Page 1
User Manual (Part 2)
2.4 GHz Expansion
Handset E262
For use with AT&T
model E2562 / E2662B
91-5676-10-00_E262Manual_R0FEB2704.qxd 2/27/2004 12:41 PM Page 1
Page 2
Table of contents
Copyright © 2004 Advanced American Telephones. All Rights Reserved.
AT&T and the Globe Design are trademarks of AT&T Corp.,
licensed to Advanced American Telephones.
STOP!
See pages 2-3
for easy instructions.
You must charge the
battery and register the
handset before use.
For customer service or product
information, visit our web site at
www.telephones.att.com
or call 1-800-222-3111.
Please also read
Important Product Information
Enclosed in product package.
Before you begin........................................1
Parts checklist.............................................1
Battery installation & charging................2
Registering the handset............................3
Belt clip & optional headset ....................4
Quick reference guide..............................5
91-5676-10-00_E262Manual_R0FEB2704.qxd 2/27/2004 12:41 PM Page 2
Page 3
1
Before you begin
This cordless telephone operates with
the maximum power allowed by the
Federal Communications Commission
(FCC). Even so, this handset and
E2562 / E2662B base can communicate
over only a certain distance — which
can vary with the locations of the base
and handset, the weather, and the construction of your home or office.
If you receive a call while you are
out of range, the handset might not
ring — or if it does ring, the call might
not connect when you press L1/L2.
Move closer to the base, then press
L1/L2 to answer the call.
If you move out of range during a
phone conversation, you might hear
noise or interference. To improve
reception, move closer to the base.
If you move out of range without
pressing OFF, your phone will be left
“off the hook.” To hang up properly,
walk back toward the telephone base,
periodically pressing OFF until the call
is disconnected.
Parts checklist
Remember to save your sales receipt and original packaging in case you ever need to
ship your telephone for warranty service. Check to make sure the telephone package
includes the following:
Handset charger
Telephone
handset
Power
adapter
Belt clip
Battery pack
91-5676-10-00_E262Manual_R0FEB2704.qxd 2/27/2004 12:41 PM Page 1
Page 4
2
Light remains on while
battery is charging.
LOW BATTERY
RDL MEMMENU
Battery & charger installation
After installation, place the handset in the charger and allow the battery to charge for 12
hours before use. You can keep the battery charged by returning the handset to the charger
after each use. When battery power is fully depleted, a full recharge takes about 8 hours.
Press coin into slot on
base of handset to
release latch, then
remove cover.
Insert supplied
battery.
Place handset in charger for
12 hours before first use.
Low battery indicator
Return handset to charger when this
symbol flashes. (Handset will beep
when battery is low.)
Insert top
tab first.
Press down to
click in place.
Plug power cord into jack on underside of charger, then plug transformer
into electrical outlet.
Caution: Use only the supplied NiCd battery
(model 2403) or AT&T NiMH replacement battery
(model 2401).
91-5676-10-00_E262Manual_R0FEB2704.qxd 2/27/2004 12:41 PM Page 2
Page 5
3
Registering the handset
Before using your new handset, you must register it with
the E2562 / E2662B base. During registration, you must
enter the 15-digit ID number of the telephone base. To
find this number, go to the base, press MENU, scroll
down to select DISPLAY BASE ID, then press OK.
The handset provided with your telephone is automatically
registered as Handset 1. Additional handsets will be
assigned numbers in the order they are registered (2, 3, 4,
etc.) up to a maximum of eight.
ENTER BASE ID
R
123456789012345
Enter base ID, then press OK.
HANDSET 2
Handset 1 Handset 2 Handset 3
REDIAL MEMMENU
<
OK
91-5676-10-00_E262Manual_R0FEB2704.qxd 2/27/2004 12:41 PM Page 3
Page 6
4
Belt clip & optional headset
Install belt clip as shown below if desired.
For hands-free telephone conversations, you can use any industry standard 2.5 mm
headset (purchased separately). For best results use an AT&T 2.5 mm headset.
Plug 2.5 mm headset
into jack on side of
handset (beneath
small rubber cap).
Snap belt clip into notches on
side of handset. Rotate and pull
to remove.
91-5676-10-00_E262Manual_R0FEB2704.qxd 2/27/2004 12:41 PM Page 4
Page 7
5
Quick reference guide
For complete instructions, please refer to the manual provided with your
E2562 / E2662B telephone.
Off/Clear
During a call, press to hang up.
While using menus, press to cancel an
operation, back up to the previous
menu, or exit the menu display.
Speaker
Press to activate handset speakerphone. Press again to resume normal
handset use (earpiece).
Softkeys
Press a softkey to select a menu item
displayed just above the key.
L1/Flash, L2/Flash
Press L1 to make or answer a call on line 1.
Press L2 to make or answer a call on line 2.
During a call, press to receive an incoming
call, if Call Waiting is activated.
Volume
Press to adjust listening volume.
Xfer/Intercom
Press to transfer a call or initiate an
intercom conversation.
Redial Log
Phonebook
Screen menus
Item 1 Item 2 Item 3
HANDSET 2
RDL MEM
MENU
Menus
Main Menu
Play New MSG
Call History
Mailboxes
Handset Settings
Register
Handset Settings
Ringers
Low Batt Tone
Range Tone
Keypad Tone
Contrast
Enhanced Mode
Rename
91-5676-10-00_E262Manual_R0FEB2704.qxd 2/27/2004 12:41 PM Page 5
Page 8
Copyright © 2004 Advanced American Telephones. All Rights Reserved.
AT&T and the Globe Design are trademarks of AT&T Corp.,
licensed to Advanced American Telephones. Printed in China. Issue 1 AT&T 02/04.
91-5676-10-00
www.telephones.att.com
91-5676-10-00_E262Manual_R0FEB2704.qxd 2/27/2004 12:41 PM Page 6
Loading...