DEFINITY
®
Enterprise Communications Server
Application Notes for Type Approval
Comcode 108343302
Issue 1
June 1999
Copyright 1999, Lucent Technologies
All Rights Reserved
Printed in U.S.A.
Notice
Every effort was made to ensure that the informa tion in thi s book was
complete and accura te at th e time o f prin tin g. Howev er , in format ion is
subject to change.
Your Responsibility for Your System’s Security
Toll fraud is the unauthorized use of your tel ec ommunications system
by an unauthorized party, for example, persons other than your com-
pany’s employees, agents, subcontractors, or persons working on your
company’ s beh alf. Not e t hat t her e ma y be a ris k of toll f rau d ass oci at ed
with your telecommunications system and, if toll fraud occurs, it can
result in substantial additional charges for your telecommunications
services.
You and your system manager are responsible for the security of your
system, such as programming and confi guring your equipment to prevent unauthor ized use. The system manager is also responsible for
reading all installation, instruc tion, and system administration doc uments provided with this pro duct in order to fully understand th e fe atures that can introduce risk of toll fraud and the steps that can be taken
to reduce that risk. Lucent Technologies does not warrant that this
product is immune fro m or will prevent unauthorized use of common-carrier telecommun ic ation services or facili ti es accessed through
or connected to it. Lucent Technologies will not be responsible for any
charges that result from such unauthorized use.
European Union Declaration of Conformity
The “CE” mark affixed to the DEFIN ITY® equipment described in
this book indicates that the e quipment conforms to the foll ow i ng European Union (EU) Directives:
• Electromagnetic Compatibilit y (89 /336/EEC)
• Low Voltage (73/23/EEC)
• Telecommunications T er m inal Equipment (TTE) i-CTR3 BRI
and i-CTR4 PRI
For more information on standards compliance, contact your local distributor.
Comments
To comment on this document, re turn the comment ca rd at the front of
the document.
Acknowledgment
This document was prepared by the Product Documentation Development, Lucent Technologies, Denver, CO.
Lucent Technologies Fraud I n tervention
If you suspect that you are being victimized by toll fraud and you need
technical support or assistan ce , c al l Technical Service Cen ter Toll
Fraud Intervention Hotline at 1 800 643-2353.
Federal Communica tions Commissi on S ta tement
Part 15: Class A Statement. This equipment has been tested and
found to comply with the limits for a Class A digital device, pursua nt
to Part 15 of the FCC Rules. These limits are de sig ne d to provi de reasonable protection against harmful interference when the equipment is
operated in a commercial environme nt. This equipment generates,
uses, and can radiate radio-frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the
user will be required to correct th e in te rfe re nce at his own expense.
Canadian Department of Communications (DOC)
Interference Information
This digital apparatus does not exceed the Class A limits for radio
noise emissions set out in the radio interference regulations of the
Canadian Department of Communications.
Le Présent Appareil Nom
érique n’é
met pas de bruits radioélectriques
dépassant les limites applicables aux appareils numériques de la class
A préscrites dans le reglement sur le brouillage radioélectrique édicté
par le ministére des Communications du Canada.
Trademarks
See the preface of this document.
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Contents
Contents
Contents iii
Application Notes for Type Approval 1
■ Introduction 1
■ General Overview 2
Speech Synthesis Circuit Packs 2
Processing and Environmental CPs 3
Hardware Administration Country Codes 19
Recommended Country Codes 20
■ Country-Specific Configuration and Administration 22
■ Argentina 23
Feature Administration 24
System Parameter Administration 25
Issue 1
June 1999
iii
Trunk Group Administration 30
Digital Trunk Administration 34
■ Australia 37
Country-Specific Features 38
Feature Administration 38
System Parameter Administration 39
■ Belgium & Luxembourg 45
Feature Administration 46
System Parameter Administration 47
■ Bolivia 55
Feature Administration 56
System Administration 57
Trunk Group Administration 62
■ Brazil 68
Country-Specific Feature 69
Feature Administration 69
System Parameter Administration 70
Trunk Group Administration 79
Digital Trunk Administration 84
■ Canada & U.S. 86
■ Chile 88
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Contents
Feature Administration 89
System Parameters Administration 90
Trunk Group Administration 95
DS1 for ISDN trunks to the PPT 100
■ China 101
Country-Specific Feature 102
Feature Administration 102
System Parameters Administration 103
Interactions 115
■ Colombia 117
■ Costa Rica 119
Feature Administration 120
System Parameter Administration 121
Trunk Group Administration 126
■ Czech Republic 134
Issue 1
June 1999
iv
Feature Administration 135
System Parameter Administration 136
■ Ecuador 153
Feature Administration 154
■ France 161
Feature Administration 162
System Parameter Administration 163
Set Options 172
■ Germany 187
Feature Administration 188
System Parameter Administration 189
■ Greece 217
Feature Administration 218
■ Hong Kong 225
Feature Administration 226
System Parameter Administration 227
■ Hungary 233
Country-Specific Feature 234
Feature Administration 234
System Parameter Administration 235
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Contents
Hungarian Private Network Administration 244
■ India 247
Feature Administration 248
System Parameter Administration 249
Trunk Group Administration 256
■ Indonesia 260
■ Israel 262
■ Italy (Lucent Technologies) 264
Country-Specific Feature 265
Feature Administration 265
System Parameter Administration 266
■ Italy-Italtel 280
Feature Administration 281
System Parameter Administration 282
■ Japan 291
Issue 1
June 1999
v
Feature Administration 292
System Parameter Administration 293
2Mbit Trunk (TN2242) 299
Incoming Call Line Identification on Analog Trunks 300
■ Macedonia 303
■ Malaysia 305
Trunk Group Administration 306
■ Mexico 310
Feature Administration 311
System Parameter Administration 312
■ Netherlands 319
Feature Administration 320
ARS/AAR Administration 320
System Parameter Administration 320
■ New Zealand 328
■ Panama 330
Feature Administration 331
Feature-Related System Parameters 332
■ Philippines 343
■ Poland 345
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Contents
Feature Administration 346
System Parameter Administration 347
■ Republic of Korea 355
■ Russia 357
Country-Specific Features 358
Feature Administration 358
System Parameter Administration 360
■ Saudi Arabia 367
Feature Administration 368
System Parameter Administration 369
■ Singapore 375
Feature Administration 376
System Parameter Administration 377
■ Slovak Republic 383
Feature Administration 384
Issue 1
June 1999
vi
System Parameter Administration 385
■ South Africa 402
Feature Administration 403
System Parameter Administration 404
Station Administration 417
■ Spain 419
Country-Specific Features 420
Feature Administration 420
System Parameter Administration 420
■ Sri Lanka 432
■ Switzerland 434
■ Taiwan 436
Feature Administration 437
System Parameter Administration 438
■ Thailand 443
■ Trinidad & Tobago 445
Feature Administration 446
Feature-Related System Parameters 447
■ United Kingdom 458
Feature Administration 459
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Contents
System Parameter Administration 460
■ Venezuela 467
Feature Administration 468
System Parameter Administration 469
■ Vietnam 475
Issue 1
June 1999
vii
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Contents
Issue 1
June 1999
viii
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
Application Notes for Type Approval
Introduction
Issue 1
June 1999
1Introduction
The Application Note for Type Approval contains information concerning the
DEFINITY Enterprise Communications Server (ECS) and how it should be
configured and administered to meet in-country type approval requirements. By
following these guidelines, you can set up a system that allows basic analog and
digital calls on Central Office (CO), Direct Inward Dialing (DID), and Tie trunks
and provides basic interworking with the Public Telephone Network. Also noted
are unique features available when certain country codes are administered.
This book reflects the administration of DEFINITY ECS Release 7 features and all
incremental releases up to and including Release 7.1. It is organized as follows:
■ A general overview presents certain system-wide options (such as tone
plans and country codes)
■ Specific sections outline the administration and configuration items
pertinent to each country
Each country-specific section provides a brief background on key
aspects of that country’s Public Network (PN) such as major analog and
digital standards, availability of PPM, dial-pulse ratios, and so on. Next, it
provides information to help you configure the switch for connection to
in-country analog and digital Public Network Trunks (PNT) and selection of
proper call-progress tones provided by DEFINITY ECS.
To fully implement DE FINITY ECS, refer to the
Administrator’s Guide
for more in-depth information.
DEFINITY ECS
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
General Overview
This section presents certain system-wide options (such as tone plans and
country codes). Throughout the tables in this document, circuit pack apparatus
codes marked with “>” are those preferred and expected to ship with new
systems. They are also the new circuit packs shipped to provide upgrades or
additions to existing systems. Those marked with “#” are planned to be
preferred, but pending Type Approval. The other codes shown have been used
in the recent past and are also acceptable.
Speech Synthesis Circuit Packs
Table 1. Speech Synthesis CP Capabilities
Feature TN725B TN457 TN433
Issue 1
June 1999
2General Overview
Automatic Wakeup Call (in Hotel/Motel
Yes No No
Application)
Auto Circuit Assurance Yes Yes Yes
Leave Word Calling Yes Yes Yes
Visually-Impaired Attendant Service
No Yes Yes
(VIAS )
A-law No Yes Yes
Mu-law Yes Yes Yes
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
Processing and Environmental CPs
Table 2. Cabinet, Power, and Ring Generator Summary
Issue 1
June 1999
3General Overview
Cabinet Type and
Country
Power
U.S. & Canada GAC-MCC
AC-MCC
DC-MCC
AC-SCC
DC-SCC
AC-CSCC
AC-CMC
Argentina GAC-MCC
DC-MCC
AC-SCC
AC-CSCC
AC-CMC
Australia GAC-MCC
DC-MCC
AC-SCC
DC-SCC
AC-CSCC
AC-CMC
Belgium
Luxembourg
GAC-MCC
DC-MCC
AC-SCC
AC-CSCC
AC-CMC
AC Power Voltage
and Frequency
120V/60Hz
Ring
Generator
20Hz
208V/60Hz
240V/60Hz
220V/50Hz 20Hz
240V/50Hz 20Hz 25Hz
220V/50Hz 25Hz
Bolivia GAC-MCC
DC-MCC
AC-SCC
AC-CSCC
AC-CMC
Brazil GAC-MCC
AC-MCC
DC-MCC
AC-SCC
DC-SCC
AC-CSCC
AC-CMC
220V/50Hz 20Hz
127V/60Hz
25Hz
220V/60Hz
Continued on next page
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
Tab le 2. Cabinet, Power, and Ring Generator Summary — Continued
Issue 1
June 1999
4General Overview
Cabinet Type and
Country
Power
Chile GAC-MCC
AC-MCC
DC-MCC
AC-SCC
DC-SCC
AC-CSCC
AC-CMC
China GAC-MCC
DC-MCC
AC-SCC
DC-SCC
AC-CSCC
AC-CMC
Columbia GAC-MCC
DC-MCC
AC-SCC DC-SCC
AC-CSCC
AC-CMC
Costa Rica GAC-MCC
AC-MCC
DC-MCC
AC-SCC
DC-SCC
AC-CSCC
AC-CMC
AC Power Voltage
and Frequency
Ring
Generator
220V/50Hz 20Hz
220V/50Hz 20Hz
120V/50Hz
20Hz
240V/50Hz
120V/60Hz
20Hz
240V/60Hz
Czech Repu blic GAC-MCC
DC-MCC
AC-SCC
AC-CSCC
AC-CMC
Ecuado r GAC-MCC
AC-MCC
DC-MCC
AC-SCC
DC-SCC
AC-CSCC
AC-CMC
220V/50Hz 25Hz
120V/60Hz
20Hz
240V/60Hz
Continued on next page
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
Tab le 2. Cabinet, Power, and Ring Generator Summary — Continued
Issue 1
June 1999
5General Overview
Cabinet Type and
Country
Power
France GAC-MCC
DC-MCC
AC-SCC
AC-CSCC
AC-CMC
Germany GAC-MCC
DC-MCC
AC-SCC
AC-CSCC
AC-CMC
Greece GAC-MCC
DC-MCC
AC-SCC
AC-CSCC
AC-CMC
Hong Kong GAC-MCC
DC-MCC
AC-SCC
DC-SCC
AC-CSCC
AC-CMC
AC Power Voltage
and Frequency
Ring
Generator
220V/50Hz 50Hz
220V/50Hz 25Hz
220V/50Hz 20Hz
200V/50Hz 20Hz
Hungary GAC-MCC
DC-MCC
AC-SCC
AC-CSCC
AC-CMC
India GAC-MCC
DC-MCC
AC-SCC
AC-CSCC
AC-CMC
Indonesia GAC-MCC
DC-MCC
AC-SCC
DC-SCC
AC-CMC
220V/50Hz 20Hz
220V/50Hz 25Hz
220V/50Hz 25Hz
Continued on next page
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
Tab le 2. Cabinet, Power, and Ring Generator Summary — Continued
Issue 1
June 1999
6General Overview
Cabinet Type and
Country
Power
Israel GAC-MCC
DC-MCC
AC-SCC
AC-CSCC
AC-CMC
Italy(Italtel) GAC-MCC
DC-MCC
AC-SCC
AC-CSCC
AC-CMC
Italy(Lucent) GAC-MCC
DC-MCC
AC-SCC
AC-CSCC
AC-CMC
Japan GAC-MCC
AC-MCC
DC-MCC
AC-SCC
DC-SCC
AC-CSCC
AC-CMC
AC Power Voltage
and Frequency
Ring
Generator
230V/50Hz
220V/50Hz 20Hz
220V/50Hz 25Hz
100V/50Hz
20Hz
100V/60Hz
200V/50Hz
200V/60Hz
Macedonia GAC-MCC
AC-MCC
DC-MCC
AC-SCC
DC-SCC
AC-CSCC
Malaysia GAC-MCC
DC-MCC
AC-SCC
DC-SCC
AC-CSCC
AC-CMC
220V/50Hz 20Hz
240V/50Hz 20Hz
Continued on next page
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
Tab le 2. Cabinet, Power, and Ring Generator Summary — Continued
Issue 1
June 1999
7General Overview
Cabinet Type and
Country
Power
Mexico GAC-MCC
AC-MCC
DC-MCC
AC-SCC
DC-SCC
AC-CSCC
AC-CMC
Netherlands GAC-MCC
DC-MCC
AC-SCC
AC-CSCC
AC-CMC
New Zealand GAC-MCC
DC-MCC
AC-SCC
DC-SCC
AC-CSCC
AC-CMC
Panama GAC-MCC
AC-MCC
DC-MCC
AC-SCC
DC-SCC
AC-CSCC
AC-CMC
AC Power Voltage
and Frequency
127V/60Hz
Ring
Generator
20Hz
220V/60Hz
220V/50Hz 25Hz
240V/50Hz 20Hz
120V/60Hz
20Hz
208V/60Hz
240V/60Hz
Philippines GAC-MCC
DC-MCC
AC-SCC
DC-SCC
AC-CMC
Poland GAC-MCC
DC-MCC
AC-SCC
DC-SCC
AC-CMC
220V/50Hz 25Hz
220V/60Hz 20Hz / 25Hz
Continued on next page
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
Tab le 2. Cabinet, Power, and Ring Generator Summary — Continued
Issue 1
June 1999
8General Overview
Cabinet Type and
Country
Republic of
Korea
Power
GAC-MCC
DC-MCC
AC-SCC
DC-SCC
AC-CMC
Russia GAC-MCC
DC-MCC
AC-SCC
DC-SCC
AC-CSCC
AC-CMC
Saudi Arabia GAC-MCC
AC-MCC
DC-MCC
AC-SCC
DC-SCC
AC-CSCC
AC-CMC
Singapore GAC-MCC
DC-MCC
AC-SCC
DC-SCC
AC-CSCC
AC-CMC
AC Power Voltage
and Frequency
110V/60Hz
Ring
Generator
20Hz
220V/60Hz
220V/50Hz 20Hz
110V/60Hz
20Hz
220V/50Hz
230V/50Hz 20Hz
Slovak Republic GAC-MCC
DC-MCC
AC-SCC
DC-SCC
AC-CSCC
AC-CMC
South Africa GAC-MCC
DC-MCC
AC-SCC
DC-SCC
AC-CSCC
AC-CMC
220V/50Hz 25Hz
220-230V/50Hz 25Hz
Continued on next page
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
Tab le 2. Cabinet, Power, and Ring Generator Summary — Continued
Issue 1
June 1999
9General Overview
Cabinet Type and
Country
Power
Spain GAC-MCC
DC-MCC
AC-SCC
AC-CSCC
AC-CMC
Sri Lanka GAC-MCC
DC-MCC
AC-SCC
AC-CSCC
AC-CMC
Switzerland DC-MCC
AC-SCC
AC-CSCC
AC-CMC
Taiwan GAC-MCC
AC-MCC
DC-MCC
AC-SCC
DC-SCC
AC-CSCC
AC-CMC
AC Power Voltage
and Frequency
Ring
Generator
220V/50Hz 25Hz
220V/50Hz 25Hz
220V/50Hz 25Hz
110V/60Hz
20Hz
220V/60Hz
Thailand GAC-MCC
DC-MCC
AC-SCC
DC-SCC
AC-CSCC
AC-CMC
Trinidad &
Tobago
AC-MCC
DC-MCC
AC-SCC
DC-SCC
AC-CSCC
AC-CMC
220V/50Hz 20Hz
120V/60Hz 20Hz
Continued on next page
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
Tab le 2. Cabinet, Power, and Ring Generator Summary — Continued
Issue 1
June 1999
10General Overview
Cabinet Type and
Country
Power
United Kingdom GAC-MCC
DC-MCC
AC-SCC
AC-CSCC
AC-CMC
Venezuela GAC-MCC
AC-MCC
DC-MCC
AC-SCC
DC-SCC
AC-CSCC
AC-CMC
Vietnam GAC-MCC
DC-MCC
AC-SCC
DC-SCC
AC-CSCC
AC-CMC
AC Power Voltage
and Frequency
Ring
Generator
240V/50Hz 25Hz
120V/60Hz
20Hz
240V/60Hz
230V/50Hz 20Hz
Continued on next page
Table 3. Equipment and Software Summary for DC Powered
Multi-Carrier Cabinet (DC-MCC)
Equipment Codes
J58890A Multi-Carrier Cabinet
Equipped With:
J58890CF -48 Volt DC Power Distribution Unit
ED67077 Fan & Filter Assembly
Optionally Equipped With:
J58890AF Expansion Control Carrier
J58890AH Control Carrier
Continued on next page
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
Table 3. Equipment and Software Summary for DC Powered
Multi-Carrier Cabinet (DC-MCC) — Continued
Equipment Codes
J58890AJ Duplicated Control Carrier
J58890AP Control Carrier (Processor) Carrier (G3r)
J58890BB Port Carrier
J58890SA Switch Node Carrier (G3r)
J58890R Enhanced DC Power System Cabinet
Carriers equipped with one 649A Power Supply, except J58890SA which is
equipped with two.
