOR again. You must press HANDSET LOCATOR while the IN USE light is still flashing. (The light flashes about seven seconds. If the light stops flashing, pick up the handset and place back into the telephone base, then start again step number one.)

3. The handset(s) will show CONNECTING... and it will take about 10 seconds to complete de-registration. ALL handsets will show NOT REGISTERED if de-registration was successful.

NOT REGISTERED

+ 28 hidden pages