Issue 1
June 1999
11General Overview
Continued on next page
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
Table 4. Equipment and Software Summary for AC Powered Multi-Carrier
Cabinet (AC-MCC)
Equipment Codes
J58890A Multi-Carrier Cabinet
Equipped With:
J58890CE 60Hz 120/208-240 Volt AC Power
Distribution Unit
ED67077 Fan & Filter Assembly
Optionally Equipped With:
J58890AF Expansion Control Carrier
J58890AH Control Carrier
J58890AJ Duplicated Control Carrier
Issue 1
June 1999
12General Overview
J58890AP Control Carrier (Processor) Carrier (G3r)
J58890BB Port Carrier
J58890SA Switch Node Carrier (G3r)
Carriers equipped with 631DA and 631DB power supplies except
J58890SA which is equipped with two 631DA.
Table 5. Equipment and Software Summary for DC Powered Single Carrier
Cabinet (DC-SCC) Stack
Equipment Codes
J58890H Single Carrier Port Cabinet
J58890L Single Carrier Control Cabinet
J58890M Duplicated Single Carrier Control Cabinet
J58890N Expansion Single Carrier Control Cabinet
Equipped With:
676B Power Supply
Optionally Equipped With:
J58890R Enhanced DC Power System Cabinet
J58890CG DC Power Distribution Unit
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
Table 6. Equipment and Software Summary for AC Powered Single Carrier
Cabinet (AC-SCC) Stack
Equipment Codes
J58890H Single Carrier Port Cabinet
J58890L Single Carrier Control Cabinet
J58890M Duplicated Single Carrier Control Cabinet
J58890N Expansion Single Carrier Control Cabinet
Equipped With:
WP-91153 Power Supply
1217A Power Supply
Issue 1
June 1999
13General Overview
Table 7. Equipment and Software Summary for AC Powered Compact Carrier
Cabinet (AC-CSCC)
Equipment Codes
J58890S Compact Single Carrier Cabinet (not
supported in Release 7 and later)
Equipped With:
WP-90510 Power Supply
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
Table 8. Global AC Powered Multi-Carrier Cabinet (GAC-MCC)
Equipment Codes
J58890A Multi-Carrier Cabinet
Equipped With:
J58890CH 50-60Hz 200-240 Volt AC/DC Power
Distribution Unit (AC input with rectifiers to
convert to DC distribution within cabinet)
ED67077 Fan & Filter Assembly
Issue 1
June 1999
14General Overview
Optionally Equipped With
:
J58890AF Expansion Control Carrier
J58890AH Control Carrier
J58890AJ Duplicated Control Carrier
J58890AP Control Carrier (Processor) Carrier (G3r)
J58890BB Port Carrier
J58890SA Switch Node Carrier (G3r)
Carriers equipped with one 649A Power Supply, except J58890SA which is
equipped with two.
Table 9. AC Powered Compact Modular Cabinet (AC-CMC)
Equipment Codes
J58890T Compact Modular Cabinet
Each equipped with 650A power supply.
Table 10. Software Codes
Equipment Codes
J58890 TF Programmed Tapes D EFINITY G3r, R5r,
R6r, R7r
J58890TG Memory Cards DEFINITY G3i, G3si, G3s,
G3csi, G3vs, R6si, R6vs/si, R5vs/si,
R6vs/si/csi, R7csi/si, or MCU
J58890TH Floppy Diskettes DEFINITY G3i, G3si,
G3s, G3csi, G3vs, R5vs/si, R6vs/si/csi,
R77csi/si, or MCU
J58890TN CD-ROM for DEFINITY One
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
Table 11. Control, Network, and Miscellaneous Hardware
Typ e Co de N am e
G3r Control Circuit Packs (G3V1, G3V1.1, G3V2, G3V3, G3V4, R5, R6)
Processor TN1648 System Access - Maintenance
UN330B Duplication Interface
UN331B Processor
TN1650B Memory (32MB)
TN1655 Packet Interface
UN332 Mass Storage System/Network Control
TN1656 Tape Drive
TN1657 Disk Drive
AHF111 Processor Expansion Bus Terminator
Issue 1
June 1999
15General Overview
CFY1B Current Limiter
Switch Node TN572 Switch Node Clock
TN573 Switc h Node Interface
AHF105 Switch Node Bus Terminator
G3vs, G3s, G3si & G3i Control Circuit Packs (G3V1.1, G3V2, G3V3, G3V4)
Processor TN786B Processor
CPP1 Memory (Expansion)
TN772 Du plication Interface
TN777B Network Control
T N778 Packet Control
TN765 Processor Interface
TN756 Tone Detector/Generator
982LS Current Limiter
R5vs, R5si-8MB & R5si-12MB, R6vs/si-16MB Control Circuit Packs
Processor TN790 Processor
TN772 Du plication Interface
TN777B Network Control
T N778 Packet Control
Continued on next page
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
Table 11. Control, Network, and Miscellaneous Hardware — Continued
Typ e Co de N am e
TN765 Processor Interface
982LS Current Limiter
R6csi Control Circuit Pack
Processor TN798 Processor
R7si Control Circuit Pack
Processor TN798 Processor
TN792 Du plication Interface
TN794 Network Control/Packet Interface
TN765 Processor Interface (only required if
system has BX.25 interfaces)
982LS Current Limiter
Issue 1
June 1999
16General Overview
R7csi Control Circuit Pack
Processor TN798 Processor
Other Circuit Packs and Circuit Modules
Power 631DA MCC AC Power Unit (+5V)
631DB MCC AC Power Unit (-48/-5V)
644A MCC DC Power Unit (+5V)
645B MCC DC Power Unit (-48/-5V)
649A MCC DC Power Unit (-48/-5/+5V)
650A CMC AC Power Unit (-48/-5/+5/+12V)
20, 25, 50Hz Ringer/Neon
WP-90510 L4 CSCC AC Power Unit (+5/-5/-48V)
20Hz Ringer
WP-90510 L5-25 CSCC AC Power Unit (+5/-5/-48V)
25Hz Ringer
WP-90510 L6-20 CSCC AC Power Unit (+5/-5/-48V)
20Hz Ringer
WP-91153 L3 SCC AC Power Unit (+5/-5/-48V) 20Hz
Ringer
WP-91153 L4-25 SCC AC Power Unit (+5/-5/-48V) 25Hz
Ringer
Continued on next page
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
Table 11. Control, Network, and Miscellaneous Hardware — Continued
Typ e Co de N am e
1217A Global SCC AC Power Unit
676B SCC DC Power Unit (+5/-5/-48V)
TN755B Neon Power
System/Network TN766 Expansion Interface
TN570B Expansion Interface
TN574 DS1 Converter
TN1654 DS1 Converter (T1/E1)
TN755B Maintenance (EPN)
TN771D Maintenance/Test
TN2202 50Hz Ring Generator (F rance)
TN2305 ATM Interface, Multi Mode
Issue 1
June 1999
17General Overview
TN2306 ATM Interface, Single Mode
TN799 Control LAN
Other 105B Isolation Data Interface (IDI)
116A Isolation Data Interface (IDI)
120A Integrated Channel Service Unit
(ICSU) (T1 only)
122A Music-On-Hold Interface
124D1 MCC 20Hz Ring Generator
130A1 MCC 25Hz Ring Generator
700A DS1 Loopback Jack (T1 only)
808A Emergency Transfer Panel
888B DS1 75 Ohm Coax Adapter
9823A Lightwave Transceiver (multi-mode
shortwave)
9823B Lightwave Transceiver (multi-mode
longwave)
300A Fiber Transceiver (single mode)
AHF110 SCC TDM/LAN Bus Terminator
Continued on next page
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
Table 11. Control, Network, and Miscellaneous Hardware — Continued
Typ e Co de N am e
CFY1B Current Limiter
ZAHF4 MCC TDM/LAN Bus Terminator
TN556B ED1E-546 DEFINITY AUDIX (386 MFB)
TN567 ED1E-546 DEFINITY AUDIX (486 MFB)
TN801 J58890MA LAN Gateway R2
TN2169 ED1E-546 DEFINITY AUDIX Alarm
Interface
TN2170 ED1E-546 Ethernet/Alarm Interface
TN2208 ED1E-546 LAN Gateway R1 (486 MFB)
TN802 J58890MA-1, List 10, Internet Protocol
Trunk
Issue 1
June 1999
18General Overview
Continued on next page
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
Hardware Administration Country Codes
DEFINITY ECS supports administration of circuit pack operating parameters
through the selection of country codes listed in
to a pre-defined set of (one or more) programmable hardware or firmware
attributes.
Table 12. Country Code Assignments
Administered
Code Country
1 U.S. & Canada
2 Australia
3Japan
4Italy
5 Netherlands
Table 12
Issue 1
June 1999
19General Overview
. Each code corre spon d s
6 Singapore
7Mexico
8 Belgium & Luxembourg
9Saudi Arabia
10 United Kingdom
11 Spain
12 France
13 Germany & South Africa
14 Czech Republic & Slovak Republic
15 Russia
16 Argentina
17 Greece
18 China
19 Hong Kong
20 Thailand
21 Macedonia
22 Poland
23 Brazil (Or, continue to use country code 16)
24 Nordic (Norway, Sweden, Iceland, Denmark)
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
Recommended Country Codes
Table 13 provides a summary of recommended Country Codes. If a Country Code
value is not assigned to a particular country, (for example, no Country Code has
been assigned to Venezuela), review
Also, set the Tone Detector Pr ecision and Tone Detector Mode according to
13.
Table 13. Recommended Country Codes
T able 13
to determine the appropriate code.
Issue 1
June 1999
20General Overview
Table
Country
To ne
Gen ISDN
Digital
XMIT
Trunk
Group
Country**
Analog
Ring
Cadence
Ton e D et .
Precision
U.S. & Canada 1 1 1 1 1 Precise 1
Argentina &
16 16 16 16*** 16 Broadband 1
Brazil
Australia 2 2 2 2 2 Precise 2
Belgium &
8* 8 5 8 8 Medium 5
Luxembourg
China 18 18 18 18 18 Medium 4
Chile 1 12a 1 1 1 Precise 6
Costa Rica 1 12a 1 1 1 Precise 6
Czech
14* 14 14 14 14 Medium 4
Republic &
Slovak
Republic
France 12 12 12 12 12 Precise 4
Germany &
13* 13^ 13 13 13 Medium 4
South Africa
Ton e
Det.
Mode
Greece 17 17 17 17 17 Broadband 1
Hong Kong 19 19 19 19 19 Precise 1
Hungary - 1 1 Medium 1
Italy 4 4 4 4 4 Precise 1
Japan 3 3 3 3 3 Precise 1
Maced onia 21 21 21 21 21 Medium 4
Mexico 7* 7 7 7 7 Precise 1
Netherlands 5* 5 5 5 5 Medium 5
Continued on next page
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
Tab le 13 . Recommended Country Codes — Continued
Issue 1
June 1999
21General Overview
Country
To ne
Gen ISDN
Digital
XMIT
Trunk
Group
Country**
Analog
Ring
Cadence
Ton e D et .
Precision
Nordic
New Zealand 2 ETSI 2 2 2 Precise 2
Poland 22 22 22 22 22 Medium 1
Russia 15 15 15 15 15 Medium 4
Saudi Arabia 9 9 9 9 9 Precise 1
Singapore 6* 6 6 6 6 Precise 1
Spain 11* 11 11 11 11 Precise 4
Taiwan 1 3 1 1 1 Precise 1
Thailand 20 20 20 20 20 Medium 4
UK OTR001 10 10 10B 10 - Precise 3
UK
10 10 10A 10 - Precise 3
Non-OTR001
Venezuela 1 - - - 5 P recise 1
Continued on next page
Ton e
Det.
Mode
* Needs additional customized tone administration to meet country requirements.
(This administrative detail is covered in country-specific sections.)
** These country codes select the appropriate FW protocols on the various analog
CO/DID trunks. These value s also nee d to be duplicated on the DS1 Administration.
“Country Protocol” field for the appropriate FW protocol to be selected on the
TN464x.
*** To enable Block Collect Call in Brazil, use Country Code 23.
- Feature is not provided in this country or hardware d oes not support administrable
selection. Accep t the default in these cases.
^ Protocol version selection of “a” corresponds to 1TR6 (Germany Specific) and “b”
corresponds to E-DSS 1 (E ur o ISDN). Protocol version selection depends on the type
of public network service purchased.
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
Issue 1
June 1999
22Country-Specific Configura tion and Administration
Table 14 provides expanded information for the Tone Det. Mode field in
Table 14. Available Tone Detection Modes
Code Mode
1Italy
2 Australia
3 United Kingdom
4 Standard Wideband
(345 - 625Hz, - 55dB)
5 Broad Wideband
(300 - 1190Hz, - 35dB)
6USA
Table 13
.
Country-Specific Configuration and Administration
The following sections present information on how to administer DEFINITY ECS
for each of the supported countries. Values shown should actually be entered
into fields on the specified screens.
NOTE:
In the tables that follow for each country , circuit pack (CP) apparatus codes
marked with “>” are those preferred and expected to ship with new
systems. They are also the new CPs shipped to provide upgrades or
additions to existing systems. Those marked with “#” are planned to be
preferred, but pending Type Approval. The other codes shown have been
used in the recent past and are also acceptable.
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
Argentina
Table 15 shows the recommended circuit packs.
Table 15. Recommended and Available CPs in Argentina
Equipment Equipment Type
Cabinet Type & Power GAC-MCC DC-MCC AC-SCC AC-CSCC
AC-CMC
AC Power Voltage & Freq 220V/50Hz
Ring Generator 20Hz
Tone Detector >TN2182B >TN744D TN748D TN748C
Tone Clock >TN2182B TN780
R2MFC Circuit >TN744D TN744B
Speech Synthesizer >TN725B
Issue 1
June 1999
23Argentina
Call Classifier >TN744D
Announcement TN750C TN750B
Analog DID Trunk n/a
Analog CO Trunk (No PPM) >TN747B
Analog CO Trunk (w/PPM) n/a
4 Wire Tie Trunk >TN760Dv15
2 Wire Tie Trunk n/a
Auxiliary Trunk >TN763D
Digital CO/DID Trunk >TN464F TN464E TN464D
Digital Tie Trunk >TN464F TN464E TN464D
Digital PRI CO Trunk >TN464F TN464E TN464D
Digital BRI Trunk
Digital Converter PRI-DASS
Digital Converter PRI-DPNSS
Digital Converter PRI-BRI
8 Port Analog Line TN742
16 Port Analog Line >TN746B
4 Wire Digital Line >TN754B
Continued on next page
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
Tab le 15 . Recommended and Available CPs in Argentina — Continued
Equipment Equipment Type
2 Wire Digital Line #TN2224 >TN2181
Data Line >TN726B
BRI-U Line
BRI-ST Line
NOTE:
A-law companding is the national standard in Argentina. However,
Mu-law is used internally to the system for service circuits and
analog lines. Network interfaces are configured as A-law if required.
NOTE:
TN760Dv15 currently is not available from Manufacturing. If needed,
contact the ITAC.
Issue 1
June 1999
24Argentina
Continued on next page
Feature Administration
The screen displays shown in this section were effective the date the type
approval was awarded. The screens may have changed since that date.
Only those feature-related parameters that may have a Type Approval or basic
connectivity implication for a particular country are listed here.
■ ARS/AAR Administration
To enable ARS administration, on the System-Parameters
Customer-Options screen, set the
ARS/AAR defaults. All default ARS analysis codes are deleted before
dialed strings are added for routing when DEFINITY is installed outside of
North America. Be aware that the default for the 10 digits cause dialing
problems. In particular, the following call types (appear as ARS/AAR
defaults) typically are not used in non-North American ARS/AAR tables:
fnpa: North American numbers with an area code.
hnpa: North American numbers without an area code.
svc: North American numbers of the screen ‘‘x11’’.
ARS
field to y. You also should check all
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
Lucent recommends only the following call types be used outside North
America:
int: For all international numbers.
natl: For all national PN numbers.
pubu: For all other external (that is, not extensions)
numbers.
System Parameter Administration
Feature-Related System Parameters
Page 1 of 6
FEATURE-RELATED SYSTEM PARAMETERS
Issue 1
June 1999
25Argentina
Trunk-to-Trunk Transfer: all
Coverage - Subsequent Redirection No Answer Interval: 2
Coverage - Caller Response Interval (seconds): 4
Keep Held SBA at Coverage Point? y
Automatic Callback - No Answer Timeout Interval (rings): 3
Call Park Timeout Interval (minutes): 10
Off-Premises Tone Detect Timeout Interval (seconds): 20
AAR/ARS Dial Tone Required? y
Music/Tone on Hold: none
Music (or Silence) on Transferred Trunk Calls? no
DID/Tie/ISDN Intercept Treatment: attd
Internal Automatic Answer for Attendant Extended Calls? n
Automatic Circuit Assurance (ACA) Enabled? n
Page 2 of 6
FEATURE-RELATED SYSTEM PARAMETERS
LEAVE WORD CALLING PARAMETERS
Maximum Number of Messages Per Station (when MSA not in service):10
Stations with System-wide Retrieval Permission (enter extension)
1: 2: 3: 4: 5:
6: 7: 8: 9: 10:
WARNING! SEE USER DOCUMENTATION BEFORE CHANGING TTI STATE
Terminal Translation Initialization (TTI) Enabled? n
External Coverage Treatment for Transferred Incoming Calls? n
SECURITY VIOLATION NOTIFICATION (SVN) PARAMETERS HAVE MOVED TO
THE SYSTEM-PARAMETERS SECURITY SCREEN
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
Page 3 of 6
FEATURE-RELATED SYSTEM PARAMETERS
Reserved Slots for Attendant Priority Queue: 5
Time before Off-hook Alert: 10
Emergency Access Redirection Extension:
Service Observing Warning Tone? y
Number of Emergency Calls Allowed in Attendant Queue: 5
Call Pickup Alerting? n
Deluxe Paging and Call Park Timeout to Originator? n
Controlled Outward Restriction Intercept Treatment: tone
Controlled Termination Restriction (Do Not Disturb): tone
Controlled Station to Station Restriction: tone
AUTHORIZATION CODE PARAMETERS Authorization Codes Enabled?
Authorization Code Length:
Authorization Code Cancellation Symbol: #
Attendant Time Out Flag? n
Display Authorization Code? y
Issue 1
June 1999
26Argentina
Page 4 of 6
FEATURE-RELATED SYSTEM PARAMETERS
SYSTEM PRINTER PARAMETERS
System Printer Extension: Lines Per Page: 60
SYSTEM-WIDE PARAMETERS
Switch Name:
CALL CENTER SYSTEM PARAMETERS
Direct Agent Announcement Extension:
Direct Agent Announcement Delay:
Converse Delay Data1: 0 Data2: 2
Direct Agent Announcement Extension: Converse Pulse ON: 100 OFF: 70
Prompting Timeout (secs): 10
CALL MANAGEMENT SYSTEM PARAMETERS
BCMS/VuStats Measurement Interval: hour
BCMS/VuStats Abandon Call Timer (seconds): Validate Login IDs? n
ACD Login Identification Length: Adjunct CMS Release:
MALICIOUS CALL TRACE PARAMETERS
Apply MCT Warning Tone? n MCT Voice Recorder Trunk Group:
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
Page 5 of 6
FEATURE-RELATED SYSTEM PARAMETERS
Public Network Trunks on Conference Call: 5 Auto Start? n
Conference Parties with Public Network Trunks: 6 Auto Hold? n
Conference Parties without Public Network Trunks: 6 Attendant Tone? y
Night Service Disconnect Timer (seconds): 180 Bridging Tone? n
Short Interdigit Timer (seconds): 3 Conference Tone? n
Unanswered DID Call Timer (seconds): Intrusion Tone? n
Line Intercept Tone Timer (seconds): 30
DID Busy Treatment: tone
Allow AAR/ARS Access from DID/DIOD? n
DISTINCTIVE AUDIBLE ALERTING
Internal: 1 External: 2 Priority: 3
Attendant Originated Calls: external
Page 6 of 6
FEATURE-RELATED SYSTEM PARAMETERS
Issue 1
June 1999
27Argentina
Pull Transfer: n Update Transferred Ring Pattern? n
Outpulse Without Tone? y Wait Answer Supervision Timer? n
Repetitive Call Waiting Tone? n
Allow Conference via Flash? y
Vector Disconnect Timer (min): Network Feedback During Tone Detection? y
Hear Zip Tone Following VOA? n
Intercept Treatment On Failed Trunk Transfers? n
Station Tone Forward Disconnect: silence
Level Of Tone Detection: precise
RECALL TIMING
Flashhook Interval? y Upper Bound (msec): 1000
Lower Bound (msec): 200
ENHANCED DCS
Enhanced DCS Enabled? n
Apply Intercept Locally? y Enforce PNT-to-PNT Restrictions? n
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
System Parameter Country-Options
Administration
Page 1 of 7
SYSTEM PARAMETERS COUNTRY-OPTIONS
Companding Mode: Mu-Law Base Tone Generator Set: 1
440Hz PBX-dial Tone? n 440Hz Secondary-dial Tone? y
Digital Loss Plan: 1
Analog Ringing Cadence: 1
TONE DETECTION PARAMETERS
Tone Detection Mode: 6
Interdigit Pause: short
NOTE:
Companding Mode: A-law is the national standard. Mu-law is used internal to the
system for service circuits and analog lines. Network interfaces are configured as
A-law if req ui red.
Issue 1
June 1999
28Argentina
■ Customized Individual Tones — In this section, customized tone
definitions follow the data-entry syntax as specified for entry on the
Individual Tone Administration Screen:
[(Frequency/Level)|silence|goto)][(Duration ms)|(Step)]
— Reorder (Congestion):
1. (425/-11)(250)
2. (silence)(250)
3. (goto)(1)
— CO Dial Tone:
1. (350+440/-13.75)(1000)
2. (goto)(1)
—PBX Dial Tone:
1. (425/-11)(1000)
2. (goto)(1)
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
June 1999
Application Notes for Type Approval
Multifrequency-Signaling-Related System
Parameters
Page 1 of 3
MULTIFREQUENCY-SIGNALING-RELATED SYSTEM PARAMETERS
Incoming Call Type: group-ii-mfc
Outgoing Call Type: group-ii-mfc
Maintenance Call Type: none
Test Call Extension:
Interdigit Timer (sec): 10
Outgoing Forward Signal Present Timer (sec): 15
Outgoing Forward Signal Absent Timer (sec): 30
Multifrequency Signaling Incoming Intercept Treatment? y
Received Signal Gain(-Loss) (dB): 0
Transmitted Signal Gain(-Loss) (dB): -3
ANI Prefix:
ANI for PBX:
Next ANI Digit: send-ani
ANI Prefix: Collect All Digits Before Seizure? n
Request Incoming ANI (non-AAR/ARS)? n
Called Party Category: user-type
Use COR for Calling Party Category? n
Issue 1
29Argentina
Page 2 of 3
MULTIFREQUENCY-SIGNALING-RELATED SYSTEM PARAMETERS
INCOMING FORWARD SIGNAL TYPES INCOMING BACKWARD SIGNAL TYPES
(Tones from CO) (Tones to CO)
Group-I Group-II Group-A Group-B
11: ignored 1: normal 1: next-digit 2: intercept
12: ignored 2: normal 3: end-of-dial 3: busy
13: ignored 3: normal 4: congestion 4: congestion
14: ignored 4: normal 6: free
15: ignored 5: normal
6: normal
7: normal
8: normal
9: normal
10: normal
11: normal
12: normal
13: normal
14: normal
15: normal
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
June 1999
Application Notes for Type Approval
Page 3 of 3
MULTIFREQUENCY-SIGNALING-RELATED SYSTEM PARAMETERS
OUTGOING FORWARD SIGNAL TYPES OUTGOING BACKWARD SIGNAL TYPES
(Tones to CO) (Tones from CO)
Group-I Group-II Group-A Group-B
12: ani-not-avail 2: normal 1: next-digit 1: congestion
15: end-of-ani 1: attendant 2: last-2-digits 2: intercept
6: data-call 3: end-of-dial 3: busy
4: congestion 4: congestion
5: send-ani 5: intercept
6: setup-sppath 6: free
7: last-3-digits 7: free
8: congestion 8: busy
9: last-digit 9: congestion
10: restart 10: congestion
11: congestion 11: congestion
12: congestion 12: congestion
13: congestion 13: congestion
14: congestion 14: congestion
15: congestion 15: congestion
Issue 1
30Argentina
Trunk Group Administration
CO Trunk Group Administration
Page 1 of 10
TRUNK GROUP
Group Number: Group Type: co CDR Reports: y
Group Name: OUTSIDE CALL COR: 1 TN: 1 TAC:
Direction: two-way Outgoing Display? n
Dial Access? n Busy Threshold: 99 Night Service:
Queue Length: 0 Country: 1 Incoming Destination:
Comm Type: voice Auth Code? n Digit Absorption List:
Prefix-1? n Trunk Flash? n Toll Restricted? n
TRUNK PARAMETERS
Trunk Type: loop-start
Outgoing Dial Type: tone Cut-Through? n
Trunk Termination: rc Disconnect Timing(msec): 500
Auto Guard? n Call Still Held? n Sig Bit Inversion: none
Terminal Balanced? n RA Trunk Loss: 0db
Trunk Gain: high
Disconnect Supervision - In? n Out? n Cyclical Hunt? n
Answer Supervision Timeout: 10 Receive Answer Supervision? n
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
June 1999
Application Notes for Type Approval
Page 2 of 10
TRUNK FEATURES
ACA Assignment? n Measured: none
Maintenance Tests? y
Data Restriction? n
Abandoned Call Search? n
Suppress # Outpulsing? n
Page 3 of 10
TRUNK GROUP
ADMINISTRABLE TIMERS
Incoming Disconnect(msec): 500 Outgoing Disconnect(msec): 500
Outgoing Dial Guard(msec): 1600
Incoming Glare Guard(msec): 1500 Outgoing Glare Guard(msec): 1500
Ringing Monitor(msec): 5200 Incoming Seizure(msec): 500
Outgoing End of Dial(sec): 10 Outgoing Seizure Response(sec): 5
Programmed Dial Pause(msec): 1500
Flash Length(msec): 540
Issue 1
31Argentina
END TO END SIGNALING
Tone(msec): 350 Pause(msec): 150
OUTPULSING INFORMATION
PPS: 10 Make(msec): 40 Break(msec): 60 PPM? n
Page 4 of 10
TRUNK GROUP
Administered Members (min/max): 0/0
Total Administered Members: 0
GROUP MEMBER ASSIGNMENTS
Port Code Sfx Name Night Mode Type Ans Delay
1:
2:
3:
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
June 1999
Application Notes for Type Approval
DIOD Trunk Group Administration
Page 1 of 10
TRUNK GROUP
Group Number: Group Type: diod CDR Reports: y
Group Name: OUTSIDE CALL COR: 1 TN: 1 TAC:
Direction: two-way Outgoing Display? n
Dial Access? n Busy Threshold: 99
Queue Length: 0 Country: 7
Auth Code? n Digit Absorption List:
Prefix-1? n Trunk Flash? n Toll Restricted? n
TRUNK PARAMETERS
Trunk Type: immed-start
Outgoing Dial Type: mf Incoming Dial Type: mf
Trunk Termination: rc
Digit Treatment: Digits:
Expected Digits: Sig Bit Inversion: none
Terminal Balanced? n RA Trunk Loss: 0db
Trunk Gain: high Drop Treatment: silence
Disconnect Supervision - In? y Out? n
Answer Supervision Timeout: 10 Receive Answer Supervision? n
Issue 1
32Argentina
Page 2 of 20
TRUNK FEATURES
ACA Assignment? n Measured: none
Maintenance Tests? y
Data Restriction? n
Suppress # Outpulsing? n
Page 3 of 10
TRUNK GROUP
ADMINISTRABLE TIMERS
Incoming Disconnect(msec): 500 Outgoing Disconnect(msec): 500
Incoming Dial Guard(msec): 70 Outgoing Dial Guard(msec): 1600
Incoming Glare Guard(msec): 1500 Outgoing Glare Guard(msec): 1500
Ringing Monitor(msec): 5200 Incoming Seizure(msec): 500
Outgoing End of Dial(sec): 10 Outgoing Seizure Response(sec): 5
Programmed Dial Pause(msec): 1500
Flash Length(msec): Incoming Incomplete Dial Alarm(sec): 255
END TO END SIGNALING
Tone(msec): 350 Pause(msec): 150
OUTPULSING INFORMATION
PPS: 10 Make(msec): 40 Break(msec): 60 PPM? n
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
June 1999
Application Notes for Type Approval
DID Trunk Group Administration
Page 4 of 10
TRUNK GROUP
Administered Members (min/max): 0/0
GROUP MEMBER ASSIGNMENTS Total Administered Members: 0
Port Code Sfx Name Night Mode Type Ans Delay
1:
2:
3:
Page 1 of 10
TRUNK GROUP
Group Number: Group Type: did CDR Reports: y
Group Name: OUTSIDE CALL COR: 1 TN: 1 TAC:
Country: 7
Auth Code? n
Issue 1
33Argentina
TRUNK PARAMETERS
Trunk Type: immed-start Incoming Rotary Timeout(sec): 5
Incoming Dial Type: tone
Trunk Termination: rc Disconnect Timing(msec): 500
Digit Treatment: Digits:
Expected Digits: Sig Bit Inversion: none
Terminal Balanced? n RA Trunk Loss: 0db
Extended Loop Range? n Trunk Gain: high Drop Treatment: silence
Disconnect Supervision - In? y
Page 2 of 10
TRUNK FEATURES
ACA Assignment? n Measured: none
Maintenance Tests? y
Data Restriction? n
Suppress # Outpulsing? n
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
Page 3 of 10
TRUNK GROUP
ADMINISTRABLE TIMERS
Incoming Disconnect(msec): 500
Incoming Dial Guard(msec): 70
Flash Length(msec): 540 Incoming Incomplete Dial Alarm(sec): 255
END TO END SIGNALING
Tone(msec): 350 Pause(msec): 150
Page 4 of 10
TRUNK GROUP
Administered Members (min/max): 0/0
GROUP MEMBER ASSIGNMENTS Total Administered Members: 0
Issue 1
June 1999
34Argentina
Port Code Sfx Name
1:
2:
3:
Digital Trunk Administration
This section does not list all possible valid administrable combinations. Rather
the most common or standard combination, compatible with public-network and
Type Approval standards for each country, is presented.
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
DS1 Programing for CO, DID and DIOD trunks
to the PTT using digital trunks
Page 1 of 1
DS1 CIRCUIT PACK
Location: Name: E-1CO, DID, DIOD
Bit Rate: 2.048 Line Coding: hdb3
Signaling Mode: CAS
Interconnect: CO Country Protocol: 7
Interface Companding: alaw CRC? n
Idle Code: 11111111
MAINTENANCE PARAMETERS
Slip Detection? n Near-end CSU Type: none
Tie Trunks
Issue 1
June 1999
35Argentina
■ Non-ISDN Signaling Example (DS1 Administration Screen)
— Circuit Pack: TN464D (Not entered as administrable item)
— Bit Rate: 2.048
— Interface Companding: mu-law
— Line Coding: HDB3
— Signaling Mode: CAS
— Country Protocol: 16
— Interconnect: pbx
—CRC?: no
— Idle Code: 01010100
— IS DN-P RI (P rivate Network) Signaling This example assumes use of
US Option 1 with facility associated signaling. Other feature options
will require changes in one or more administered items.
— DS1 Administration screen
■ Circuit Pack: TN464D (or TN464C from upgrades)
■ Bit Rate: 2.048
■ Interface Companding: A-law
■ Line Coding: HDB3
■ Signaling Mode: isdn-pri
■ Country Protocol: 1
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
— Connect: pbx
— Interface: user
—CRC: No
— Idle Code: 01010100
■ Signaling Group screen
— Associated Signaling: Yes
— Primary D_Channel: xxxx16 (xxxx=>depends on CP physical
location)
■ Trunk Group Administration screen
— Grou p Type: isdn-pri
— Service Type: tie
■ ISDN-PRI (P ublic Network)
Not available for this country.
Issue 1
June 1999
36Argentina
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
Australia
Table 16 shows the recommended circuit packs.
Table 16. Recommended and Available CPs in Australia
Equipment Equipment Type
Cabinet Type & Power GAC-MCC DC-MCC AC-SCC DC-SCC
AC-CSCC AC-CMC
AC Power Voltage & Freq 240V/50Hz
Ring Generator 20Hz 25Hz
Tone Detector >TN2182B >TN744D TN420C TN420B
Tone Clock >TN2182B TN780 TN419B
R2MFC Circuit n/a
Speech Synthesizer >TN457
Issue 1
June 1999
37Australia
Call Classifier >TN744D
Announcement >TN750C TN750B
Analog DID Trunk >TN436B TN436
Analog CO Trunk (No PPM) >TN2147C TN22147
Analog CO Trunk (w/PPM) #TN465C >TN438B
4 Wire Tie Tr unk TN437B TN437
2 Wire Tie Trunk >TN439
Auxiliary Trunk #TN763D >TN417
Digital CO/DID Trunk n/a
Digital Tie Trunk >TN464F TN464E TN464D TN464C
Digital PRI CO Trunk >TN464F TN464E TN464D TN464C
Digital BRI Trunk >TN2185
Digital Converter PRI-DASS
Digital Converter PRI-DPNSS TN-CCSC-2
Digital Converter PRI-BRI
8 Port Analog Line TN467
16 Port Analog Line #TN2183 >TN468B TN468
24 Port Analog Line TN2793
Continued on next page
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
Tab le 16 . Recommended and Available CPs in Australia — Continued
Equipment Equipment Type
4 Wire Digital Line >TN754B TN413
2 Wire Digital Line #TN2224 >TN2181
Data Line >TN726B
BRI-U Line
BRI-ST Line TN556B
NOTE:
Australia P2 signaling requires TN464Fv5 or later.
Country-Specific Features
Issue 1
June 1999
38Australia
Continued on next page
When the Country Code is 2, Malicious Call Trace notification is passed over the
following ISDN-PRI trunk groups: tandem, tie, access, and DMI-BOS. See
“M alicious Call Trace” in
Feature Administration
The screen displays shown in this section were effective the date the type
approval was awarded. The screens may have changed since that date.
Only those feature-related parameters that may have a Type Approval or basic
connectivity implication for a particular country are listed here.
■ ARS/AAR Administration
To enable ARS administration, on the System-Parameters
Customer-Options screen, set the
ARS/AAR defaults. All default ARS analysis codes are deleted before
dialed strings are added for routing when DEFINITY is installed outside of
North America. Be aware that the default for the 10 digits cause dialing
problems. In particular, the following call types (appear as ARS/AAR
defaults) typically are not used in non-North American ARS/AAR tables:
fnpa: North American numbers with an area code.
hnpa: North American numbers without an area code.
DEFINITY ECS Administrator’s Guide
ARS
field to y. You also should check all
.
svc: North American numbers of the screen ‘‘x11’’.
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
Lucent recommends only the following call types be used in Australia:
int: For all international numbers.
pubu: Fo r all other types of digit strings.
System Parameter Administration
Only those feature-related parameters that may have a Type Approval or basic
connectivity implication for a particular country are listed here.
■ Feature-Related System Parameters Administration
— Trunk-to-Trunk Transfer: Permitted by country’s regulations -
Selection is customer’s choice.
— Public Network Trunks on Conference Call: 5
— Conference Parties With PNTs: 6
— Conference Parties Without PNTs: 6
Issue 1
June 1999
39Australia
— Line Intercept Tone Timer: 30
— Night Service Disconnect Timer: 180 sec
— Short Interdigit Timer: 3 sec
— Unanswered DID Call Timer: 60
—Auto-Hold: Yes
1
— Attendant Tone: Yes
— Bri dging Tone: No
— Conference Tone: No
— Intrusion Tone: Yes
— Repetitive Call Waiting Tone: No
— DID Busy Treatment: Attendant
— Pull Transfer: No
— Level of Tone Detection: Precise
— Outpulse Without Tone: Yes
— (Station-to-switch) Recall Timing:
■ Flashhook Interval: Yes
■ Upper Bound: 1000 ms
■ Lower Bound: 200 ms
1. Although not a Type Approval issue, this represents the convention for this country.
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
■ System Parameter Country Options Administration
— Companding Mode: A-law
— Base Tone Generation Set: 2
— Tone Detection Mode: 2
— Interdigit Pause: short
— Digital Loss Plan: 2
— Analog Ringing Cadence: 2
Analog Trunk Administration
■ CO Trunks
— Trunk Group Screen
■ Group Type: CO
■ Country: 2
■ Trunk Gain: high
Issue 1
June 1999
40Australia
■ Direction: two-way
■ Digit Absorption List: blank
■ Prefix-1: No
■ Trunk Type: loop-star t
■ Outgoing Dial Type: tone
■ Trunk Termination: rc (complex impedance)
■ Auto Guard: yes
■ Dial Access: yes
■ Call Still Held: yes
■ Terminal Balanced: yes
■ Receive Answer Supervision: no
■ Answer Supervision Timeout: 10 (This sets both the CP
firmware timer and software timer. Set to 0 for any trunk that
will receive answer supervision.)
■ Disconnect Supervision - In: yes
■ Disconnect Supervision - Out: Selection is customer’s
choice.
■ Disconnect Timing: 500 msec (This field will not be used with
CPs that can accept the Incoming Disconnect and Outgoing
Disconnect timers. Set these latter two timers from the
Adm ini stra ble Timers Screen.)
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
— Trunk Group Administration Screen (Timing)
Set the following timers from the Administrable Timers screen
during administration of each trunk group. Select the following CO
trunk timer values for this country:
■ Incoming Disconnect: 500 ms
■ Outgoing Disconnect: 500 ms
■ Outgoing Dial Guard: 1600 ms
■ Incoming Glare Guard: 1500 ms
■ Outgoing Glare Guard: 1500 ms
■ Outgoing Dial Pulse Rate (PPS): 10 pps
■ Outgoing Rotary Digit Dial Make: 35 ms
■ Outgoing Rotary Digit Dial Break: 65 ms
■ Outgoing Rotary Dial Interdigit: 800 ms
■ Ring Monitor Timer: 5200 ms
Issue 1
June 1999
41Australia
■ Incoming Seizure: 500 ms
■ Outgoing End-of-Dial: 10 sec
■ Outgoing Seizure Response: 240 sec
■ Programmed Dial Pause: 1500 ms
■ Disconnect Signal Error: 240 sec
■ Flash Length: 100 ms
■ PPM: Yes
■ PPM Frequency: 50/12kHz
■ DID Trunks
— Trunk Group Screen
■ Group Type: DID
■ Country: 2
■ Trunk Gain: high
■ Digit Absorption List: blank
■ Incoming Dial Type: tone
■ Trunk Type: immed-start
■ Trunk Termination: rc (complex impedance)
■ Disconnect Supervision - In: yes
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
■ Disconnect Timing: 500 msec (This field will not be used with
CPs that can accept the Incoming Disconnect and Outgoing
Disconnect timers. Set these latter two timers from the
Adm ini stra ble Timers Screen.)
■ Digit Treatment: blank
■ Digits: blank
■ Expected Digits: depends on system size and numbering
plan
■ Terminal Balanced: yes
■ Extended Loop Range: (Used Only with TN459) no
■ Drop Treatment: silence
■ Incoming Rotary Timeout (sec): 5 sec (This field will not be
used with CPs that can accept the Incoming Partial Dial
timer. Set this timer from the Administrable Timers Screen.)
— Trunk Group Administration Screen (Timing)
Issue 1
June 1999
42Australia
Set the following timers from the Administrable Timers screen
during administration of each trunk group. Select the following DID
trunk timer values for this country:
■ Incoming Disconnect: 500 ms
■ Incoming Dial Guard: 50 ms
■ Incoming Partial Dial: 18 sec
■ Incoming Incomplete Dial: 255 sec
■ Flash Length: 100 ms
■ Tie Trunks
No special Type Approval regulations apply. Tie trunks are administered
on a case-by-case basis.
Digital Trunk Administration
This section does not list all possible valid administrable combinations. Rather
the most common or standard combination, compatible with public-network and
Type Approval standards for each country, is presented:
■ CO and DID Trunks
Not available in this country.
■ Tie Trunks
— Non-ISDN Signaling Example (DS1 Administration Screen)
■ Circuit Pack: TN464D (Not entered as administrable item;
TN464C from upgrades)
■ Bit Rate: 2.048
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
■ Interface Companding: A-law
■ Line Coding: HDB3
■ Signaling Mode: CAS
■ Country Protocol: 2
■ Interconnect: pbx
■ CRC?: no
■ Idle Code: 11111111
— ISDN-PRI (Private Network) Signaling
This example assumes use of US Option 1 with facility associated
signaling. Other feature options will require changes in one or more
administered items.
■ DS1 Administration screen
— Circuit Pack: TN464D (TN464C,B from upgrades)
— Bit Rate: 2.048
Issue 1
June 1999
43Australia
— Interface Companding: A-law
— Line Coding: HDB3
— Signaling Mode: isdn-pri
— Country Protocol: 2
— Connect: pbx
— Interface: user
—CRC: No
— Idle Code: 11111111
■ Signaling Group screen
— As sociate d Signaling: Yes
— Primary D_Channel: xxxx16 (xxxx=>depends on CP
physical location)
■ Trunk Group Administration screen
— Grou p Type: isdn-pri
— Service Type: tie
— ISDN-PRI (Public Network)
■ DS1 Administration screen
— Circuit Pack: TN464D (Not entered as administrable
item; TN464C from upgrades)
— Bit Rate: 2.048
— Interface Companding: A-law
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
— Line Coding: HDB3
— Signaling Mode: isdn-pri
— Country Protocol: 2
— Connect: Network
—CRC: No
— Idle Code: 11111111
■ Signaling Group screen
— As sociate d Signaling: Yes
— Primary D_Channel: xxxx16 (xxxx=>depends on CP
physical location)
■ Trunk Group Administration screen
— Grou p Type: isdn-pri
— Service Type: public_ntwrk
Issue 1
June 1999
44Australia
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
Belgium & Luxembourg
Table 17 shows the recommended circuit packs.
Table 17. Recommended and Available CPs in Belgium & Luxembourg
Equipment Equipment Type
Cabinet Type & Power GAC-MCC DC-MCC AC-SCC AC-CSCC
AC-CMC
AC Power Voltage & Freq 220V/50Hz
Ring Generator 25Hz
Tone Detector >TN2182B >TN744D TN420C
Tone Clock >TN2182B TN780
R2MFC Circuit >TN744D TN744B
Speech Synthesizer >TN457
Issue 1
June 1999
45Belgium & Luxembourg
Call Classifier >TN744D
Announcement TN750C TN750B
Analog DID Trunk >TN2146
Analog CO Trunk (No PPM) >TN2147C TN2147
Analog CO Trunk (w/PPM) #TN465C >TN465B
4 Wire Tie Trunk >TN760Dv11
2 Wire Tie Trunk n/a
Auxiliary Trunk >TN763D
Digital CO/DID Trunk >TN464F TN464E TN464D
Digital Tie Trunk >TN464F TN464E TN464D
Digital PRI CO Trunk >TN464F TN464E TN464D
Digital BRI Trunk >TN2185
Digital Converter PRI-DASS
Digital Converter PRI-DPNSS
Digital Converter PRI-BRI
8 Port Analog Line n/a
16 Port Analog Line #TN2183>TN2149
24 Port Analog Line n/a
Continued on next page
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
Tab le 17 . Recommended and Available CPs in Belgium & Luxembourg —
Continued
Equipment Equipment Type
4 Wire Digital Line >TN754B
2 Wire Digital Line #TN2224 >TN2181 TN2136
Data Line >TN726B
BRI-U Line
BRI-ST Line
Feature Administration
The screen displays shown in this section were effective the date the type
approval was awarded. The screens may have changed since that date.
Issue 1
June 1999
46Belgium & Luxembourg
Continued on next page
Only those feature-related parameters that may have a Type Approval or basic
connectivity implication for a particular country are listed here.
■ ARS/AAR Administration
To enable ARS administration, on the System-Parameters
Customer-Options screen, set the
ARS
field to y. You also should check all
ARS/AAR defaults. All default ARS analysis codes are deleted before
dialed strings are added for routing when DEFINITY is installed outside of
North America. Be aware that the default for the 10 digits cause dialing
problems. In particular, the following call types (appear as ARS/AAR
defaults) typically are not used in non-North American ARS/AAR tables:
fnpa: North American numbers with an area code.
hnpa: North American numbers without an area code.
svc: North American numbers of the screen ‘‘x11’’.
Lucent recommends only the following call types be used outside North
America:
int: For all international numbers.
natl: For all national PN numbers.
pubu: For all other external (that is, not extensions) numbers.
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
■ Route Pattern administration
— First Dial Tone Detection (always needed)
■ Number Delete Digits: 0
■ Inserted Digits: +
— Second Dial Tone Detection (needed on some analog CO trunks)
■ Number Delete Digits: 2 (Dialed String 00)
■ Inserted Digits: +00+
System Parameter Administration
Only those feature-related parameters that may have a Type Approval or basic
connectivity implication for a particular country are listed here.
■ Feature-Related System Parameters Administration
— Off Premise Tone Detection Timeout: 10 sec
— Trunk-to-Trunk Transfer: Not permitted in Belgium
Issue 1
June 1999
47Belgium & Luxembourg
— Distinctive Audible Alerting:
■ Int: 1
■ Ext: 2
■ Priority : 2
— DID/TIE/ISDN Intercept Treatment: Attendant
— Public Network Trunks on Conference Call: 1
— Conference Parties With PNTs: 3
— Conference Parties Without PNTs: 6
— Line Intercept Tone Timer: 30
— Night Service Disconnect Timer: 180 sec
— Short Interdigit Timer: 3 sec
— Unanswered DID Call Timer: 25 sec
—Auto-Hold: Yes
2
— Attendant Tone: Yes
— Bri dging Tone: No
— Conference Tone: No
— Intrusion Tone: Yes
— Repetitive Call Waiting Tone: Yes
2. Although not a Type Approval issue, this represents the convention for this country.
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
— DID Busy Treatment: Attendant
— Pull Transfer: No
— Level of Tone Detection: Medium
— Outpulse Without Tone: Yes
— (Station-to-switch) Recall Timing:
■ Flashhook Interval: No
■ Disconnect Timing: 350 ms
— Network Feedback During Tone Detection: No
■ System Parameter Multifrequency Signaling Administration
— Incoming Call Type: non-group-ii-mfc (use default translations)
— Test Call Extension: 160 or as negotiated.
■ System Parameter Country Options Administration
— Companding Mode: A-law
Issue 1
June 1999
48Belgium & Luxembourg
— Base Tone Generation Set: 8
— Tone Detection Mode: 5
— Digital Loss Plan: 8
— Interdigit Pause: long
— Dial Tone Validation Timer: 600 ms
— Analog Ringing Cadence: 8
— Customized Indivi dual Tones
Customized tone definitions follow the syntax as specified:
[(Frequency/Level)|silence|goto)][(Duration ms)|(Step)]
■ Intercept Tone:
1. (425/-4)(250)
2. (silence)(250)
3. (goto)(1)
■ Conference Tone:
1. (425/-11)(200)
2. (silenc e) (9800)
3. (goto)(1)
■ 1 Call Wait Tone:
1. (425/-11)(200)
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
■ 2 Call Wait Tone:
1. (425/-11)(200)
Analog Trunk Administration
■ CO Trunks
— Trunk Group Screen
■ Group Type: CO
■ Direction: two-way
NOTE:
All trunks in Belgium are one-way but outgoing trunks
must be marked two-way in order to be able to select
cyclical hunt = y.
■ Digit Absorption List: blank
■ Country Code: 8
Issue 1
June 1999
49Belgium & Luxembourg
Trunk Gain Loop Length
high long
low short
■ Dial Access: No
■ Prefix-1: No
■ Trunk Type: loop-star t
■ Outgoing Dial Type:
— Digital Trunks: tone
— Analog Trunks: tone or rotary
■ Trunk Termination: rc (complex impedance)
■ Auto Guard: no
■ Sig Bit Inversion: none
■ Call Still Held: no
■ Terminal Balanced: no
RA Trunk Loss Loop Length
2dB long
0dB short
■ Receive Answer Supervision: no
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
■ Answer Supervision Timeout: 10 (This sets both the CP
firmware timer and software timer. Set to 0 for any trunk that
will receive answer supervision.)
■ Disconnect Supervision - In:
— Analog Trunks: no
— Digital Trunks: yes
■ Disconnect Supervision - Out: Selection is customer’s
choice.
■ Disconnect Timing: 500 msec (This field will not be used for
CPs that can accept the Incoming Disconnect and Outgoing
Disconnect timers. Set these latter two timers from the
Adm ini stra ble Timers Screen.)
■ Cyclical Hunt: Yes
■ Suppress # Outpulsing: yes
— Trunk Group Administration Screen (Timing)
Issue 1
June 1999
50Belgium & Luxembourg
Set the following timers from the Administrable Timers screen
during administration of each trunk group. Select the following CO
trunk timer values for this country:
■ Incoming Disconnect: 600 ms
■ Outgoing Disconnect: 500 ms
■ Outgoing Dial Guard: 1600 ms
■ Incoming Glare Guard: 1500 ms
■ Outgoing Glare Guard: 1500 ms
■ Outgoing Dial Pulse Rate (PPS): 10 pps
■ Outgoing Rotary Digit Dial Make: 35 ms
■ Outgoing Rotary Digit Dial Break: 65 ms
■ Outgoing Rotary Dial Interdigit: 800 ms
■ Ring Monitor Timer: 5200 ms
■ Incoming Seizure: 500 ms
■ Outgoing End-of-Dial: 10 sec
■ Outgoing Seizure Response:
— Analog trunks: 10 sec
— Digital trunks: 2 sec
■ Programmed Dial Pause: 1500 ms
■ End-To-End Signaling Pause: 150 ms (accept default)
■ End-To-End Signaling Tone: 350 ms (accept default)
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
■ PPM: yes
■ Frequency: 16 khz
■ Flash Length: 100 ms
■ DID Trunks
— Trunk Group Screen
■ Group Type: DID
■ Direction: incoming
■ Country Code: 8
■ Trunk Gain: high or low as required by loop length
■ Digit Absorption List: blank
■ Incoming Dial Type: MF
■ Trunk Type: immed-start
■ Trunk Termination: rc (complex impedance)
Issue 1
June 1999
51Belgium & Luxembourg
■ Disconnect Timing: 500 msec (This field will not be used with
CPs that can accept the Incoming Disconnect and Outgoing
Disconnect timers. Set these latter two timers from the
Adm ini stra ble Timers Screen.)
■ Digit Treatment: blank
■ Digits: blank
■ Expected Digits: 3 or 4
■ Terminal Balanced: no
■ RA Trunk Loss: 0dB
■ Extended Loop Range: (Used Only with TN459) no
■ Drop Treatment: silence
■ Disconnect Supervision:
— Analog Trunks: no
— Digital Trunks: yes
■ Incoming Rotary Timeout (sec): 5 sec (This field will not be
used with CPs that can accept the Incoming Partial Dial
timer. Set this timer from the Administrable Timers Screen.)
■ Suppress # Outpulsing: yes
— Trunk Group Administration Screen (Timing)
Set the following timers from the Administrable Timers screen
during administration of each trunk group. Select the following DID
trunk timer values for this country:
■ Incoming Disconnect: 600 ms
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
■ Incoming Dial Guard: 50 ms
■ Incoming Partial Dial: 18 sec
■ Incoming Incomplete Dial: 60 sec
■ Flash Length: 100 ms
■ Tie Trunks
No special Type Approval regulations apply. Tie trunks are administered
on a case-by-case basis.
Digital Trunk Administration
This section does not list all possible valid administrable combinations: Only the
most common or standard combination, compatible with public-network and
Type Approval standards for each country, is presented:
■ CO Trunks
— DS1 Administration Screen
■ Circuit Pack: TN464D
Issue 1
June 1999
52Belgium & Luxembourg
■ Bit Rate: 2.048
■ Interface Companding: A-law
■ Line Coding: HDB3
■ Signaling Mode: CAS
■ Country Protocol: 8
■ Interconnect: CO
■ CRC?: No
■ Idle Code: 01010100
— Trunk Group Administration Screen (Timing)
Digital trunk timing values should be set as for analog CO trunks
with the following exception.
■ Outgoing Seizure Response: 2 sec.
■ DID Trunks
— DS1 Administration Screen
■ Circuit Pack: TN464D
■ Bit Rate: 2.048
■ Interface Companding: A-law
■ Line Coding: HDB3
■ Signaling Mode: CAS
■ Country Protocol: 8
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
■ Interconnect: CO
■ CRC?: No
■ Idle Code: 01010100
— Trunk Group Administration Screen (Timing)
Digital trunk timing values should be set as for analog DID trunks.
■ Tie Trunks
— Non-ISDN Signaling Example (DS1 Administration screen)
■ Circuit Pack: TN464D
■ Bit Rate: 2.048
■ Interface Companding: A-law
■ Line Coding: HDB3
■ Signaling Mode: CAS
■ Country Protocol: 8
Issue 1
June 1999
53Belgium & Luxembourg
■ Interconnect: pbx
■ CRC?: no
■ Idle Code: 01010100
— ISDN-PRI (Private Network) Signaling
This example assumes use of US Option 1 with facility associated
signaling. Other feature options will require changes in one or more
administered items.
— DS1 Administration screen
■ Circuit Pack: TN464D
■ Bit Rate: 2.048
■ Interface Companding: A-law
■ Line Coding: HDB3
■ Signaling Mode: isdn-pri
■ Country Protocol: 8
■ Connect: pbx
■ Interface: user
■ CRC: No
■ Idle Code: 01010100
— Signaling Group screen
■ Assoc i ate d Signalin g: Yes
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
■ Primary D_Channel: xxxx16 (xxxx=>depends on CP
physical location)
— Trunk Group Administration screen
■ Grou p Type: isdn-pri
■ Service Type: tie
■ ISDN-PRI (P ublic Network)
Not available for this country.
Station Administration
Rotary stations are not supported in Belgium.
■ Type: 2500
■ Switch Hook Flash: yes
■ Call Vector screen
Use this with Auto T ransfer and Auto Answer through vectoring/prompting,
and only for Digital outgoing trunks.
Issue 1
June 1999
54Belgium & Luxembourg
— ASAI Routing: no
—Basic: yes
—Prompting: yes
— Wait time 6 seconds hearing ringback
— Announcement extension is installation dependent
— Route to number is installation dependent if unconditionally
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
Bolivia
Table 18 shows the recommended circuit packs.
Table 18. Recommended and Available CPs in Bolivia
Equipment Equipment Type
Cabinet Type & Power GAC-MCC DC-MCC AC-SCC AC-CSCC
AC-CMC
AC Power Voltage & Freq 220V/50Hz
Ring Generator 20Hz
Tone Detector >TN2182B >TN744D
Tone Clock >TN2182B TN780 TN768
R2MFC Circuit >TN744D TN744B
Speech Synthesizer >TN725B
Issue 1
June 1999
55Bolivia
Call Classifier >TN744D
Announcement >TN750C TN750B
Analog DID Trunk
Analog CO Trunk (No PPM) >TN747B
Analog CO Trunk (w/PPM)
4 Wire Tie Trunk >TN760D
2 Wire Tie Trunk
Auxiliary Trunk >TN763D
Digital CO/DID Trunk >TN464F TN464E TN464D
Digital Tie Trunk >TN464F TN464E TN464D
Digital PRI CO Trunk
Digital BRI Trunk
Digital Converter PRI-DASS
Digital Converter PRI-DPNSS
Digital Converter PRI-BRI
8 Port Analog Line
16 Port Analog Line >TN746B
24 Port Analog Line n/a
Continued on next page
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
Tab le 18 . Recommended and Available CPs in Bolivia — Continued
Equipment Equipment Type
4 Wire Digital Line >TN754B
2 Wire Digital Line >TN2224 >TN2181
Data Line >TN726B
BRI-U Line
BRI-ST Line
Feature Administration
The screen displays shown in this section were effective the date the type
approval was awarded. The screens may have changed since that date.
Issue 1
June 1999
56Bolivia
Continued on next page
Only those feature-related parameters that may have a Type Approval or basic
connectivity implication for a particular country are listed here.
■ ARS/AAR Administration
To enable ARS administration, on the System-Parameters
Customer-Options screen, set the
ARS
field to y. You also should check all
ARS/AAR defaults. All default ARS analysis codes are deleted before
dialed strings are added for routing when DEFINITY is installed outside of
North America. Be aware that the default for the 10 digits cause dialing
problems. In particular, the following call types (appear as ARS/AAR
defaults) typically are not used in non-North American ARS/AAR tables:
fnpa: North American numbers with an area code.
hnpa: North American numbers without an area code.
svc: North American numbers of the screen ‘‘x11’’.
Lucent recommends only the following call types be used outside North
America:
int: For all international numbers.
natl: For all national PN numbers.
pubu: For all other external (that is, not extensions)
numbers.
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
System Administration
Feature-Related System Parameters
Page 1 of 6
FEATURE-RELATED SYSTEM PARAMETERS
Trunk-to-Trunk Transfer: all
Coverage - Subsequent Redirection No Answer Interval: 2
Coverage - Caller Response Interval (seconds): 4
Keep Held SBA at Coverage Point? y
Automatic Callback - No Answer Timeout Interval (rings): 3
Call Park Timeout Interval (minutes): 10
Off-Premises Tone Detect Timeout Interval (seconds): 20
AAR/ARS Dial Tone Required? y
Music/Tone on Hold: none
Music (or Silence) on Transferred Trunk Calls? no
DID/Tie/ISDN Intercept Treatment: attd
Internal Automatic Answer for Attendant Extended Calls? n
Automatic Circuit Assurance (ACA) Enabled? n
Issue 1
June 1999
57Bolivia
Page 2 of 6
FEATURE-RELATED SYSTEM PARAMETERS
LEAVE WORD CALLING PARAMETERS
Maximum Number of Messages Per Station (when MSA not in service):10
Stations with System-wide Retrieval Permission (enter extension)
1: 2: 3: 4: 5:
6: 7: 8: 9: 10:
WARNING! SEE USER DOCUMENTATION BEFORE CHANGING TTI STATE
Terminal Translation Initialization (TTI) Enabled? n
External Coverage Treatment for Transferred Incoming Calls? n
SECURITY VIOLATION NOTIFICATION (SVN) PARAMETERS HAVE MOVED TO
THE SYSTEM-PARAMETERS SECURITY SCREEN
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
Page 3 of 6
FEATURE-RELATED SYSTEM PARAMETERS
Reserved Slots for Attendant Priority Queue: 5
Time before Off-hook Alert: 10
Emergency Access Redirection Extension:
Service Observing Warning Tone? y
Number of Emergency Calls Allowed in Attendant Queue: 5
Call Pickup Alerting? n
Deluxe Paging and Call Park Timeout to Originator? n
Controlled Outward Restriction Intercept Treatment: tone
Controlled Termination Restriction (Do Not Disturb): tone
Controlled Station to Station Restriction: tone
AUTHORIZATION CODE PARAMETERS Authorization Codes Enabled?
Authorization Code Length:
Authorization Code Cancellation Symbol: #
Attendant Time Out Flag? n
Display Authorization Code? y
Issue 1
June 1999
58Bolivia
Page 4 of 6
FEATURE-RELATED SYSTEM PARAMETERS
SYSTEM PRINTER PARAMETERS
System Printer Extension: Lines Per Page: 60
SYSTEM-WIDE PARAMETERS
Switch Name:
CALL CENTER SYSTEM PARAMETERS
Direct Agent Announcement Extension:
Direct Agent Announcement Delay:
Converse Delay Data1: 0 Data2: 2
Direct Agent Announcement Extension: Converse Pulse ON: 100 OFF: 70
Prompting Timeout (secs): 10
CALL MANAGEMENT SYSTEM PARAMETERS
BCMS/VuStats Measurement Interval: hour
BCMS/VuStats Abandon Call Timer (seconds): Validate Login IDs? n
ACD Login Identification Length: Adjunct CMS Release:
MALICIOUS CALL TRACE PARAMETERS
Apply MCT Warning Tone? n MCT Voice Recorder Trunk Group:
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
Page 5 of 6
FEATURE-RELATED SYSTEM PARAMETERS
Public Network Trunks on Conference Call: 5 Auto Start? n
Conference Parties with Public Network Trunks: 6 Auto Hold? n
Conference Parties without Public Network Trunks: 6 Attendant Tone? y
Night Service Disconnect Timer (seconds): 180 Bridging Tone? n
Short Interdigit Timer (seconds): 3 Conference Tone? n
Unanswered DID Call Timer (seconds): Intrusion Tone? n
Line Intercept Tone Timer (seconds): 30
DID Busy Treatment: tone
Allow AAR/ARS Access from DID/DIOD? n
DISTINCTIVE AUDIBLE ALERTING
Internal: 1 External: 2 Priority: 3
Attendant Originated Calls: external
Page 6 of 6
FEATURE-RELATED SYSTEM PARAMETERS
Issue 1
June 1999
59Bolivia
Pull Transfer: n Update Transferred Ring Pattern? n
Outpulse Without Tone? y Wait Answer Supervision Timer? y
Repetitive Call Waiting Tone? n
Allow Conference via Flash? y
Vector Disconnect Timer (min): Network Feedback During Tone Detection? y
Hear Zip Tone Following VOA? n
Intercept Treatment On Failed Trunk Transfers? n
Station Tone Forward Disconnect: silence
Level Of Tone Detection: precise
RECALL TIMING
Flashhook Interval? y Upper Bound (msec): 1000
Lower Bound (msec): 200
ENHANCED DCS
Enhanced DCS Enabled? n
Apply Intercept Locally? y Enforce PNT-to-PNT Restrictions? n
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
June 1999
Application Notes for Type Approval
Multifrequency-Signaling-Related System
Parameters
Page 1 of 3
MULTIFREQUENCY-SIGNALING-RELATED SYSTEM PARAMETERS
Incoming Call Type: group-ii-mfc
Outgoing Call Type: group-ii-mfc
Maintenance Call Type: none
Test Call Extension:
Interdigit Timer (sec): 10
Outgoing Forward Signal Present Timer (sec): 15
Outgoing Forward Signal Absent Timer (sec): 30
Multifrequency Signaling Incoming Intercept Treatment? n
Received Signal Gain(-Loss) (dB): 0
Transmitted Signal Gain(-Loss) (dB): -3
ANI Prefix:
ANI for PBX:
Next ANI Digit: send-ani
ANI Prefix: Collect All Digits Before Seizure? n
Request Incoming ANI (non-AAR/ARS)? n
Called Party Category: user-type
Use COR for Calling Party Category? n
Issue 1
60Bolivia
Page 2 of 3
MULTIFREQUENCY-SIGNALING-RELATED SYSTEM PARAMETERS
INCOMING FORWARD SIGNAL TYPES INCOMING BACKWARD SIGNAL TYPES
(Tones from CO) (Tones to CO)
Group-I Group-II Group-A Group-B
11: ignored 1: normal 1: next-digit 1: free
12: ignored 2: normal 3: end-of-dial 2: busy
13: ignored 3: normal 4: congestion
14: ignored 4: normal 7: intercept
15: ignored 5: normal
6: normal
7: normal
8: normal
9: normal
10: normal
11: normal
12: normal
13: normal
14: normal
15: normal
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
June 1999
Application Notes for Type Approval
Page 3 of 3
MULTIFREQUENCY-SIGNALING-RELATED SYSTEM PARAMETERS
OUTGOING FORWARD SIGNAL TYPES OUTGOING BACKWARD SIGNAL TYPES
(Tones to CO) (Tones from CO)
Group-I Group-II Group-A Group-B
12: ani-not-avail 2: normal 1: next-digit 1: free
15: end-of-ani 1: attendant 2: congestion 2: busy
6: data-call 3: end-of-dial 3: congestion
4: congestion 4: congestion
5: send-ani 5: congestion
6: congestion 6: free
7: last-2-digits 7: intercept
8: last-3-digits 8: congestion
9: congestion 9: congestion
10: congestion 10: congestion
11: congestion 11: congestion
12: congestion 12: congestion
13: congestion 13: congestion
14: congestion 14: congestion
15: congestion 15: congestion
Issue 1
61Bolivia
System Parameters Country-Options
Page 1 of 7
SYSTEM PARAMETERS COUNTRY-OPTIONS
Companding Mode: A-Law Base Tone Generator Set: 1
440Hz PBX-dial Tone? y 440Hz Secondary-dial Tone? y
Digital Loss Plan: 1
Analog Ringing Cadence: 1
TONE DETECTION PARAMETERS
Tone Detection Mode: 6
Interdigit Pause: short
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
June 1999
Application Notes for Type Approval
Page 2 of 7
SYSTEM PARAMETERS COUNTRY-OPTIONS
Tone Name Cadence Tone
Step (Frequency/Level)
Busy-Tone 1: 400/-11.0Hz Duration (mses) 500
2: Silence Duration (mses) 500
3: Goto Step 1
4:
5:
6:
7:
8:
9:
10:
Trunk Group Administration
Issue 1
62Bolivia
CO Trunk Group Administration
Page 1 of 10
TRUNK GROUP
Group Number: Group Type: co CDR Reports: y
Group Name: OUTSIDE CALL COR: 1 TN: 1 TAC:
Direction: two-way Outgoing Display? n
Dial Access? n Busy Threshold: 99 Night Service:
Queue Length: 0 Country: 1 Incoming Destination:
Comm Type: voice Auth Code? n Digit Absorption List:
Prefix-1? n Trunk Flash? n Toll Restricted? n
TRUNK PARAMETERS
Trunk Type: loop-start
Outgoing Dial Type: tone Cut-Through? n
Trunk Termination: rc Disconnect Timing(msec): 500
Auto Guard? n Call Still Held? n Sig Bit Inversion: none
Terminal Balanced? n RA Trunk Loss: 0db
Trunk Gain: high
Disconnect Supervision - In? n Out? n Cyclical Hunt? n
Answer Supervision Timeout: 10 Receive Answer Supervision? n
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
June 1999
Application Notes for Type Approval
Page 2 of 10
TRUNK FEATURES
ACA Assignment? n Measured: none
Maintenance Tests? y
Data Restriction? n
Abandoned Call Search? n
Suppress # Outpulsing? n
Page 3 of 10
TRUNK GROUP
ADMINISTRABLE TIMERS
Incoming Disconnect(msec): 500 Outgoing Disconnect(msec): 500
Outgoing Dial Guard(msec): 1600
Incoming Glare Guard(msec): 1500 Outgoing Glare Guard(msec): 1500
Ringing Monitor(msec): 5200 Incoming Seizure(msec): 500
Outgoing End of Dial(sec): 10 Outgoing Seizure Response(sec): 5
Programmed Dial Pause(msec): 1500
Flash Length(msec): 540
Issue 1
63Bolivia
END TO END SIGNALING
Tone(msec): 350 Pause(msec): 150
OUTPULSING INFORMATION
PPS: 10 Make(msec): 40 Break(msec): 60 PPM? n
Page 4 of 10
TRUNK GROUP
Administered Members (min/max): 0/0
Total Administered Members: 0
GROUP MEMBER ASSIGNMENTS
Port Code Sfx Name Night Mode Type Ans Delay
1:
2:
3:
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
June 1999
Application Notes for Type Approval
DIOD Trunk Group Administration
Page 1 of 10
TRUNK GROUP
Group Number: Group Type: diod CDR Reports: y
Group Name: OUTSIDE CALL COR: 1 TN: 1 TAC:GG
Direction: two-way Outgoing Display? n
Dial Access? n Busy Threshold: 99
Queue Length: 0 Country: 1
Auth Code? n Digit Absorption List:
Prefix-1? n Trunk Flash? n Toll Restricted? n
TRUNK PARAMETERS
Trunk Type: immed-start
Outgoing Dial Type: mf Incoming Dial Type: mf
Trunk Termination: rc
Digit Treatment: Digits:
Expected Digits: Sig Bit Inversion: none
Terminal Balanced? n RA Trunk Loss: 0db
Trunk Gain: high Drop Treatment: silence
Disconnect Supervision - In? y Out? n
Answer Supervision Timeout: 10 Receive Answer Supervision? n
Issue 1
64Bolivia
Page 2 of 20
TRUNK FEATURES
ACA Assignment? n Measured: none
Maintenance Tests? y
Data Restriction? n
Suppress # Outpulsing? n
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
Page 3 of 10
TRUNK GROUP
ADMINISTRABLE TIMERS
Incoming Disconnect(msec): 500 Outgoing Disconnect(msec): 500
Incoming Dial Guard(msec): 70 Outgoing Dial Guard(msec): 1600
Incoming Glare Guard(msec): 1500 Outgoing Glare Guard(msec): 1500
Ringing Monitor(msec): 5200 Incoming Seizure(msec): 500
Outgoing End of Dial(sec): 10 Outgoing Seizure Response(sec): 5
Programmed Dial Pause(msec): 1500
Flash Length(msec): Incoming Incomplete Dial Alarm(sec): 255
END TO END SIGNALING
Tone(msec): 350 Pause(msec): 150
OUTPULSING INFORMATION
PPS: 10 Make(msec): 40 Break(msec): 60 PPM? n
Issue 1
June 1999
65Bolivia
Page 4 of 10
TRUNK GROUP
Administered Members (min/max): 0/0
GROUP MEMBER ASSIGNMENTS Total Administered Members: 0
Port Code Sfx Name Night Mode Type Ans Delay
1:
2:
3:
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
June 1999
Application Notes for Type Approval
DID Trunk Group Administration
Page 1 of 10
TRUNK GROUP
Group Number: Group Type: did CDR Reports: y
Group Name: OUTSIDE CALL COR: 1 TN: 1 TAC:
Country: 1
Auth Code? n
TRUNK PARAMETERS
Trunk Type: immed-start Incoming Rotary Timeout(sec): 5
Incoming Dial Type: tone
Trunk Termination: rc Disconnect Timing(msec): 500
Digit Treatment: Digits:
Expected Digits: Sig Bit Inversion: none
Terminal Balanced? n RA Trunk Loss: 0db
Extended Loop Range? n Trunk Gain: high Drop Treatment: silence
Disconnect Supervision - In? y
Issue 1
66Bolivia
Page 2 of 10
TRUNK FEATURES
ACA Assignment? n Measured: none
Maintenance Tests? y
Data Restriction? n
Suppress # Outpulsing? n
Page 3 of 10
TRUNK GROUP
ADMINISTRABLE TIMERS
Incoming Disconnect(msec): 500
Incoming Dial Guard(msec): 70
Flash Length(msec): 540 Incoming Incomplete Dial Alarm(sec): 255
END TO END SIGNALING
Tone(msec): 350 Pause(msec): 150
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
Page 4 of 10
TRUNK GROUP
Administered Members (min/max): 0/0
GROUP MEMBER ASSIGNMENTS Total Administered Members: 0
Port Code Sfx Name
1:
2:
3:
DS1 for CO, DID and DIOD Trunks to the PTT
Using Digital Trunks
Page 1 of 1
Issue 1
June 1999
67Bolivia
DS1 CIRCUIT PACK
Location: Name: E-1CO, DID, DIOD
Bit Rate: 2.048 Line Coding: hdb3
Signaling Mode: CAS
Interconnect: CO Country Protocol: 7
Interface Companding: alaw CRC? n
Idle Code: 11111111
MAINTENANCE PARAMETERS
Slip Detection? n Near-end CSU Type: other
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
Brazil
Table 19 shows the recommended circuit packs.
Table 19. Recommended and Available CPs in Brazil
Equipment Equipment Type
Cabinet Type & Power GAC-MCC AC-MCC DC-MCC AC-SCC
DC-SCC AC-CSCC AC-CMC
AC Power Voltage & Freq 127V/60Hz 220V/60Hz
Ring Generator 25Hz
Tone Detector >TN2182B >TN744D TN748D
Tone Clock >TN2182B TN780
R2MFC Circuit >TN744D TN744B
Speech Synthesizer >TN725B
Issue 1
June 1999
68Brazil
Call Classifier >TN744D
Announcement >TN750C TN750B
Analog DID Trunk >TN753
Analog CO Trunk (No PPM)
Analog CO Trunk (w/PPM) >TN465C TN465B
4 Wire Tie Trunk >TN2140B
2 Wire Tie Trunk >TN439
Auxiliary Trunk >TN763D
Digital CO/DID Trunk >TN464F TN464E TN464D TN464C
Digital Tie Trunk >TN464F TN464E TN464D TN464C
Digital PRI CO Trunk >TN464F TN464E TN464D TN464C
Digital BRI Trunk
Digital Converter PRI-DASS
Digital Converter PRI-DPNSS
Digital Converter PRI-BRI
8 Port Analog Line n/a
16 Port Analog Line >TN746B
24 Port Analog Line n/a
Continued on next page
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
Tab le 19 . Recommended and Available CPs in Brazil — Continued
Equipment Equipment Type
4 Wire Digital Line >TN754B
2 Wire Digital Line #TN2224 >TN2181
Data Line >TN726B
BRI-U Line TN2198
BRI-ST Line TN556B
Country-Specific Feature
When not using the Block Collect Call feature, the Country field should be 16.
Issue 1
June 1999
69Brazil
Continued on next page
NOTE:
Block Collect Call requires TN753 v22 or later for DID trunks, TN464F v9 or
later for DS1 trunks, and TN465C (all vintages) for analog CO trunks.
NOTE:
The 900 ohms feature requires TN465CV2 or later for analog CO circuit
packs, and either TN2155V3 or later or TN2183BV4 or later for analog line
circuit packs.
Feature Administration
The screen displays shown in this section were effective the date the type
approval was awarded. The screens may have changed since that date.
Only those feature-related parameters that may have a Type Approval or basic
connectivity implication for a particular country are listed here.
■ ARS/AAR Administration
To enable ARS administration, on the System-Parameters
Customer-Options screen, set the
ARS/AAR defaults. All default ARS analysis codes are deleted before
dialed strings are added for routing when DEFINITY is installed outside of
North America. Be aware that the default for the 10 digits cause dialing
problems. In particular, the following call types (appear as ARS/AAR
defaults) typically are not used in non-North American ARS/AAR tables:
ARS
field to y. You also should check all
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
fnpa: North American numbers with an area code.
hnpa: North American numbers without an area code.
svc: North American numbers of the screen ‘‘x11’’.
Lucent recommends only the following call types be used outside North
America:
int: For all international numbers.
natl: For all national PN numbers.
pubu: For all other external (that is, not extensions) numbers.
System Parameter Administration
Issue 1
June 1999
70Brazil
Feature-Related System Parameters
Page 1 of 6
FEATURE-RELATED SYSTEM PARAMETERS
Trunk-to-Trunk Transfer: all
Coverage - Subsequent Redirection No Answer Interval: 2
Coverage - Caller Response Interval (seconds): 4
Keep Held SBA at Coverage Point? y
Automatic Callback - No Answer Timeout Interval (rings): 3
Call Park Timeout Interval (minutes): 10
Off-Premises Tone Detect Timeout Interval (seconds): 20
AAR/ARS Dial Tone Required? y
Music/Tone on Hold: none
Music (or Silence) on Transferred Trunk Calls? no
DID/Tie/ISDN Intercept Treatment: attd
Internal Automatic Answer for Attendant Extended Calls? n
Automatic Circuit Assurance (ACA) Enabled? n
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
Page 2 of 6
FEATURE-RELATED SYSTEM PARAMETERS
LEAVE WORD CALLING PARAMETERS
Maximum Number of Messages Per Station (when MSA not in service):10
Stations with System-wide Retrieval Permission (enter extension)
1: 2: 3: 4: 5:
6: 7: 8: 9: 10:
WARNING! SEE USER DOCUMENTATION BEFORE CHANGING TTI STATE
Terminal Translation Initialization (TTI) Enabled? n
External Coverage Treatment for Transferred Incoming Calls? n
SECURITY VIOLATION NOTIFICATION (SVN) PARAMETERS HAVE MOVED TO
THE SYSTEM-PARAMETERS SECURITY SCREEN
Issue 1
June 1999
71Brazil
Page 3 of 6
FEATURE-RELATED SYSTEM PARAMETERS
Reserved Slots for Attendant Priority Queue: 5
Time before Off-hook Alert: 10
Emergency Access Redirection Extension:
Service Observing Warning Tone? y
Number of Emergency Calls Allowed in Attendant Queue: 5
Call Pickup Alerting? n
Deluxe Paging and Call Park Timeout to Originator? n
Controlled Outward Restriction Intercept Treatment: tone
Controlled Termination Restriction (Do Not Disturb): tone
Controlled Station to Station Restriction: tone
AUTHORIZATION CODE PARAMETERS Authorization Codes Enabled?
Authorization Code Length:
Authorization Code Cancellation Symbol: #
Attendant Time Out Flag? n
Display Authorization Code? y
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
Page 4 of 6
FEATURE-RELATED SYSTEM PARAMETERS
SYSTEM PRINTER PARAMETERS
System Printer Extension: Lines Per Page: 60
SYSTEM-WIDE PARAMETERS
Switch Name:
CALL CENTER SYSTEM PARAMETERS
Direct Agent Announcement Extension:
Direct Agent Announcement Delay:
Converse Delay Data1: 0 Data2: 2
Direct Agent Announcement Extension: Converse Pulse ON: 100 OFF: 70
Prompting Timeout (secs): 10
CALL MANAGEMENT SYSTEM PARAMETERS
BCMS/VuStats Measurement Interval: hour
BCMS/VuStats Abandon Call Timer (seconds): Validate Login IDs? n
ACD Login Identification Length: Adjunct CMS Release:
MALICIOUS CALL TRACE PARAMETERS
Apply MCT Warning Tone? n MCT Voice Recorder Trunk Group:
Issue 1
June 1999
72Brazil
Page 5 of 6
FEATURE-RELATED SYSTEM PARAMETERS
Public Network Trunks on Conference Call: 5 Auto Start? n
Conference Parties with Public Network Trunks: 6 Auto Hold? n
Conference Parties without Public Network Trunks: 6 Attendant Tone? y
Night Service Disconnect Timer (seconds): 180 Bridging Tone? n
Short Interdigit Timer (seconds): 3 Conference Tone? n
Unanswered DID Call Timer (seconds): Intrusion Tone? n
Line Intercept Tone Timer (seconds): 30
DID Busy Treatment: tone
Allow AAR/ARS Access from DID/DIOD? n
DISTINCTIVE AUDIBLE ALERTING
Internal: 1 External: 2 Priority: 3
Attendant Originated Calls: external
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
June 1999
Application Notes for Type Approval
Page 6 of 6
FEATURE-RELATED SYSTEM PARAMETERS
Pull Transfer: n Update Transferred Ring Pattern? n
Outpulse Without Tone? n Wait Answer Supervision Timer? n
Repetitive Call Waiting Tone? n
Allow Conference via Flash? y
Vector Disconnect Timer (min): Network Feedback During Tone Detection? y
Hear Zip Tone Following VOA? n
Intercept Treatment On Failed Trunk Transfers? n
Station Tone Forward Disconnect: busy
Level Of Tone Detection: precise
RECALL TIMING
Flashhook Interval? y Upper Bound (msec): 1000
Lower Bound (msec): 200
ENHANCED DCS
Enhanced DCS Enabled? n
Apply Intercept Locally? y Enforce PNT-to-PNT Restrictions? n
Issue 1
73Brazil
Multifrequency-Signaling-Related System
Parameters
Page 1 of 3
MULTIFREQUENCY-SIGNALING-RELATED SYSTEM PARAMETERS
Incoming Call Type: group-ii-mfc
Outgoing Call Type: group-ii-mfc
Maintenance Call Type: none
Test Call Extension:
Interdigit Timer (sec): 7
Outgoing Forward Signal Present Timer (sec): 20
Outgoing Forward Signal Absent Timer (sec): 30
Multifrequency Signaling Incoming Intercept Treatment? n
Received Signal Gain(-Loss) (dB): 0
Transmitted Signal Gain(-Loss) (dB): -3
ANI Prefix:
ANI for PBX:
Next ANI Digit: send-ani
ANI Prefix: Collect All Digits Before Seizure? n
Request Incoming ANI (non-AAR/ARS)? n
Called Party Category: user-type
Use COR for Calling Party Category? n
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
Page 2 of 3
MULTIFREQUENCY-SIGNALING-RELATED SYSTEM PARAMETERS
INCOMING FORWARD SIGNAL TYPES INCOMING BACKWARD SIGNAL TYPES
(Tones from CO) (Tones to CO)
Group-I Group-II Group-A Group-B
11: ignored 1: normal 1: next-digit 1: free
12: ani-not-avail 2: normal 3: end-of-dial 2: busy
13: ignored 3: normal 4: congestion 4: congestion
14: ignored 4: normal 5: send-ani 7: intercept
15: and-of-ani 5: attendant
6: data-call
7: normal
8: send-intercept
9: normal
10: normal
11: normal
12: normal
13: normal
14: normal
15: normal
Issue 1
June 1999
74Brazil
Page 3 of 3
MULTIFREQUENCY-SIGNALING-RELATED SYSTEM PARAMETERS
OUTGOING FORWARD SIGNAL TYPES OUTGOING BACKWARD SIGNAL TYPES
(Tones to CO) (Tones from CO)
Group-I Group-II Group-A Group-B
12: ani-not-avail 2: normal 1: next-digit 1: free
15: end-of-ani 1: attendant 2: restart 2: busy
6: data-call 3: end-of-dial 3: congestion
4: congestion 4: congestion
5: send-ani 5: free
6: congestion 6: free
7: last-2-digits 7: intercept
8: last-3-digits 8: congestion
9: last digit 9: congestion
10: congestion 10: congestion
11: congestion 11: congestion
12: congestion 12: congestion
13: congestion 13: congestion
14: congestion 14: congestion
15: congestion 15: congestion
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
June 1999
Application Notes for Type Approval
System Parameters Country-Options
Page 1 of 7
SYSTEM PARAMETERS COUNTRY-OPTIONS
Companding Mode: Mu-Law Base Tone Generator Set: 1
Digital Loss Plan: 1 Version of Digital Loss Plan: _
64/84xx Display Character Set: Roman
TONE DETECTION PARAMETERS
Tone Detection Mode: 1
Interdigit Pause: short
440Hz PBX-dial Tone? n 440Hz Secondary-dial Tone? n
Analog Ringing Cadence: 3 Set Layer 1 timer T1 to 30 seconds? n
Analog Line Transmission: _
In Analog Line Transmission field, set to 23 for 900 ohms or set to 16 for 600
ohms.
Issue 1
75Brazil
Page 2 of 7
SYSTEM PARAMETERS COUNTRY-OPTIONS
Tone Name Cadence Tone
Step (Frequency/Level)
PBX-Dial 1: (425/-11)(950)
2: (silence)(50)
3: (goto)(1)
4:
5:
6:
7:
8:
9:
10:
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
June 1999
Application Notes for Type Approval
Page 3 of 7
SYSTEM PARAMETERS COUNTRY-OPTIONS
Tone Name Cadence Tone
Step (Frequency/Level)
Secondary Dial 1: (425/-11)(5000)
2: (goto)(1)
3:
4:
5:
6:
7:
8:
9:
10:
Page 4 of 7
Issue 1
76Brazil
SYSTEM PARAMETERS COUNTRY-OPTIONS
Tone Name Cadence Tone
Step (Frequency/Level)
Ringback 1: (425/-11)(1000)
2: (silence)(4000)
3: (goto)(1)
4:
5:
6:
7:
8:
9:
10:
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
June 1999
Application Notes for Type Approval
Page 5 of 7
SYSTEM PARAMETERS COUNTRY-OPTIONS
Tone Name Cadence Tone
Step (Frequency/Level)
Busy 1: (425/-11)(250)
2: (silence)(250)
3: (goto)(1)
4:
5:
6:
7:
8:
9:
10:
Issue 1
77Brazil
Page 6 of 7
SYSTEM PARAMETERS COUNTRY-OPTIONS
Tone Name Cadence Tone
Step (Frequency/Level)
Intercept 1: (425/-11)(100)
2: (silence)(100)
3: (goto)(1)
4:
5:
6:
7:
8:
9:
10:
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
June 1999
Application Notes for Type Approval
Page 7 of 7
SYSTEM PARAMETERS COUNTRY-OPTIONS
Tone Name Cadence Tone
Step (Frequency/Level)
Intrusion 1: (425/-17.25)(50)
2: (silence)(2000)
3: (goto)(1)
4:
5:
6:
7:
8:
9:
10:
Page 7 of 7
Issue 1
78Brazil
SYSTEM PARAMETERS COUNTRY-OPTIONS
Tone Name Cadence Tone
Step (Frequency/Level)
Hold 1: (425/-11)(50)
2: (silence)(150)
3: (425/-11)(50)
4: (silence)(12750)
5: (goto)(1)
6:
7:
8:
9:
10:
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
June 1999
Application Notes for Type Approval
Page 7 of 7
SYSTEM PARAMETERS COUNTRY-OPTIONS
Tone Name Cadence Tone
Step (Frequency/Level)
Conference 1: (425/-17.25)(50)
2: (silence)(12750)
3: (goto)(1)
4:
5:
6:
7:
8:
9:
10:
Trunk Group Administration
Issue 1
79Brazil
CO Trunk Group Administration
Page 1 of 10
TRUNK GROUP
Group Number: Group Type: co CDR Reports: y
Group Name: COR: 1 TN: 1 TAC:
Direction: two-way Outgoing Display? n
Dial Access? n Busy Threshold: 99 Night Service:
Queue Length: 0 Country: 1 Incoming Destination:
Comm Type: voice Auth Code? n Digit Absorption List:
Prefix-1? n Trunk Flash? n Toll Restricted? n
TRUNK PARAMETERS
Trunk Type: loop-start
Outgoing Dial Type: tone Cut-Through? n
Trunk Termination: 600 Disconnect Timing(msec): 500
Auto Guard? y Call Still Held? y Sig Bit Inversion: none
Terminal Balanced? y RA Trunk Loss: 0db
Trunk Gain: high
Disconnect Supervision - In? n Out? n Cyclical Hunt? n
Answer Supervision Timeout: 10 Receive Answer Supervision? n
For 900 ohm operation, if the Country field is 16 or 23, set the Version field to a (if
Country 5 signaling is to be used) or b (if Country 1 signaling is to be used).
NOTE:
The following is valid only on TN465CV2 or later circuit packs.
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
To enable 600-ohm operation, set the:
16
■ Country field set to
or
23
Issue 1
June 1999
80Brazil
■ Version field to
a
To enable 900-ohm operation, set the:
16
■ Country field set to
■ Version field to
Page 2 of 10
TRUNK FEATURES
ACA Assignment? n Measured: none
Maintenance Tests? y
Data Restriction? n
Abandoned Call Search? n
Suppress # Outpulsing? y
Page 3 of 10
TRUNK GROUP
ADMINISTRABLE TIMERS
Incoming Disconnect(msec): 500 Outgoing Disconnect(msec): 500
Outgoing Dial Guard(msec): 1600
Incoming Glare Guard(msec): 1500 Outgoing Glare Guard(msec): 1500
Ringing Monitor(msec): 5200 Incoming Seizure(msec): 500
Outgoing End of Dial(sec): 10 Outgoing Seizure Response(sec): 5
Programmed Dial Pause(msec): 1500
Flash Length(msec): 540
b
or
23
END TO END SIGNALING
Tone(msec): 350 Pause(msec): 150
OUTPULSING INFORMATION
PPS: 10 Make(msec): 40 Break(msec): 60 PPM? n
NOTE:
If the Country field is 23, Block Collect Call is enabled. Set the Flash Length field to
2000
.
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
June 1999
Application Notes for Type Approval
Page 4 of 10
TRUNK GROUP
Administered Members (min/max): 0/0
Total Administered Members: 0
GROUP MEMBER ASSIGNMENTS
Port Code Sfx Name Night Mode Type Ans Delay
1:
2:
3:
DIOD Trunk Group Administration
Page 1 of 10
Issue 1
81Brazil
TRUNK GROUP
Group Number: Group Type: diod CDR Reports: y
Group Name: COR: 1 TN: 1 TAC:
Direction: two-way Outgoing Display? n
Dial Access? n Busy Threshold: 99
Queue Length: 0 Country: 16
Auth Code? n Digit Absorption List:
Prefix-1? n Trunk Flash? n Toll Restricted? n
TRUNK PARAMETERS
Trunk Type: immed-start
Outgoing Dial Type: mf Incoming Dial Type: mf
Trunk Termination: 600
Digit Treatment: Digits:
Expected Digits: Sig Bit Inversion: none
Terminal Balanced? y RA Trunk Loss: 0db
Trunk Gain: high Drop Treatment: busy
Disconnect Supervision - In? y Out? n
Answer Supervision Timeout: 10 Receive Answer Supervision? n
Page 2 of 20
TRUNK FEATURES
ACA Assignment? n Measured: none
Maintenance Tests? y
Data Restriction? n
Suppress # Outpulsing? y
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
Page 3 of 10
TRUNK GROUP
ADMINISTRABLE TIMERS
Incoming Disconnect(msec): 500 Outgoing Disconnect(msec): 500
Incoming Dial Guard(msec): 70 Outgoing Dial Guard(msec): 1600
Incoming Glare Guard(msec): 1500 Outgoing Glare Guard(msec): 1500
Ringing Monitor(msec): 5200 Incoming Seizure(msec): 500
Outgoing End of Dial(sec): 10 Outgoing Seizure Response(sec): 5
Programmed Dial Pause(msec): 1500
Flash Length(msec): Incoming Incomplete Dial Alarm(sec): 255
END TO END SIGNALING
Tone(msec): 350 Pause(msec): 150
OUTPULSING INFORMATION
PPS: 10 Make(msec): 40 Break(msec): 60 PPM? n
Issue 1
June 1999
82Brazil
Page 4 of 10
TRUNK GROUP
Administered Members (min/max): 0/0
GROUP MEMBER ASSIGNMENTS Total Administered Members: 0
Port Code Sfx Name Night Mode Type Ans Delay
1:
2:
3:
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
DID Trunk Group Administration
Page 1 of 10
TRUNK GROUP
Group Number: Group Type: did CDR Reports: y
Group Name: COR: 1 TN: 1 TAC:
Country: 16
Auth Code? n
TRUNK PARAMETERS
Trunk Type: immed-start Incoming Rotary Timeout(sec): 5
Incoming Dial Type: tone
Trunk Termination: 600 Disconnect Timing(msec): 500
Digit Treatment: Digits:
Expected Digits: Sig Bit Inversion: none
Terminal Balanced? y RA Trunk Loss: 0db
Extended Loop Range? n Trunk Gain: high Drop Treatment: busy
Disconnect Supervision - In? y
Issue 1
June 1999
83Brazil
Page 2 of 10
TRUNK FEATURES
ACA Assignment? n Measured: none
Maintenance Tests? y
Data Restriction? n
Suppress # Outpulsing? y
Page 3 of 10
TRUNK GROUP
ADMINISTRABLE TIMERS
Incoming Disconnect(msec): 500
Incoming Dial Guard(msec): 70
Flash Length(msec): 540 Incoming Incomplete Dial Alarm(sec): 255
END TO END SIGNALING
Tone(msec): 350 Pause(msec): 150
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
Page 4 of 10
TRUNK GROUP
Administered Members (min/max): 0/0
GROUP MEMBER ASSIGNMENTS Total Administered Members: 0
Port Code Sfx Name
1:
2:
3:
Digital Trunk Administration
This section does not list all possible valid administrable combinations: Rather
the most common or standard combination, compatible with public-network and
Type Approval standards for each country, is presented:
Issue 1
June 1999
84Brazil
DS1 for CO, DID and DIOD trunks to the PTT
using digital trunks
Page 1 of 1
DS1 CIRCUIT PACK
Location: Name: E-1CO, DID, DIOD
Bit Rate: 2.048 Line Coding: hdb3
Signaling Mode: CAS
Interconnect: CO Country Protocol: 16
Interface Companding: alaw CRC? n
Idle Code: 01010100
MAINTENANCE PARAMETERS
Slip Detection? n Near-end CSU Type: other
ISDN-PRI (Private Network) Signaling This example assumes use of US Option 1
with facility associated signaling. Other feature options require changes in one or
more administered items.
DS1 Administration screen
■ Circuit Pack: TN464D (or TN464C from upgrades)
■ Bit Rate: 2.048
■ Interface Companding: A-law
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
■ Line Coding: HDB3
■ Signaling Mode: isdn-pri
■ Country Protocol: 1
■ Connect: pbx
■ Interface: user
■ CRC: No
■ Idle Code: 01010100
Signaling Group screen
■ Assoc i ate d Signalin g: Yes
■ Primary D_Channel: xxxx16 (xxxx=>depends on CP physical location)
Trunk Group Administration screen
■ Grou p Type: isdn-pri
■ Service Type: tie
Issue 1
June 1999
85Brazil
ISDN-PRI (P ublic Network)
Not available for this country.
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
Canada & U.S.
Table 20 shows the recommended circuit packs.
Table 20. Recommended and Available CPs in Canada & U.S.
Equipment Equipment Type
Cabinet Type & Power GAC-MCC AC-MCC DC-MCC AC-SCC
DC-SCC AC-CSCC AC-CMC
AC Power Voltage & Freq 120V/60Hz 208V/60Hz 240V/60Hz
Ring Generator 20Hz
Tone Detector >TN2182B >TN744D TN748D TN748C
Tone Clock >TN2182B TN780 TN768
R2MFC Circuit n/a
Speech Synthesizer >TN725B
Issue 1
June 1999
86Canada & U.S.
Call Classifier >TN2182B, >TN744D TN744B
Announcement TN750C TN750B TN750
Analog DID Trunk >TN753
Analog CO Trunk (No PPM) >TN747B
Analog CO Trunk (w/PPM) n/a
4 Wire Tie Trunk >TN760D
2 Wire Tie Trunk n/a
Auxiliary Trunk >TN763D TN763C TN763B
Digital CO/DID Trunk >TN464F TN464E TN464D TN767
Digital Tie Trunk >TN464F TN464E TN464D TN767 TN722B
Digital PRI CO Trunk >TN464F TN464E TN464D TN767
Digital BRI Trunk
Digital Converter PRI-DASS
Digital Converter PRI-DPNSS
Digital Converter PRI-BRI
8 Port Analog Line TN742
16 Port Analog Line >TN746B TN746
4 Wire Digital Line >TN754B
Continued on next page
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
Tab le 20 . Recommended and Available CPs in Canada & U.S. — Continued
Equipment Equipment Type
2 Wire Digital Line >TN2224 TN2181
Data Line >TN726B
BRI-U Line TN2198
BRI-ST Line TN556B
Administration
Issue 1
June 1999
87Canada & U.S.
Continued on next page
All timers and option selections default to the values appropriate for operation in
the US. Whenever a Country Code is requested, use Code 1.
3
3. The default Country Code value is always ‘‘1’’ (US).
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
Chile
Table 21 shows the recommended circuit packs.
Table 21. Recommended and Available CPs in Chile
Equipment Equipment Type
Cabinet Type & Power GAC-MCC AC-MCC DC-MCC AC-SCC
DC-SCC AC-CSCC AC-CMC
AC Power Voltage & Freq 220V/50Hz
Ring Generator 20Hz
Tone Detector >TN2182B >TN744D TN748D TN748C
Tone Clock >TN2182B TN780 TN768
R2MFC Circuit
Speech Synthesizer >TN725B
Issue 1
June 1999
88Chile
Call Classifier >TN744D
Announcement >TN750C TN750B
Analog DID Trunk
Analog CO Trunk (No PPM) >TN747B
Analog CO Trunk (w/PPM)
4 Wire Tie Trunk >TN760D
2 Wire Tie Trunk
Auxiliary Trunk >TN763D
Digital CO/DID Trunk >TN464F TN464E TN464D TN464C
Digital Tie Trunk >TN464F TN464E TN464D TN464C
Digital PRI CO Trunk
Digital BRI Trunk
Digital Converter PRI-DASS
Digital Converter PRI-DPNSS
Digital Converter PRI-BRI
8 Port Analog Line
16 Port Analog Line >TN746B
24 Port Analog Line n/a
Continued on next page
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
Tab le 21 . Recommended and Available CPs in Chile — Continued
Equipment Equipment Type
4 Wire Digital Line >TN754B
2 Wire Digital Line >TN2224 TN2181
Data Line
BRI-U Line
BRI-ST Line
Feature Administration
The screen displays shown in this section were effective the date the type
approval was awarded. The screens may have changed since that date.
Issue 1
June 1999
89Chile
Continued on next page
Only those feature-related parameters that may have a Type Approval or basic
connectivity implication for a particular country are listed here.
NOTE:
Block Collect Call requires TN753 v22 or later for DID trunks,and TN464F
v9 or later for DS1 trunks, and TN465C (all vintages) for analog CO trunks.
■ ARS/AAR Administration
To enable ARS administration, on the System-Parameters
Customer-Options screen, set the
ARS
field to y. You also should check all
ARS/AAR defaults. These defaults were intended for U.S. operation and
certain values are likely to be inappropriate internally. In particular, the
following call types (appear as AR S / AAR default s) typically are not us ed in
non-North American ARS/AAR tables:
fnpa: North American numbers with an area code.
hnpa: North American numbers without an area code.
Lucent recommends the following call types be used:
int: For all international numbers.
natl: For all national PN numbers.
pubu: For all other external (that is, not extensions) numbers.
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
System Parameters Administration
Only those feature-related parameters that may have a Type Approval or basic
connectivity implication for a particular country are listed here.
Feature-related System Parameters
Page 1 of 6
FEATURE-RELATED SYSTEM PARAMETERS
Trunk-to-Trunk Transfer: all
Coverage - Subsequent Redirection No Answer Interval: 2
Coverage - Caller Response Interval (seconds): 4
Keep Held SBA at Coverage Point? y
Automatic Callback - No Answer Timeout Interval (rings): 3
Call Park Timeout Interval (minutes): 10
Off-Premises Tone Detect Timeout Interval (seconds): 20
AAR/ARS Dial Tone Required? y
Music/Tone on Hold: none
Music (or Silence) on Transferred Trunk Calls? no
DID/Tie/ISDN Intercept Treatment: attd
Internal Automatic Answer for Attendant Extended Calls? n
Automatic Circuit Assurance (ACA) Enabled? n
Issue 1
June 1999
90Chile
Page 2 of 6
FEATURE-RELATED SYSTEM PARAMETERS
LEAVE WORD CALLING PARAMETERS
Maximum Number of Messages Per Station (when MSA not in service):10
Stations with System-wide Retrieval Permission (enter extension)
1: 2: 3: 4: 5:
6: 7: 8: 9: 10:
WARNING! SEE USER DOCUMENTATION BEFORE CHANGING TTI STATE
Terminal Translation Initialization (TTI) Enabled? n
External Coverage Treatment for Transferred Incoming Calls? n
SECURITY VIOLATION NOTIFICATION (SVN) PARAMETERS HAVE MOVED TO
THE SYSTEM-PARAMETERS SECURITY SCREEN
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
Page 3 of 6
FEATURE-RELATED SYSTEM PARAMETERS
Reserved Slots for Attendant Priority Queue: 5
Time before Off-hook Alert: 10
Emergency Access Redirection Extension:
Service Observing Warning Tone? y
Number of Emergency Calls Allowed in Attendant Queue: 5
Call Pickup Alerting? n
Deluxe Paging and Call Park Timeout to Originator? n
Controlled Outward Restriction Intercept Treatment: tone
Controlled Termination Restriction (Do Not Disturb): tone
Controlled Station to Station Restriction: tone
AUTHORIZATION CODE PARAMETERS Authorization Codes Enabled?
Authorization Code Length:
Authorization Code Cancellation Symbol: #
Attendant Time Out Flag? n
Display Authorization Code? y
Issue 1
June 1999
91Chile
Page 4 of 6
FEATURE-RELATED SYSTEM PARAMETERS
SYSTEM PRINTER PARAMETERS
System Printer Extension: Lines Per Page: 60
SYSTEM-WIDE PARAMETERS
Switch Name:
CALL CENTER SYSTEM PARAMETERS
Direct Agent Announcement Extension:
Direct Agent Announcement Delay:
Converse Delay Data1: 0 Data2: 2
Direct Agent Announcement Extension: Converse Pulse ON: 100 OFF: 70
Prompting Timeout (secs): 10
CALL MANAGEMENT SYSTEM PARAMETERS
BCMS/VuStats Measurement Interval: hour
BCMS/VuStats Abandon Call Timer (seconds): Validate Login IDs? n
ACD Login Identification Length: Adjunct CMS Release:
MALICIOUS CALL TRACE PARAMETERS
Apply MCT Warning Tone? n MCT Voice Recorder Trunk Group:
DEFINITY® Enterprise Communications Server Application Notes
for Type Approval
Application Notes for Type Approval
Page 5 of 6
FEATURE-RELATED SYSTEM PARAMETERS
Public Network Trunks on Conference Call: 5 Auto Start? n
Conference Parties with Public Network Trunks: 6 Auto Hold? n
Conference Parties without Public Network Trunks: 6 Attendant Tone? y
Night Service Disconnect Timer (seconds): 180 Bridging Tone? n
Short Interdigit Timer (seconds): 3 Conference Tone? n
Unanswered DID Call Timer (seconds): Intrusion Tone? n
Line Intercept Tone Timer (seconds): 30
DID Busy Treatment: tone
Allow AAR/ARS Access from DID/DIOD? n
DISTINCTIVE AUDIBLE ALERTING
Internal: 1 External: 2 Priority: 3
Attendant Originated Calls: external
Page 6 of 6
Issue 1
June 1999
92Chile
FEATURE-RELATED SYSTEM PARAMETERS
Pull Transfer: n Update Transferred Ring Pattern? n
Outpulse Without Tone? y Wait Answer Supervision Timer? n
Repetitive Call Waiting Tone? n
Allow Conference via Flash? y
Vector Disconnect Timer (min): Network Feedback During Tone Detection? y
Hear Zip Tone Following VOA? n
Intercept Treatment On Failed Trunk Transfers? n
Station Tone Forward Disconnect: silence
Level Of Tone Detection: precise
RECALL TIMING
Flashhook Interval? y Upper Bound (msec): 1000
Lower Bound (msec): 200
ENHANCED DCS
Enhanced DCS Enabled? n
Apply Intercept Locally? y Enforce PNT-to-PNT Restrictions? n
Loading...